2mm Full Radius Cutter 10mm Effective Length TiCN Coated HSS-Co8 Extra Short Weldon Shank, Right-Hand - TECWERK

Take advantage of the tool's combination of HSS‑Co8 core and TiCN coating for extended life, together with the extra‑short geometry and Weldon shank for rigid, vibration‑free machining; order directly via Metav Werkzeuge or contact the consultants for application guidance.

TECWERK Full‑radius milling cutter D 2 mm, HSS‑Co8, TiCN, Weldon shank

A TECWERK full‑radius milling cutter D 2 mm designed for short‑reach profiling and finishing tasks in demanding steel and cast‑iron machining environments.

• HSS‑Co8 substrate with TiCN coating
• 2 cutting edges, centre‑cutting design
• Weldon shank with drive flat for secure clamping
• Extra‑short geometry for rigid, accurate cuts

Rigid, compact design for stable micro‑milling

The combination of an HSS‑Co8 substrate with a TiCN surface finish gives the cutter a balance of toughness and surface hardness that suits interrupted and continuous cuts in tough materials. With a nominal diameter of 2 mm and an effective length of 10 mm, the extra‑short geometry minimises overhang and reduces deflection, which translates into improved dimensional accuracy and lower scrap rates when machining small features. The Weldon shank provides a positive drive interface, ensuring the cutter remains secure in the collet under higher feed forces.

Optimised for steel and cast‑iron production tasks

Designed for production environments where throughput and repeatability matter, the tool is very well suited to steel and cast‑iron components while offering conditional performance in non‑ferrous metals, stainless alloys and special high‑strength materials. The centre‑cutting capability allows controlled plunge operations as well as peripheral milling, reducing the need for tool changes and setup adjustments in compact fixtures. Right‑hand cutting geometry supports conventional milling strategies commonly used on CNC vertical and horizontal machines.

Secure clamping and sustained tool life

The cylindrical shank with a drive flat ensures consistent seating and torque transmission, reducing the risk of slippage in high‑load passes. The TiCN coating lowers friction, improves wear resistance and helps prevent built‑up edge in typical steel machining, contributing to longer tool life and more stable surface finish. With 2 flutes, chip evacuation is effective in short‑axial engagements, which helps to maintain cutting stability and reduces heat accumulation in tight cavities.

Practical applications and machining advice

Ideal applications include fine profiling, pocket finishing and small‑feature machining where rigidity and surface quality are priorities. The tool performs best in rigid setups with minimal stick‑out; cutters with this geometry are particularly effective for work on compact castings, turned components requiring tight radii, and fixtures where access is restricted. For feeds and speeds adapted to specific alloys and machine capabilities, consult Metav Werkzeuge for tailored parameter recommendations and to ensure maximum efficiency and tool life.

For precision short‑reach milling select the TECWERK full‑radius cutter and contact Metav Werkzeuge in Emmerich for application support and rapid supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for technical advice and ordering.

Technical data

• Article number: 2000866594NW
• Label: Vollradiusfräser D.2mm Einsatz-L.10mm HSS-Co8 TiCN Weldon Z.2 ext.kurz TECWERK
• Manufacturer: TECWERK

Facts

• Diameter: 2 mm
• Radius: 1 mm
• Overall length: 48 mm
• Effective length: 10 mm
• Cutting length: 2 mm
• Shank diameter: 6 mm
• Number of cutting edges: 2
• Cutting direction: right‑hand

Special features

• Material: HSS‑Co (HSS‑Co8)
• Coating: TiCN
• Centre‑cutting design
• Weldon shank with drive flat
• Extra‑short geometry
• Cylindrical shank with drive flat
• Suited to steel: very well suited
• Suited to cast iron: very well suited
• Suited to non‑ferrous metals: conditionally suitable
• Suited to special alloys and stainless: conditionally suitable

FAQ

What materials is this cutter best suited to?
The TECWERK full‑radius milling cutter D 2 mm is very well suited to steel and cast‑iron work and is conditionally suitable for non‑ferrous metals, special alloys and stainless applications.

Can the cutter perform plunge cuts?
Yes, the centre‑cutting geometry allows plunge operations as well as peripheral milling, which is useful for slotting and pocket starts.

How does the Weldon shank benefit machining stability?
The Weldon shank with drive flat secures the tool in the holder and prevents rotation or slippage under higher feed forces, contributing to consistent dimensional results.

What chip evacuation behaviour can be expected?
With 2 flutes the cutter offers efficient chip evacuation in short engagements, helping to reduce heat build‑up and maintain cutting stability in compact features.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund