10mm Long HSS-Co Solid Carbide Shank End Mill TiCN Coating, 53mm Cutting Length, DIN 844 - TECWERK

Take advantage of a long-reach HSS‑Co construction and a TiCN surface for extended tool life and reliable performance in demanding steels; combine these with a secure Weldon shank for vibration‑resistant clamping. Order the end mill directly via Metav Werkzeuge or consult our specialists for machining recommendations.

End mill DIN 844 Type N, 10 mm — HSS‑Co8, TiCN, 4‑flute (TECWERK)

The TECWERK end mill is a long, centre‑cutting DIN 844 Type N tool designed for general milling of medium‑strength and stainless steels, offering a 10 mm diameter and a 53 mm effective cutting length.

High‑strength HSS‑Co8 construction TiCN coating for extended tool life 4‑flute geometry for stable machining Weldon shank for secure clamping

Consistent high performance in steel milling

The combination of HSS‑Co substrate and a TiCN coating provides a balance of toughness and wear resistance that benefits production environments. Coated tools extend cutting capability up to about 1200 N/mm² for harder operations, while the uncoated baseline remains effective up to 800 N/mm². This makes the tool especially suitable for prolonged machining cycles where flank wear and thermal load must be controlled. The 4‑flute geometry reduces radial run‑out and supports steady chip evacuation when machining steels and cast materials.

Long reach and precise geometry for deeper pockets

A 53 mm effective cutting length paired with a 95 mm overall length enables access to deeper cavities without sacrificing rigidity. The 10 mm diameter combined with centre‑cutting capability allows plunge entry and axial engagement for operations where conventional side‑entry is impractical. The Weldon shank secures the tool in holders with drive flats to minimise slippage during heavy cuts, maintaining repeatable concentricity and surface finish across batch runs.

Reliable tool life and process integration

Conformity with DIN 844 Type N and the long‑reach design make the cutter a dependable choice for mixing shop flexibility with industrial standards. The tool shows very good suitability for steel, stainless steel (INOX) and cast materials, with conditional use in non‑ferrous metals and special alloys. Integrating this cutter into regular production contributes to predictable tool change intervals and stable cycle times; pairing coated cutters with appropriate feeds and speeds reduces downtime and supports consistent throughput. For complex setups or specialised alloys, consult machining data to match coolant and spindle parameters.

For procurement or technical guidance on long‑reach milling with TECWERK tools, contact Metav Werkzeuge—order the cutter via Metav Werkzeuge or request tailored feed and speed recommendations at +49 2822 7131930 or info@metav-werkzeuge.com

Technical data

• SKU: 2000866402NW
• Standard: DIN 844
• Product type: End mill
• Manufacturer: TECWERK

Dimensions and core data

• Diameter: 10 mm
• Overall length: 95 mm
• Effective cutting length: 53 mm
• Shank diameter: 10 mm
• Flutes: 4
• Relief / clearance: 9.5 mm

Materials and special features

• Substrate: HSS‑Co (high‑speed steel with cobalt)
• Coating: TiCN (titanium carbonitride)
• Cutting direction: right‑hand cutting
• Type: DIN 844, Type N, long, centre cutting
• Shank: cylindrical with drive flat (Weldon)
• Material suitability: steel — very good; stainless steel (INOX) — very good; cast — very good; non‑ferrous metals — conditional; special alloys — conditional
• Intended application: milling of materials with low to medium strength; improved performance with coated tool up to ~1200 N/mm²

FAQ

What materials is this end mill best suited for?
The TECWERK end mill (end mill, SKU 2000866402NW) is very well suited for steel, stainless steel (INOX) and cast materials; non‑ferrous metals and special alloys are conditionally suitable.

Does the TiCN coating significantly extend tool life?
Yes, the TiCN coating on this TECWERK HSS‑Co cutter improves wear resistance and allows the coated version to handle higher tensile strengths (up to approximately 1200 N/mm²) compared with the uncoated tool.

Can the tool be used for plunge milling?
The cutter is centre‑cutting (Type N) and therefore capable of axial engagement; the design supports plunge operations within recommended feed and speed ranges.

Which shank type is provided for secure clamping?
The tool features a Weldon style drive flat on a cylindrical shank for secure clamping in set‑screw holders, ensuring torque transmission under higher cutting loads.

Is this cutter compliant with industry standards?
Yes, the design conforms to DIN 844 Type N, offering compatibility with standard tooling systems and predictable performance in industrial settings.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund