6mm Solid Carbide Deburring Cutter TiAlN Coated 45° 4-Flute Extra Long 100mm Shank - TECWERK

Take advantage of the combination of an advanced TiAlN coating, a precise 45° cutting geometry and an extra‑long design for consistent chamfering and fast tool changes; order the tool directly via Metav Werkzeuge or consult our specialists for application advice.

Forward/Reverse Deburring Cutter D 6 mm, TiAlN, 45° — TECWERK

The Forward/Reverse Deburring Cutter D 6 mm is an extra‑long, four‑flute tool engineered for precise chamfering and deburring in machining operations

• TiAlN coating for extended tool life
• 45° cutting angle for accurate chamfers
• Extra‑long 100 mm overall length
• Four flutes for smooth edge finishing

Durable coating for higher thermal resistance and longer service life

The combination of a TiAlN surface treatment and a robust flute geometry reduces abrasive wear and increases resistance to heat during interrupted cuts. This results in longer intervals between tool changes and more predictable tool life, which supports continuous production. The coated surface improves performance on repeated edge preparation tasks, contributing to lower tooling costs per part and fewer stoppages for regrinding or replacement.

Geometry that delivers consistent chamfers and low burr formation

A defined 45° cutting angle paired with four flutes produces a controlled material removal and a neat chamfered edge with reduced burr height. The tool’s right‑hand cutting direction and the 4 mm cutting length enable precise control when deburring or creating a chamfer of limited depth, while the Ø 6 mm shank ensures compatibility with standard collet systems. The result is a reliable surface finish that shortens downstream finishing work.

Extended reach and practical handling for workshop use

The extra‑long overall length of 100 mm and a cylindrical shank Ø 6 mm provide access to recessed features and workpieces with restricted fixturing, without compromising rigidity in typical setups. The tool’s construction as a four‑flute deburring cutter helps maintain chip evacuation and reduces vibration during light chamfering passes. Where space is constrained or access angles vary, this configuration offers a practical balance of reach and stability.

For expert guidance on integrating the TECWERK deburring cutter into production workflows or to arrange supply from Metav Werkzeuge’s Emmerich warehouse, contact our team at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s specialists will advise on tooling selection and delivery options.

Technical Data

• Article number: 2000866613NW
• SKU / Label: Vor-/Rückwärtsentgrater D.6mm VHM TiAlN 45Grad Z.4 ext.lang TECWERK
• Manufacturer: TECWERK

Numbers / Core Technical Data

• Diameter: 6 mm
• Overall length: 100 mm
• Cutting length: 4 mm
• Shank diameter: 6 mm
• Number of flutes: 4
• Free grind / clearance: 15 mm

Special features / Versions

• TiAlN coating
• 45° cutting angle
• Extra‑long design
• Cylindrical shank
• Right‑hand cutting direction
• For forward and reverse deburring and chamfering

FAQ

What materials is this deburring cutter suited for?
The TECWERK deburring cutter is designed for general chamfering and deburring operations; its TiAlN coating enhances wear resistance for demanding use but material‑specific suitability should be confirmed with Metav Werkzeuge for specialised alloys.

What does the extra‑long design mean in practice?
An overall length of 100 mm gives extended reach to access recessed edges and workpieces with deeper fixtures while retaining sufficient rigidity for controlled chamfering.

How deep can the cutter chamfer in a single pass?
The tool’s specified cutting length of 4 mm defines the maximum effective chamfering depth per pass; for larger chamfers, multiple passes or a different tool geometry should be considered.

Is the shank compatible with standard collets?
Yes, the Ø 6 mm cylindrical shank is compatible with common collet chucks and holders used in general workshop and CNC setups.

How many flutes does the cutter have and why does that matter?
The cutter has four flutes, which balance material removal with surface finish and chip control, making it suitable for producing clean chamfers with reduced burr formation.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund