SPMR 120308 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precision finishing, low cutting forces, and consistent chip control for improved turning performance and surface quality. Order the SPMR120308 NS9530 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. SPMR120308 NS9530 ISO turning insert — finishing cermet by Tungaloy A SPMR120308 NS9530 ISO turning insert engineered for finishing operations on steel, offering a sharp cutting edge for continuous cuts and fine surface finishes. Finishing uncoated cermet grade NS9530 Low cutting forces for fine surface finish ISO SPMR120308 square 90° form, 0.8 mm radius Single-sided chipbreaker for continuous cuts Delivering consistent finishing and superior surface quality The insert is designed as a finishing grade made from cermet, optimised to produce excellent surface finishes with minimal follow-up work. The combination of a sharp cutting edge and low cutting forces reduces rubbing and smearing, which helps to maintain dimensional accuracy when performing light passes. For practical terms, cermet materials provide higher hot hardness and a more stable edge than conventional grades, making them particularly suitable for continuous turning where consistent surface quality is required. Predictable chip control and process stability for turning Equipped with a single-sided chipbreaker, this insert stabilises chip formation during steady cutting conditions, especially at small depths of cut. The chipbreaker geometry supports the generation of short, manageable chips in uninterrupted cuts and contributes to a reduced risk of built-up edge. As a result, the machining process benefits from improved tool life and less operator intervention, supporting higher throughput in production runs. The classification as an uncoated cermet emphasises its role in precision finishing rather than heavy roughing. Compatibility and practical workshop advantages Designed to the ISO specification and supplied in a square 90° form with a 0.8 mm corner radius, the insert integrates into standard ISO turning systems where form, clearance, tolerance class, fastening method, size and thickness match. The modest thickness and precise geometry allow easy seating in holders that accept SPMR120308-type plates, simplifying tooling logistics. For workshops aiming to streamline finishing processes, the insert offers a reliable option for steel machining where fine surface quality, repeatability and low cutting forces are priorities. Contact Metav Werkzeuge to discuss how the SPMR120308 NS9530 finishing insert can be integrated into existing turning workflows, or request tailored cutting data and availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6998511 Manufacturer SKU: TUN6998511 SKU: 6998511-Tungaloy Name: SPMR120308 NS9530 Manufacturer: Tungaloy Facts Shape: quadratisch (square) Size: 12 mm Thickness: 3.18 mm Corner radius: 0.8 mm Clearance angle: 11° Lead angle: 90° Grade: NS9530 (uncoated cermet) Chipbreaker: einseitig (single-sided) Special features Material: Hartmetall Application: Drehen (Turning) Typical use: Außen- und Innendrehen (external and internal turning) Suitability: finishing, continuous cuts, small depths of cut System components: ISO insert, matching outer holder or boring bar, shim/clamp set, replacement screws FAQ What materials is this insert intended for? The NS9530 finishing grade is formulated for machining Stahl (steel), providing a sharp edge and low cutting forces that favour high surface quality in steel turning operations. How does the single-sided chipbreaker affect performance? A single-sided chipbreaker on this insert promotes stable chip formation during continuous turning, reducing the risk of built-up edge and helping to maintain consistent surface finish and tool life. Is the insert compatible with standard ISO holders? Yes; the SPMR120308 design follows ISO specifications and requires a matching holder with the correct form, clearance angle, tolerance class, fastening method, size and thickness for secure clamping. Which features support finishing operations specifically? The combination of an uncoated cermet grade, a sharp cutting edge, and low cutting forces reduces rubbing and improves surface quality, making the insert particularly suitable for finishing passes and light feeds. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 120308 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide, a universal T5115 grade for cast iron and a compact 0.8 mm corner radius to secure consistent chip control and long tool life; order through Metav Werkzeuge or consult our team for compatibility advice. SPMR 120308 T5115 square ISO turning insert by Tungaloy — CVD-coated carbide, 0.8 mm radius SPMR120308 T5115 is a square ISO indexable turning insert designed for general turning applications on cast iron, featuring a one-sided chipbreaker and a robust CVD-coated carbide substrate. CVD-coated carbide for long edge life Universal grade for cast iron machining Square ISO insert for stable positioning One-sided chipbreaker for predictable chips Consistent productivity for cast iron turning The combination of a CVD-coated carbide substrate and the T5115 grade delivers a balanced compromise between wear resistance and edge stability, which is particularly beneficial for casting materials. The coating reduces adhesion and thermal wear, extending the interval between indexings or insert changes; this translates into fewer interruptions on the shop floor and improved throughput. For production environments where reproducible results matter, the insert’s one-sided chipbreaker ensures controlled chip formation and evacuation, reducing the risk of reruns and machine downtime. Geometry and clamping that support accurate cuts Designed to ISO dimensions, the square indexable insert offers reliable seating and repeatable orientation in compatible holders. The 0.8 mm corner radius supports a good balance between edge strength and surface finish, making it suitable for both finishing passes and light-medium stock removal. The insert’s 11° relief angle and 90° insert corner geometry provide stable engagement with the workpiece, helping to maintain consistent cutting forces and minimise vibration during turning operations. Predictable tool life and process security Thanks to the combination of carbide substrate and CVD treatment, the grade resists abrasive wear typical when machining cast iron. This predictable wear behaviour supports process planning: cycle times and tool-change intervals can be estimated with greater confidence, improving cost-efficiency in batch production. Where surface integrity matters, the insert’s construction contributes to repeatable finishes and lowers scrap rates, aligning with objectives for high process reliability and steady output quality. Practical compatibility and selection guidance The insert is supplied in the ISO designation SPMR120308 and is intended for use with matching external toolholders or boring bars; compatibility is determined by insert shape, clearance angle, tolerance class, clamping method, size and thickness. The design has no hole, is square, and measures 12 mm with a plate thickness of 3.18 mm, making it straightforward to match with standard ISO clamping systems. Select a holder that complements the insert’s one-sided chipbreaker and the intended feed and speed range to achieve the best balance of performance and economy. Choose the Tungaloy T5115 grade for reliable cast iron turning — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to confirm compatibility and request availability Technical data Article number: 6864747 Manufacturer SKU: TUN6864747 SKU: 6864747-Tungaloy Numbers / Core technical data ISO designation: 120308 Size: 12 mm Plate thickness: 3.18 mm Corner radius: 0.8 mm Relief angle: 11° Insert angle: 90° Designs / Special features CVD-coated carbide Grade: T5115 (universal for cast iron) One-sided chipbreaker Square insert form No hole ISO turning insert series FAQ What materials is this insert optimised for? The T5115 grade is formulated as a universal option for machining cast iron; the SPMR120308 T5115 insert performs best when turning various cast-iron grades. How is the insert mounted in a holder? Mounting requires a compatible ISO external holder or boring bar that matches the insert’s square form, thickness and clamping method; the insert has no hole and uses standard clamping systems. Which edge radius should be chosen for finishing? The 0.8 mm corner radius on this insert offers a compromise between edge strength and surface finish; for finer finishes, a smaller radius insert would be selected, while heavier cuts benefit from larger radii. Is the coating suitable for higher cutting speeds? The CVD coating improves thermal and abrasive resistance, making the insert suitable for productive cutting speeds typically used for cast-iron turning under stable conditions. How does the chipbreaker affect machining? The one-sided chipbreaker provides controlled chip formation and evacuation, which reduces the likelihood of snarled chips and supports consistent surface quality during turning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 120308 T9225 Wendeplatten - Tungaloy
Take advantage of a CVD‑coated carbide grade designed for robust, mid-to-heavy steel turning and ISO compatibility; the T9225 specification delivers toughness for variable and slightly interrupted cuts while the square SPMR120308 geometry with a 0.8 mm corner radius ensures repeatable seating and secure clamping. Order directly via Metav Werkzeuge or contact the consultants for tailored application advice. SPMR 120308 T9225 SPMR Turning Insert – Tungaloy (CVD‑coated carbide, 11° relief) SPMR 120308 T9225 is an ISO‑standard square turning insert engineered for external and internal turning where robustness and reliable edge life are required CVD‑coated carbide grade T9225 For medium to heavy steel turning ISO‑standard square insert 11° relief angle for stable engagement Consistent cutting performance for robust steel turning The insert pairs a CVD‑coated surface with a carbide substrate to balance wear resistance and toughness. This combination, reflected in the T9225 designation, reduces flank and crater wear under mixed cutting conditions and extends in‑service life where feed and depth of cut vary. The square geometry and the defined 0.8 mm corner radius help maintain cutting edge stability, which supports consistent part tolerances and fewer tool changes, improving overall process efficiency and uptime. Straightforward ISO compatibility and secure clamping Designed to the ISO designation, the insert's form, 11° clearance, size and thickness determine compatibility with matching holders and boring bars. The listed dimensions — 12 mm across the insert, 3.18 mm thickness and the holeless design — should be checked against the toolholder seat, clamp type and tolerance class before selection. Correct pairing of holder and insert simplifies set‑up, reduces vibration and preserves repeatable seating, which in turn improves surface finish and cycle‑time stability. Built for interrupted cuts and variable engagement The T9225 grade is a universal, robust choice for medium to heavy steel machining and performs well under slightly interrupted cutting conditions. The one‑sided chipbreaker supports controlled chip formation and evacuation in common turning operations, reducing the risk of edge chipping when cut conditions fluctuate. This makes the insert suited to batch production and mixed‑geometry parts where short interruptions or changes in engagement occur. Handling, indexing and operational advice The holeless, square plate is indexed according to the geometry of the seat and requires the correct clamp or pocket to ensure positive locking. The insert’s form supports multiple usable edges when indexed; care during clamping prevents deformation and preserves repeatable accuracy. For best results, match the insert grade and chipbreaker to workpiece material and rigidity of the machine set‑up. If in doubt, consult the application data from the toolholder manufacturer or request cutting parameter guidance from Metav Werkzeuge. For application advice, stock information or recommendations for Tungaloy T9225 inserts contact Metav Werkzeuge at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 6781149 Manufacturer SKU: TUN6781149 SKU: 6781149-Tungaloy ISO designation: SPMR120308 Core dimensions and measurable data Insert size: 12 mm Thickness: 3.18 mm Corner radius: 0.8 mm Relief angle: 11° Geometry angle: 90° Hole style: without hole Designs and special features Coating: CVD‑coated Substrate: carbide Grade: T9225 Chipbreaker: one‑sided Shape: square Application: external and internal turning Typical system: ISO turning insert with matching holder, shim and clamp set FAQ Is this insert suitable for turning steel? Yes. The SPMR120308 T9225 insert is specified as a robust universal grade for mid‑to‑heavy steel turning and is optimised for variable engagement and slightly interrupted cuts. Which dimensions are essential to check for holder compatibility? Check the insert size (12 mm), thickness (3.18 mm), 0.8 mm corner radius and the 11° relief angle; confirm the seat form and tolerance class of the intended holder against these values before mounting the insert. What coating and substrate are used on this insert? The insert uses a CVD‑coated carbide substrate; the T9225 coating/substrate combination is selected for balanced wear resistance and toughness in steel machining. Is the chipbreaker suitable for interrupted cuts? Yes. The one‑sided chipbreaker combined with the robust T9225 grade supports controlled chip formation and greater resistance to edge chipping under lightly interrupted or variable cutting conditions. For which turning operations is this insert intended? The design and geometry are intended for both external and internal turning tasks within ISO‑standard tool systems, offering versatility for a range of production and maintenance turning applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 120312 T5115 Wendeplatten - Tungaloy
The ISO compatibility and CVD-coated carbide construction deliver reliable performance and long tool life for cast-iron turning; the 1.2 mm corner radius provides robustness at interrupted cuts. Order the insert directly via Metav Werkzeuge or consult our application specialists for process optimisation. SPMR 120312 T5115 turning insert – ISO square insert, Tungaloy The SPMR120312-CM T5115 Tungaloy insert is an ISO-standard square, indexable insert developed for external and internal turning, optimised for cast-iron applications. ISO-standard square insert for turning CVD-coated carbide grade T5115 1.2 mm corner radius for robust cutting Compatible with standard 90° holders Reliable cutting performance for cast-iron turning The indexable plate is manufactured from carbide with a CVD-coated surface and the T5115 grade, giving a balanced mix of wear resistance and edge stability. This combination is particularly suited to cast iron, where the coating reduces abrasive wear while the substrate supports a sharp, long-lasting cutting edge. The chipbreaker CM guides swarf control to reduce built-up edge and maintain consistent cutting forces. These technical attributes translate directly into fewer insert changes and steadier cycle times during turning operations. Predictable mounting and geometry for process stability ISO standardisation ensures the plate matches holders that conform to the same form, clearance angle and tolerance class; compatibility depends on shape, 11° relief angle, plate thickness and size. The square 12 mm plate with a 90° cutting edge angle allows straightforward indexing for four usable edges, improving economy per insert. The plate’s 3.18 mm thickness and defined 1.2 mm corner radius provide rigidity at the cutting point, helping to avoid vibration in less rigid set-ups and enabling safer interrupted cuts. Explained simply: standardised geometry makes selection and machine set-up more predictable and reduces trial-and-error. Enhanced surface finish and extended tool life A controlled combination of substrate hardness and CVD coating yields better surface quality while extending tool life under typical turning feeds and speeds. The stable cutting edge of this universal grade reduces edge chipping and supports reproducible part quality. Selecting the correct chipbreaker and the CM geometry will further improve swarf formation and surface integrity. For manufacturing environments focused on productivity, the result is fewer reworks and a higher yield of parts meeting tolerance — a measurable benefit to throughput and overall process cost-efficiency. Contact Metav Werkzeuge to discuss the suitability of the Tungaloy SPMR 120312 T5115 insert for specific turning tasks and to receive tailored application advice and availability Technical data Article number: 6864748 SKU: 6864748-Tungaloy Manufacturer SKU: TUN6864748 Model series: ISO-Drehwendeschneidplatten Application: Turning Numbers / Core technical data Corner radius: 1.2 mm Plate size: 12 mm Plate thickness: 3.18 mm Rake/relief angle: 11° Cutting edge angle: 90° Special features Carbide material CVD-coated grade T5115 Chipbreaker CM Square plate form Without hole ISO-standard indexable insert Universal grade optimised for cast iron For external and internal turning FAQ What materials is this insert best suited for? The Tungaloy SPMR 120312 T5115 insert is optimised for cast iron applications; its CVD-coated carbide composition balances wear resistance and edge stability for that material group. How many cutting edges are available on the plate? As a square ISO plate, the insert offers four usable cutting edges when indexed; the 90° geometry supports straightforward indexing for efficient edge use. What does the chipbreaker designation CM indicate? The CM chipbreaker is designed to control swarf form for general turning in materials such as cast iron, improving evacuation and reducing the risk of built-up edge during stable machining. Is this insert compatible with standard ISO holders? The plate follows ISO form and dimensional conventions; compatibility depends on holder form, clearance, tolerance class and mounting size—holders matching the ISO designation will accommodate the plate. Can the insert handle interrupted cuts? The 1.2 mm corner radius and 3.18 mm thickness give the insert added robustness, making it suitable for conditions with occasional interruptions, provided the machining parameters and clamping are appropriate. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP GH330 Wendeplatten - Tungaloy
Combining the GH330 wear-resistant grade with a robust cemented carbide substrate delivers a reliable balance of toughness and edge stability for milling operations; the square geometry and 90° approach angle support precise shoulder and face milling. Order the SPMR1605PP GH330 Tungaloy milling insert directly via Metav Werkzeuge or consult our advisors if further specification is required. SPMR 1605PP GH330 Tungaloy milling insert — square indexable insert for milling SPMR1605PP GH330 is a square indexable insert designed for a range of milling tasks, compatible with Tungaloy milling systems and intended for face, shoulder, groove, high-feed and contour milling when matched to the correct cutter body. GH330 grade for wear resistance Solid carbide substrate for durability Square 16 mm size, 90° cutting angle One-sided chipbreaker for controlled swarf Reliable edge life through a balanced carbide grade The GH330 grade combines wear resistance and sufficient toughness to extend edge life in mixed machining tasks. Manufactured from cemented carbide, this insert is engineered for repeatable performance in serial production where tool-change intervals and consistent part quality matter. By favouring a balanced microstructure, the grade resists abrasive wear while maintaining a stable cutting edge, which reduces the need for frequent index changes and helps sustain cycle-time reliability. Geometry optimised for versatile milling operations The square 16 mm format with a 90° approach angle offers rigidity and predictable chip flow for shoulder and face milling. A 5.56 mm plate thickness supports stable clamping and reduces chatter risk when paired with the appropriate clamping screw and cutter body. The 11° clearance ensures effective engagement and clearance during entry and exit, while the one-sided chipbreaker provides controlled swarf formation for improved surface finish and reduced heat at the cutting edge. These geometry attributes allow the insert to cover a broad set of applications within a single tooling system. System compatibility and productivity in the shopfloor context As part of a matched Tungaloy milling system, the insert functions together with the cutter body, clamping screw and any required shim to form a safe, repeatable interface. Correct seating and geometric matching are essential: the insert seat and cutter geometry must correspond to ensure secure clamping and optimal cutting performance. In production settings, the result is fewer interruptions, predictable tool life and improved material removal rates, delivering measurable improvements to throughput and process stability. Contact Metav Werkzeuge for tailored application advice and to order the SPMR1605PP GH330 Tungaloy milling insert; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 6807218 Manufacturer SKU: TUN6807218 SKU: 6807218-Tungaloy Designation: SPMR1605PP GH330 Tungaloy milling insert Model series: Milling indexable inserts Material: cemented carbide Facts Plate size: 16 mm Plate thickness: 5.56 mm Corner radius: 0 mm Approach angle: 90° Clearance angle: 11° Manufacturer article no.: 6807218 Special features Square plate form One-sided chipbreaker No hole (without hole) ISO designation: 1605PP Grade: GH330 Typical application: face, shoulder, groove, high-feed and contour milling FAQ What materials is this insert suitable for? The SPMR1605PP GH330 Tungaloy milling insert is intended for general milling tasks; the GH330 grade provides a balance suited to a wide range of steels and mixed materials typical in machining shops. How does the one-sided chipbreaker affect finishing? The one-sided chipbreaker on the SPMR1605PP helps control swarf and reduces edge loading, which contributes to more consistent surface quality during shoulder and face milling operations. Is the insert compatible with any cutter body? The insert must be used in a Tungaloy-compatible milling body with a matching insert seat and clamping method; seat, geometry and cutter body must correspond to ensure secure clamping and correct cutting kinematics. What are the critical geometric values to check before use? Verify the plate size (16 mm), plate thickness (5.56 mm), approach angle (90°) and the ISO designation 1605PP to confirm mechanical fit with the milling body and clamping screw. Can this insert be used for high-feed milling? When assigned to the appropriate tool family and cutter body, the SPMR1605PP GH330 insert is suitable for high-feed and contouring operations as stated in the model series application note. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP GH330 Wendeplatten - Tungaloy
Take advantage of the combination of stable edge life, balanced toughness and straightforward system compatibility for reliable milling performance; order the insert directly via Metav Werkzeuge or ask our consultants if needed. SPMR 1605PP GH330 indexable milling insert by Tungaloy — square 16 mm, 11° clearance SPMR1605PP GH330 is a square indexable insert designed for milling operations such as face, shoulder, slot, high-feed and contour milling when used with matching tool bodies and clamping screws. SPMR1605PP GH330 for precision milling Square 16 mm plate, 5.56 mm thickness 11° clearance angle, single-sided breaker Tungaloy carbide grade for wear resistance Consistent tool life through an optimised carbide grade The GH330 grade is formulated to provide a balanced combination of wear resistance and toughness, which leads to longer intervals between index changes and reduced downtime. Used in a milling system where insert seat, geometry and body match precisely, the result is a predictable cutting process with stable tool life. The substrate is carbide, offering hardness needed for abrasive conditions while the grade composition helps maintain edge stability under interrupted cuts. Predictable process results with system compatibility Reliable results are achieved when the insert is installed in a compatible cutter body with the correct clamping screw and, where applicable, a backing pad. The design of this square insert, with its 16 mm size and 5.56 mm thickness, ensures a secure fit and even load distribution across the cutting edge. The 11° clearance reduces rubbing on the flank and supports smoother chip flow, while the single-sided chipbreaker helps control chip shape for commonly encountered milling tasks. These elements together improve surface finish and reduce the risk of unexpected tool failure, supporting efficient, repeatable production. Practical handling and application advantages on the shop floor Selection of this insert simplifies inventory management: a compact, square geometry covers multiple milling tasks such as face and contouring operations depending on the cutter family. The zero corner radius promotes crisp profile definition, and the single-sided configuration allows clear identification of the cutting edge during handling. As part of a milling system, the insert contributes to economic machining by combining durable cutting performance with predictable replacement intervals. For complex setups, application data and toolbody matching should be checked to ensure optimum results. Contact Metav Werkzeuge for application advice on Tungaloy GH330 inserts or to request a compatibility check with existing milling bodies — info@metav-werkzeuge.com | +49 2822 7131930 — Metav Werkzeuge stands ready to assist with technical queries and selection guidance Technical data Article number: 6807216 Manufacturer SKU: TUN6807216 SKU: 6807216-Tungaloy Model series: milling indexable inserts Facts Size: 16 mm Thickness: 5.56 mm Corner radius: 0 mm Clearance angle: 11° Included angle: 90° Special features Grade: GH330 Material: carbide Chipbreaker: single-sided Hole: without hole Plate shape: square Application: milling FAQ What milling operations is this insert intended for? The SPMR1605PP GH330 insert from Tungaloy is intended for face, shoulder, slot, high-feed and contour milling depending on the assigned tool family. How does the GH330 grade affect performance? GH330 provides a balance of wear resistance and toughness, giving the insert durable cutting edges and good performance under varied milling conditions. What are the key dimensional specifications? The insert is a square plate with a 16 mm size, 5.56 mm thickness and a corner radius of 0 mm; the clearance angle is 11°. Does the insert require a specific cutter body or seat? The insert requires a cutter body and seat geometry that are technically matching; proper seating and clamping are essential for reliable performance. Is this a single- or double-sided insert? This is a single-sided insert with a single-sided chipbreaker. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP GH330 Wendeplatten - Tungaloy
Take advantage of the combination of wear-resistant GH330 grade, precise 90° geometry and secure clamping for consistent milling results; order directly via Metav Werkzeuge or consult the specialists for application matching. SPMR 1605PP GH330 — Indexable milling insert for milling, Tungaloy A SPMR1605PP indexable insert designed for Tungaloy milling systems, intended for face, shoulder, slot and high-feed milling where stable cutting edges and predictable wear behaviour are required GH330 grade for wear resistance Square insert 16 mm size 5.56 mm plate thickness Single-sided chipbreaker High productivity through material and geometry The combination of the GH330 cutting grade and a carbide substrate delivers a reliable balance between wear resistance and toughness. This balance reduces unexpected edge chipping and supports longer tool life in continuous milling operations. The insert’s single-sided chipbreaker is engineered to control chip flow and improve surface finish in a variety of steel and alloy applications, contributing to fewer interruptions and higher net machining time. Secure seating and dimensional consistency for repeatable results A precise seating geometry and a defined 90° cutting angle ensure repeatable positioning in compatible toolholders. The 16 mm square form and 5.56 mm plate thickness provide robust clamping, which stabilises the cutting edge under increased feed rates and varying cutting forces. Consistent insert geometry reduces set-up variability and simplifies indexation, supporting predictable cycle times across production batches. Versatile application range and clear system compatibility Engineered for milling, the insert fits Tungaloy milling bodies where the insert seat, geometry and cutter body match technically. The moderate 11° clearance angle and zero corner radius allow flexible use in face, shoulder and high-feed milling tasks while maintaining edge stability. Material compatibility covers common engineering materials where a wear-conscious carbide grade is advantageous, enabling balanced performance across diverse production needs. Practical benefits for process optimisation Using a grade-focused insert reduces planning complexity: the GH330 grade combines abrasion resistance with sufficient toughness to withstand intermittent cuts. This results in reduced tool change frequency and lower process variability. For workshops aiming to improve throughput without increasing set-up effort, the indexable insert supports predictable tool life and simpler inventory management when paired with standard Tungaloy milling systems. Contact Metav Werkzeuge for tailored machining advice on Tungaloy SPMR1605PP GH330 — quote article number 6807222 or call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6807222 Manufacturer SKU: TUN6807222 Model series: Milling indexable inserts ISO designation: SPMR1605PP SKU: 6807222-Tungaloy Facts Insert size: 16 mm Plate thickness: 5.56 mm Clearance (free) angle: 11° Cutting angle: 90° Corner radius: 0 Hole: without hole Special features Material: carbide Grade: GH330 Chipbreaker: single-sided Plate shape: square Application: milling System: Designed for Tungaloy milling systems FAQ What materials is this insert suited for? The insert in GH330 grade is intended for a broad range of engineering materials where a wear-resistant carbide is beneficial; it is commonly used in steel and alloy machining within milling operations. How is the insert mounted in the cutter body? The square insert is seated and clamped in compatible Tungaloy milling bodies; the seating geometry and cutter body must match the insert’s form and ISO designation for secure clamping. What does the chipbreaker provide in practice? The single-sided chipbreaker on this design controls chip formation and evacuation, helping to improve surface finish and reduce the risk of built-up edge during continuous milling. Is the 90° cutting angle suitable for shoulder milling? Yes, the defined 90° geometry is suitable for face and shoulder milling tasks where a robust edge and square shoulder profiles are required. Which identifiers should be quoted when ordering? When ordering, reference the ISO designation SPMR1605PP, article number 6807222 and the manufacturer SKU TUN6807222 to ensure the correct grade and geometry are supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP T1115 Wendeplatten - Tungaloy
Take advantage of the combination of wear-resistant T1115 grade, stable cutting edge and clear system compatibility for consistent milling performance and reduced rework. Order directly via Metav Werkzeuge or contact the consultancy team for application-specific selection. SPMR 1605PP T1115 SPMR — Indexable milling insert for Fräsen by Tungaloy, square 16 mm, 90° cutting angle The SPMR1605PP T1115 is a square indexable insert designed for milling in Tungaloy systems, delivering a balanced mix of wear resistance and edge stability for general-purpose and high-productivity operations. SPMR1605PP T1115 indexable insert for milling Square 16 mm insert, 90° cutting angle 5.56 mm plate thickness, 11° clearance Single-sided chipbreaker, carbide construction Higher productivity through balanced material properties The insert uses the T1115 grade, a Tungaloy carbide formulation that combines wear resistance with sufficient toughness to maintain edge stability during milling cycles. This balance reduces unexpected tool changeovers and supports steady material removal rates, which is particularly relevant for operations that demand repeatable surface quality. Engineers benefit from predictable flank wear behaviour, enabling process parameter optimisation and longer effective tool life. Reliable system fit and versatile application range Compatibility of the insert seat, geometry and cutter body is essential: the plate must be used in matching Tungaloy cutter bodies to ensure clamping integrity and positional accuracy. The square 16 mm format with a 90° cutting angle is suitable for face, shoulder, slot, high-feed and contour milling depending on the chosen tool family. The single-sided chipbreaker supports controlled chip formation in a range of steels and alloys, turning technical specifications into operational reliability on the shop floor. Robust mechanical design for reduced setup and maintenance With a plate thickness of 5.56 mm and a relief angle of 11°, the component offers stable seating and resistance to mechanical deflection under load. The insert's construction in carbide and the single-sided breaker keep mounting and replacement straightforward while preserving cutting performance. Correct assembly with the recommended clamp screw and any necessary support pad ensures secure fixation and consistent cutting geometry, which reduces rework and maintenance intervals. For application advice, tool matching or to request delivery through Metav Werkzeuge, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific milling tasks. Technical data Article number: 6863798 SKU: 6863798-Tungaloy Manufacturer SKU: TUN6863798 Model series: Milling indexable inserts Facts Plate size: 16 mm Plate thickness: 5.56 mm Corner radius: 0 mm Relief angle: 11° Cutting angle: 90° Special features Grade: T1115 Material: carbide Plate shape: square Chipbreaker: single-sided Hole: without hole Application: milling (Fräsen) System compatibility: for Tungaloy milling systems; seat, geometry and cutter body must match Typical applications: face, shoulder, slot, high-feed and contour milling FAQ What machining tasks is this insert suitable for? The SPMR1605PP T1115 insert is intended for milling tasks such as face, shoulder, slot, high-feed and contour milling when used within compatible Tungaloy milling systems. Which material is the insert made from and what are the benefits? The insert is made from carbide in Tungaloy’s T1115 grade, which provides a compromise between wear resistance and toughness for reliable edge life in varied milling applications. How must the insert be mounted for correct operation? Correct operation requires a matching cutter body and clamp system; the insert seat, geometry and cutter body must technically match to ensure secure clamping and reproducible cutting geometry for the SPMR1605PP. Does the insert have a chipbreaker, and what does it do? Yes — the SPMR1605PP features a single-sided chipbreaker designed to control chip formation and evacuation, improving process stability and surface finish in many material groups. Is the SPMR1605PP available in other grades or geometries? This listing describes the T1115 grade; other grades and geometries may be available from Tungaloy to suit different feeds, speeds or workpiece materials — consult Metav Werkzeuge for alternatives and matching cutter bodies. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP T3130 Wendeplatten - Tungaloy
Benefit from the combination of T3130 wear resistance, precise 11° relief and a robust 90° geometry for predictable, productive milling; order the SPMR1605PP inserts via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. SPMR 1605PP T3130 indexable insert for milling — Tungaloy A SPMR1605PP T3130 square indexable insert developed for Tungaloy milling systems, optimised for face, shoulder, slot and contour milling where consistent cutting performance is required Square 16 mm insert for stable milling T3130 grade carbide for wear resistance 11° relief angle for reliable cutting geometry Single-sided chipbreaker, 5.56 mm thickness Increased process reliability through material and grade The SPMR series insert is designed to deliver repeatable results in demanding milling tasks. As an indexable insert in carbide, the T3130 grade combines wear resistance with sufficient toughness to maintain a stable cutting edge over extended cycles. This balance reduces unexpected tool changes and contributes to a steadier production flow. The specification emphasises predictable tool life and consistent surface quality, making the component suitable for mixed batch production where set-up times must be minimised. Geometry and chip control that support productive machining Geometry decisions such as the 11° relief, a 90° approach angle and a single-sided chipbreaker are chosen to optimise chip flow and flank contact during engagement. The 5.56 mm plate thickness and square 16 mm format support rigidity in the toolholder and reduce vibration, which in turn improves dimensional stability and surface finish. In practice, this leads to fewer rework cycles and a clearer process window for feed and speed adjustments when integrating into existing milling systems. Application versatility and easy integration into systems Suitable for face, shoulder, slot, high-feed and contour milling depending on the assigned tool family, the insert suits a broad range of steel and cast-iron operations typical in component manufacture. The square form with zero corner radius offers straightforward indexing options and multiple cutting edges per insert, enhancing economy per cutting edge. Compatibility with the Tungaloy milling bodies requires matched seat and clamping hardware; when those conditions are met, the insert helps improve cycle times through stable cutting and predictable wear progression. For tailored technical advice or to request a quote for Tungaloy SPMR1605PP inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6853854 SKU: 6853854-Tungaloy Manufacturer SKU: TUN6853854 Model series: Fräswendeschneidplatten Facts Insert size: 16 mm Thickness: 5.56 mm Relief angle: 11° Approach angle: 90° Corner radius: 0 mm ISO designation: 1605PP Special features Material: Hartmetall (carbide) Grade: T3130 Shape: square Hole style: without hole Chipbreaker: single-sided Intended application: milling System compatibility: for Tungaloy milling systems FAQ What materials is this insert suitable for? The SPMR1605PP T3130 insert is a carbide grade designed for a wide range of machining tasks, particularly effective on steel and cast-iron when used within recommended cutting parameters. How does the T3130 grade affect performance? The T3130 grade on the SPMR1605PP provides a balance of wear resistance and toughness, extending edge life while preserving cutting-edge stability in interrupted and continuous milling. Is the insert compatible with all milling bodies? Compatibility requires that the insert seat, geometry and milling cutter body are technically matched; the SPMR1605PP is intended for use in Tungaloy milling systems with the correct seat and clamping arrangement. How many cutting edges are available per insert? As a square insert with a zero corner radius, the component offers multiple index positions; the exact number depends on the mounted orientation and toolholder design for the milling family. What is the ISO designation and thickness of the insert? The insert carries the ISO designation 1605PP and a plate thickness of 5.56 mm, aligning with standard housing dimensions for the corresponding tool families. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP T3130 Wendeplatten - Tungaloy
Combining the T3130 carbide grade with a square 90° geometry delivers reliable wear resistance and edge stability for consistent milling performance. Order the insert directly via Metav Werkzeuge or contact our technical consultants for matching cutter bodies and mounting guidance. SPMR 1605PP T3130 — milling insert (SPMR) for Fräsen by Tungaloy SPMR 1605PP T3130 is an indexable milling insert for Tungaloy systems, engineered for face, shoulder, slot, high-feed and contour milling where precise geometry and matching cutter bodies are essential Robust carbide grade T3130 Square 16 mm form, 90° cutting angle 5.56 mm thickness, 11° clearance Single-sided chipbreaker for chip control Consistent machining through optimised material and geometry The combination of a carbide substrate and the T3130 grade focuses on balancing wear resistance with edge stability, which directly reduces unplanned tool changes. As an indexable insert with a 90° cutting face and a 16 mm square form, it provides predictable cutting forces and repeatable results in common milling operations. The defined 5.56 mm plate thickness and 11° clearance support stable mounting and minimise vibration, enhancing surface finish and tool life. Benefits such as longer intervals between re-grinds and steady dimensional accuracy help to improve overall process efficiency. Clear compatibility requirements to avoid setup errors This insert is designed for use in Tungaloy milling systems; the platter seat, geometry and cutter body must match to ensure torque transmission and correct clamping. The insert’s specification — including the ISO designation 1605PP and the single-sided chipbreaker — guides selection of the correct cutter body and clamping screw. For workshops and production engineers, this reduces the time spent on trial-and-error setups and lowers the risk of incorrect assembly. If the cutter body is matched to the insert’s geometry, mounting becomes straightforward and repeatable. Practical explanation of technical terms and machining benefits The term indexable insert refers to a replaceable cutting plate that can be rotated or replaced without re-sharpening the entire tool. The single-sided chipbreaker promotes controlled chip formation on one cutting edge, which is especially useful for slotting and shoulder milling where chip evacuation matters. A corner radius of 0 mm gives a sharp cutting edge for precise shoulder faces and narrow slots, while the square plate shape supports robust cutting edges on four sides, lowering the cost per cutting edge over the tool life. Where this insert adds most value in production Typical applications include planing, shoulder milling, slotting, high-feed and contour milling within compatible tool families. The T3130 grade’s balance of toughness and wear resistance suits mixed batches of common steels and cast materials where sudden interruptions in cut or varying engagement can occur. For production managers, this translates to more consistent cycle times and reduced scrap rates. For jobbing shops, the ability to reindex and reuse multiple edges offers economic advantage and reliable surface quality for repeat orders. For assured compatibility and fast supply of Tungaloy inserts such as the SPMR1605PP T3130, contact Metav Werkzeuge for technical advice and procurement: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data Article number: 6853855 SKU: 6853855-Tungaloy Manufacturer SKU: TUN6853855 Item label: SPMR1605PP T3130 Tungaloy-Wendeplatte Manufacturer: Tungaloy Facts Plate size: 16 mm Plate thickness: 5.56 mm Clearance angle: 11° Cutting angle: 90° Corner radius: 0 mm Special features Material: carbide Grade: T3130 Plate form: square Chipbreaker: single-sided Hole: without hole Application: milling Model series: milling indexable inserts System note: requires matching cutter body and clamping screw FAQ What materials is this insert suitable for? The insert in grade T3130 is intended for general milling applications and offers a balanced performance for a broad range of materials when used with the correct cutter body in Tungaloy systems. How is chip control achieved with this insert? Chip control is provided by the single-sided chipbreaker, which promotes predictable chip shapes and improved evacuation during slotting and shoulder milling. Can the insert be used in any milling cutter? The insert requires a cutter body with a compatible seat and geometry; the platter seat, geometry and cutter body must match the insert specifications to ensure secure clamping and correct cutting angles. What benefits does the square 16 mm form offer? The square form delivers four usable cutting edges per insert, improving cost efficiency per edge and providing stable cutting forces for shoulder and face milling operations. Is there a corner radius on this insert? This insert has a corner radius of 0 mm, which gives a sharp cutting edge suitable for precise shoulder milling and narrow slotting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP UX30 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp cutting edge and the UX30 uncoated carbide grade for low cutting forces and consistent chip control; order the SPMR1605PP insert directly via Metav Werkzeuge or ask our consultants if needed. SPMR 1605PP UX30 indexable insert for milling — Tungaloy SPMR1605PP UX30 is a square indexable insert designed for Tungaloy milling systems, optimised for low cutting forces and reliable chip formation in a range of face, shoulder, slot and contour milling applications SPMR geometry for square insert seating Sharp cutting edge for low cutting forces UX30 uncoated carbide for reliable chip control 90° insert angle for versatile milling Constant chip control for stable production The UX30 grade is an uncoated carbide designed to provide a sharp cutting edge and predictable chip formation, which reduces the need for repeated process adjustments. For operations where low cutting forces and consistent chips matter, the geometry and edge preparation of this insert help maintain a steady material flow and reduce vibration. This leads to more uniform tool life and helps secure reproducible component quality in industrial milling. Broad application flexibility with secure seating Compatibility is essential: the insert seat, geometry and cutter body must match technically to guarantee correct clamping and cutting behaviour. The SPMR1605PP form is a square form with a 90° angle, making it suitable for face, shoulder, slot, high-feed and contour milling depending on the assigned tool family. The systematic design—insert, cutter body, clamping screw and, where required, a shim—ensures easy replacement and repeatable positioning in production environments. Technical geometry that supports efficient machining Key dimensional and geometric choices deliver practical benefits: the 16 mm size and 5.56 mm thickness provide a robust cutting edge for stable engagement, while the 11° relief angle supports smooth entry and exit from the cut. The insert is supplied without a hole and features a single-sided chipbreaker, which assists chip control in materials that suit sharp-edge cutters. For manufacturers seeking predictable results and straightforward tool management, these design decisions translate into fewer interruptions and improved machining throughput. For reliable milling with the UX30 grade and expert ordering support, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss tooling options and availability Technical data Article number: 6807221 SKU: 6807221-Tungaloy Manufacturer article number: 6807221 Manufacturer: Tungaloy Model series: Fräswendeschneidplatten Material: Hartmetall Facts Insert designation: SPMR1605PP ISO code: 1605PP Grade/sort: UX30 Size: 16 mm Thickness: 5.56 mm Angle: 90° Relief angle: 11° Corner radius: 0 mm Special features Square form insert Without hole Single-sided chipbreaker Sharp cutting edge for low cutting forces Designed for face, shoulder, slot, high-feed and contour milling System components: insert, cutter body, clamping screw, possible shim Compatible with Tungaloy milling systems FAQ What milling tasks is this insert suitable for? The SPMR1605PP UX30 insert is intended for face, shoulder, slot, high-feed and contour milling tasks when used in the appropriate Tungaloy milling tool family. Which materials does the UX30 grade perform well on? The UX30 uncoated carbide grade is chosen for applications that prioritise low cutting forces and good chip formation; it is best used where a sharp cutting edge and controlled chips improve process stability. How must the insert be matched to the cutter body? Correct performance requires that the insert seat, geometry and cutter body are technically matched; the SPMR form must fit the designated Tungaloy tool holder and be secured with the correct clamping screw and shim where applicable. Is the insert reversible or indexed? The square insert provides indexable edges through rotation; handling and indexing should follow the tool manufacturer's instructions to preserve the sharp edge and chip control of the UX30 grade. What are the key dimensions to check before ordering? Confirm the 16 mm size, 5.56 mm thickness, 90° angle and the SPMR1605PP designation to ensure proper fit and function in the chosen milling system. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMR 1605PP UX30 Wendeplatten - Tungaloy
Take advantage of a combination of precise fit, a sharp cutting edge and the UX30 carbide grade to improve chip control and reduce cutting forces for milling operations. Order the SPMR1605PP insert directly via Metav Werkzeuge or consult the Metav team for application-specific advice. SPMR1605PP 1605PP UX30 indexable milling insert by Tungaloy, for milling applications The SPMR1605PP UX30 is a square, uncoated carbide indexable insert developed for Tungaloy milling systems; designed for face, shoulder, slot, high-feed and contour milling where low cutting forces and reliable chip formation are required. *Sharp cutting edge for low cutting forces *Square 16 mm format, 90° cutting angle *Uncoated carbide grade UX30 for good chip control *One-sided chipbreaker, 5.56 mm plate thickness Precision milling with less force and better chip control The insert is made from uncoated carbide in the UX30 grade, offering a sharp cutting edge that prioritises reduced cutting forces and reliable chip formation. For machining tasks such as face and shoulder milling, the result is stable cutting behaviour and consistent surface quality. The construction is particularly advantageous where minimised force input improves tool life and machine load; this contributes directly to more efficient cycle times and predictable performance. Robust geometry for stable clamping and indexing A square 16 mm format combined with a 90° cutting angle and 5.56 mm thickness provides a stable contact area with the milling body, improving rigidity during operation. The 11° clearance angle reduces rubbing at the flank while the one-sided chipbreaker helps to control chips in a variety of feeds. These geometry choices ensure repeatable positioning and straightforward indexability, supporting long-term process stability on compatible toolholders. Material choice and machining behaviour explained As an uncoated carbide grade, this insert favours low cutting forces and improved chip evacuation compared with some coated alternatives; the design focus is on smooth chip flow and reliable edge life under the intended cutting conditions. The single-sided chipbreaker is optimised for common feed ranges used in face, slot and contour milling, delivering good chip formation and reduced re-cutting. This combination supports productive machining where surface finish and cutting efficiency matter. System compatibility and practical application notes The insert is intended specifically for Tungaloy milling systems: Tungaloy milling systems require that the seat, insert geometry and milling body are technically matched to ensure secure clamping and correct cutting geometry. The insert is supplied without a hole and functions as part of the complete system comprising milling body, insert and clamping screw. For workshop planning, specify the correct insert size and grade to maintain process reliability and to benefit from predictable tool-life characteristics. Contact Metav Werkzeuge for an application review and precise compatibility check for Tungaloy SPMR1605PP UX30 inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6807225 SKU: 6807225-Tungaloy Manufacturer SKU: TUN6807225 Model series: Fräswendeschneidplatten Material: Hartmetall Grade: UX30 Facts Plate size: 16 mm Plate thickness: 5.56 mm Cutting angle: 90° Clearance angle: 11° Corner radius: 0 Special features Square plate form Uncoated carbide (cemented carbide) One-sided chipbreaker Without hole (ohne Loch) For milling (Fräsen) System requirement: matching seat, geometry and milling body FAQ What materials is this insert suited for? The SPMR1605PP UX30 insert is an uncoated carbide grade intended for general milling tasks; the UX30 grade is optimised for applications where low cutting forces and reliable chip formation are required. Is the insert compatible with other milling systems? Compatibility requires matching the insert seat, geometry and milling body; the SPMR1605PP is designed for use in Tungaloy milling systems and must be used with bodies that accept the specified plate form and dimensions. What does the one-sided chipbreaker mean for chip control? The one-sided chipbreaker on this indexable milling insert guides chip flow on the active cutting side, improving evacuation and reducing the risk of chip congestion in many face and slot milling operations. How is the insert clamped in the milling body? The insert is part of a system comprising milling body, insert and clamping screw; secure clamping and correct seating are essential for the intended cutting geometry and process stability with the SPMR1605PP. Can the sharp cutting edge of UX30 improve tool life or finish? The sharp edge and UX30 carbide balance low cutting forces with good chip formation, which often results in consistent surface finish and predictable edge wear for the specified milling applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 AH6225 Wendeplatten - Tungaloy
Take advantage of the PVD-coated AH6225 grade and the 90° square geometry to achieve consistent results in medium turning of stainless steels; the sharp yet stable cutting edge reduces regrinds and keeps cycle times predictable. Order the insert directly via Metav Werkzeuge or consult the team for help selecting the matching holder and clamping kit. SPMT090304 AH6225 Tungaloy turning insert — PVD-coated cemented carbide, ISO square 90° The SPMT090304 AH6225 is an ISO-standard square indexable insert for external and internal turning, engineered for reliable machining of stainless steels and medium cutting conditions. PVD-coated AH6225 carbide for stainless steels Square ISO insert, 90° geometry, 0.4 mm nose radius Cylindrical hole with 40°–60° countersink Designed for external and internal turning operations Reliable edge performance for stainless-steel turning The combination of a PVD-coated surface and a cemented carbide substrate in grade AH6225 provides a balance between a sharp cutting edge and robust edge stability. This results in consistent surface finish and extended intervals between indexings when machining stainless steel under varying conditions. The coating reduces adhesive wear and helps to maintain a defined cutting edge geometry, which is particularly important when tackling work-hardened or abrasive stainless alloys; this translates directly into fewer interruptions on the shop floor and improved process stability. Geometry and mounting that simplify set-up The 90° square shape and a 0.4 mm nose radius promote axial rigidity and allow reliable shoulder and facing operations with reduced vibration. The insert’s 11° relief angle and 3.18 mm thickness are matched to ISO norms, so selection of a compatible holder is straightforward provided form, relief angle, tolerance class, fastening, size and thickness are observed. The cylindrical hole with a 40°–60° one-sided countersink ensures secure clamping and repeatable seating, reducing the need for re-adjustment after replacement and lowering set-up time across production runs. Chip control and application flexibility Equipped with a single-sided chipbreaker, the insert manages chip flow for a wide range of cutting parameters, helping to reduce heat concentration and protect the cutting edge. The chipbreaker and grade are chosen to suit turning operations—both external and internal—so the insert can perform in semi-finishing and medium-machining tasks. As part of a system that includes a matching holder or boring bar, a shim/clamping set and replacement screws, the component supports predictable process outcomes and easier tool management in batch production. Coating and grade benefits for productivity The PVD coating on the AH6225 grade enhances hardness at the cutting edge and improves resistance to built-up edge formation, which is common in stainless-steel machining. This results in more consistent tool life and a stable cutting force profile over time. For operations where repeatability and surface integrity matter, the coated carbide delivers a balance of wear resistance and edge toughness that supports sustained productivity without frequent reconditioning. Contact Metav Werkzeuge for tailored advice on selecting the right ISO turning insert, holder and clamping components for specific stainless-steel applications — expert support available via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 6903310 Manufacturer SKU: TUN6903310 SKU: 6903310-Tungaloy Label: SPMT090304 AH6225 Tungaloy-Wendeplatte Brand: Tungaloy Facts Included angle: 90° Nose radius: 0.4 mm Relief angle: 11° Thickness: 3.18 mm Size: 09 Countersink: 40°–60° Special features PVD-coated cemented carbide grade AH6225 Single-sided chipbreaker ISO-standard square insert With cylindrical hole and one-sided countersink Suitable for stainless steel applications System components: insert, holder/boring bar, shim/clamping set, replacement screws FAQ Is this insert suitable for machining stainless steel? Yes. The AH6225 PVD-coated cemented carbide grade is designed for reliable performance in stainless-steel turning; the SPMT090304 AH6225 (SKU TUN6903310) balances a sharp cutting edge with edge stability for medium machining. Which holders will work with this ISO insert? Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness. Use holders specified for ISO square SPMT inserts and verify the 11° relief and 3.18 mm plate thickness match the holder specifications. What operations is the insert intended for? The insert is intended for external and internal turning, including facing and shoulder work, and is optimised for medium cutting conditions and variable machining scenarios. How does the single-sided chipbreaker affect performance? A single-sided chipbreaker controls chip shape and evacuation, reducing heat concentration at the cutting edge and improving machining stability for semi-finishing and medium-cut applications. Can this insert provide a good surface finish? Yes. The 0.4 mm nose radius combined with the PVD coating and stable geometry supports consistent surface integrity, particularly when cutting parameters are set for finishing or light semi-finishing passes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 AH6235 Wendeplatten - Tungaloy
Take advantage of the combination of precise geometry, a tough PVD-coated grade and secure clamping for predictive, productive turning of stainless steel and similar materials; order directly via Metav Werkzeuge or consult the team for matching holders and inserts. SPMT090304 AH6235 SPMT 090304 turning insert for stainless steel by Tungaloy The SPMT090304 AH6235 is an ISO-standard turning insert designed for external and internal turning operations, optimised for interrupted cuts and applications with increased breakout risk. PVD-coated carbide AH6235 for stainless steel ISO SPMT090304 geometry, 90° shape 0.4 mm corner radius for edge strength Cylindrical hole with one-sided countersink Precise design for reliable turning results The insert delivers a consistent cutting edge thanks to its PVD-coated carbide composition and the AH6235 tough grade, which is formulated specifically for applications in stainless steel and conditions with interruption risk. The combination of coating and substrate offers improved wear resistance and edge stability; this reduces the need for frequent index changes and contributes to a more predictable tool life. The result is a measurable improvement in process stability and fewer unplanned interruptions. Improved chip control and edge security A well-chosen single-sided chipbreaker paired with the 0.4 mm corner radius and 90° geometry ensures controlled chip formation and robust edge support during heavier cuts or interrupted machining. These geometric choices lower the likelihood of edge collapse and support a repeatable surface finish, so operators can expect reliable part quality even when machining challenging batches. The insert’s features are aimed at maintaining cutting performance and reducing secondary operations. Compatibility and secure mounting for production use As an ISO-compliant indexable insert, the component fits holders matching its form, relief angle and tolerance class; compatibility depends on the holder’s geometry, fastening method, size and thickness. The insert is supplied with a cylindrical hole and a one-sided countersink (40°–60°) to secure positive clamping and correct seating in most standard external holders and boring bars. The 3.18 mm thickness and standard size designation support repeatable clamping forces and minimise micro-movements during machining. Application focus and productivity gains Engineered for turning tasks, the grade and construction are particularly suited to machining stainless steel under intermittent conditions where fracture resistance and chip control are critical. The PVD-coated surface extends tool life and helps maintain cutting-edge integrity, which translates into reduced tool change frequency and higher uptime. Choosing this insert supports efficient workflows and contributes to predictable batch times in production environments. For reliable performance in stainless steel turning select the Tungaloy AH6235 grade — contact Metav Werkzeuge for technical matching and fast supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6903480 SKU: 6903480-Tungaloy Manufacturer SKU: TUN6903480 Model series: ISO-Drehwendeschneidplatten Name: SPMT090304 AH6235 Facts Size: 09 Thickness: 3.18 mm Corner radius: 0.4 mm Relief angle: 11° Insert angle: 90° Hole: with hole Special features PVD-coated carbide grade AH6235 One-sided chipbreaker Cylindrical hole with one-sided countersink (40°–60°) ISO-standard indexable insert Suited for turning and interrupted cuts Optimised for stainless steel FAQ Which materials is this insert suitable for? The SPMT090304 AH6235 insert is optimised for machining stainless steel and performs well in operations with interrupted cuts and increased breakout risk. Is the AH6235 grade coated and what benefit does it provide? Yes, the AH6235 grade is PVD-coated, which improves wear resistance and helps maintain edge integrity under varying cutting conditions for longer tool life. How is holder compatibility determined for this insert? Compatibility depends on the holder’s form, relief angle (11°), tolerance class, fastening method, size and thickness; secure seating is aided by the cylindrical hole with a one-sided countersink. Is this insert recommended for interrupted cuts? The tougher substrate and the AH6235 grade make this insert suitable for interrupted cutting and situations with higher breakout risk. What are the key geometric specifications of the insert? The insert has a 90° angle, 0.4 mm corner radius, 3.18 mm thickness and ISO size designation 09. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 AH725 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated AH725 grade, a 0.4 mm corner radius and ISO-compliant geometry for reliable turning results; order the insert directly via Metav Werkzeuge or consult our advisers for process matching. SPMT090304 AH725 ISO turning insert — square 90° geometry by Tungaloy SPMT090304 AH725 is a square ISO turning insert designed for external and internal turning, offering a universal, fracture-resistant grade suited to steel and stainless steels. PVD-coated AH725 universal grade Square 90° geometry for versatile turning 0.4 mm corner radius for reliable edge strength Cylindrical hole with 40°–60° countersink High-performance grade for consistent productivity The insert features a PVD coating on a cemented carbide substrate which provides a balance between wear resistance and toughness. The AH725 grade is formulated as a universal, fracture-resistant option for machining both steel and stainless steels, making it suitable where workpiece materials vary or where toolholders are smaller and process security is paramount. Optimised for stable chip flow, the grade reduces the risk of premature edge failure and supports steady cutting conditions, translating into fewer interruptions and improved component throughput. Geometry and clamping that ensure repeatable precision A square 90° geometry combined with a 0.4 mm corner radius and 11° clearance angle delivers rigid support at the cutting edge, which helps maintain dimensional accuracy and surface finish during turning. The insert’s ISO designation ensures compatibility with standard holders when form, clearance, tolerance class, clamping and thickness are matched. The centrally located cylindrical hole with a one-sided countersink (40°–60°) secures repeatable clamping and indexability, enabling quick insert changes and consistent seat contact for serial production. Practical application advice for longer tool life Designed primarily for turning operations with a single-sided chipbreaker, this grade and geometry combination performs well for general roughing and finishing when cutting parameters are chosen according to workpiece material and stability. For best results, pair the insert with a suitable external holder or boring bar and select feed and speed that favour stable chip formation—this maximises the benefits of the AH725 grade and helps avoid edge chipping. If process conditions change frequently, the universal nature of the grade reduces the need for multiple tool inventories and simplifies tool management. Discuss application matching with Metav Werkzeuge to select the ideal holder and cutting data for the SPMT090304 AH725 insert — Metav Werkzeuge provides technical consultation and fast supply. Technical data Manufacturer article number: 6856787 SKU: 6856787-Tungaloy Manufacturer SKU: TUN6856787 Model series: ISO turning inserts Material: cemented carbide Facts ISO designation: 090304 Geometry: square, 09 size, 90° Corner radius: 0.4 mm Thickness: 3.18 mm Clearance angle: 11° Hole: cylindrical hole with one-sided countersink (40°–60°) Special features Grade: AH725, PVD-coated carbide Chipbreaker: single-sided Typical application: external and internal turning Compatibility determined by form, clearance, tolerance, clamping, size and thickness FAQ What materials is this insert suitable for? The SPMT090304 AH725 Tungaloy turning insert (SKU 6856787-Tungaloy) is a universal, fracture-resistant grade intended for machining steel and stainless steels; it performs well where material types vary. Which operations are recommended for this insert? This insert is designed for external and internal turning; the square 90° geometry and single-sided chipbreaker suit both roughing and finishing when matched with appropriate cutting data. How does the 0.4 mm corner radius affect performance? A 0.4 mm corner radius increases edge strength and improves resistance to chipping, which enhances process security and contributes to a more consistent surface finish during turning operations. Is the insert compatible with standard ISO holders? Yes — the SPMT090304 format is ISO-compliant; compatibility depends on matching holder form, clearance angle, tolerance class, clamping method, size and thickness. What benefits does the PVD coating provide? The PVD coating on the AH725 grade improves wear resistance while preserving toughness, supporting stable chip formation and extended cutting life under a range of turning conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 AT9530 Wendeplatten - Tungaloy
Benefit from precise surface results and consistent tool life through the combination of the AT9530 coated cermet grade and ISO compatibility; this insert is designed for efficient finishing and light turning of steel. Order the insert via Metav Werkzeuge or consult our specialists for application-specific advice. SPMT 090304 AT9530 — Tungaloy turning insert for finishing SPMT 090304 AT9530 is an ISO-format turning insert designed for finishing and light machining on steel, combining a coated cermet grade with a small corner radius for excellent surface quality Coated cermet grade AT9530 Optimised for finishing of steel ISO SPMT090304, 0.4 mm corner radius Cylindrical hole with 40°–60° countersink Predictable productivity through controlled wear The insert delivers steady performance by pairing a coated cermet formulation with a geometry tuned for finishing. The AT9530 grade is developed to promote uniform wear patterns, which reduces the frequency of unscheduled index changes and supports predictable cycle times. With a fine cutting edge and 0.4 mm corner radius, the component is suited to operations where surface integrity and repeatability matter most. This balance of wear resistance and edge stability contributes directly to higher throughput on medium- to high-volume turning tasks. Superior surface finish in light machining For jobs that prioritise surface quality over heavy metal removal, the insert’s geometry and coating work together to produce consistently low roughness values. The single-sided chipbreaker aids chip control in finishing cuts while the insert’s small corner radius helps minimise waviness on external and internal profiles. As a result, finishing cycles often require fewer downstream operations, improving overall process efficiency and reducing handling time. Easy integration with ISO tool systems This indexable plate follows ISO form and dimensional standards, allowing straightforward use with compatible holders and boring bars. The SPMT090304 designation and square plate form simplify selection for shops running standard toolholders; compatibility is determined by form, clearance angle, tolerance class, fixing method, size and thickness. The insert’s cylindrical hole with a single-sided countersink (40°–60°) ensures secure clamping and repeatable seating in the pocket, improving stability during fine turning. Material suitability and technical advantages Manufactured from cemented carbide and finished with the AT9530 coating, the insert is optimised for steel finishing and light turning. The plate thickness of 3.18 mm and 11° clearance support stable cutting conditions while maintaining a sharp cutting edge for high-quality surfaces. The square 09 size and included angle of 90° make the insert versatile for external and internal profiles where access and rigidity are factors. The combination of substrate and coating gives a compromise between toughness and wear resistance tailored to fine turning. For ordering or application guidance on the Tungaloy AT9530 finishing insert, contact Metav Werkzeuge for a specialist consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6773742 SKU: 6773742-Tungaloy Manufacturer SKU: TUN6773742 Designation: SPMT090304 AT9530 Facts Corner radius: 0.4 mm Thickness: 3.18 mm Included angle: 90° Clearance angle: 11° Size designation: 09 Special features Coating / grade: AT9530 (coated cermet) Substrate: cemented carbide Plate form: square Chipbreaker: single-sided Hole: cylindrical hole + one-sided countersink (40°–60°) Application: turning — finishing and light machining of steel System: ISO turning indexable insert FAQ What materials is this insert intended for? The SPMT090304 AT9530 insert is optimised for finishing and light machining of steel using the AT9530 coated cermet grade. Is the insert compatible with standard ISO holders? Yes; the insert follows ISO dimensions for SPMT090304 plates and is compatible provided the holder matches form, size, thickness and fixing method. How does the 0.4 mm corner radius affect finishing? A 0.4 mm corner radius on this insert reduces surface waviness and helps achieve finer finishes on external and internal turning profiles. What clamping interface does the insert require? The insert has a cylindrical hole with a single-sided countersink (40°–60°) for secure mounting and repeatable seating in the pocket. Which feature of the AT9530 grade improves process stability? The AT9530 coated cermet promotes even wear and maintains edge integrity in finishing cuts, supporting consistent process stability Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of coated cermet performance, precise geometry and reliable clamping for consistent surface quality and extended tool life; order original Tungaloy inserts directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. SPMT090304 GT9530 indexable turning insert — coated cermet, 0.4 mm corner radius, for turning (Tungaloy) SPMT090304 GT9530 is a square ISO indexable insert designed for external and internal turning, providing high-quality finishing and improved tool life under stable machining conditions. Coated cermet grade GT9530 ISO square format 09, 3.18 mm thick 0.4 mm corner radius for fine finishing One-sided chipbreaker, with central hole Precise finishing through a wear-resistant coated cermet The coated cermet grade GT9530 provides a targeted balance between wear resistance and edge sharpness, making it particularly suited for finishing and light universal operations on steel. The microstructure of the cermet substrate and the applied coating extend effective cutting life while preserving a sharp cutting edge; this yields consistent surface quality and reduces the need for rework. For production runs where surface integrity and dimensional stability are priorities, the coated cermet composition minimises built-up edge and maintains performance over longer tool cycles. Reliable fit and stable clamping for repeatable results This ISO-design insert conforms to standard geometries so that compatibility with holders is determined by form, clearance angle, tolerance class, fastening and thickness. The 11° relief angle and the central hole with cylindrical seat plus single-sided countersink (40°–60°) ensure a secure and repeatable mounting interface. A plate thickness of 3.18 mm and the square 09 size give robust support in the pocket, while the defined 0.4 mm corner radius helps control cutting forces. Together, these characteristics improve process stability and simplify tool-change procedures for predictable component quality. Application guidance and productivity advantages in turning Designed for turning operations, the insert is applicable for both external and internal machining where a fine finish is required. Selecting the matching one-sided chipbreaker and the GT9530 grade according to workpiece material and machine stability results in optimised chip control and longer intervals between indexings. In practice, this leads to higher throughput for finished components and a lower cost per part in stable setups. The compatibility with common ISO holders and the standardised geometry also supports fast tool replacement and effective stock management. Contact Metav Werkzeuge for tailored machining recommendations and to source genuine Tungaloy SPMT090304 GT9530 indexable inserts for precision finishing. Technical data Article number: 6998346 Manufacturer SKU: TUN6998346 SKU: 6998346-Tungaloy Manufacturer: Tungaloy Model series: ISO-Drehwendeschneidplatten Core data ISO designation: SPMT090304 Plate size: 09 Plate thickness: 3.18 mm Corner radius: 0.4 mm Relief angle: 11° Included hole: with hole (cylindrical + single-sided countersink 40°–60°) Special features Coating/grade: GT9530 (coated cermet) Material: carbide Plate form: square Chipbreaker: one-sided Typical application: turning (external and internal), finishing to light universal use on steel FAQ What materials is this insert suited for? The GT9530-coated cermet insert is optimised for steel finishing operations; select the chipbreaker and machining parameters to match component material and stability. How does the GT9530 grade improve surface finish? GT9530's combination of cermet substrate and coating maintains a sharp cutting edge and resists built-up edge, which helps produce a consistent, fine surface finish during turning. Is the SPMT090304 compatible with standard ISO holders? Yes, the SPMT090304 follows ISO geometry; compatibility depends on holder form, clearance angle, tolerance class, fastening and thickness. What benefit does the 0.4 mm corner radius provide? A 0.4 mm corner radius reduces cutting stress while enabling precise finishing, helping to achieve dimensional accuracy and good surface integrity. Can this insert be used for heavy roughing? This insert is specified as a wear-resistant finishing to light universal grade; for heavy roughing, a different geometrical form or a tougher grade should be selected. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 NS9530 Wendeplatten - Tungaloy
Benefit from an ISO‑standard square turning insert with a sharp uncoated NS9530 cermet grade, a 0.4 mm corner radius and 11° relief for superior surface finish and low cutting forces; order directly via Metav Werkzeuge or consult our specialists for application support. SPMT 090304 NS9530 turning insert by Tungaloy — ISO square 90° 0.4 mm A SPMT090304 NS9530 ISO turning insert designed for precision external and internal turning, delivering a finishing cermet grade optimised for steel components. ISO‑standard geometry for wide holder compatibility Uncoated cermet NS9530 for high surface finish 0.4 mm corner radius for profile accuracy Cylindrical hole with countersink for secure clamping Superior finish and reduced secondary work The uncoated NS9530 cermet grade provides a sharp cutting edge and low cutting forces, which directly benefits finishing operations on steel. In practice this means fewer passes to reach target roughness, reduced need for secondary grinding or polishing and consistently improved surface integrity. The finishing character of this grade is particularly effective in continuous cutting conditions and at small depths of cut, so operators can expect reliable economics through lower rework and faster cycle times. Faster setup and verified ISO compatibility Built to ISO standards, the insert’s square form and defined dimensions ensure straightforward matching with a wide range of external holders and boring bars. Critical parameters that determine compatibility—form, relief angle, tolerance class, fastening, size and thickness—are standardised to simplify selection and reduce setup time. The insert is 3.18 mm thick, size 09, with a 90° geometry and 11° relief; the mounting hole is cylindrical with a single‑side countersink (40°–60°), enabling secure clamping and repeatable positioning. Productive machining with controlled chip formation The one‑sided chipbreaker and the insert’s geometry support stable chip control during turning, contributing to predictable tool life and consistent part quality. Designed for both external and internal turning, this insert is suited to applications where a fine finished surface is required and where machining stability is present. The ISPMT series system approach—insert, matching external holder or boring bar, plus the appropriate clamp and screws—enables a robust setup that keeps process interruptions to a minimum and helps maintain high throughputs. For precision finishing in turning operations, contact Metav Werkzeuge for the SPMT090304 NS9530 insert and tailored application advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6998622 SKU: 6998622-Tungaloy Manufacturer SKU: TUN6998622 Manufacturer: Tungaloy Model series: ISO turning inserts Material: cemented carbide Grade: NS9530 (uncoated cermet) Core specifications ISO designation: SPMT090304 Insert size: 09 Shape: square (90°) Corner radius: 0.4 mm Thickness: 3.18 mm Relief angle: 11° Hole: with cylindrical hole + single‑side countersink (40°–60°) Special features One-sided chipbreaker For external and internal turning Suitable for continuous cuts and small depths Compatibility via form, relief, tolerance, fastening, size, thickness System components: holder, clamping set, replacement screws FAQ Which materials is this insert best suited for? The NS9530 uncoated cermet grade is a finishing grade optimised for steel, delivering low cutting forces and excellent surface finish when used in continuous turning operations. Can the SPMT090304 be used for internal turning? Yes, the square geometry and chipbreaker support both external and internal turning applications when paired with an appropriate boring bar or internal holder. What mounting features ensure reliable clamping? The insert features a cylindrical hole with a single‑side countersink (40°–60°), designed to provide secure and repeatable clamping in standard ISO clamping systems. How does the corner radius affect profile accuracy? The 0.4 mm corner radius provides a balance between edge strength and profile definition, improving dimensional accuracy for small contours while maintaining a sharp cutting edge for finishing. Is the insert suitable for interrupted cuts? This finishing grade is primarily intended for continuous cuts and small depths of cut; interrupted or heavy roughing applications may require a more robust grade. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of a finishing-grade uncoated cermet and an ISO-format plate for reliable surface quality and low cutting forces; the sharp cutting edge and small corner radius reduce rework and enhance productivity. Order the SPMT090304 NS9530 insert directly via Metav Werkzeuge or ask our consultants if needed. SPMT090304 NS9530 – ISO turning insert, uncoated cermet (Tungaloy) The SPMT090304 NS9530 is an ISO-format turning insert designed for external and internal finishing on steel, offering a sharp cutting edge and low cutting forces for continuous cuts. Finishing-grade uncoated cermet NS9530 Low cutting forces for continuous cuts 0.4 mm corner radius for fine detail Square ISO plate with cylindrical hole and countersink Improved finishing with lower machining forces The finishing-grade NS9530 uncoated cermet is optimised for low cutting forces and a sharp cutting edge, which together produce a consistently high surface finish on steel components. The combination of a small 0.4 mm corner radius and a precise cutting geometry reduces the need for secondary grinding or polishing, lowering cycle times and overall manufacturing costs. This makes the insert particularly suitable where continuous cuts and small depths of cut are routine. Designed for secure clamping and straightforward integration As an ISO-format plate, the insert fits standard holders when form, relief angle, tolerance class, fastening method, size and thickness are matched. The plate is square (size 09) with a 3.18 mm plate thickness, a 11° relief angle and a central hole with a cylindrical bore plus a one-sided countersink (40°–60°), enabling stable seating and repeatable clamping. The 90° cutting angle and standardised dimensions simplify tool inventory and reduce setup time when changing tools within a production line. Material range and reliable process performance The insert combines a carbide body and an uncoated cermet cutting material, giving a balance of wear resistance and edge acuity for finishing operations on steel. The single-sided chipbreaker is tailored for chip control in stable turning conditions, improving surface integrity and process repeatability. Typical uses include external and internal turning where a fine finish and gentle cutting action are required, delivering predictable results and reduced scrap rates. Contact Metav Werkzeuge for tailored advice on Tungaloy finishing inserts and rapid supply; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6998504 SKU: 6998504-Tungaloy Manufacturer SKU: TUN6998504 Model series: ISO-Drehwendeschneidplatten Designation: SPMT090304 Manufacturer: Tungaloy Material: carbide Cutting material: uncoated cermet NS9530 Facts Thickness: 3.18 mm Corner radius: 0.4 mm Relief angle: 11° Size: 09 Insert angle: 90° Manufacturer article number: 6998504 Special features Square plate with cylindrical hole and one-sided countersink (40°–60°) Single-sided chipbreaker ISO-format insert for external and internal turning Finishing grade for steel, optimised for continuous cuts and small depths Compatibility depends on holder form, relief angle, tolerance class and fastening FAQ What applications suit this finishing insert best? The SPMT090304 NS9530 insert by Tungaloy is tailored for external and internal turning on steel where a high surface finish and low cutting forces are required, especially for continuous cuts and small depths. Is the insert compatible with standard ISO holders? Compatibility is determined by holder form, relief angle, tolerance class, fastening, size and thickness; the SPMT090304 follows ISO dimensions for straightforward integration with matching holders. Which materials can be machined with this grade? The uncoated cermet NS9530 in this insert is optimised for steel finishing; the insert body is carbide, supporting stable cutting performance for the stated application. How does the chip control perform? The single-sided chipbreaker is designed for improved chip control in stable turning operations, supporting consistent surface quality and reduced risk of chip-related interruptions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precise finishing performance, consistent holder compatibility and the low cutting forces of the NS9530 cermet grade for smoother turning operations. Order the SPMT090304 NS9530 indexable insert directly via Metav Werkzeuge or ask the consultants for tailored application advice. SPMT 090304 NS9530 — ISO turning insert for finishing — Tungaloy A SPMT090304 NS9530 indexable insert engineered for finishing steel during external and internal turning, offering a sharp edge and stable surface results. ISO SPMT 090304 format for standard holders Uncoated cermet NS9530 for fine finishing Sharp edge with low cutting forces Square insert, 0.4 mm corner radius, 11° relief angle Higher surface quality with reduced cutting effort The combination of an uncoated cermet grade and a deliberately sharp cutting geometry delivers low cutting forces and an improved surface appearance in finishing cuts. The NS9530 composition is optimised for continuous cutting and small depths of cut, which reduces vibration risks and helps maintain consistent tolerances. Operators benefit from a predictable contact condition between tool and workpiece, enabling higher first-pass quality and fewer secondary operations. Reliable fit into ISO turning systems Designed to ISO plate dimensions, the insert features a square form with a central hole and a cylindrical hole plus one-sided countersink (40°–60°) for stable clamping. Compatibility with a given holder is determined by the insert form, relief angle, tolerance class, fastening style, size and thickness; the standardised SPMT format simplifies selection and replacement in established toolholders. This leads to faster changeovers and predictable set-up times on the shop floor. Why an uncoated cermet grade suits finishing steel A cermet is a ceramic–metal composite that retains a keen edge and resists cratering during fine finishing. The NS9530 grade used here prioritises edge sharpness and low friction over heavy-duty wear resistance, making it particularly suitable when a superior surface finish is the main objective. The insert’s geometry further supports stable chip flow with the single-sided chipbreaker, helping to avoid edge build-up when machining steels under continuous cut conditions. Practical recommendations for consistent results Selection of chipbreaker and grade should match material, machining type and machine-tool stability. For turning steel with small feeds and light depths of cut, the combination of the NS9530 grade and the fine corner radius ensures excellent final surfaces. Use the correct underlay, clamping set and replacement screws when assembling the system, and ensure holders accept the SPMT 090304 dimensions and the 11° relief angle to maintain seating accuracy and repeatable performance. Contact Metav Werkzeuge for application support on Tungaloy finishing inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 for specific recommendations and availability Technical data Article number: 6998502 SKU: 6998502-Tungaloy Manufacturer SKU: TUN6998502 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall WPL designation: SPMT090304 Grade: NS9530 Facts Included angle: 90° Corner radius: 0.4 mm Relief angle: 11° Plate thickness: 3.18 mm Plate size: 09 Special features Uncoated cermet grade NS9530 Single-sided chipbreaker Square plate form With cylindrical hole + one-sided countersink (40°–60°) Application: turning (finishing steel) Compatibility determined by form, relief angle, tolerance class, fastening, size and thickness FAQ Which operations are best suited to this insert? The SPMT090304 NS9530 insert is intended for finishing operations in turning, suitable for both external and internal turning where a sharp edge and fine surface are required. Is the insert compatible with standard ISO SPMT holders? Yes, the insert follows the ISO SPMT 090304 format; compatibility depends on holder acceptance of form, relief angle, tolerance class, fastening, size and thickness. What materials are recommended for this grade? The NS9530 uncoated cermet is optimised for steel finishing under continuous cuts and small depths of cut, offering low cutting forces and excellent surface quality. How should the insert be clamped? Use a matching underlay or clamping set with the correct replacement screws; the central hole with cylindrical bore and one-sided countersink ensures secure, repeatable seating. How does the 0.4 mm corner radius affect results? A 0.4 mm radius balances edge strength and finishing capability, aiding in achieving consistent surface quality while maintaining a sharp cutting edge. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of reliable CVD-coated carbide, ISO compatibility and a compact 0.4 mm corner radius to achieve consistent chip formation and stable cutting in cast-iron turning operations. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. SPMT090304 T5115 Turning Insert (ISO 090304) – Square 09, 0.4 mm Corner Radius (Tungaloy) The SPMT090304 T5115 is an ISO‑normed square turning insert intended for external and internal turning, engineered as a universal grade for cast iron with a one‑sided chipbreaker and a cylindrical locating hole with a single‑side countersink. ISO square insert SPMT090304, 0.4 radius CVD-coated carbide grade T5115 for cast iron One-sided chipbreaker with 11° relief angle Consistent cutting performance for cast-iron turning The indexable plate delivers reliable cutting behaviour thanks to the CVD-coated carbide composition of grade T5115, which balances wear resistance and edge stability for cast-iron machining. The engineered coating improves flank wear resistance and reduces built-up edge formation, so the tool life is extended under typical turning loads. For production environments, the result is fewer insert changes and more predictable batch yields, which supports efficient planning and lower machining costs. System compatibility and secure clamping for reproducible results Designed as part of the ISO turning insert system, the square 09 format and the cylindrical hole with a one-sided countersink (40°–60°) ensure secure location in compatible holders. The insert’s geometry—including the 11° relief angle and 3.18 mm thickness—matches standard ISO interfaces, enabling straightforward integration into existing toolholders and tool posts. This compatibility reduces setup time and simplifies inventory management for workshops and production lines. Productivity and economical operation through optimised chip control The insert’s one‑sided chipbreaker is tuned for chip control in cast iron, producing short, consistent chips that evacuate reliably even in interrupted cuts. Combined with the modest 0.4 mm corner radius, the geometry supports stable cutting with reduced vibration and better surface integrity. The net effect is higher productivity: stable edge life plus improved chip flow reduces downtime for clearing and tool changes, delivering measurable process gains across repeating operations. Practical handling and application guidance The square form factor allows multiple indexings per insert, improving utilisation and cost efficiency in serial turning. The ISO designation and detailed dimensions mean selection of an appropriate holder should consider form, clearance angle, tolerance class and fastening method to guarantee correct seat and clamping. For finishing or semi‑roughing passes on cast iron, the grade's balanced properties permit flexible feed and depth settings while preserving edge condition; for unfamiliar applications, a brief trial cut is recommended to confirm ideal parameters. Contact Metav Werkzeuge for availability and application advice on the SPMT090304 T5115 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss holder compatibility and batch requirements Technical data Article number: 6864683 Manufacturer SKU: TUN6864683 Label: SPMT090304 T5115 Tungaloy‑insert Facts Corner radius: 0.4 mm Relief angle: 11° Thickness: 3.18 mm Size designation: 09 Angle: 90° Special features CVD-coated carbide (T5115) Universal grade for cast iron One-sided chipbreaker Square insert, ISO series With cylindrical hole and one-sided countersink (40°–60°) FAQ Which materials is this insert designed for? The SPMT090304 T5115 insert is formulated as a universal grade for cast iron, offering a balance of wear resistance and edge stability for external and internal turning of grey and nodular cast irons. How is the insert secured in the toolholder? The insert locates via a cylindrical hole with a single‑side countersink and is clamped in ISO‑compatible holders; correct holder form, clearance angle and fastening ensure reproducible seating for the SPMT090304. What advantages does the T5115 coating provide? The CVD coating on the T5115 grade increases flank wear resistance and helps prevent built‑up edge on cast iron, improving insert life and part quality under typical turning conditions. Can the square insert be indexed multiple times? Yes, the square geometry permits several indexings per insert, which increases utilisation and reduces tooling costs when machining repetitive features. Is the insert suitable for finishing passes? The modest 0.4 mm corner radius and balanced grade make the insert suitable for both finishing and light to moderate roughing on cast iron, depending on cutting parameters and machine stability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 T6215 Wendeplatten - Tungaloy
Benefit from the combination of CVD-coated carbide grade T6215 for reliable edge life and controlled chip formation, plus a compact 90° square geometry that fits standard ISO holders; order the SPMT090304 T6215 insert directly via Metav Werkzeuge or ask our consultants if needed. SPMT090304 T6215 ISO 90° square turning insert by Tungaloy — for stainless steel turning The SPMT090304 T6215 is an ISO-standard 90° square indexable insert designed for external and internal turning of stainless steel under stable to slightly interrupted cutting conditions. CVD-coated T6215 for stainless steels ISO SPMT090304 90° square geometry 0.4 mm nose radius for light profiling Cylindrical hole with single-side countersink (40°–60°) Consistent edge life and material suitability for stainless steel turning The CVD-coated carbide grade T6215 offers wear resistance tailored to the demands of machining stainless steel, making the insert suitable for sustained production runs where flank and crater wear must be controlled. The coating and substrate combination reduces adhesive wear and helps maintain cutting-edge integrity during turning operations, which translates into longer tool life and predictable regrinding intervals. This results in a more efficient process with fewer unscheduled tool changes and a steadier component quality. Designed for secure mounting and ISO compatibility Compatibility is determined by form, relief angle, tolerance class, fastening method, size and thickness; the insert conforms to ISO dimensions and is therefore suitable for many standard external tool holders and boring bars. The system build comprises the ISO insert, a matching outer holder or boring bar, a shim/clamp set and replacement screws. The 90° square shape and 3.18 mm thickness deliver mechanical stability in the clamped joint, while the cylindrical hole with a single-side countersink (40°–60°) ensures proper seating and repeatable positioning in the cutter body. Controlled chip formation and fine-surface capability With a single-sided chipbreaker and a modest 0.4 mm nose radius, the insert balances surface finish and tool robustness for common turning applications. The chipformer and grade selection support chip control tailored to the workpiece material and machining parameters, reducing the risk of built-up edge during stainless-steel turning and improving process reliability. In practice, this means fewer interruptions, consistent surface quality and a reduced need for secondary finishing operations. Contact Metav Werkzeuge for application advice on the Tungaloy SPMT090304 T6215 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt guidance and supply options. Technical Data Article number: 6903108 Manufacturer SKU: TUN6903108 SKU: 6903108-Tungaloy Model series: ISO turning indexable inserts Article designation: SPMT090304 T6215 Tungaloy insert Core dimensions Nose radius: 0.4 mm Plate thickness: 3.18 mm Size code: 09 Included angle: 90° Relief (free) angle: 11° Hole style: cylindrical hole + single-side countersink (40°–60°) Features & applications Coating: CVD-coated Material: carbide Chipbreaker: single-sided Typical application: external and internal turning Suited for machining stainless steels under stable to slightly interrupted conditions ISO-compatible insert for use with matching holder, shim/clamp set and replacement screws FAQ What materials is this insert intended for? The SPMT090304 T6215 insert is designed primarily for machining stainless steel under stable to slightly interrupted cutting conditions and is optimised through the CVD-coated T6215 grade for improved wear resistance. Which holders are compatible with this ISO insert? Compatibility depends on the holder form, relief angle, tolerance class, fastening and size; the SPMT090304 conforms to ISO dimensions and is compatible with standard 90° square external holders and boring bars when matched with the correct shim/clamp set. How does the chipbreaker affect performance? The single-sided chipbreaker on this insert promotes consistent chip formation for many turning tasks, improving process reliability and contributing to a better surface finish when paired with appropriate cutting data for stainless steel. What mounting features ensure repeatable positioning? The insert has a cylindrical hole with a single-side countersink (40°–60°) that ensures secure seating and repeatable positioning in the cutter body; the plate thickness of 3.18 mm adds stiffness in the clamped joint. What is the manufacturer SKU and article number for ordering? The manufacturer SKU is TUN6903108 and the article number is 6903108; the product is listed as SPMT090304 T6215 Tungaloy insert with SKU 6903108-Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
SPMT 090304 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD‑coated T9215 wear resistance and precise ISO compatibility for steady productivity in medium steel turning; order directly via Metav Werkzeuge or consult our technical advisers for application-specific configuration. SPMT090304 T9215 ISO turning insert for Drehen by Tungaloy SPMT090304 T9215 is an ISO‑standard square turning insert engineered for external and internal turning operations in medium steel machining. CVD‑coated carbide T9215 for steel machining ISO‑standard square insert, size 09 Single‑sided chipbreaker for consistent chip control 11° clearance angle and 0.4 mm corner radius Reliable productivity for medium steel turning The CVD‑coated grade T9215 combines high wear resistance with fracture toughness to sustain continuous to lightly interrupted cuts, making it ideal for steady production runs where tool life and process stability matter. The coating reduces abrasion on the cutting edge, which translates into longer tool life and fewer changeovers. With a predictable edge behaviour, the insert supports consistent part quality and reduces scrap rates when machining medium‑strength steel alloys. Seamless integration into ISO tool systems Designed as an ISO standard insert, the plate fits common square holders when matched for form, clearance, tolerance class, fastening and thickness. The insert hole with cylindrical bore and single‑side countersink (40°–60°) enables secure clamping and rapid indexing, while the 3.18 mm plate thickness contributes to cutting edge rigidity and vibration dampening. The system structure requires an appropriate holder, shim and clamping screw; selecting matching components ensures repeatable setup and short tool change times. Predictable chip control and economic machining The single‑sided chipbreaker geometry is tuned for controlled chip formation in turning, helping evacuate chips reliably and maintain a steady surface finish. The combination of 0.4 mm corner radius and 11° clearance angle balances edge strength with finishing capability, so each cut can achieve dimensional accuracy without sacrificing productivity. For processes prioritising uptime and consistent results, this insert presents a cost‑effective option by lowering tooling consumption per part and stabilising cycle times. For procurement or application advice on Tungaloy turning solutions, contact Metav Werkzeuge for order and technical consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 6774066 SKU: 6774066-Tungaloy Manufacturer SKU: TUN6774066 Model series: ISO turning indexable inserts Material: Carbide (Hartmetall) Designation: SPMT090304 Core specifications Insert size: 09 Plate thickness: 3.18 mm Corner radius: 0.4 mm Clearance angle: 11° Included angle: 90° Countersink angle: 40°–60° Design & features CVD‑coated carbide grade T9215 Single‑sided chipbreaker Square insert form with cylindrical hole and one‑side countersink ISO‑standard geometry for compatibility with matching holders Suited for external and internal turning (Drehen) Recommended use: mid‑range steel machining; continuous to slightly interrupted cuts FAQ What materials is this insert suitable for? The SPMT090304 T9215 insert by Tungaloy is specified for medium steel machining, where the CVD‑coated carbide grade T9215 balances wear resistance and toughness. How does the chipbreaker affect performance? The single‑sided chipbreaker on the SPMT090304 T9215 supports consistent chip control, improving evacuation and surface finish during turning operations with the recommended cutting parameters. What are the key geometry features to check before mounting? Confirm matching holder form, tolerance class, fastening method, insert thickness (3.18 mm) and the 11° clearance angle to ensure correct seating and clamp fit for the SPMT090304 Tungaloy insert. Can the insert handle interrupted cuts? The T9215 grade in this insert is engineered for continuous to lightly interrupted cuts, offering a compromise between wear resistance and edge fracture strength suitable for many production turning tasks. Is the insert indexable and easy to replace in the holder? Yes, the ISO‑standard SPMT090304 is indexable; the cylindrical hole with a single‑side countersink allows secure clamping and straightforward indexing in compatible holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
SPMT 090304 T9225 Wendeplatten - Tungaloy
Take advantage of a robust, CVD‑coated carbide grade that delivers consistent performance in medium to heavy steel turning; compatible with ISO holders and supplied with a secure central hole and countersink — order the insert directly via Metav Werkzeuge or consult the team for application advice. SPMT090304 T9225 SPMT Turning Insert by Tungaloy — CVD‑coated carbide, 11° relief, 0.4 mm radius The SPMT090304 T9225 Tungaloy turning insert is an ISO‑format, square indexable insert engineered for external and internal turning in steel; the universal T9225 grade provides toughness for varying entry conditions and lightly interrupted cuts. CVD‑coated carbide grade T9225 Universal grade for medium to heavy steel ISO SPMT090304 format with 11° relief 0.4 mm corner radius, hole and countersink Reliable cutting performance for mixed turning conditions The combination of a CVD‑coated carbide body and the T9225 grade results in a wear‑resistant yet tough cutting edge designed for medium to heavy steel machining. This balance improves tool life under fluctuating engagement and mildly interrupted cuts, reducing the need for frequent indexing. The square plate format and specified 11° relief help maintain a stable cutting geometry in matched holders, which translates into predictable chip flow and consistent dimensional results on turned parts. Practical system compatibility and setup benefits The insert is built to ISO standards, ensuring fitment with compatible external holders, boring bars, shims and clamping kits when the form, relief angle, tolerance class, fastening, size and thickness match. The central cylindrical hole with one‑sided countersink (40°–60°) simplifies secure fastening and repeatable seating, while the plate thickness of 3.18 mm supports rigidity in assembly. Using a correctly matched clamping set and replacement screws helps to exploit the insert’s stability and maintain surface finish requirements with minimal set‑up time. Efficiency gains and application guidance for shop floors Selecting this universal grade insert supports productive turning workflows: the robust universal grade reduces the number of tool changes across a range of steel alloys, and the 0.4 mm corner radius offers a compromise between edge strength and profile detail. Where higher toughness is required, the grade tolerates slight interruptions without chipping, lowering scrap risk. For optimal results, pair the insert with a suitable ISO external holder and choose feeds and speeds that reflect material properties and machine rigidity to maximise tool life and process reliability. For professional specification or procurement of the Tungaloy SPMT090304 T9225 indexable insert, contact Metav Werkzeuge for tailored advice and availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6781075 SKU: 6781075-Tungaloy Manufacturer SKU: TUN6781075 Manufacturer article number: 6781075 ISO designation: SPMT090304 Facts Plate size: 09 Plate thickness: 3.18 mm Corner radius: 0.4 mm Relief angle: 11° Included hole style: cylindrical hole with 40°–60° one‑sided countersink Plate shape: square Included angle: 90° Special features Coating: CVD‑coated carbide Grade: T9225 (robust universal grade for steel) Chipbreaker: single‑sided chipbreaker Application: external and internal turning of steel System requirements: compatible with ISO holders, shims and clamping sets; compatibility determined by form, relief angle, tolerance, fastening, size and thickness FAQ What materials is this insert suited for? The Tungaloy SPMT090304 T9225 indexable insert is optimised for medium to heavy steel machining and tolerates varying engagement and light interruptions. Can the insert be used for internal and external turning? Yes; the ISO‑format plate and stable geometry make the insert suitable for both external and internal turning applications when paired with the appropriate holder and clamping components. What fastening arrangement does the plate require? The plate uses a central cylindrical hole with a one‑sided countersink (40°–60°) for secure fastening in compatible holders; proper shims and screws ensure repeatable seating. How does the T9225 grade influence tool life? The T9225 CVD‑coated carbide grade combines wear resistance with enhanced toughness, providing longer life under mixed cutting conditions and reducing edge failure risk in interrupted cuts. Is the insert compliant with ISO dimensions? Yes; the insert follows the ISO designation SPMT090304 and is intended for holders and systems that accept this format. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com