10mm Solid Carbide End Mill TiAlN Coated 35° Helix 4 Flute Short Extra-Cut, DIN 6527 - TECWERK

Take advantage of the combination of solid carbide construction, TiAlN coating and a compact, extra-short design for vibration‑reduced machining and consistent surface quality. Order the TECWERK end mill directly via Metav Werkzeuge or consult the team for application advice.

TECWERK End Mill WN Type N – Ø10 mm, Solid Carbide, TiAlN, 4 Flutes, 35° Helix

TECWERK End Mill WN Type N is an extra‑short, centre‑cut solid carbide end mill designed for high‑performance roughing and finishing across a wide range of metals

*TiAlN-coated solid carbide for longevity and heat resistance
*Extra-short, rigid design for low-vibration cutting
*HPC geometry with unequal pitch for stable chip evacuation
*Centre-cutting, right-hand 4-flute for versatile machining

High-performance cutting tailored for industrial production

The combination of solid carbide (VHM) and a TiAlN coating delivers a high thermal resistance and extended edge life under elevated cutting temperatures. The 35° helix paired with the HPC geometry and unequal pitch reduces cutting forces and optimises chip flow, which results in consistent surface finishes and predictable tool life during both roughing and finishing operations. This specification is particularly suited to machining tasks that require repeatable results in mixed production runs.

Robust design for vibration‑reduced machining and precision grooves

An extra-short, rigid construction with a cylindrical shank to DIN 6535 HB minimises overhang and supports stable toolholding in standard collets. The tool’s centre‑cutting capability and four flutes enable plunge cuts and short groove work, while the moderate 10° soft‑cut characteristic helps absorb chatter in less rigid setups. These features combine to lower the risk of premature tool failure and to maintain dimensional accuracy on workpieces such as steels up to 45 HRC and grey cast iron.

Broad material suitability and explained benefits

The cutter is optimised for a variety of materials: very good performance in steel and cast iron, and conditional suitability for stainless steel (INOX) and non‑ferrous alloys such as aluminium, copper and brass. The TiAlN layer forms a protective barrier that reduces adhesive wear and increases resistance to oxidation at high temperatures, making the tool appropriate for longer cycles and elevated cutting speeds. The fine‑grain carbide substrate enhances toughness and wear resistance, providing a cost‑effective balance between life and performance in series production.

Contact Metav Werkzeuge for application guidance and dependable supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss delivery times and technical suitability.

Technical Data

• SKU: 2000866416NW
• Standard: DIN 6527
• Label: Schaftfräser WN TypN D.10mm VHM TiAlN 35Grad HB Z.4 ext.kurz TECWERK
• Manufacturer: TECWERK

Facts

• Diameter: 10 mm
• Overall length: 50 mm
• Cutting length: 4 mm
• Shank diameter: 10 mm
• Number of flutes: 4
• Helix angle: 35°
• Protection chamfer: 0.2 mm

Special features

• Material: solid carbide (fine‑grain VHM)
• Coating: TiAlN
• Type: N / HPC geometry, unequal pitch
• Cutting direction: right‑hand
• Centre cutting: yes
• Shank standard: cylindrical shank to DIN 6535 HB
• Short, stable design with soft cut (~10°)
• Suitable for: steel (very good), cast iron (very good), INOX (conditional), non‑ferrous metals (conditional)
• Application: high‑performance cutting (HPC), roughing, finishing, slotting

FAQ

What materials is this end mill best suited for?
The TECWERK end mill with TiAlN coating and fine‑grain solid carbide substrate is rated very good for steel and cast iron, and conditionally suitable for stainless steel and various non‑ferrous metals.

Can the cutter be used for plunge cutting and slotting?
Yes, the centre‑cutting geometry and four‑flute configuration allow plunge operations and short slotting, while the extra‑short design reduces overhang‑related vibration.

How does the TiAlN coating benefit production runs?
The TiAlN coating increases thermal resistance and reduces adhesive wear, enabling longer tool life under higher cutting speeds and improving process stability across batch production.

Is the shank compatible with standard toolholders?
The tool features a cylindrical shank manufactured to DIN 6535 HB, which suits standard collet systems and ensures secure clamping for precision work.

What distinguishes the HPC geometry in this tool?
The HPC geometry, combined with unequal pitch, reduces harmonics and improves chip evacuation; this results in more stable cutting, improved surface quality and predictable tool life.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund