Combine the TiCN coating with HSS‑Co8 construction and the R5 full‑radius profile for robust finishing and long tool life; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK full‑radius end mill D10 mm — HSS‑Co8, TiCN, Weldon The TECWERK full‑radius end mill D10 mm is an extra‑short, centre‑cutting radius cutter for precise machining of steel and cast components in compact, rigid set‑ups. Extra‑short 2‑flute geometry for rigid set‑ups TiCN coating for increased wear resistance HSS‑Co8 material for high toughness and heat resistance Weldon shank with drive flat for secure clamping High‑performance finishing for steel and cast parts Manufactured for demanding finishing operations, this radius cutter combines a R5 full‑radius profile with HSS‑Co8 base material to deliver consistent corner geometry and improved edge strength. The 10 mm diameter and 21 mm effective length are optimised for short‑span milling where rigidity and repeatable results matter. For components up to approximately 1200 N/mm² tensile strength, the tool offers reliable material removal with reduced risk of chipping, making it particularly suited to fine machining of steel and cast iron components. Coating and substrate: why TiCN on HSS‑Co8 works The combination of a TiCN coating on an HSS‑Co8 substrate increases surface hardness and thermal resistance without sacrificing the substrate’s inherent toughness. This means longer tool life under intermittent cutting and better resistance to built‑up edge. The two‑flute geometry supports efficient chip evacuation and stable cutting forces, while the centre‑cutting design allows plunge and profile milling. For users with limited tool change windows, the coating‑substrate pairing reduces downtime and contributes to a more economical production rhythm. Rigidity, clamping and handling in compact setups Designed as an extra‑short tool with a Weldon shank and drive flat, this cutter prioritises secure clamping and minimal overhang. That rigidity translates directly into improved surface finish and dimensional consistency when working in tight fixtures or small milling heads. The reduced effective projection lowers vibration susceptibility, so set‑ups that demand repeatable radiused contours benefit from fewer rejects and faster set‑up verification. The relief grind of 9.5 mm supports clearance during radial engagement and simplifies fixture alignment. Practical applications and machining advice This full‑radius end mill excels in finishing radiused pockets, fillets and die features where a precise corner radius is required. The two‑flute layout is advantageous for steels and cast materials, while non‑ferrous and special alloys are machinable with moderated parameters. Being right‑hand cutting and centre‑cutting, the cutter permits plunge starts and conventional profiling. When calculating feeds and speeds, prioritise rigidity and coolant strategy to exploit the TiCN wear resistance; shorter axial depths and stable RPMs prolong tool life and enhance surface integrity. For supply of TECWERK full‑radius end mills and tailored application recommendations based on TiCN‑coated HSS‑Co8 geometry, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for direct procurement and expert consultancy. Technical Data Article number: 2000866606NW Manufacturer: TECWERK Facts Diameter: 10 mm Overall length: 63 mm Effective length: 21 mm Cutting length: 2 mm Shank diameter: 10 mm Radius: 5 mm Number of flutes: 2 Relief grind: 9,5 mm Special features Material: HSS‑Co8 Coating: TiCN Centre‑cutting Weldon shank with drive flat Extra short design Right‑hand cutting Very good suitability for steel Very good suitability for cast iron Conditional suitability for non‑ferrous metals, special alloys and inox FAQ What materials is this cutter best suited for? The cutter is very well suited for steel and cast iron applications; non‑ferrous metals, special alloys and stainless steels are machinable with adjusted parameters for the TiCN‑coated HSS‑Co8 tool. Can the tool be used for plunge milling? Yes. The centre‑cutting geometry allows plunge starts and makes the cutter suitable for profile and pocketing tasks where a radiused corner is required. How does the TiCN coating affect performance? The TiCN coating increases surface hardness and thermal resistance, improving wear life and reducing built‑up edge compared with uncoated HSS tools. What size and shank specifications does the tool have? The cutter has a 10 mm diameter, 10 mm shank and a Weldon shank with drive flat to ensure secure clamping in rigid fixtures. Which SKU identifies this tool for ordering? Refer to SKU 2000866606NW when ordering the TECWERK full‑radius end mill to ensure the correct specification is supplied. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of solid carbide construction, TiAlN surface protection and a short, rigid design for consistent high‑feed performance; order directly via Metav Werkzeuge or consult the team for tailored application advice. Full‑Radius End Mill D10 mm, Effective Length 24 mm (TECWERK) — TiAlN‑coated, 2‑flute short version The Full‑Radius End Mill D10 mm, Effective Length 24 mm is a short, centre‑cutting solid carbide cutter designed for precision milling of steels, cast iron and a wide range of non‑ferrous materials Solid carbide, fine-grain construction TiAlN coating for high temperature stability Centre-cutting for plunge operations Cylindrical shank to DIN 6535 HB Precision and reliability for demanding machining The combination of solid carbide substrate and a TiAlN coating delivers sustained cutting performance and improved tool life in interrupted and continuous cuts. With a 10 mm diameter and effective length 24 mm, the tool balances reach and rigidity to reduce chatter and maintain dimensional accuracy. The full‑radius geometry (radius 5 mm) provides a consistent profile for contouring and corner radii, while the short overall length increases stability for higher feed rates and deeper passes where stiffness matters. Efficient chip evacuation and thermal resistance The two‑flute geometry promotes efficient chip evacuation, which is beneficial when machining sticky or abrasive materials such as aluminium alloys with silicon content and certain plastics. The TiAlN layer enhances heat resistance and reduces adhesion, so cutting edges retain sharpness for longer and heat‑related wear is minimised. The centre‑cutting capability allows safe plunge operations, turning a profile cutter into a versatile tool for stepdowns and pocketing without changing tooling strategy. Seamless integration into workshop setups Designed with a cylindrical shank to DIN 6535 HB and a shank tolerance of h6, this cutter fits standard toolholders reliably and simplifies tool changeover. The 30° helix angle and right‑hand cutting direction are optimised for general‑purpose milling across steel, cast iron, stainless, non‑ferrous metals and special alloys, reducing the need for multiple tool variants. For operations where consistent quality and supply matter, the short version offers a practical compromise between performance and cost efficiency. Choose the TECWERK TiAlN‑coated full‑radius end mill for dependable, high‑productivity milling — contact Metav Werkzeuge in Emmerich for application guidance or to arrange supply: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: 2000866975NW Label: Vollradiusfräser D.10mm Einsatz-L.24mm VHM TiAlN HB Z.2 kurz TECWERK Product type: Full‑radius end mill Manufacturer: TECWERK Facts Diameter: 10 mm Effective length: 24 mm Overall length: 66 mm Shank diameter: 10 mm Radius: 5 mm Flutes: 2 Clearance (freeschliff): 9.7 mm Helix angle: 30° Cutting direction: Right‑hand Shank tolerance: h6 Special features Solid carbide, fine‑grain TiAlN coating Centre‑cutting (plunge capable) Cylindrical shank to DIN 6535 HB Short version for increased stiffness Suitable for steel, cast iron, stainless steel, non‑ferrous metals, special alloys Suitable for aluminium with silicon and abrasive plastics Two cutting edges, type N, factory standard FAQ Which materials is this cutter suitable for? The cutter is suitable for steel, cast iron, stainless steel, non‑ferrous metals and special alloys, as specified for the TECWERK full‑radius end mill (SKU 2000866975NW). Can the tool be used for plunge cuts? Yes, the tool features centre‑cutting geometry, allowing safe plunge operations in addition to conventional milling. What shank specification does the cutter use? The cutter is supplied with a cylindrical shank to DIN 6535 HB and a shank tolerance of h6, ensuring secure seating in standard holders. How does the TiAlN coating benefit production? The TiAlN coating increases high‑temperature stability and wear resistance, reducing edge wear and improving tool life under higher cutting temperatures. Is this cutter suitable for aluminium with silicon content? Yes, the product data lists suitability for aluminium with silicon content and abrasive plastics, supported by the tool’s two‑flute geometry and coating. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of compact rigidity, durable TiCN protection and cobalt-enriched HSS for consistent short-reach milling performance. Take advantage of improved chip evacuation from the two-flute geometry and the centre-cutting capability for plunge operations. Order the tool directly via Metav Werkzeuge or ask our consultants for application advice. TECWERK full-radius end mill Ø12 mm — HSS-Co8, TiCN, Weldon shank The TECWERK full-radius end mill Ø12 mm is an extra-short, two-flute milling cutter with TiCN coating and a Weldon shank, engineered for precision milling, plunge cuts and reliable performance in steel and cast iron. HSS-Co8 base for high-temperature stability TiCN coating for extended wear resistance Extra-short, rigid two-flute design Centre-cutting for plunge and ramp milling Rigidity and precision for short-reach machining The tool’s extra-short geometry and Ø12 mm body yield high stiffness, reducing deflection during interrupted cuts and short-reach slotting. With an effective length of 26 mm and a compact overall length, the reduced overhang increases positional accuracy and repeatability, which directly benefits cycle-time consistency in small-batch or precision components. The R6 full-radius profile gives a larger contact zone than a sharp corner, improving surface finish and extending tool life where fillet radii are required. Durable construction that keeps tools in production Manufactured from HSS-Co8 (cobalt-alloyed high-speed steel) and finished with a TiCN coating, the cutter offers elevated hardness and improved heat resistance compared with uncoated HSS. The coating reduces adhesive wear and supports higher cutting temperatures, which is advantageous when machining materials with tensile strengths up to approximately 1200 N/mm². Material suitability is optimised for steel and cast iron (very good), while non-ferrous metals, special alloys and stainless steels are conditionally machinable, depending on cutting data and coolant strategy. Geometry and interface designed for workshop reliability The two-flute configuration balances chip evacuation and cutting edge strength, making it well suited for slotting and side milling in constrained setups. The cutter is centre-cutting, enabling safe plunge operations and simple ramping strategies without additional tooling. A Weldon shank with drive flat ensures secure clamping in holders and prevents slippage under high torque, while the right-hand cutting direction matches standard machine tool conventions. These design choices reduce setup time and integrate easily into existing tool lists. For procurement or detailed application advice on TECWERK full-radius end mills, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for fast, expert support and supply. Technical data Article number: 2000866608NW Designation: Full-radius end mill Ø12 mm, HSS-Co8, TiCN, Weldon shank Manufacturer: TECWERK Facts Diameter: 12 mm Radius: 6 mm Overall length: 73 mm Effective length: 26 mm Cutting length: 2 mm Relief length: 11.5 mm Number of flutes: 2 Shank diameter: 12 mm Special features Material: HSS-Co8 Coating: TiCN Centre-cutting Weldon shank with drive flat Right-hand cut Extra-short version Very good suitability for steel Very good suitability for cast iron Conditional suitability for non-ferrous metals, special alloys and stainless steel For materials up to approx. 1200 N/mm² tensile strength FAQ Is this cutter suitable for plunge milling? The TECWERK full-radius end mill is centre-cutting, so it is suitable for plunge milling and controlled ramp entries when using appropriate feeds and coolant. Which materials work best with this tool? The tool is optimised for steel and cast iron (very good). Non-ferrous metals, special alloys and stainless steel are conditionally suitable depending on cutting data. What does the TiCN coating provide? The TiCN coating increases surface hardness and reduces adhesive wear, extending service life and allowing higher thermal loads compared with uncoated HSS tools. How is the cutter clamped in the tool holder? The cutter features a Weldon shank with drive flat for secure clamping and reliable torque transmission in standard holders. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from the combination of HSS‑Co8 toughness, TiCN surface protection and a secure Weldon shank for reliable, vibration‑resistant milling; order the full‑radius end mill (TECWERK 2000866612NW) directly via Metav Werkzeuge or ask our consultants if needed. TECWERK full‑radius end mill D16 mm — HSS‑Co8, TiCN, Weldon The TECWERK full‑radius end mill D16 mm is an extra‑short, centre‑cutting milling tool designed for rigid machining of steel and cast workpieces in demanding production environments HSS‑Co8 base material for heat resistance TiCN coating for increased wear resistance Weldon shank for positive drive Extra‑short design for maximum rigidity Faster, more consistent metal removal with cobalt‑alloy steel The tool combines HSS‑Co8 substrate hardness with a TiCN coating to reduce friction and extend tool life during continuous milling. The 2‑flute geometry supports efficient chip evacuation while the centre‑cutting geometry allows controlled plunging operations. As a result, milling cycles become more predictable and process capability is improved, particularly where repeated contouring and pocketing of ferrous components is required. Secure clamping and improved runout control for repeatable accuracy A Weldon shank with drive flat and a 16 mm shank diameter provide a positive, slip‑free interface in most toolholders, supporting stable torque transmission and minimising runout. The tool’s effective length of 29 mm together with an extra‑short overall length reduces overhang and increases stiffness, delivering better surface finish and dimensional consistency on series parts where tight tolerances matter. Clear guidance on suitable applications and materials Designed primarily for machining steel and cast components, the cutter is rated for workpiece strengths up to approx. 1200 N/mm². Performance in non‑ferrous metals, special alloys and stainless steel is conditional; the combination of substrate and coating is optimised for steels and castings, where heat resistance and wear control are decisive. The geometry and coating support roughing and semi‑finishing tasks where both material removal and tool life are priorities. Practical handling to extend service life and maintain productivity To get the most from the tool, ensure firm clamping and minimise overhang to exploit the inherent rigidity of the short design. The TiCN layer helps against abrasive wear and built‑up edge, while the cobalt alloy maintains hardness at elevated temperatures; appropriate use of coolant and stable fixturing will further extend tool life. Regular inspection of clamping surfaces and the Weldon flat keeps runout low and repeatability high in production runs. Contact Metav Werkzeuge today to discuss the TECWERK full‑radius end mill (SKU 2000866612NW) and secure the right solution for the workshop — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000866612NW Product: Full‑radius end mill D16 mm (TECWERK) Manufacturer: TECWERK Facts Diameter: 16 mm Corner radius: 8 mm Effective length: 29 mm Overall length: 79 mm Shank diameter: 16 mm Cutting edges: 2 Relief (freischliff): 15 mm Special features Material: HSS‑Co (HSS‑Co8) Coating: TiCN Weldon shank (cylindrical shank with drive flat) Centre cutting Right‑hand cutting Extra‑short design Suitable for steels up to approx. 1200 N/mm² Very good for steel and cast; conditionally suitable for non‑ferrous metals, special alloys and stainless steel FAQ What materials can be machined reliably with this cutter? The TECWERK full‑radius end mill is very well suited to steel and cast components and is specified for workpiece strengths up to approximately 1200 N/mm²; performance in non‑ferrous metals, special alloys and stainless steel is conditional. Is this tool suitable for plunge cutting? Yes. The tool’s centre‑cutting geometry permits controlled plunging, enabling shorter setups for pocketing or when axial entry is required. How does the TiCN coating benefit production use? The TiCN coating lowers friction and improves wear resistance compared with uncoated high‑speed steel, which helps maintain cutting edge integrity and reduces downtime for tool changes in longer production runs. Which shank type is used and why does it matter? A Weldon shank with drive flat is provided to ensure a positive, slip‑free connection in the toolholder; this improves torque transmission and reduces runout for better repeatability. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a solid-carbide design combined with a TiAlN coating and a 30° helix to deliver durable, high-performance milling with reliable chip control; order the cutter directly via Metav Werkzeuge or consult our specialists for machining recommendations. TECWERK full-radius end mill D16 mm – solid carbide, TiAlN-coated, R8 mm The TECWERK full-radius end mill D16 mm is a short, centre-cut solid-carbide tool designed for high-demand milling of steel, cast iron and non-ferrous materials in workshop and industrial applications Solid carbide body with TiAlN coating 2-flute geometry for efficient chip evacuation 30° helix for smooth cutting Cylindrical shank to DIN 6535 HB, h6 tolerance Durable construction for extended tool life and stable machining The combination of a solid carbide substrate and TiAlN coating forms a hard, heat-resistant cutting edge that extends tool life under continuous operation. The coating reduces adhesion and thermal wear, which translates into longer intervals between regrinds and fewer tool changes on the production floor. This robust build supports high-speed machining and keeps dimensional stability over repeated cycles, helping to maintain consistent part quality in batch production. Geometry engineered for controlled chips and improved surface finish A 2-flute geometry paired with a 30° helix promotes efficient chip evacuation and reduces cutting forces, resulting in smoother feeds and an improved surface finish on workpieces. The cutter features centre-cutting capability so it can plunge as well as profile, while its effective length 32 mm and short overall design reduce vibration and deflection. These characteristics make the tool well suited to pocketing, shoulder milling and contouring operations where tight tolerances and clean edges are required. Broad material suitability and straightforward integration into existing setups This tool is optimised for a wide range of materials: steel, stainless steel, cast iron and non-ferrous metals such as bronze and brass, as well as aluminium alloys with silicon content and certain abrasive plastics. The full-radius geometry (R8 mm) delivers rounded contouring for fillets and smooth transitions. The cylindrical shank to DIN 6535 HB with h6 tolerance ensures concentricity in standard tool holders, enabling quick integration into CNC spindles and decreased setup time at the machine. Contact Metav Werkzeuge for expert advice on integrating this TECWERK full-radius cutter into production and secure delivery from our Emmerich warehouse. Technical data Article number: 2000866978NW Label: Vollradiusfräser D.16mm Einsatz-L.32mm VHM TiAlN HB Z.2 kurz TECWERK Brand: TECWERK Data Diameter: 16 mm Radius: 8 mm Effective length: 32 mm Overall length: 82 mm Shank diameter: 16 mm Cutting length: 2 mm Number of flutes: 2 Helix angle: 30° Free clearance (neck relief): 15.5 mm Cutting direction: right-hand Shank tolerance: h6 Special features Material: solid carbide (VHM) Coating: TiAlN Centre-cutting geometry Short design for reduced deflection Cylindrical shank to DIN 6535 HB Very well suited for steel, cast iron, INOX and non-ferrous metals Suitable for special alloys and abrasive plastics FAQ What materials is this cutter suitable for? The TECWERK full-radius end mill (SKU 2000866978NW) is very well suited for steel, stainless steel, cast iron, non-ferrous metals and certain abrasive plastics, offering broad application flexibility. Can the tool perform plunge cuts and contouring? Yes. The tool’s centre-cutting design allows plunge cutting as well as profiling and contouring, making it suitable for pocketing and fillet work. How does the TiAlN coating benefit production? The TiAlN coating increases thermal resistance and reduces edge wear, which extends tool life and supports higher cutting speeds in repetitive production tasks. What tolerance and shank standard ensure compatibility with holders? The cutter has a cylindrical shank to DIN 6535 HB with h6 tolerance, providing concentricity and compatibility with standard tool holders. What is the effective cutting length and why does it matter? The effective length is 32 mm, which balances reach with rigidity; this reduces deflection compared with longer tools and improves dimensional accuracy. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of solid carbide construction, TiAlN heat protection and a short, rigid geometry to maintain stable, high-precision milling in demanding workshop environments — order the tool via Metav Werkzeuge or ask their consultants for tailored technical advice. TECWERK Full-radius end mill Ø20 mm, TiAlN-coated, VHM, 2 flutes The TECWERK Full-radius end mill Ø20 mm is a short, centre-cutting solid carbide mill designed for precise face and contour milling across steels, cast iron and non‑ferrous alloys Solid carbide, fine-grain VHM TiAlN coating for heat resistance Centre-cutting for plunging 30° helix, two-flute short version Consistent metal-removal with increased thermal resistance The combination of solid carbide construction and a TiAlN coating provides a high-hardness cutting edge and improved oxidation resistance under elevated temperatures, which translates into longer tool life and fewer tool changes. The two‑flute geometry promotes freer chip evacuation in interrupted cuts, while the 30° helix balances cutting forces and surface finish. These design choices result in predictable material removal rates and reduced downtime for production runs. Rigidity and accuracy for shoulder work and shallow pockets The short design with a 20 mm shank and effective length 40 mm gives high torsional stiffness and reduced deflection compared with longer tools, improving dimensional accuracy on shoulders and tight tolerances. The cylindrical shank conforms to DIN 6535 HB with a h6 tolerance for secure clamping and concentricity in standard toolholders. The centre‑cutting geometry permits controlled plunging, enabling efficient internal entrances without the need for pre‑drilling. One tool for a wide range of materials saves preparation time This tool demonstrates very good suitability for a broad spectrum of workpieces: steel, cast iron, stainless (CrNi) steels, bronze, brass, copper, aluminium with silicon and abrasive engineering plastics. The specification is aimed at reducing tool variety in the workshop by offering a single cutter capable of handling different materials with reliable performance, provided the cutting data are adapted to each material class and machine capability. Practical workshop benefits and handling tips The short, two‑flute layout and centre‑cutting tip of the TECWERK full‑radius cutter make it particularly suited to operations where rigidity, plunge ability and chip control are priorities. The tool’s fine‑grain VHM substrate maintains edge integrity under moderate climb and conventional milling directions (right‑hand cutting), and the 30° helix supports good surface quality. For best results, use appropriate coolant and adjust feeds and speeds to the workpiece material and machine rigidity. For reliable workshop performance, select the TECWERK full‑radius end mill via Metav Werkzeuge — technical advice and fast supply are available from Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000866991NW Label: Vollradiusfräser D.20mm Einsatz-L.40mm VHM TiAlN HB Z.2 kurz TECWERK Manufacturer: TECWERK Facts Diameter: 20 mm Effective length: 40 mm Total length: 92 mm Shank diameter: 20 mm Radius: 10 mm Number of flutes: 2 Helix angle: 30° Shank tolerance: h6 Special features Material: solid carbide (VHM) fine-grain Coating: TiAlN Centre-cutting (plunge capable) Cylindrical shank to DIN 6535 HB Short type for high rigidity Right-hand cutting Very good suitability: steel, non‑ferrous metals, special alloys, INOX, cast Type N, two‑cutters, factory standard FAQ Which materials is this cutter suitable for? The TECWERK full‑radius end mill is specified for steel, cast iron, stainless (CrNi) steels, bronze, brass, copper, aluminium with silicon content and abrasive plastics, delivering versatile performance across these material groups. Can this tool be used for plunge cutting? Yes, the centre‑cutting design enables controlled plunging into the material, so the cutter can perform short axial entries as well as conventional peripheral milling. What are the shank standard and tolerance? The tool features a cylindrical shank to DIN 6535 HB with a h6 tolerance and a shank diameter of 20 mm, suitable for standard toolholders that accept DIN 6535 HB shanks. What advantages does the TiAlN coating provide? The TiAlN coating increases surface hardness and resistance to oxidation at high temperatures, which helps maintain cutting-edge integrity and extends tool lifetime during machining of harder alloys. Is this cutter appropriate for machining aluminium? The specification lists suitability for aluminium with silicon content; adequate chip evacuation and appropriate cutting data are important to avoid built‑up edge and to achieve a good surface finish. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the tool's combination of HSS‑Co8 core and TiCN coating for extended life, together with the extra‑short geometry and Weldon shank for rigid, vibration‑free machining; order directly via Metav Werkzeuge or contact the consultants for application guidance. TECWERK Full‑radius milling cutter D 2 mm, HSS‑Co8, TiCN, Weldon shank A TECWERK full‑radius milling cutter D 2 mm designed for short‑reach profiling and finishing tasks in demanding steel and cast‑iron machining environments. HSS‑Co8 substrate with TiCN coating 2 cutting edges, centre‑cutting design Weldon shank with drive flat for secure clamping Extra‑short geometry for rigid, accurate cuts Rigid, compact design for stable micro‑milling The combination of an HSS‑Co8 substrate with a TiCN surface finish gives the cutter a balance of toughness and surface hardness that suits interrupted and continuous cuts in tough materials. With a nominal diameter of 2 mm and an effective length of 10 mm, the extra‑short geometry minimises overhang and reduces deflection, which translates into improved dimensional accuracy and lower scrap rates when machining small features. The Weldon shank provides a positive drive interface, ensuring the cutter remains secure in the collet under higher feed forces. Optimised for steel and cast‑iron production tasks Designed for production environments where throughput and repeatability matter, the tool is very well suited to steel and cast‑iron components while offering conditional performance in non‑ferrous metals, stainless alloys and special high‑strength materials. The centre‑cutting capability allows controlled plunge operations as well as peripheral milling, reducing the need for tool changes and setup adjustments in compact fixtures. Right‑hand cutting geometry supports conventional milling strategies commonly used on CNC vertical and horizontal machines. Secure clamping and sustained tool life The cylindrical shank with a drive flat ensures consistent seating and torque transmission, reducing the risk of slippage in high‑load passes. The TiCN coating lowers friction, improves wear resistance and helps prevent built‑up edge in typical steel machining, contributing to longer tool life and more stable surface finish. With 2 flutes, chip evacuation is effective in short‑axial engagements, which helps to maintain cutting stability and reduces heat accumulation in tight cavities. Practical applications and machining advice Ideal applications include fine profiling, pocket finishing and small‑feature machining where rigidity and surface quality are priorities. The tool performs best in rigid setups with minimal stick‑out; cutters with this geometry are particularly effective for work on compact castings, turned components requiring tight radii, and fixtures where access is restricted. For feeds and speeds adapted to specific alloys and machine capabilities, consult Metav Werkzeuge for tailored parameter recommendations and to ensure maximum efficiency and tool life. For precision short‑reach milling select the TECWERK full‑radius cutter and contact Metav Werkzeuge in Emmerich for application support and rapid supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for technical advice and ordering. Technical data Article number: 2000866594NW Label: Vollradiusfräser D.2mm Einsatz-L.10mm HSS-Co8 TiCN Weldon Z.2 ext.kurz TECWERK Manufacturer: TECWERK Facts Diameter: 2 mm Radius: 1 mm Overall length: 48 mm Effective length: 10 mm Cutting length: 2 mm Shank diameter: 6 mm Number of cutting edges: 2 Cutting direction: right‑hand Special features Material: HSS‑Co (HSS‑Co8) Coating: TiCN Centre‑cutting design Weldon shank with drive flat Extra‑short geometry Cylindrical shank with drive flat Suited to steel: very well suited Suited to cast iron: very well suited Suited to non‑ferrous metals: conditionally suitable Suited to special alloys and stainless: conditionally suitable FAQ What materials is this cutter best suited to? The TECWERK full‑radius milling cutter D 2 mm is very well suited to steel and cast‑iron work and is conditionally suitable for non‑ferrous metals, special alloys and stainless applications. Can the cutter perform plunge cuts? Yes, the centre‑cutting geometry allows plunge operations as well as peripheral milling, which is useful for slotting and pocket starts. How does the Weldon shank benefit machining stability? The Weldon shank with drive flat secures the tool in the holder and prevents rotation or slippage under higher feed forces, contributing to consistent dimensional results. What chip evacuation behaviour can be expected? With 2 flutes the cutter offers efficient chip evacuation in short engagements, helping to reduce heat build‑up and maintain cutting stability in compact features. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of precision, robust TiAlN protection and a short, centre-cutting geometry for reliable small-diameter milling. Order directly via Metav Werkzeuge or consult the technical team for application-specific advice. Full-radius end mill D3 mm, solid carbide (VHM), TiAlN — TECWERK The Full-radius end mill D3 mm is a short, centre-cutting solid-carbide cutter designed for precision milling of steel, cast iron and non-ferrous materials in workshop and production environments. Solid carbide (VHM) with TiAlN coating Short, centre-cutting design with 30° helix Very good for steel and stainless steel processing Cylindrical shank 6 mm to DIN 6535 HB Precision for confined geometries and repeatable results The short, centre-cutting geometry ensures secure plunging and immediate engagement in confined features. With a 3 mm nominal diameter and 1.5 mm full radius, the tool is optimised for contour finishing and fillet work where dimensional accuracy matters. The combination of a solid-carbide substrate and a TiAlN surface layer reduces flank wear and maintains cutting edge integrity, which translates into consistent part tolerances and fewer rejects in serial production. Broad material suitability reduces tool changes Engineered as a universal fine-grain carbide tool, this cutter is rated very good for a wide range of materials: unalloyed and alloyed steels, stainless (INOX), cast irons, bronzes, brass, copper and aluminium alloys containing silicon, plus abrasive plastics. The versatile material compatibility minimises tool swapping on mixed-production benches, improving throughput and reducing machine downtime. The TiAlN coating additionally supports high-temperature strength for sustained cutting in tougher alloys. Geometry and coating that boost productivity The 30° helix and two-flute layout promote efficient chip evacuation while maintaining axial stability; this is particularly helpful when working with small diameters where chip control is critical. The centre-cutting configuration enables plunge cuts and pocket entries without a separate drill operation. TiAlN coating offers enhanced oxidative resistance and heat hardness, extending tool life under elevated cutting temperatures—resulting in longer intervals between regrinds or replacements and a more economical machining process. Compatibility, handling and set-up for workshop use A 6 mm cylindrical shank to DIN 6535 HB with h6 tolerance ensures secure clamping in standard collets, facilitating quick tool changes and repeatable concentricity. The useful overall length of 50 mm and effective cutting length of 9 mm provide working reach while keeping tool deflection low. Short tools require less radial runout and therefore produce better surface finishes; together with correct speeds and feeds, this cutter supports high-quality results even in manual and CNC setups. For machining strategies and feed-rate guidance, Metav Werkzeuge’s technical advisors can provide tailored recommendations. Contact Metav Werkzeuge today for reliable supply of TECWERK solid-carbide cutters and expert guidance from our Emmerich quality filter — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 Technical data Article number: 2000866929NW Label: Full-radius end mill D3 mm, effective length 9 mm, VHM, TiAlN, 2 flutes, short — TECWERK Manufacturer: TECWERK Core data Diameter: 3 mm Radius: 1.5 mm Effective length: 9 mm Cutting length: 2 mm Overall length: 50 mm Shank diameter: 6 mm Number of flutes: 2 Helix angle: 30° Cutting direction: right-hand Coating: TiAlN Materials & special features Material: solid carbide (universal fine-grain) Centre-cutting design Two-flute, short version Cylindrical shank to DIN 6535 HB, tolerance h6 Factory standard, Type N Very good for steel, stainless steel (INOX), cast iron Suitable for bronze, brass, copper, aluminium with silicon, abrasive plastics Designed for reliable chip evacuation and low deflection FAQ What materials can be machined with this cutter? The Full-radius end mill D3 mm (TECWERK) is suitable for steel, stainless steel, cast irons, bronzes, brass, copper and aluminium alloys with silicon, as well as abrasive plastics. Is the tool suitable for plunging and slotting operations? Yes, the centre-cutting, short design allows safe plunging and slotting; the two-flute geometry aids chip evacuation during such operations. What shank and clamping should be used for best rigidity? Use a 6 mm collet compliant with DIN 6535 HB and h6 tolerance to ensure concentric clamping and minimal runout for optimal surface finish. How does the TiAlN coating benefit production? TiAlN increases thermal resistance and edge hardness at elevated temperatures, reducing wear and extending tool life under demanding cutting conditions. Can this cutter be used on CNC milling machines and manual machines? Yes, the cutter’s short length and robust geometry make it suitable for both CNC and manual milling setups when correct speeds and feeds are applied. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combine precision, durability and a compact short design to maintain productive machining with fewer tool changes. Benefit from the solid carbide construction and TiAlN coating for extended tool life and consistent surface quality. Order the cutter directly via Metav Werkzeuge or contact our consultants for application advice. TECWERK Full-radius end mill D 4 mm — solid carbide, TiAlN-coated, 2 flutes TECWERK Full-radius end mill D 4 mm is a short, centre-cutting solid carbide radius cutter engineered for precision finishing and plunge-capable slotting in steels, castings and non-ferrous alloys. TiAlN coating for high wear resistance Solid carbide, universal fine grain Centre-cutting for plunge capability Short version for increased rigidity High-precision machining of small features and edges The 4 mm diameter profile with an integrated R2 radius delivers repeatable edge contours and reduced deburring across batches. With an effective length 12 mm and 2 flutes, the tool provides a balance between cutting engagement and chip evacuation that supports consistent surface quality in tight geometries. The centre-cutting geometry enables plunge operations while the short design reduces overhang, resulting in improved stability and fewer rejected parts. Coating and substrate for extended cutting cycles The combination of solid carbide substrate and TiAlN coating raises resistance to elevated temperatures and abrasive wear, extending uninterrupted running times on demanding jobs. The coating helps maintain cutting-edge integrity, which translates into high wear resistance and longer tool life under mixed cutting conditions. Fewer tool changes mean lower machine downtime and a better cost profile per produced part. One tool for a wide range of materials Designed for versatile workshop use, the cutter is very well suited to steel, cast iron, stainless steel, aluminium with silicon, and many non-ferrous metals such as bronze and brass, as well as abrasive plastics. This broad material compatibility reduces tool inventories and simplifies setup planning, enabling faster changeovers and fewer sourcing decisions for mixed-production environments. Rigidity, clamping and reliable machine integration The cylindrical shank to DIN 6535 HB with a 6 mm shank diameter and h6 shank tolerance ensures secure clamping in standard holders and collets, while the 30° helix and right-hand cutting geometry promote smooth chip formation. The short overall length and centre-cutting capability increase rigidity for plunge and slotting tasks, lowering the risk of chatter and improving dimensional stability in serial production. For tailored process recommendations or to request the TECWERK full-radius end mill for specific applications, contact Metav Werkzeuge for fast supply from Emmerich — eMail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data SKU: 2000866971NW Label: Vollradiusfräser D.4mm Einsatz-L.12mm VHM TiAlN HB Z.2 kurz Manufacturer: TECWERK Core dimensions Diameter: 4 mm Radius: 2 mm Overall length: 54 mm Effective length: 12 mm Cutting length: 2 mm Shank diameter: 6 mm Number of flutes: 2 Helix angle: 30° Relief grind: 3.8 mm Special features Material: solid carbide Coating: TiAlN Centre-cutting geometry Shank per DIN 6535 HB Shank tolerance: h6 Right-hand cutting Short version for increased rigidity Suitable for steel, cast iron, stainless, aluminium (with silicon), bronze, brass, abrasive plastics FAQ Which materials can this cutter machine effectively? The TECWERK full-radius end mill is very well suited to steel, cast iron, stainless steels, aluminium with silicon, bronze, brass and certain abrasive plastics, offering broad versatility across workshops. Does the tool allow plunge cutting and slotting? Yes, the centre-cutting geometry permits plunge operations and short slotting tasks while the short overall design improves rigidity for stable machining. What benefits does the TiAlN coating provide? The TiAlN coating increases heat and wear resistance, which helps extend the cutter’s useful life and maintain consistent cutting performance in tougher operations. What shank size and tolerance should the clamping system accept? Use a holder or collet compatible with a 6 mm shank and h6 tolerance; the DIN 6535 HB cylindrical shank ensures secure clamping for productive runs. Can the cutter be used across serial production and prototypes? Yes — the tool’s combination of solid carbide substrate, coating and short geometry makes it suitable for both serial production and precision prototyping; SKU 2000866971NW identifies the short full-radius version. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of high rigidity, TiCN wear resistance and centre-cutting capability to maintain precise milling in steel and cast iron; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK full-radius end mill D 4 mm, HSS-Co8, TiCN, Weldon shank — extra-short, 2-flute centre-cutting tool The TECWERK full-radius end mill D 4 mm is a compact, centre-cutting cutter for precision radius milling and short-reach profiling in steel and cast iron applications Extra-short design for maximum rigidity TiCN coating for enhanced wear resistance Centre-cutting for safe plunge milling Weldon shank with drive flat for secure clamping Rigidity and repeatable precision for short-reach milling The extra-short design delivers high stiffness, reducing deflection during aggressive passes and enabling repeatable results in finishing and semi-finishing operations. With a 4 mm diameter and a 2 mm radius, the tool is optimised for fillet work and detail milling where tool overhang must be minimised. The short overall length helps to suppress vibration and chatter, which translates into improved surface finish and dimensional accuracy on medium-strength steels and cast iron. Durable cutting performance and material suitability Made from HSS‑Co8 and finished with TiCN coating, the cutter combines the toughness of cobalt-alloy high-speed steel with a hard, low-friction surface layer to extend tool life under intermittent cutting conditions. The centre-cutting geometry permits secure plunge milling, while the two-flute layout balances chip evacuation and cutting engagement. The tool is specified for machinability in steels up to approx. 1200 N/mm² and is also very well suited to cast iron; non-ferrous and high-alloy materials are conditionally suitable depending on cutting data and coolant application. Secure clamping and practical dimensions for workshop use A Weldon shank with drive flat gives reliable torque transmission in collets and chucks, reducing slippage in demanding operations. The tool features an effective length of 13 mm, cutting length 2 mm, and a shank diameter of 6 mm, with an overall length of 51 mm, making it easy to integrate into small tooling set-ups and multi-spindle fixtures. The right-hand cutting orientation and two cutting edges support efficient material removal while maintaining straightforward toolpath planning. Maintenance is straightforward: inspect the coating and cutting edges and replace the cutter when wear compromises accuracy. For reliable, high-rigidity radius milling choose the TECWERK full-radius end mill; contact Metav Werkzeuge for tailored advice or ordering assistance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000866598NW Product: Full-radius end mill Brand: TECWERK Material: HSS‑Co (HSS‑Co8) Coating: TiCN Shank type: Weldon (drive flat) Cutting edges: 2 Cutting direction: right‑hand Facts Diameter: 4 mm Radius: 2 mm Overall length: 51 mm Effective length: 13 mm Cutting length: 2 mm Shank diameter: 6 mm Special features Extra‑short design Centre‑cutting (plunge capable) Cylindrical shank with drive flat Suited for steel up to approx. 1200 N/mm² Very well suited for cast iron Conditionally suitable for non‑ferrous metals, special alloys and inox FAQ What materials is the TECWERK full-radius end mill best used for? The TECWERK full-radius end mill is very well suited for machining steel and cast iron, and it is conditionally suitable for non‑ferrous metals, special alloys and inox depending on cutting data. Can the cutter be used for plunge milling? Yes. The centre-cutting geometry allows the cutter to plunge into the workpiece for short-reach operations and pocket starts. What are the key dimensions to check for fixture compatibility? Important dimensions are the 4 mm diameter, 6 mm shank and 51 mm overall length; the effective length is 13 mm and the cutting length is 2 mm. How does the TiCN coating affect service life? The TiCN coating reduces friction and increases wear resistance compared with uncoated HSS, improving tool life under suitable cutting conditions. Is the Weldon shank suitable for standard toolholders? The Weldon shank with drive flat provides secure clamping in holders that accept a 6 mm shank with a Weldon-style flat. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from solid carbide construction and a TiAlN surface for extended tool life, precise fillet profiles and stable performance in mixed-material production. Order the cutter directly via Metav Werkzeuge or consult our specialists for machining guidance. Full-radius end mill D.5 mm, TiAlN, TECWERK — short, centre-cutting carbide tool The Full-radius end mill D.5 mm, TiAlN, TECWERK is a compact, centre-cutting fillet cutter designed for precise radius milling and small-feature machining across steels and non-ferrous materials Solid carbide, TiAlN coating Centre-cutting for plunge milling 30° helix for smooth chip evacuation Cylindrical shank DIN 6535 HB Precise fillet formation with minimal rework The full-radius geometry delivers a consistent edge transition and reduces the need for secondary finishing. The tool’s 5 mm diameter with a 2.5 mm radius generates accurate fillet profiles in a single pass, while the 2 flutes ensure a clean contact zone and low cutting forces. As a centre-cutting design, the cutter allows controlled plunging into the workpiece for pockets or intersecting contours, translating into shorter set-up times and fewer tool changes on batch runs. Longer tool life under heat and load A TiAlN surface treatment combined with solid carbide construction raises thermal resistance and surface hardness, delaying wear during sustained dry or MQL operations. This coating supports reliable performance when machining steel, stainless steels and cast iron, as well as non-ferrous metals and special alloys listed for the tool. The result is predictable tool life, fewer interruptions for tool change and improved process economy for repetitive production. Stable clamping and vibration suppression for tight tolerances The short design and DIN 6535 HB cylindrical shank increase rigidity at the spindle, reducing deflection when working close to shoulders or in tight pockets. With a 6 mm shank, effective length 16 mm and overall length 54 mm, the cutter offers concentrated stability for small-feature milling. The 30° helix angle and right-hand cutting geometry favour smooth chip flow and lower chatter, supporting dimensional consistency and surface quality in demanding setups. Versatile application advice for mixed-material workshops This radius cutter suits operations that require a single, reliable tool for fillet radii, edge breaks and small-profile finishing across multiple materials. As the tool is specified for centre cutting and a variety of substrates, it is particularly effective where a compact tool must handle steel, castings, copper alloys and abrasive plastics without frequent tool swapping. For optimal feed and speed settings tailored to the machine and material, consult Metav Werkzeuge’s machining advisors to adapt parameters to individual production needs. Contact Metav Werkzeuge for tailored machining parameters, stock availability and ordering: eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000866972NW Label: Vollradiusfräser D.5mm Einsatz-L.16mm VHM TiAlN HB Z.2 kurz TECWERK Manufacturer: TECWERK Product type: Vollradiusfräser Core data Diameter: 5 mm Radius: 2.5 mm Overall length: 54 mm Effective length: 16 mm Cutting length: 2 mm Shank diameter: 6 mm Flutes: 2 Relief length: 4.8 mm Special features Solid carbide, fine-grain TiAlN coating Centre cutting DIN 6535 HB cylindrical shank 30° helix angle Right-hand cutting Suitable for steel; stainless (INOX); cast iron; non-ferrous metals; special alloys; aluminium with silicon; abrasive plastics Shank tolerance h6 Short version; 2-flute design FAQ Which materials is this full-radius end mill suitable for? This full-radius end mill is specified for a broad range of materials; the tool is very well suited for steel, stainless steels (INOX), cast iron, non-ferrous metals and certain special alloys as indicated in the product data. Can the cutter perform plunge cuts and pocketing? Yes. The centre-cutting geometry enables plunge cutting and pocketing operations, making the cutter suitable for intersecting contours and fillet features. What clamping does the tool require? The tool features a DIN 6535 HB cylindrical shank with a 6 mm diameter and h6 tolerance; standard collets or tool holders matching that shank specification are appropriate. How does the TiAlN coating benefit machining? The TiAlN coating increases surface hardness and heat resistance, improving wear behaviour under elevated temperatures and supporting longer tool life during continuous machining cycles. What is the SKU for ordering and which tool type should be requested? Order using SKU 2000866972NW and request the TECWERK full-radius end mill (solid carbide, TiAlN, 5 mm diameter, short version). Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the HSS‑Co8 base material together with a TiCN coating for extended wear resistance and stable surface finish in short‑reach milling tasks; the compact Weldon shank and extra‑short geometry reduce overhang for improved rigidity. Order the cutter through Metav Werkzeuge or consult the technical team for application advice. TECWERK corner‑radius end mill — 6 mm, HSS‑Co8, TiCN, Weldon, 2 flutes The TECWERK corner‑radius end mill is designed for short‑reach milling of steels and castings, combining a robust cobalt‑alloy high‑speed steel body with a TiCN coating for longevity in production environments. HSS‑Co8 base material for high toughness TiCN coating for extended tool life Extra‑short Weldon shank for rigid setup Centre‑cutting, right‑hand spiral flutes Stable tool life and consistent results in steel machining The cutter is built from HSS‑Co8, a cobalt‑enriched high‑speed steel chosen for its toughness and heat resistance; combined with the TiCN surface layer, this provides higher wear resistance and longer tool life compared with uncoated alternatives. For components in the workshop that demand repeatable finish and dimensional stability, the coating reduces built‑up edge and improves surface quality, while the substrate steel tolerates intermittent overload and elevated cutting temperatures. This makes the tool particularly suitable for machining steels up to 1200 N/mm², offering a reliable balance between abrasion resistance and edge stability. Short overhang and centre‑cutting geometry for chatter reduction The extra‑short overall length and Weldon shank minimise unsupported overhang, improving rigidity during high‑precision milling. With just 2 flutes and a centre‑cutting geometry, the tool enables axial plunging and efficient chip evacuation in short depths of cut; the 14 mm effective cutting length is optimised for pocketing and slotting where access is limited. The compact design reduces vibration, so cycle times can be maintained without sacrificing surface finish — a pragmatic solution where machine rigidity and fixture stability are decisive for process reliability. Versatile application across castings, steel and mixed alloys With a 3 mm corner radius the cutter produces rounded internal corners that reduce stress concentration and increase component life in service. The tool performs very well on steel and cast materials, with conditional suitability for non‑ferrous metals, stainless steels and special alloys; machining strategy and cutting data should be selected accordingly. Right‑hand cutting and the cylindrical shank with drive flat (Weldon) ensure secure clamping in standard toolholders, supporting consistent concentricity and dimensional repeatability across batches. For workshops seeking a durable short‑reach cutter that balances surface finish, rigidity and tool life, this radius cutter represents a practical investment. For reliable short‑reach milling with improved wear resistance choose the TECWERK corner‑radius end mill and procure directly via Metav Werkzeuge for dependable supply from Emmerich — contact Metav’s technical advisors at info@metav-werkzeuge.com or +49 2822 7131930 for tailored cutting data and delivery options. Technical data Article number: 2000866602NW Label: Vollradiusfräser D.6mm Einsatz‑L.14mm HSS‑Co8 TiCN Weldon Z.2 ext.kurz Manufacturer: TECWERK Product type: Corner‑radius end mill Numbers / Core technical data Diameter: 6 mm Radius: 3 mm Overall length: 52 mm Effective cutting length: 14 mm Cutting length: 2 mm Shank diameter: 6 mm Flutes: 2 Relief / clearance: 5.5 mm Suitable strength range: up to approx. 1200 N/mm² Designs / Special features HSS‑Co8 substrate TiCN coating Weldon shank / cylindrical shank with drive flat Centre‑cutting (axial plunge capability) Extra‑short design for reduced overhang Right‑hand cutting direction Factory standard specification Very good suitability: steel, castings Conditional suitability: non‑ferrous metals, stainless, special alloys FAQ Which materials are best machined with this corner‑radius end mill? The TECWERK corner‑radius end mill is optimised for steel and castings (very good suitability) and can be used conditionally on non‑ferrous metals, stainless steel and certain special alloys with adapted cutting data. Does the TiCN coating significantly extend tool life? Yes — the TiCN coating on this radius cutter reduces abrasive wear and built‑up edge, which prolongs life compared with uncoated HSS‑Co tools under comparable cutting conditions. Can the tool perform plunge cuts due to its geometry? The centre‑cutting configuration allows axial plunging; the 2‑flute design and 14 mm effective length support short‑reach plunge and pocketing operations with good chip evacuation. What clamping is required for best performance? Secure clamping of the Weldon shank (cylindrical shank with drive flat) in a rigid toolholder is recommended to exploit the extra‑short geometry and maintain concentricity and repeatability. What component feature does the 3 mm radius provide? A 3 mm corner radius reduces stress concentration in internal corners and improves fatigue resistance, while also aiding a more durable cutting edge when performing fillet milling. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a short, rigid geometry and a TiAlN-coated solid-carbide cutting head to achieve dependable surface finishes and extended tool life; the centre-cut, 2‑flute design improves chip evacuation and stability in tight features. Order the tool directly via Metav Werkzeuge or consult our specialists for process matching and delivery from Emmerich. Full-radius end mill Ø6 mm — solid carbide, TiAlN, short version (TECWERK) The Full-radius end mill Ø6 mm, solid carbide, TiAlN is a short, centre‑cutting cutter engineered for precise finishing and robust milling across steels, cast irons and non‑ferrous alloys. Solid carbide full-radius geometry TiAlN coating for extended tool life Short design with centre-cut capability DIN 6535 HB shank, tolerance h6 Faster, more consistent finishing in mixed production The short full‑radius geometry combined with a solid carbide substrate and TiAlN surface treatment delivers high wear resistance and thermal stability, allowing higher cutting speeds and longer tool life. With a compact 6 mm diameter and 2 flutes, the cutter is optimised for reduced vibration and improved chip evacuation; the 30° helix further supports smooth chip flow. These characteristics translate into measurable process gains: fewer tool changes, steadier surface quality and predictable cycle times, which directly contribute to production efficiency and lower unit costs. Secure clamping and reliable reach for precision features Designed with a DIN 6535 HB cylindrical shank and h6 tolerance, the tool offers repeatable clamping accuracy and minimised runout in standard toolholders. The tool’s cutting length 2 mm and effective length 16 mm create a balance between local cutting capability and sufficient reach for small cavities or stepped features, while the centre‑cutting geometry permits axial plunging where required. Compatibility with a broad range of materials — including steel, stainless (CrNi) steels, cast iron, bronze, brass, copper, aluminium with silicon content and abrasive plastics — ensures versatility across order types and job batches without frequent tool swaps. Shop-floor robustness and straightforward integration The short version and two‑cutting‑edge design provide increased rigidity, which reduces deflection during finishing passes and improves dimensional stability in a repetitive production setting. The factory specification (Type N) and the clearances indicated by the relief value support consistent performance in both manual and CNC milling operations. For workshops seeking dependable tooling that is simple to integrate into existing setups, this tool offers a pragmatic combination of stiffness, repeatability and low maintenance overhead — qualities that help maintain throughput while keeping process variables under control. Contact Metav Werkzeuge to discuss how the TECWERK full‑radius end mill with TiAlN coating can be integrated into current milling cycles — technical advice and supply are available directly from Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866973NW Label: Vollradiusfräser D.6mm Einsatz-L.16mm VHM TiAlN HB Z.2 kurz TECWERK Manufacturer: TECWERK Numbers / Core technical data Diameter: 6 mm Overall length: 54 mm Effective length: 16 mm Cutting length: 2 mm Flutes: 2 Shank diameter: 6 mm Radius: 3 mm Relief mm: 5.8 Helix angle: 30° Special features Material: solid carbide (fine grain) Coating: TiAlN Centre‑cutting (Zentrumschnitt) Right‑hand cutting Short version Cylindrical shank to DIN 6535 HB Shank tolerance: h6 Factory standard Type N Very well suited for steel, cast iron, stainless steel, non‑ferrous metals and abrasive plastics FAQ Which materials is the cutter suitable for? The TECWERK full‑radius end mill (SKU 2000866973NW) is very well suited for steel, cast iron, stainless (CrNi) steels, bronze, brass, copper, aluminium with silicon and abrasive plastics. Can the tool be used for plunge milling? Yes — the centre‑cutting geometry allows axial plunging and makes the cutter suitable for short‑depth plunge operations as well as finishing passes. What shank and tolerance are required for accurate clamping? The tool features a cylindrical shank to DIN 6535 HB with h6 tolerance; use holders compatible with this standard to ensure repeatable concentricity. How does the TiAlN coating benefit workshop processes? The TiAlN coating increases thermal resistance and wear protection, extending tool life under elevated cutting temperatures and improving stability during hard or abrasive operations. What are the key dimensions to consider when programming operations? Key dimensions: diameter 6 mm, cutting length 2 mm, effective length 16 mm, overall length 54 mm; these determine plunge depth, step‑over limits and fixture clearance. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

The combination of a HSS‑Co8 substrate and TiCN coating delivers durable performance for short-reach profiling and plunge operations; this reduces tool changes and supports stable production. Benefit from the extra-short design and centre-cutting geometry for rigid setups and precise edge radii. Order the full-radius cutter directly via Metav Werkzeuge or ask the consultants for tailored advice. Full-radius end mill Ø 8 mm — HSS‑Co8, TiCN, extra-short (TECWERK) A full-radius end mill Ø 8 mm engineered for short-reach profiling, centre plunging and high-precision finishing in steel and cast-iron applications HSS‑Co8 substrate with TiCN coating Extra-short design for rigid, chatter-free milling Centre-cutting two-flute geometry Cylindrical shank with Weldon drive flat Precise short-reach profiling with consistent radii The HSS‑Co8 substrate supplies high red hardness and toughness for interrupted cuts, while the TiCN surface reduces adhesion and abrasive wear. Together these properties make the tool suitable for demanding finishing and profiling tasks where a defined corner radius is required. With a radius 4 mm on a Ø 8 mm body and a cutting geometry that permits axial plunging, the cutter achieves repeatable contours and clean transitions without secondary operations. The design supports fewer tool changes, improving cycle reliability in serial production. Machining performance and material suitability explained This cutter is optimised for ferrous materials: steel and cast iron are indicated as very well suited, while non-ferrous and special alloys are conditionally machinable. The tool’s right-hand cutting direction and centre-cutting capability mean it can enter material axially for pocketing or interrupted features. The short cutting length and stiff geometry reduce deflection and vibration, which leads to improved surface finish and tighter tolerances on critical components. For workshops requiring repeatable edge radii, the tool provides an efficient, low-setup solution. Coating and geometry: why longevity and surface quality improve The TiCN coating lowers friction and raises thermal stability compared with uncoated HSS, which supports higher cutting speeds and extended tool life under comparable conditions. The two-flute design evacuates chips efficiently in shallow cuts, and the extra-short overall profile reduces overhang to limit chatter. Centre-cutting flutes enable plunge cuts without pre-drilling, saving cycle steps in many operations. These design choices translate directly into less downtime, more consistent part quality and a measurable reduction in rework. Mounting, handling and integration into the workflow The tool features a cylindrical shank with Weldon drive flat and a shaft diameter 10 mm, enabling secure clamping in standard holders and torque transmission for higher loads. The tool’s effective length 17 mm and overall length 61 mm are balanced for compact setups on milling heads or small machines. Due to the extra-short format and stiff shank, it is especially suitable for jigs, fixtured parts and milling operations with limited clearance. Clear labelling and industry-standard shank geometry make integration straightforward for production and tool management systems. For precision short-reach profiling with TECWERK’s full-radius cutter, contact Metav Werkzeuge in Emmerich for availability and application advice: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 2000866604NW SKU: 2000866604NW Brand: TECWERK Product type: Full-radius end mill Facts Diameter: 8 mm Radius: 4 mm Overall length: 61 mm Effective length: 17 mm Cutting length: 2 mm Shank diameter: 10 mm Relief (freischliff): 7.5 mm Number of flutes: 2 Special features Material: HSS‑Co8 Coating: TiCN Centre-cutting geometry Extra-short design Right-hand cutting Weldon drive flat on cylindrical shank Very well suited for steel Very well suited for cast iron Conditionally suitable for non-ferrous metals and special alloys FAQ What materials is this full-radius cutter best suited for? The full-radius end mill (TECWERK, SKU 2000866604NW) is stated as very well suited for steel and cast iron, with conditional suitability for non-ferrous metals and special alloys. Can the tool perform plunge cuts or pocketing operations? Yes. The centre-cutting two-flute geometry allows axial plunging, so the cutter can be used for pocketing and plunge operations without prior drilling. How does the TiCN coating benefit tool life? The TiCN coating reduces friction and improves wear resistance compared with uncoated HSS, which helps to extend service intervals and maintain surface finish consistency. Is the shank compatible with standard tool holders? The cylindrical shank with Weldon drive flat and 10 mm shaft diameter is compatible with standard collet chucks and Weldon-style holders for secure clamping. What are the dimensions relevant for fixture planning? Key dimensions: Ø 8 mm, effective length 17 mm, overall length 61 mm and a cutting length of 2 mm; these define reach and clamping requirements. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from the combination of a TiAlN coating, solid carbide construction and a short design for stable, high-precision contour milling; order directly via Metav Werkzeuge or contact the consultants for application advice. TECWERK Full-radius end mill D 8 mm (solid carbide, TiAlN, 2 flutes) A TECWERK Full-radius end mill engineered for short, high-precision finishing and contour work across steels, castings and non-ferrous alloys. Short solid carbide design with TiAlN coating Radius tip for contour finishing Suitable for steel, cast iron and non-ferrous metals DIN 6535 HB shank, tolerance h6 Exceptional performance through coating and substrate The combination of a TiAlN surface layer and solid carbide fine-grain substrate delivers a clear performance advantage: improved heat resistance and reduced wear under increased cutting temperatures. For short, demanding passes the tool’s 8 mm diameter and compact geometry enable higher stability and lower vibration, which contributes to longer tool life and consistent surface quality. These material and coating choices benefit high-volume workshops and precision jobbing alike by reducing unplanned tool changes and improving process predictability. Accurate contouring and plunge capability for profile work A full-radius tip with centre-cut capability permits precise contour finishing and controlled plunge operations without compromising edge integrity. The tool’s 2 flutes and 30° helix favour reliable chip evacuation in many alloys, while the 20 mm effective length keeps the cutting zone rigid for repeatable tolerances. The short flute length and radius geometry are particularly suitable when a fine profile and smooth transition radii are required, making the cutter ideal for dies, mould components and detail work on components with complex edges. Secure clamping and machine compatibility for steady results The DIN 6535 HB shank with h6 tolerance ensures concentric clamping and reduced runout when used with standard collets and tool holders. This mechanical precision translates into improved surface finishes and reduces the need for finishing passes. The overall length of 58 mm and an 8 mm shank diameter match many compact machining setups, allowing efficient integration into small mills and CNC centres while maintaining secure retention for interrupted or heavy cuts. Broad material suitability and workshop efficiency Designed as a universal fine-grain solid carbide cutter, the tool is rated very well suited for a wide range of materials: steels, stainless grades, cast iron (including grey and tempered), special alloys, bronzes, brass, copper, aluminium with silicon content and abrasive plastics. The short design and TiAlN coating also help to mitigate built-up edge in sticky or gummy materials, resulting in more consistent chip formation and reduced downtime. For production workshops this means fewer tool changes, improved cycle consistency and predictable component quality. Contact Metav Werkzeuge for availability, batch sizes and application guidance—technical consultants are available to advise on cutting data and holder selection and can be reached via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866974NW Manufacturer: TECWERK Product type: Full-radius end mill Label: Vollradiusfräser D.8mm Einsatz-L.20mm VHM TiAlN HB Z.2 kurz TECWERK Facts Diameter: 8 mm Overall length: 58 mm Effective length: 20 mm Cutting length: 2 mm Number of flutes: 2 Radius: 4 mm Shank diameter: 8 mm Free relief: 7.7 mm Helix angle: 30° Materials & special features Coating: TiAlN Material: Solid carbide (fine-grain) Cutting direction: Right-hand cutting Centre-cut for plunge milling Short design for high rigidity Shank standard: DIN 6535 HB Shank tolerance: h6 Suitable for: Steel, cast iron, grey & tempered cast iron, CrNi steels, bronze, brass, copper, aluminium with silicon content, abrasive plastics, special alloys, INOX Werknorm / factory standard: Typ N · Zweischneider · Werksnorm FAQ Which materials can this cutter machine effectively? The TECWERK Full-radius end mill is very well suited for machining steel, cast iron (including grey and tempered), CrNi steels, bronze, brass, copper, aluminium with silicon content, abrasive plastics and many special alloys. Is the tool suitable for plunge or slotting operations? Yes, the cutter features centre-cut capability, allowing controlled plunge milling and slotting in short engagement depths with the full-radius geometry. What ensures accurate clamping and low runout? The tool has a DIN 6535 HB shank with h6 tolerance; this standardised shank and tolerance support concentric clamping and reduced runout when used with compatible collets and holders. How does the TiAlN coating benefit performance? The TiAlN coating increases surface hardness and thermal resistance, reducing wear at elevated cutting temperatures and improving tool life and edge integrity during demanding passes. What are the key geometric data for integration into a tool plan? Key dimensions: 8 mm diameter, 20 mm effective length, 2 mm cutting length, 58 mm overall length, 30° helix, 2 flutes and a 4 mm radius tip. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund