12mm Solid Carbide End Mill TiAlN Coating 35° Helix 4-Flute Extra Short, DIN 6527 - TECWERK

Take advantage of the combination of high material removal rates, TiAlN heat resistance and a short, rigid design for vibration‑reduced machining; order the cutter directly via Metav Werkzeuge or ask the consultants for application advice.

TECWERK solid carbide end mill WN Type N, Ø12 mm, TiAlN-coated, 4‑flute (extra short)

The TECWERK solid carbide end mill WN Type N is an extra‑short, TiAlN‑coated 4‑flute cutter designed for high‑performance roughing and finishing in steel, cast iron and a range of non‑ferrous materials.

• Solid carbide, TiAlN coating for heat resistance
• Extra-short design for rigid, vibration-free cutting
• 4-flute, centre-cutting for plunge and slotting
• Suitable for steel, cast iron and non-ferrous metals

Faster stock removal with stable, HPC geometry

The cutter features proven HPC geometry and an unequal pitch that reduces harmonic excitation during cutting, enabling higher feed rates with consistent results. The TiAlN coating raises thermal resistance and preserves edge integrity under elevated cutting temperatures, while the solid carbide body offers stiffness for sustained metal removal. Together these characteristics support efficient roughing cycles and enable improved surface finish in follow‑up operations, reducing rework and cycle variability.

Broad material capability for mixed production runs

Engineered for machining a wide spectrum of workpieces, the tool is very well suited to general steel and cast iron applications and offers conditional use in stainless and many non‑ferrous alloys. The tool’s geometry and centre‑cutting design allow controlled plunging and slotting in operations where direct entry is required. For mixed batches where setups must remain lean, this cutter provides a practical balance of versatility and predictable performance.

Short overhang and precise shank for reduced vibration

The extra‑short configuration, combined with a cylindrical shank to DIN 6535 HB and h6 tolerance, gives a compact, rigid assembly that lowers the risk of chatter and improves tool life. A protective chamfer of 0.2 mm and a moderate 35° helix contribute to smooth chip flow and a softer cutting action (nominal 10°), which helps maintain surface quality while extending edge durability. These mechanical choices translate directly into fewer process interruptions and steadier component quality on the shop floor.

Integrates easily into production workflows

With a 4‑flute layout and right‑hand cut configuration, the cutter is optimised for conventional feed directions and standard toolholders, simplifying workstation integration. The capacity for both roughing and finishing in a single tool reduces tool changes and shortens setup times. In combination with modern CNC strategies prioritising high feed and stable engagement, this cutter supports reproducible results and contributes to predictable throughput in repetitive production environments.

Secure supply and application support through Metav Werkzeuge — request machining recommendations or order the TECWERK cutter via Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930

Technical Data

• Article number: 2000866417NW
• Standard: DIN 6527
• Manufacturer: TECWERK

Facts

• Diameter: 12 mm
• Overall length: 55 mm
• Cutting length: 4 mm
• Flutes: 4
• Helix angle: 35°
• Shank diameter: 12 mm

Materials & Special features

• Material: solid carbide (VHM)
• Coating: TiAlN
• Right‑hand cut
• Extra short design
• Centre‑cutting (plunge capable)
• Cylindrical shank to DIN 6535 HB, tolerance h6
• Unequal pitch for vibration damping
• Protective chamfer: 0.2 mm
• Soft cutting geometry (approx. 10°)
• Suitable for steel up to 45 HRC, cast iron, stainless steel (conditional), copper, brass, aluminium

FAQ

What machining tasks is this cutter best suited for?
The TECWERK solid carbide end mill WN Type N is designed for high‑performance roughing and finishing, including slotting, pocketing and plunge operations where a short, rigid tool is required.

Can this cutter be used for stainless steel?
Stainless steel (INOX) is conditionally suitable for this cutter; the TiAlN coating and HPC geometry help, but cutting data should be adjusted for stainless machining to control heat and work hardening.

Is the tool capable of plunge cutting?
Yes — the tool is centre‑cutting, which permits controlled plunging and makes it suitable for operations requiring direct entry.

Which shank standards and tolerances apply?
The cutter is supplied with a cylindrical shank to DIN 6535 HB and a shank tolerance of h6 for accurate clamping and reduced runout.

What is the SKU for ordering and reference?
Reference SKU 2000866417NW for ordering the TECWERK solid carbide end mill WN Type N.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund