16mm Full Radius Cutter 29mm Effective Length TiCN Coated HSS-Co8 Extra Short Right-Hand - TECWERK

Benefit from the combination of HSS‑Co8 toughness, TiCN surface protection and a secure Weldon shank for reliable, vibration‑resistant milling; order the full‑radius end mill (TECWERK 2000866612NW) directly via Metav Werkzeuge or ask our consultants if needed.

TECWERK full‑radius end mill D16 mm — HSS‑Co8, TiCN, Weldon

The TECWERK full‑radius end mill D16 mm is an extra‑short, centre‑cutting milling tool designed for rigid machining of steel and cast workpieces in demanding production environments

• HSS‑Co8 base material for heat resistance
• TiCN coating for increased wear resistance
• Weldon shank for positive drive
• Extra‑short design for maximum rigidity

Faster, more consistent metal removal with cobalt‑alloy steel

The tool combines HSS‑Co8 substrate hardness with a TiCN coating to reduce friction and extend tool life during continuous milling. The 2‑flute geometry supports efficient chip evacuation while the centre‑cutting geometry allows controlled plunging operations. As a result, milling cycles become more predictable and process capability is improved, particularly where repeated contouring and pocketing of ferrous components is required.

Secure clamping and improved runout control for repeatable accuracy

A Weldon shank with drive flat and a 16 mm shank diameter provide a positive, slip‑free interface in most toolholders, supporting stable torque transmission and minimising runout. The tool’s effective length of 29 mm together with an extra‑short overall length reduces overhang and increases stiffness, delivering better surface finish and dimensional consistency on series parts where tight tolerances matter.

Clear guidance on suitable applications and materials

Designed primarily for machining steel and cast components, the cutter is rated for workpiece strengths up to approx. 1200 N/mm². Performance in non‑ferrous metals, special alloys and stainless steel is conditional; the combination of substrate and coating is optimised for steels and castings, where heat resistance and wear control are decisive. The geometry and coating support roughing and semi‑finishing tasks where both material removal and tool life are priorities.

Practical handling to extend service life and maintain productivity

To get the most from the tool, ensure firm clamping and minimise overhang to exploit the inherent rigidity of the short design. The TiCN layer helps against abrasive wear and built‑up edge, while the cobalt alloy maintains hardness at elevated temperatures; appropriate use of coolant and stable fixturing will further extend tool life. Regular inspection of clamping surfaces and the Weldon flat keeps runout low and repeatability high in production runs.

Contact Metav Werkzeuge today to discuss the TECWERK full‑radius end mill (SKU 2000866612NW) and secure the right solution for the workshop — email info@metav-werkzeuge.com or call +49 2822 7131930

Technical Data

• Article number: 2000866612NW
• Product: Full‑radius end mill D16 mm (TECWERK)
• Manufacturer: TECWERK

Facts

• Diameter: 16 mm
• Corner radius: 8 mm
• Effective length: 29 mm
• Overall length: 79 mm
• Shank diameter: 16 mm
• Cutting edges: 2
• Relief (freischliff): 15 mm

Special features

• Material: HSS‑Co (HSS‑Co8)
• Coating: TiCN
• Weldon shank (cylindrical shank with drive flat)
• Centre cutting
• Right‑hand cutting
• Extra‑short design
• Suitable for steels up to approx. 1200 N/mm²
• Very good for steel and cast; conditionally suitable for non‑ferrous metals, special alloys and stainless steel

FAQ

What materials can be machined reliably with this cutter? The TECWERK full‑radius end mill is very well suited to steel and cast components and is specified for workpiece strengths up to approximately 1200 N/mm²; performance in non‑ferrous metals, special alloys and stainless steel is conditional.

Is this tool suitable for plunge cutting? Yes. The tool’s centre‑cutting geometry permits controlled plunging, enabling shorter setups for pocketing or when axial entry is required.

How does the TiCN coating benefit production use? The TiCN coating lowers friction and improves wear resistance compared with uncoated high‑speed steel, which helps maintain cutting edge integrity and reduces downtime for tool changes in longer production runs.

Which shank type is used and why does it matter? A Weldon shank with drive flat is provided to ensure a positive, slip‑free connection in the toolholder; this improves torque transmission and reduces runout for better repeatability.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund