2mm Solid Carbide End Mill DIN 844 Type N 4 Flute TiCN Coating, 4mm Cut Length - TECWERK

Take advantage of the combination of precise material suitability, enhanced wear resistance and secure clamping for dependable short‑reach milling. Order the tool directly via Metav Werkzeuge or consult the specialists for tailored application advice.

TECWERK HSS‑Co8 End Mill DIN 844 Type N – 2 mm, TiCN Coating

A TECWERK HSS‑Co8 end mill DIN 844 Type N engineered for precision milling in short‑reach operations on steel and stainless steel components.

TiCN coating for extended tool life
HSS‑Co8 for high wear resistance
Four‑flute, centre‑cut geometry
Weldon shank for secure clamping

Precision and performance for demanding short‑reach milling

The TECWERK HSS‑Co8 end mill combines a high‑alloy HSS‑Co8 substrate with a TiCN surface finish to balance toughness and wear resistance. The small 2 mm diameter and short overall length support tight tolerances in confined setups while the DIN 844 specification ensures compatibility with established workshop practices. As a result, milling tasks that demand repeatable accuracy—such as finishing narrow slots or trimming small features—benefit from reduced vibration and consistent cutting forces.

Geometry that increases productivity and surface quality

The four‑flute configuration with centre‑cut geometry delivers an efficient chip evacuation and improved surface finish on through and partial cuts. The short tool form reduces overhang, increasing rigidity for steadier cuts and longer tool life. A Weldon clamping flat on the 6 mm shank ensures a secure hold in collets or holders designed for Weldon tools, minimising slippage under heavier feeds while maintaining run‑out stability for fine finishing passes.

Material suitability explained for reliable process planning

This cutter is rated very good for machining steel and cast iron, and very good for stainless steel (INOX). It is conditionally suitable for non‑ferrous metals and certain special alloys. With an uncoated tool the practical feed‑and‑speed window covers materials up to approximately 800 N/mm², and with the TiCN coating that capability extends to about 1000 N/mm², allowing confident selection for medium‑strength to higher‑strength steels when appropriate cutting data is applied.

Handling, tool life and integration into the workshop

The compact design and right‑hand cutting orientation make the cutter straightforward to integrate into CNC programmes and manual milling tasks requiring precise positioning. The 4 mm cutting length and 7 mm effective length are optimised for shallow slotting and contouring; the short overhang maximises rigidity for higher feed rates within recommended parameters. The TiCN finish reduces built‑up edge and wear during intermittent cuts, translating into longer tool life and fewer tool changes in production runs.

For application advice, clamping compatibility checks or rapid supply from Emmerich, contact Metav Werkzeuge to discuss the TECWERK end mill and ensure the optimal specification for the intended material and process.

Technical Data

• Article number: 2000866344NW
• SKU: 2000866344NW
• Norm: DIN 844
• Product type: End mill (shank cutter)
• Manufacturer: TECWERK

Facts

• Diameter: 2 mm
• Overall length: 51 mm
• Cutting length: 4 mm
• Effective length: 7 mm
• Shank diameter: 6 mm
• Number of flutes: 4

Special features

• Material: HSS‑Co8
• Coating: TiCN
• Type: DIN 844 Type N, short
• Geometry: Four‑flute, centre‑cut
• Shank: Weldon flat (secure clamping)
• Cutting direction: Right‑hand cutting
• Application strength (uncoated): up to ≈ 800 N/mm²
• Application strength (coated): up to ≈ 1000 N/mm²
• Suitability steel: very good
• Suitability stainless steel: very good
• Suitability non‑ferrous metals: conditional
• Suitability special alloys: conditional
• Application: milling of low to medium strength materials

FAQ

What materials is this end mill best suited for?
The TECWERK HSS‑Co8 end mill is very well suited for steel and stainless steel; it is conditionally suitable for non‑ferrous metals and special alloys.

Can this cutter machine hardened steels?
The tool is intended for low to medium strength materials; with TiCN coating it is applicable up to about 1000 N/mm², beyond which alternative grades are recommended.

Is the shank compatible with standard Weldon holders?
Yes, the tool features a Weldon flat on the 6 mm shank for secure clamping in holders designed for Weldon shank tools.

Does the cutter allow plunging operations?
The centre‑cut geometry permits limited plunging and entry cuts; for extensive plunge milling a dedicated centre‑cut end mill with deeper cutting length is advised.

How does the TiCN coating benefit manufacturing?
The TiCN coating reduces wear and built‑up edge, extending tool life and improving surface finish under recommended cutting parameters.

What is the article number for ordering and reference?
Reference SKU 2000866344NW for the TECWERK HSS‑Co8 end mill (DIN 844 Type N, 2 mm, TiCN, 4‑flute).

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund