10mm Solid Carbide End Mill DIN 844 Type N HSS-Co8 4-Flute Short Center Cutting Weldon Shank, Right-Hand - TECWERK

Take advantage of the combination of high‑cobalt wear resistance, a secure Weldon shank and compact, short form factor to keep machining cycles reliable and setup times short; order directly from Metav Werkzeuge or consult our specialists for specification advice.

TECWERK short DIN 844 Type N end mill, 10 mm — HSS‑Co8, 4‑flute, Weldon

A TECWERK short DIN 844 Type N end mill designed for general workshop milling where compact tools, centre cutting and secure shank clamping are required.

• HSS‑Co8 high‑cobalt grade for durability
• DIN 844 short profile for compact setups
• Weldon shank with drive flat for secure mounting
• Centre‑cut 4‑flute geometry for controlled plunging

Robust cutting performance for medium‑strength materials

The HSS‑Co8 construction delivers a balance between toughness and red‑hardness, making this short end mill particularly suited to demanding intermittent cuts. The 4‑flute geometry supports higher feed rates while keeping chip formation steady, and the centre‑cut feature allows limited plunging when required. Together these characteristics provide a dependable tool for operations that prioritise consistent removal rates and low tool‑change frequency, reducing downtime and improving workflow predictability.

Secure clamping and compact design for tight setups

A Weldon shank with a drive flat ensures reliable torque transmission in collets and chucks, reducing slippage during heavy cuts. The short DIN 844 profile is intended for applications with limited tool overhang, improving rigidity and minimising chatter. This combination is advantageous in confined fixtures or multi‑axis setups where clamping stability directly affects surface finish and dimensional repeatability.

Material suitability and operational limits explained

The tool is optimised for machining steel and cast iron, where results are described as very good; non‑ferrous metals and stainless steels (INOX) are conditionally suitable according to application parameters. The data indicates uncoated tool performance up to approx. 800 N/mm², while coated variants can extend capability towards 1000 N/mm². These values guide the selection of cutting parameters and confirm the tool’s role for components in moderate strength ranges without presuming specialised coatings.

Practical workshop guidance and maintenance

Short‑length cutters reduce deflection and simplify set‑up verification, supporting faster cycle times and repeatable tolerances. Regular inspection of the cutting edges and correct collet seating for the Weldon shank preserves tool life; regrinding strategies should respect the original geometry to maintain the centre‑cut plunge capability. For tool changers and small machinist cells, the compact profile contributes to lower tool interference and easier toolpath programming.

For specification checks, tailored cutting data or to secure TECWERK DIN 844 short Type N HSS‑Co8 end mills with Weldon shank, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for prompt supply and expert advice.

Technical specifications

• Article number: 2000866332NW
• Label: Schaftfräser DIN 844 TypN D.10mm HSS‑Co8 Weldon Z.4 kurz TECWERK
• Manufacturer: TECWERK
• Packaging unit: 1
• UID: 2000866332NW

Key measurements and limits

• Diameter: 10 mm
• Flutes: 4
• Material grade: HSS‑Co8
• Standard: DIN 844
• Performance guidance: uncoated ≈ 800 N/mm², coated ≈ 1000 N/mm²

Features & applications

• Short DIN 844 Type N profile
• Centre‑cut (Zentrumschnitt) for limited plunging
• Cylindrical shank with drive flat (Weldon shank)
• Right‑hand cutting
• Suitable for steel: very good
• Suitable for cast iron: very good
• Suitable for non‑ferrous metals: conditionally suitable
• Suitable for stainless steel (INOX): conditionally suitable

FAQ

What materials are best machined with this end mill?
The TECWERK short DIN 844 Type N end mill is rated very good for steel and cast iron, with conditional suitability for non‑ferrous metals and stainless steel depending on cutting data.

Does the centre‑cut allow direct plunging into material?
Yes, the centre‑cut geometry permits limited plunging operations; the TECWERK tool is built for controlled entry but heavy plunging should be avoided to prevent premature wear.

Is the shank compatible with common toolholders?
The Weldon shank with a drive flat is compatible with standard Weldon‑style clamping systems and provides secure torque transmission in typical workshop chucks and holders.

Can this cutter be used for finishing passes?
The 4‑flute design balances material removal and surface quality, so the cutter can be used for semi‑finishing and some finishing tasks where the material suitability and feed/speed are correctly adjusted.

What indicates the difference between uncoated and coated performance?
Operational guidance shows uncoated tools perform up to approx. 800 N/mm², while coated variants can extend capability to around 1000 N/mm²; selection depends on the workpiece strength and desired tool life.

TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund