10mm Short HSS-Co PM End Mill, 4-Flute ALCRONA Coating, Weldon Shank - TECWERK

Take advantage of a short, high‑stiffness 10 mm cutter combining HSS‑Co PM metallurgy with an ALCRONA coating for reliable surface quality and reduced vibration; order directly via Metav Werkzeuge or request advice from our consultants for application‑specific selection.

TECWERK 10 mm HSS‑Co PM end mill (DIN 844 Type N) — ALCRONA coated, Weldon shank, 4‑flute short version

A TECWERK 10 mm HSS‑Co PM end mill engineered for short‑length milling and centre‑cut operations in steels, stainless steel and cast materials in workshop and industrial environments

• ALCRONA coating for longer wear resistance
• HSS‑Co PM construction for toughness and edge stability
• Four‑flute geometry for improved surface finish
• Weldon shank for secure clamping

High‑performance cutting for better productivity

The combination of HSS‑Co PM substrate and an ALCRONA finish delivers a balance of toughness and wear resistance that benefits demanding milling operations. Powder‑metallurgy steel ensures consistent microstructure for sharp, durable edges while the specialised coating reduces adhesive wear and increases tool life under intermittent loads. The four‑flute geometry moderates chip flow and helps achieve consistent surface quality, making this cutter suited to production tasks where repeatability and component finish are priorities.

Compact design that stabilises short‑length milling

Designed as a DIN 844 Type N, the short‑length format offers a low overhang and improved rigidity compared with longer cutters. The Weldon shank secures the tool against slip in high‑torque conditions, and the conical flute root increases overall stiffness for more accurate depth control. The centre‑cut configuration enables plunge operations when needed, so the tool covers common pocketing and shoulder milling tasks without compromise. Such compactness reduces chatter and supports predictable results on small to mid‑sized components.

Clear material suitability for efficient planning

This cutter is specified for machining materials with low to medium tensile strength up to approximately 1000 N/mm². It is rated as very good for steel, stainless steel and castings, while performance with certain non‑ferrous and specialised alloys is conditional. The right‑hand cutting direction and the unequal flute spacing provide vibration reduction, which improves surface finish and dimensional stability when machining tougher materials. These attributes aid process planning and mean fewer rejected parts and less rework under typical shop conditions.

Practical handling and workshop benefits

The tool’s measured geometry — modest cutting length and restrained profile — simplifies setting and reduces cycle‑time variability. Secure clamping with the Weldon interface combined with the cutter’s short length minimises run‑out and helps maintain concentricity in serial operations. Routine inspection of the cutting edges and adherence to appropriate feeds and speeds for HSS‑Co tools will preserve performance; the integrated measures against vibration also support higher effective feed rates while maintaining finish quality. For those seeking reliable, compact cutters that integrate into existing setups, this milling cutter offers a practical balance of durability and precision.

Contact Metav Werkzeuge for tailored application advice or to place an order for the TECWERK 10 mm HSS‑Co PM end mill — service and fast dispatch from Emmerich ensure a dependable supply to the workbench.

Technical Data

• Article number: 2000866035NW
• SKU: 2000866035NW
• Manufacturer: TECWERK
• Product type: End mill (short, DIN 844 Type N)
• Standard: DIN 844

Facts

• Diameter: 10 mm
• Shank diameter: 10 mm
• Overall length: 72 mm
• Effective length: 30 mm
• Cutting length: 4 mm
• Number of flutes: 4
• Relief: 9.5 mm
• Cutting direction: Right‑hand

Special features

• Material: HSS‑Co PM
• Coating: ALCRONA
• Weldon shank (for secure clamping)
• Centre‑cut for plunge milling
• Vibration reduction via unequal flute spacing
• Conical flute root for enhanced stiffness
• Suitable for machining up to approx. 1000 N/mm²
• Very good suitability: steel, stainless steel, castings
• Conditional suitability: non‑ferrous metals, special alloys

FAQ

What materials is this end mill best suited for?
The TECWERK end mill is very well suited for steel, stainless steel and castings, and is specified for materials up to about 1000 N/mm², with conditional performance on some non‑ferrous and special alloys.

Can this cutter be used for plunge milling?
Yes. The centre‑cut geometry of the TECWERK 10 mm HSS‑Co PM end mill permits plunge operations, enabling pocketing and spot‑facing tasks where a centre‑cut tool is required.

How does the ALCRONA coating affect performance?
The ALCRONA coating on this HSS‑Co PM cutter reduces adhesive wear and increases edge life, contributing to consistent surface quality over extended runs with the TECWERK tool.

Why is the Weldon shank important for workshop use?
The Weldon shank provides secure mechanical clamping, reducing the risk of slippage under torque and improving concentricity for the TECWERK end mill during repetitive milling operations.

What features reduce vibration during milling?
Unequally spaced flutes and a conical flute root are designed to deliver vibration reduction and increased stiffness, which supports improved surface finish and dimensional stability with the TECWERK cutter.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund