10mm Full Radius Cutter 21mm Effective Length TiCN Coated HSS-Co8 2-Flute Weldon Shank - TECWERK

Combine the TiCN coating with HSS‑Co8 construction and the R5 full‑radius profile for robust finishing and long tool life; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice.

TECWERK full‑radius end mill D10 mm — HSS‑Co8, TiCN, Weldon

The TECWERK full‑radius end mill D10 mm is an extra‑short, centre‑cutting radius cutter for precise machining of steel and cast components in compact, rigid set‑ups.

• Extra‑short 2‑flute geometry for rigid set‑ups
• TiCN coating for increased wear resistance
• HSS‑Co8 material for high toughness and heat resistance
• Weldon shank with drive flat for secure clamping

High‑performance finishing for steel and cast parts

Manufactured for demanding finishing operations, this radius cutter combines a R5 full‑radius profile with HSS‑Co8 base material to deliver consistent corner geometry and improved edge strength. The 10 mm diameter and 21 mm effective length are optimised for short‑span milling where rigidity and repeatable results matter. For components up to approximately 1200 N/mm² tensile strength, the tool offers reliable material removal with reduced risk of chipping, making it particularly suited to fine machining of steel and cast iron components.

Coating and substrate: why TiCN on HSS‑Co8 works

The combination of a TiCN coating on an HSS‑Co8 substrate increases surface hardness and thermal resistance without sacrificing the substrate’s inherent toughness. This means longer tool life under intermittent cutting and better resistance to built‑up edge. The two‑flute geometry supports efficient chip evacuation and stable cutting forces, while the centre‑cutting design allows plunge and profile milling. For users with limited tool change windows, the coating‑substrate pairing reduces downtime and contributes to a more economical production rhythm.

Rigidity, clamping and handling in compact setups

Designed as an extra‑short tool with a Weldon shank and drive flat, this cutter prioritises secure clamping and minimal overhang. That rigidity translates directly into improved surface finish and dimensional consistency when working in tight fixtures or small milling heads. The reduced effective projection lowers vibration susceptibility, so set‑ups that demand repeatable radiused contours benefit from fewer rejects and faster set‑up verification. The relief grind of 9.5 mm supports clearance during radial engagement and simplifies fixture alignment.

Practical applications and machining advice

This full‑radius end mill excels in finishing radiused pockets, fillets and die features where a precise corner radius is required. The two‑flute layout is advantageous for steels and cast materials, while non‑ferrous and special alloys are machinable with moderated parameters. Being right‑hand cutting and centre‑cutting, the cutter permits plunge starts and conventional profiling. When calculating feeds and speeds, prioritise rigidity and coolant strategy to exploit the TiCN wear resistance; shorter axial depths and stable RPMs prolong tool life and enhance surface integrity.

For supply of TECWERK full‑radius end mills and tailored application recommendations based on TiCN‑coated HSS‑Co8 geometry, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for direct procurement and expert consultancy.

Technical Data

• Article number: 2000866606NW
• Manufacturer: TECWERK

Facts

• Diameter: 10 mm
• Overall length: 63 mm
• Effective length: 21 mm
• Cutting length: 2 mm
• Shank diameter: 10 mm
• Radius: 5 mm
• Number of flutes: 2
• Relief grind: 9,5 mm

Special features

• Material: HSS‑Co8
• Coating: TiCN
• Centre‑cutting
• Weldon shank with drive flat
• Extra short design
• Right‑hand cutting
• Very good suitability for steel
• Very good suitability for cast iron
• Conditional suitability for non‑ferrous metals, special alloys and inox

FAQ

What materials is this cutter best suited for?
The cutter is very well suited for steel and cast iron applications; non‑ferrous metals, special alloys and stainless steels are machinable with adjusted parameters for the TiCN‑coated HSS‑Co8 tool.

Can the tool be used for plunge milling?
Yes. The centre‑cutting geometry allows plunge starts and makes the cutter suitable for profile and pocketing tasks where a radiused corner is required.

How does the TiCN coating affect performance?
The TiCN coating increases surface hardness and thermal resistance, improving wear life and reducing built‑up edge compared with uncoated HSS tools.

What size and shank specifications does the tool have?
The cutter has a 10 mm diameter, 10 mm shank and a Weldon shank with drive flat to ensure secure clamping in rigid fixtures.

Which SKU identifies this tool for ordering?
Refer to SKU 2000866606NW when ordering the TECWERK full‑radius end mill to ensure the correct specification is supplied.

TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund