VCGT110304-FM2 WSM01 WSM01 Wendeplatten - Walter Tools

The combination of the Tiger‑tec Silver series and the WSM01 grade delivers stable cutting edges and reliable chip control for demanding stainless and heat‑resistant superalloy turning; the optimized FM2 chipbreaker and the rhombic 35° geometry support consistent surface quality and extended tool life. Order the insert directly via Metav Werkzeuge or consult the team for application-specific advice.

VCGT110304-FM2 WSM01 — Indexable turning insert, Tiger‑tec Silver, FM2 chipbreaker (Walter Tools)

VCGT110304-FM2 WSM01 is a rhombic 35° indexable turning insert designed for machining stainless steels and heat‑resistant superalloys with an emphasis on process security and tool life

• Tiger‑tec Silver coating for longer tool life
• Optimised FM2 chipbreaker for secure chip control
• Rhombic 35° geometry for versatile turning
• Suitable for stainless steel and superalloys

Consistent performance for difficult‑to‑cut alloys

The Walter Tools insert from the Tiger‑tec Silver series and grade WSM01 combines coating technology and a carbide substrate to address the typical challenges of stainless steel and superalloys: edge build‑up, heat concentration and poor chip evacuation. The FM2 chipbreaker stabilises chip formation and reduces the risk of built‑up edge, which in turn improves surface finish and reduces rework. For shop floors that demand repeatable results, this indexable insert supports a steady production flow and predictable tool change intervals, improving overall uptime and cost efficiency.

Geometry and dimensions that support versatile turning

The insert’s rhombic 35° form and 7° relief angle enable flexible tool positioning and good entry behaviour in a wide range of turning operations. A 0.4 mm corner radius balances edge strength and the ability to produce acceptable surface roughness in finishing to medium‑depth cuts. These dimensional choices make the insert suitable for facing, light turning and profile work in tougher materials, where consistent cutting conditions and reduced vibration are essential for machining quality components.

Design features that simplify process implementation

The FM2 chipbreaker is engineered to manage chips from ductile, heat‑sensitive materials, promoting short, controllable chips instead of long, tangled swarf. Combined with the WSM01 coated carbide grade, this reduces edge wear and thermal loading at the cutting zone. For production planners, the result is improved tool life and fewer interruptions for tool inspection or premature regrinding. The insert’s standard indexable format also permits quick replacement and consistent orientation, which eases set‑up and reduces operator variability.

Application guidance and material compatibility

This insert is intended for machining stainless steel (ISO group M) and heat‑resistant superalloys and titanium (ISO group S). Selection of cutting data should reflect the material’s heat conductivity and strength at temperature: lower cutting speeds and higher feed rates are often recommended for nickel‑based superalloys, while optimised coolant strategy and stable clamping are critical for achieving the best life from the WSM01 grade. When paired with appropriate toolholders and cutting parameters, the insert supports a productive balance between material removal rate and surface integrity.

For tailored recommendations and stock availability of the Walter Tools VCGT110304-FM2 WSM01 insert, please contact Metav Werkzeuge — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for specialist advice and application support

Technical data

• Article number: VCGT110304-FM2-WSM01-WALTER
• Designation: VCGT110304-FM2
• ISO designation: VCGT110304-FM2 WSM01
• Series: Tiger‑tec Silver
• Manufacturer: Walter Tools

Facts

• Relief angle: 7°
• Corner radius: 0.4 mm
• Plate size: 11
• Thickness code: 03
• Tolerance class: G

Features

• Chipbreaker: FM2
• Grade: WSM01
• Plate form: Rhombus 35°
• Suitable materials: stainless steel (M), heat‑resistant superalloys / titanium (S)
• Execution: T

FAQ

What materials is this insert suited for?
The VCGT110304‑FM2 WSM01 insert is suitable for stainless steel (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), where the WSM01 grade and FM2 chipbreaker provide stable cutting behaviour.

How does the FM2 chipbreaker improve machining?
The FM2 chipbreaker promotes secure chip control and short chip forms when machining ductile or heat‑sensitive alloys, helping to reduce built‑up edge and improving surface finish with this Walter Tools insert.

Which geometric features support versatile use?
The rhombic 35° geometry together with a 7° relief angle and 0.4 mm corner radius offer a compromise between edge strength and finishing capability, making the insert adaptable to facing and light to medium turning tasks.

Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen

Protected trademarks and trade names remain the property of their respective owners. Mention of brand names such as Walter Tools is for explanation only and does not imply any affiliation. The offered article is an original, factory‑new product of the manufacturer.