10mm Solid Carbide End Mill TiAlN Coated 4-Flute HPC 24mm Cut Length, DIN 6527 - TECWERK

Benefit from the combination of solid carbide construction, TiAlN surface hardening and a short HPC geometry for faster cycles and long tool life; order the end mill directly via Metav Werkzeuge or ask our consultants if needed.

TECWERK Solid Carbide End Mill DIN 6527K Type N — 10 mm, TiAlN, 4‑flute

The TECWERK solid carbide end mill DIN 6527K Type N is a short, high‑performance cutter developed for vibration‑reduced roughing and finishing across steels, cast irons and non‑ferrous alloys.

• Solid carbide, TiAlN‑coated for long tool life
• Four‑flute design for efficient chip evacuation
• Short HPC geometry for vibration‑reduced machining
• Cylindrical shank DIN 6535 HB, centre cutting

Faster cycles through optimised HPC geometry

The combination of a fine‑grain solid carbide core and TiAlN coating gives a tool that withstands elevated cutting temperatures and resists built‑up edge, enabling more aggressive feeds and higher cutting speeds. The short HPC geometry increases rigidity compared with long variants, which helps to shorten cycle times while maintaining surface finish. The four‑flute configuration balances chip load and contact area, making the cutter suitable for both high‑material‑removal and finishing passes without sacrificing tool life.

Stable machining and reduced vibration for consistent parts

An unequal helix and a carefully developed flute geometry distribute cutting forces so harmonics are minimised; this results in a vibration‑reduced cut and better surface integrity on the workpiece. The tool’s neck relief permits closer approach to walls and pockets without rubbing, while the 0.2 mm protection chamfer guards the cutting edge during repositioning. Together these features make the cutter a reliable choice for repeatable, high‑quality production where cycle stability matters.

Versatile material capability for workshop flexibility

The tool is designed as a universal high‑performance cutter: the TiAlN layer improves heat resistance for steel and alloy machining, while the substrate and geometry also perform very well in cast irons, non‑ferrous metals and abrasive aluminium alloys containing silicon. The centre‑cutting property allows plunge operations in addition to peripheral milling, expanding its application range from slotting to pocketing. For operations that mix roughing and semi‑finishing, this cutter reduces the need for frequent tool changes.

Precision shank and reliable concentricity for machine uptime

The end mill is supplied with a cylindrical shank to DIN 6535 HB and a shank tolerance of h6, ensuring tight concentricity in collets and holders. Low run‑out preserves cutting edge life and reduces spindle load, which supports longer unattended runs. The right‑hand cutting orientation and centre‑cut design simplify programming and toolpath planning on conventional and CNC machines, supporting predictable production output with less manual adjustment.

For HPC milling tasks that demand a balance of speed, wear resistance and stability, contact Metav Werkzeuge to source the TECWERK solid carbide end mill and receive tailored application advice from our specialists in Emmerich.

Technical data

• Article number: 2000866486NW
• Standard: DIN 6527
• Material: solid carbide (VHM)
• Coating: TiAlN
• Product type: solid carbide end mill
• Manufacturer: TECWERK

Core data

• Diameter: 10 mm
• Overall length: 66 mm
• Effective/cutting length: 24 mm
• Free relief (neck relief): 9.5 mm
• Number of flutes: 4
• Cutting direction: right‑hand
• Protection chamfer: 0.2 mm
• Packaging unit: 1

Special features

• HPC geometry, short version
• Type N (DIN 6527K)
• Four‑flute, centre cutting
• Cylindrical shank to DIN 6535 HB, shank tolerance h6
• Unequal helix for reduced vibration
• Neck relief for machining close to walls
• 45° protection chamfer
• Suitable for steel, cast iron, gray iron, malleable iron, Cr‑Ni steels, non‑ferrous metals, aluminium with silicon and abrasive materials
• Optimised for roughing and finishing

FAQ

What materials is this end mill best suited for?
The TECWERK solid carbide end mill with TiAlN coating is very well suited for steel, cast iron, non‑ferrous metals and aluminium alloys with silicon content, offering reliable performance across a wide material range.

Can the cutter be used for plunge milling?
Yes. The centre‑cutting geometry of the TECWERK end mill allows plunge‑milling operations as well as peripheral milling, enabling versatile use in pocketing and slotting.

What advantages does the TiAlN coating provide?
The TiAlN coating increases heat resistance and reduces adhesive wear, resulting in longer tool life and improved performance during high‑speed or high‑temperature machining.

How does the unequal helix benefit production stability?
The unequal helix disrupts harmonic frequencies during cutting, reducing vibration and improving surface finish and tool life, which is especially beneficial in interrupted cuts or when machining thin walls.

Which shank standard and tolerance does the tool use?
The cutter features a cylindrical shank to DIN 6535 HB with h6 tolerance to ensure consistent concentricity and reduced run‑out in precision holders.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund