6mm Solid Carbide End Mill TiAlN Coated 4-Flute 16mm Effective Length DIN 6527 - TECWERK

Take advantage of a high-performance, short solid carbide solution with TiAlN surface treatment and a compact 6 mm diameter for stable, high-speed milling cycles; order directly via Metav Werkzeuge or consult the team for application-specific advice.

End Mill DIN 6527K Type N/HPC – 6 mm, solid carbide with TiAlN (TECWERK)

An End Mill DIN 6527K Type N/HPC designed for high-performance roughing and finishing across steels, cast irons and non-ferrous alloys.

• Solid carbide, TiAlN coating
• 6 mm diameter, 16 mm effective length
• Four flutes with centre cutting for plunging
• Short design with neck relief for low vibration

High-speed performance for shorter cycle times

The cutter combines a solid carbide body with a hard TiAlN surface layer to raise heat resistance and wear life during demanding HPC work. The four-flute geometry and the centre-cutting capability enable axial plunging and efficient chip evacuation, which reduces tool-change frequency and shortens overall machining cycles. As a result, machining programmes run more economically while maintaining consistent material removal rates and surface integrity.

Broad material suitability for flexible job scheduling

Designed with a universal geometry, the tool performs well in a wide range of materials: steel, cast iron, stainless steel, aluminium with silicon, and various non-ferrous and special alloys. The cutter’s configuration supports both roughing and finishing passes, making it suitable for shops that prioritise flexibility. When abrasive or alloyed materials impair other tools, the combination of substrate and coating keeps tolerances stable over longer tool lives.

Built for precision and vibration control

A short shank and a neck relief minimise overhang-induced deflection, while an unequal pitch reduces harmonic chatter in interrupted or deep cuts. The shank conforms to DIN 6535 HB with a tight h6 tolerance for reliable clamping and concentricity. The tool also features a 45° chamfer and a protective micro‑bevel to safeguard the cutting edge during entry, supporting repeatable part quality in serial production.

Compact dimensions that simplify fixture and tool planning

With a 6 mm nominal diameter, a cutting length of 4 mm and an effective length of 16 mm, the cutter fits compact tool assemblies and shorter holders for enhanced rigidity. The short design and right-hand cutting direction suit stable setups and allow easy integration into existing tool cycles without major programme changes. This balance of size and capability makes the cutter a practical choice for tooling inventories aiming to reduce the number of specialised tools required.

For precise application advice or stock enquiries about the TECWERK TiAlN-coated solid carbide end mill, contact Metav Werkzeuge directly at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific materials and processes

Technical data

• SKU: 2000866484NW
• Standard: DIN 6527
• Product type: End mill
• Manufacturer: TECWERK

Facts

• Diameter: 6 mm
• Cutting length: 4 mm
• Effective length: 16 mm
• Overall length: 54 mm
• Shank diameter: 6 mm
• Number of flutes: 4
• Free relief (neck): 5.8 mm
• Chamfer (protection): 0.12 mm

Special features

• Solid carbide (fine grain)
• TiAlN coating
• DIN 6527 K · Type N / HPC
• Centre cutting (axial plunge)
• Short design for reduced overhang
• 45° protective chamfer
• Cylindrical shank to DIN 6535 HB, tolerance h6
• Unequal pitch for vibration reduction
• Right‑hand cutting
• Neck relief for vibration‑reduced machining
• Suited for roughing and finishing
• Suitable for steel, cast iron, stainless steel, non‑ferrous alloys and abrasive materials

FAQ

Is this cutter suitable for plunge milling?
Yes. The TECWERK end mill is centre cutting, so axial plunging is possible; the four‑flute geometry supports chip evacuation during plunge operations.

Which materials does the tool perform best in?
The tool is optimised for a broad range: steel, cast iron, stainless steel and non‑ferrous alloys, including aluminium with silicon content, offering very good suitability across these materials.

What advantage does the TiAlN coating provide?
The TiAlN layer increases thermal stability and wear resistance, extending tool life in high‑speed and high‑temperature conditions compared with uncoated carbide.

How does the short shank affect performance?
The short design reduces overhang, improves rigidity and minimises vibration, which enhances dimensional accuracy and surface finish in both roughing and finishing passes.

Can this cutter be clamped in standard DIN toolholders?
Yes. The shank is a cylindrical type compliant with DIN 6535 HB and a h6 tolerance, ensuring secure and concentric clamping in standard holders.

Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund