90° 450 N Horizontal Clamp, Zinc Plated, 520 N Holding Force - Kukamet

Take advantage of the combination of galvanised durability, compact design and reliable holding force for consistent production results; order the clamp directly via Metav Werkzeuge or ask our consultants if needed.

Horizontal toggle clamp 111 – galvanised horizontal foot, 520 N holding force (Kukamet)

Horizontal toggle clamp 111 is a compact horizontal clamp intended for repeatable workholding in assembly jigs and light-duty fixtures, offering corrosion-resistant construction and dependable clamping performance.

• Galvanised corrosion protection
• 520 N holding force
• Horizontal foot for secure mounting
• M4x25 pressure spindle for fine adjustment

Consistent clamping for repetitive production

The toggle mechanism delivers a reproducible clamping action that reduces setup variance and shortens cycle times. With a specified holding force of 520 N and a maximum clamping force of 450 N, the unit provides measurable performance that supports predictable process control. The compact construction and defined 90° operating angle allow integration into small fixtures without compromising access or visibility, while the low mass contributes to reduced inertia in automated assemblies.

Simple mounting and precise adjustment for jig builders

Equipped with a horizontal foot, the clamp mounts easily to flat plates and bench fixtures, creating a low-profile workholding point that keeps components accessible. The M4x25 pressure spindle permits fine adjustment of contact pressure and compensates for part tolerances, translating into fewer rejected parts and less rework. The design is optimised for quick fixture changes and repeatable positioning, which benefits production lines that require frequent part turnover or short runs.

Robust finish and low-maintenance operation

A galvanised surface treatment safeguards against corrosion in typical workshop environments, extending service life and reducing maintenance cycles. The clamp is supplied without an arm fitted, keeping the mechanism straightforward and reliable for general-purpose clamping tasks. The lightweight construction (approx. 0.042 kg) and lever-style actuation support ergonomic handling during installation and manual operation, while the simple geometry minimises wear points over long-term use.

Contact Metav Werkzeuge for availability, specification support or a tailored quotation — Metav Werkzeuge can supply the Kukamet Horizontal toggle clamp 111 directly from Emmerich (info@metav-werkzeuge.com | +49 2822 7131930)

Technical data

• Article number: 111-0
• GTIN: 8680731500004
• Manufacturer: Kukamet

Facts

• Max clamping force: 450 N
• Max holding force: 520 N
• Weight: 0.042 kg
• Angle: 90°
• Spindle: M4x25

Special features

• Galvanised finish
• Horizontal foot mounting
• No arm fitted
• Lever-style clamp (horizontal)

FAQ

What is the primary use of this clamp?
The Kukamet Horizontal toggle clamp 111 is intended for repeatable workholding in assembly jigs and light fixtures where a reliable horizontal clamping action is required.

Can the clamp be adjusted to compensate for part tolerances?
Yes, the M4x25 pressure spindle on the Horizontal toggle clamp 111 allows fine adjustment of the contact point to account for varying part thicknesses.

Is the clamp suitable for outdoor or humid workshop environments?
The galvanised finish on the Horizontal toggle clamp 111 provides corrosion resistance suitable for typical workshop and sheltered outdoor conditions.

What mounting method does the clamp use?
The clamp uses a horizontal foot for secure mounting to flat surfaces and fixture plates.

How much holding force does the clamp provide?
The clamp offers a maximum holding force of 520 N and a clamping force up to 450 N, giving measurable performance for light-duty applications.

Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com