40mm Closure Plug Z2 Form A20 D83, DIN 69880 VDI40 - TECWERK

Take advantage of precise fit and reliable protection with the combination of Form Z2 geometry and VDI40 compatibility for reduced downtime and cleaner toolholders. Order the sealing plug directly via Metav Werkzeuge or consult the Metav specialists for suitability checks.

Sealing plug Z2 (DIN 69880) for VDI40 toolholders — TECWERK

The Sealing plug Z2 DIN 69880 VDI40 TECWERK is a closure component for VDI40 toolholders, designed to protect internal bores and interfaces during storage, transport and maintenance.

• VDI40 standard compatibility
• Form Z2 geometry for precise fit
• d1 40 mm nominal bore
• Protects toolholder internals

Prevents contamination and reduces maintenance intervals

The primary purpose of this sealing component is to prevent contamination of the toolholder interior and interfaces, thereby reducing the risk of corrosion and particle ingress. By closing off the spindle-side bore with a precisely formed plug, routine cleaning cycles become less frequent and unscheduled maintenance is lower. The combination of standard conformity and defined dimensions ensures predictable performance in workshop workflows, delivering measurable time savings and improved uptime for production-critical tooling systems.

Ensures reliable fit across VDI40 systems

Compatibility with the VDI40 interface and compliance with DIN 69880 allow secure placement in standardised toolholders. The Form Z2 profile provides a tight seating geometry while the nominal bore d1: 40 mm and outer diameter D: 83 mm ensure the part aligns with common VDI40 receptacles. This technical conformity simplifies inventory management: one recognised component type can serve multiple holders. Clear dimensional data supports quick verification during goods receipt and fit checks on the shop floor, reducing assembly time and minimising installation errors.

Simplifies storage and handling while protecting investment

As a simple yet effective accessory, the plug offers a practical way to protect cutting tools and holders during storage and transport. Using standardised closure components helps maintain toolholder surfaces and sealing faces, which preserves concentricity and prolongs the service life of precision interfaces. For operations seeking consistent handling procedures, these plugs enable orderly storage routines and quicker setup at changeovers. The product’s measured design supports both experienced technicians and those newer to toolroom practice, delivering confidence in handling and preservation.

For compatibility verification or to arrange supply of the TECWERK VDI40 sealing plug, contact Metav Werkzeuge in Emmerich for tailored advice and order processing via info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: 2000833697NW
• Label: Verschlussstopfen Z2 DIN 69880 VDI40 STA TECWERK
• Manufacturer: TECWERK
• Product type: Sealing plug
• Packaging unit: 1
• UID: 2000833697NW

Dimensions & core data

• d1: 40 mm
• A: 20 mm
• D: 83 mm
• Form: Z2
• Standard: DIN 69880 / VDI40

Special features

• Form Z2 geometry
• VDI40 interface compatibility
• Designed for closure and protection of toolholder bores
• Suitable for storage and transport protection

FAQ

What does Form Z2 indicate for this sealing plug?
Form Z2 describes the plug’s seating geometry and contour; it is the specified profile that ensures a secure, repeatable fit in compatible VDI40 receptacles.

Is the plug compatible with all VDI40 toolholders?
Compatibility is intended for VDI40 interfaces that conform to DIN 69880 dimensions; verification against the specific holder drawing is recommended because variations in holder design can exist.

What are the main dimensions to check before fitting?
Key dimensions are the bore diameter d1: 40 mm, the axial length A: 20 mm and the outer diameter D: 83 mm; these determine seating depth and clearance.

Is the material of the sealing plug specified?
The product listing does not specify the material; material information is not provided in the available product data.

Can the plug be used during machining operations?
This plug is designed for protection during storage, transport and handling; it is not intended as a component for use during active cutting or high-speed machining.

TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund