58mm Sheet Countersink Drill HSS-Co 2-Flute 20° Chamfer, 6mm Shank - TECWERK

Take advantage of the combination of HSS‑Co cutting material, a 20° countersink geometry and a secure 6 mm shank for consistent, burr‑reduced holes in thin materials; order the tool directly via Metav Werkzeuge or consult the technical team for application advice.

TECWERK sheet‑metal peel drill (3–14 mm) – HSS‑Co, 58 mm overall length

The TECWERK sheet‑metal peel drill 3–14 mm is a universal cutting tool for efficient holemaking and chamfering in thin metals and plastics, designed for use on standard drilling machines.

• HSS‑Co cutting material for high wear resistance
• 20° countersink angle for clean chamfering
• Universal for sheet metal and plastics
• 6 mm shank with three flats for secure clamping

Consistent chip control through a peeling cut

The combination of HSS‑Co as cutting material and the conically increasing, radially relieved cutting edges produces a peeling cut that reduces burr formation and improves hole quality in thin materials. The tool’s geometry, including a 20° chamfering angle and precisely ground flutes, minimises distortion in sheet work and lowers rework rates. For customers seeking repeatable results, this design reduces the need for secondary deburring and helps maintain production cadence without sacrificing edge integrity.

Robust holding and compatibility with common machines

Designed with a 6 mm shank featuring three flat faces, the drill ensures secure clamping in standard three‑jaw chucks and collets, preventing slippage at higher spindle speeds. The two‑flute arrangement balances cutting force and rigidity, enabling stable performance on bench drill presses and portable drilling units alike. The tool’s 58 mm overall length allows adequate reach in most setups while maintaining the stiffness required for clean penetration through sheet materials.

Broad application range and time‑saving productivity

This drill is specified for holes from 3 mm to 14 mm and is suitable for a wide spectrum of thin materials, notably sheet metal and various plastics. The radial back relief of the cutting edges supports controlled chip evacuation and reduces heat build‑up, which contributes to longer service intervals and improved tool life. In production environments where cycle time and surface quality are critical, the tool’s universal design reduces tooling variety and simplifies job setups, yielding measurable efficiency gains across repetitive tasks.

For supply, compatibility checks or ordering, contact Metav Werkzeuge GmbH: info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and prompt delivery from Emmerich.

Technical data

• Article number: 2000862021NW
• Brand: TECWERK
• Packaging unit: 1

Core data

• Cutting diameter range: 3–14 mm
• Overall length: 58 mm
• Shank diameter: 6 mm
• Number of cutting edges: 2
• Countersink angle: 20°

Special features

• Cutting material: HSS‑Co
• Shank with 3 flats for anti‑rotation
• Conically increasing, radially relieved cutting edges
• Universal tool for sheet metal and plastics
• Usable on standard drilling machines

FAQ

What materials can be machined with this drill?
The TECWERK sheet‑metal peel drill (SKU 2000862021NW) is intended primarily for sheet metal and a wide range of plastics, with geometry optimised to reduce burrs and maintain edge quality.

How does the tool achieve burr reduction on thin sheets?
The HSS‑Co composition and the conically increasing, radially relieved cutting edges of the TECWERK peel drill produce a peeling action that minimises material deformation and lowers the need for secondary deburring.

Is the shank compatible with standard chucks and collets?
Yes, the drill’s 6 mm shank with three flats ensures secure clamping in typical three‑jaw chucks and collets, providing stable performance in common drilling setups.

What makes this drill suitable for production use?
The combination of HSS‑Co wear resistance, a two‑flute design and an efficient chip‑control geometry gives the TECWERK sheet‑metal peel drill reliable tool life and consistent hole quality, supporting repetitive production tasks.

Are larger or smaller diameters available within the same design principle?
The current item (2000862021NW) covers the 3–14 mm range; variations in diameter that use the same peel‑cut geometry are offered under related product lines by TECWERK and can be recommended on request.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund