8mm Solid Carbide End Mill DIN 844 Type N 4-Flute TiCN Coated Weldon Shank Short, Centre Cutting - TECWERK

Take advantage of the combination of a cobalt-enhanced HSS body, a centre-cut geometry and a secure Weldon shank for reliable short-reach milling in production and workshop environments. Order the cutter directly via Metav Werkzeuge or consult the team for application-specific advice.

Schaftfräser DIN 844 TypN D.8mm HSS-Co8 TiCN Weldon Z.4 kurz – short 4‑flute HSS‑Co8 end mill by TECWERK

The Schaftfräser DIN 844 TypN D.8mm HSS-Co8 TiCN Weldon Z.4 kurz is a short, four‑flute end mill designed for machining medium to high‑strength materials where rigidity and precise cutting are required

• HSS‑Co8 solid for improved heat resistance
• DIN 844 Type N four‑flute geometry
• Weldon shank with drive flat for secure clamping
• Centre‑cut for limited plunge milling

Consistent cutting performance for medium‑strength materials

The combination of HSS‑Co8 construction and a compact geometry provides a dependable balance between toughness and wear resistance. The tool is specified for work on materials up to 800 N/mm² with an uncoated cutter and up to 1000 N/mm² when a coating is applied, offering a predictable basis for process planning. The centre‑cut design allows controlled plunging where short axial engagement is required; this reduces setup complexity when axial entry is unavoidable and supports efficient one‑pass operations in short‑reach applications.

Secure clamping and rigidity for short‑reach tasks

A Weldon shank with drive flat ensures positive torque transmission in set‑screw holders and reduces slippage under load. The short overall length increases stiffness, which minimises deflection and promotes consistent dimensional accuracy during side and face milling. The four‑flute layout provides a compromise between surface finish and chip evacuation; in interrupted cuts the geometry maintains stability while the right‑hand cutting orientation suits standard milling directions in most machine setups.

Clear suitability across common workshop materials

Material compatibility is documented: steel, stainless steel and cast iron are very well suited to this cutter, while non‑ferrous metals and certain high‑performance alloys are conditionally suitable. The presence of a TiCN designation in the product name indicates an option for coated variants; in practice a coated tool extends the usable hardness range to 1000 N/mm², which can be decisive for harder stainless steels and some alloyed steels. For applications in non‑ferrous or exotic materials, trials and adjusted parameters are advised before series production.

Practical integration and process reliability

The compact, short design simplifies tool management in production cells where tool length and tool change times affect cycle consistency. The combination of centre‑cut geometry and an effective clamping interface supports small series and repair work as well as mixed production environments. Process planners benefit from predictable behaviour under the stated load ranges, and procurement gains from a tool that reduces the need for multiple specialised cutters where short‑reach, robust performance is required.

For application advice or to secure a reliable supply of TECWERK HSS‑Co8 end mills, contact Metav Werkzeuge in Emmerich for dedicated consultancy and prompt delivery.

Technical Data

• Article number: 2000866354NW
• Manufacturer: TECWERK
• SKU: 2000866354NW

Facts

• Diameter: 8 mm
• Flutes: Z = 4
• Material grade: HSS‑Co8
• Rated material strength (uncoated): up to 800 N/mm²
• Rated material strength (coated): up to 1000 N/mm²

Special features

• DIN 844, Type N
• Short design
• Centre‑cut (plunge capable)
• Cylindrical shank with drive flat (Weldon)
• Right‑hand cutting direction
• TiCN listed in designation
• Very good suitability: steel, stainless steel, cast iron
• Conditional suitability: non‑ferrous metals, special alloys

FAQ

Which materials is this cutter best suited for?
The TECWERK short end mill (SKU 2000866354NW) is very well suited for steel, stainless steel and cast iron; non‑ferrous metals and special alloys are only conditionally suitable.

Can the cutter be used for plunge or drilling entry?
Yes, the centre‑cut geometry permits limited plunge milling; the tool is designed for short axial entry rather than full bore drilling.

What does the Weldon shank provide in practice?
A Weldon shank with drive flat offers secure clamping in set‑screw holders and reduces the risk of slippage under torsional load during heavy side cuts.

Does the tool require a coated variant for harder steels?
A coated variant increases the allowable machining strength to approximately 1000 N/mm², so coating is recommended for harder stainless or alloyed steels within that range.

Is this cutter intended for long‑reach milling?
No, the short design prioritises rigidity and accuracy in short‑reach operations rather than extended overhangs or long‑reach applications.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund