14mm Cutter DIN 844 HSS-Co8 4-Flute Short, 83mm Overall Length - TECWERK

Take advantage of the combination of HSS‑Co8 composition, a Weldon shank and a short, rigid geometry to maximise precision and minimise chatter in demanding milling tasks; order the cutter directly via Metav Werkzeuge or request advice from our technical consultants.

TECWERK End mill DIN 844 Type N, 14 mm HSS‑Co8, Weldon shank

The TECWERK End mill DIN 844 Type N, 14 mm is a short, four‑fluted HSS‑Co cutter designed for precise milling of steel and cast parts where rigidity and reliable clamping are decisive

• HSS‑Co8 grade for increased wear resistance
• Four cutting edges for fine surface finish
• Weldon shank for secure clamping
• Short design for greater rigidity

Reliable performance for medium‑strength materials

Constructed from HSS‑Co8, the cutter follows DIN 844 geometry and offers a balance between toughness and hardness suitable for many shop applications. The combination of the cobalt‑alloy steel and the four flutes yields stable cutting action with improved edge life when compared with plain HSS alternatives. The tool is specified for machining workpieces up to approx. 800 N/mm² in its uncoated state; when a suitable coating is applied, the application range can be extended further. This makes the cutter a rational choice for operations where sustained cutting and reliable tool life influence productivity.

Compact geometry for maximum rigidity and accuracy

The short overall length (83 mm) and a Weldon shank with a 12 mm shank diameter prioritise clamping stability and minimise deflection in deep cuts or slotting. The configuration includes an effective length 36 mm and a cutting length of 4 mm, offering a compact working envelope that reduces vibration and improves dimensional accuracy. Centre cutting geometry permits plunge passes where needed, while the Weldon flat ensures secure retention in chucks and holders commonly used in production environments.

Efficient chip removal and surface quality

With four cutting edges and a right‑hand helix, the cutter promotes consistent chip formation and evacuation, supporting a finer surface finish and reduced rework. The combination of balanced flute geometry and a short tool overhang increases material removal rate while maintaining stability, which translates into time savings and predictable results—especially beneficial in serial production or repair work. The centre‑cutting capability also allows controlled entry into the material, simplifying setup for pocketing and profile work.

Practical applications and workshop suitability

This short end mill is particularly suited to working with steel and castings, where rigidity and edge retention are priorities; non‑ferrous and stainless materials are conditionally suitable depending on cutting parameters and coolant use. Its compact form factor makes it useful in confined setups and toolrooms where minimising run‑out and tool bending is essential. Technical staff benefit from the clear specification of geometry and material, enabling straightforward integration into existing tool lists and process planning.

For secure procurement and application support for the TECWERK End mill (SKU 2000866336NW), contact Metav Werkzeuge for expert advice and local supply — eMail info@metav-werkzeuge.com or phone +49 2822 7131930

Technical data

• SKU: 2000866336NW
• Label: Schaftfräser DIN 844 Typ N D.14mm HSS‑Co8 Weldon Z.4 kurz TECWERK
• Norm: DIN 844

Facts

• Diameter: 14 mm
• Overall length: 83 mm
• Cutting length: 4 mm
• Effective length: 36 mm
• Shank diameter: 12 mm
• Number of flutes: 4
• Free grind: 11.5 mm
• Cutting direction: right‑hand cutting

Special features

• Material: HSS‑Co (HSS‑Co8)
• Weldon shank (Weldon flat)
• Centre cutting
• Short style for increased rigidity
• Suitability: Steel very well suited
• Suitability: Castings very well suited
• Suitability: Non‑ferrous metals conditionally suitable
• Suitability: Stainless steel conditionally suitable

FAQ

What materials is this cutter best suited for?
The TECWERK end mill is very well suited for steel and castings, with conditional suitability for non‑ferrous and stainless materials depending on cutting data.

Can this cutter be used for plunge milling?
Yes, the cutter features centre cutting geometry, allowing controlled plunge operations when required by the machining strategy.

What clamping system is recommended for this tool?
A secure Weldon‑style holder or collet with a Weldon flat is recommended to exploit the cutter’s short geometry and maintain rigidity with the 12 mm shank.

Does the tool require a coating for harder materials?
The supplied tool is uncoated and rated up to approx. 800 N/mm²; a suitable coating will extend performance toward 1000 N/mm², provided the coating type matches the application.

Which DIN standard defines the geometry of this cutter?
The cutter conforms to DIN 844 specifications for short, four‑fluted end mills in Type N geometry.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund