12mm Solid Carbide End Mill TiAlN Coated 4-Flute 26mm Cutting Length DIN 6527 K - TECWERK

Take advantage of solid carbide construction and TiAlN coating for high‑speed, wear‑resistant cutting, combined with a short, rigid design for vibration‑reduced roughing and finishing. Order the tool directly via Metav Werkzeuge or consult the technical team for cutting data and process advice.

TECWERK solid carbide end mill DIN 6527K | 12 mm, TiAlN, 4 flutes

The TECWERK solid carbide end mill DIN 6527K is a short, four‑flute HPC tool engineered for vibration‑reduced roughing and finishing in steels, cast materials and non‑ferrous alloys.

• Solid carbide with TiAlN coating
• 4 flutes for high material removal
• Short design for rigidity and stability
• Shank to DIN 6535 HB, tolerance h6

Consistent high cutting performance for mixed materials

The tool pairs a solid carbide body with a TiAlN surface treatment to deliver high thermal resistance and prolonged edge life under elevated cutting speeds. This combination makes the cutter particularly effective for HPC applications in steels, cast iron and non‑ferrous alloys where temperature control and flank wear are critical. The coating reduces built‑up edge and improves wear resistance, so fewer tool changes are required and component tolerances stay consistent.

Geometry that reduces vibration and improves surface finish

A 4‑flute geometry with unequal pitch minimises harmonic excitation for smoother cuts and better tool stability. The cutter is centre‑cutting and right‑hand fluted, enabling axial entry and reliable plunge work when required. The short overall form increases stiffness, which benefits both roughing and light finishing passes by reducing chatter and delivering repeatable surface quality in one setup.

Tool interface and key dimensions for straightforward setup

Critical dimensions are optimised for workshop integration: 12 mm diameter, 26 mm effective cutting length and 73 mm overall length. The shank is manufactured to DIN 6535 HB with h6 tolerance for secure clamping and concentricity in standard holders. A 0.2 mm protective chamfer and a defined neck relief further support high‑feed stability and reduce the risk of interference during trochoidal or ramping strategies.

Process advantages and recommended applications

Designed for HPC machining, the new geometry and coating make the cutter suitable for both heavy material removal and fine finishing passes with fewer operations. The combination of vibration‑reduced design and centre cutting capability supports efficient machining of INOX, special alloys and abrasive materials while maintaining tool life. For process optimisation or material‑specific cutting values, technical advice is available to adapt feeds and speeds to individual machines.

Contact Metav Werkzeuge in Emmerich for tailored cutting data or to secure the TECWERK solid carbide end mill with TiAlN coating

Technical data

• Article number: 2000866487NW
• Manufacturer: TECWERK
• Standard: DIN 6527
• Type: End mill

Data

• Diameter: 12 mm
• Overall length: 73 mm
• Effective cutting length: 26 mm
• Neck clearance: 11.5 mm
• Flutes: 4
• Shank diameter: 12 mm
• Protection chamfer: 0.2 mm

Special features

• Solid carbide, fine‑grain
• TiAlN coating
• 45° protective chamfer
• Centre‑cutting, right‑hand cutting
• Unequal pitch for vibration reduction
• Suitable for steel, cast iron, stainless, non‑ferrous, aluminium with silicon and abrasive materials
• Shank to DIN 6535 HB, tolerance h6
• Short design for HPC, suitable for roughing and finishing
• Neck relief for vibration‑reduced machining

FAQ

Is this cutter suitable for stainless steels and Inox?
The TECWERK solid carbide end mill DIN 6527K is rated very good for INOX and stainless steels; the TiAlN coating and fine‑grain carbide substrate support wear resistance in these materials.

Can this tool be used for both roughing and finishing?
Yes, the combination of the short, rigid form and the specially developed geometry allows the cutter to handle HPC roughing as well as light finishing passes with consistent surface quality.

What toolholder interface is required?
The shank conforms to DIN 6535 HB with h6 tolerance, so standard holders compatible with DIN 6535 HB shanks are appropriate for secure clamping.

Does the cutter support plunge cutting?
The tool is centre‑cutting, enabling plunge operations when the process requires axial entry; right‑hand cutting direction applies for standard milling routines.

Which materials perform best with this tool?
The cutter is designed for a wide range of materials: steels, cast iron, hard materials, special alloys, non‑ferrous metals and aluminium with silicon content, as noted in the technical features.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund