Vor-/Rückwärtsentgrater D.12mm VHM TiAlN 45Grad Z.4 ext.lang TECWERK Vor-/Rückwärtsentgrater D.12mm VHM TiAlN 45Grad Z.4 ext.lang TECWERK eignet sich für präzise Entgratungs- und Anfaserarbeiten in der Serienfertigung auf Dreh- und Fräsmaschinen Vierschneider für saubere Kanten TiAlN-Beschichtung für höhere Standzeit Extra langes Ausführungsmaß für tiefe Taschenschnitte Schaft-Ø 6 mm für kompakte Spannsituationen 45° Winkel für gleichmäßige Anfasungen lange Standzeit durch robuste Beschichtung Die Kombination aus Vollhartmetall und TiAlN-Beschichtung sorgt für deutlich verbesserte Verschleißfestigkeit bei warmen Schnittbedingungen. Die TiAlN-Beschichtung reduziert Aufbauschneiden und erhöht die Standzeit, was Werkzeugwechsel in der Fertigung minimiert. Durch die robuste Beschichtung bleibt die Schneidkante länger scharf, sodass weniger Nachbearbeitung anfällt und die Produktivität gesteigert wird. vielseitiger Einsatz in Produktion und Werkstatt Für Anwender in Industrie, Handwerk und Lohnfertigung bietet das Werkzeug klare Vorteile: Es eignet sich zum Vor- und Rückwärtsentgraten sowie zum Anfasen von Bauteilkanten. Besonders in der Serienbearbeitung zeigt sich der Nutzen, weil saubere Kanten und reproduzierbare Anfasungen die Montagequalität erhöhen. Die Bauform als Vierschneider liefert gleichmäßige Schnitte und reduziert Gratbildung bei unterschiedlichen Werkstoffen. stabile Ausführung für reproduzierbare Ergebnisse Das extra lange Design ermöglicht das Erreichen tieferer Bereiche ohne Verlust an Stabilität. Mit Durchmesser 12 mm und Schaft-Ø 6 mm bleibt die Werkzeugaufnahme kompakt, was sich bei beengten Spannsituationen auszahlt. Die 45° Geometrie sorgt für saubere Anfasungen, die sich leicht nachfolgend messen und verifizieren lassen. Insgesamt reduziert sich der Ausschuss, da Bauteile mit konsistenter Kantenqualität produziert werden. Empfehlung: Das TECWERK Vor-/Rückwärtsentgrater mit TiAlN-Beschichtung ist besonders für Serienfertigung geeignet; Anfrage und Bestellung über Metav Werkzeuge GmbH, eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produkteigenschaften Artikelnummer: 2000866618NW Marke: TECWERK Bezeichnung: Vor-/Rückwärtsentgrater D.12mm VHM TiAlN 45Grad Z.4 ext.lang Verpackungseinheit: 1 Schaft-Ø: 6 mm Fakten Durchmesser: 12 mm Schaft-Ø: 6 mm Zähne: 4 Winkel: 45° Besonderheiten Material: Vollhartmetall (VHM) Beschichtung: TiAlN (Titan-Aluminium-Nitrid, hohe Wärmeresistenz) Bauform: Vierschneider Ausführung: extra lang, Zylinderschaft Einsatz: Vor- und Rückwärtsentgraten Anwendung: Anfasen Werksnorm FAQ Wie hoch ist die Schneidkantenzahl und welche Vorteile bietet sie? Die Schneidkantenzahl beträgt 4 Zähne; der Verschleiß verteilt sich auf mehrere Schneiden, wodurch die Standzeit des Vor-/Rückwärtsentgraters von TECWERK steigt und die Oberflächenqualität der Anfasung verbessert wird. Ist das Werkzeug für die Serienfertigung geeignet? Ja, das Vor-/Rückwärtsentgrater D.12mm VHM TiAlN 45Grad Z.4 ext.lang TECWERK wurde für wiederholbare Entgratungs- und Anfaserprozesse entwickelt und ist aufgrund der Beschichtung und geometrischen Auslegung auf Serienbetrieb ausgelegt. Welche Spannfuttergröße wird empfohlen? Der Zylinderschaft mit Schaft-Ø 6 mm ermöglicht die Aufnahme in standardisierte Spannfutter mit entsprechendem Schaftdurchmesser; dadurch bleibt die Werkzeugaufnahme stabil auch bei längeren Ausführungen. Für welche Materialien ist der Entgrater geeignet? Der Entgrater ist aus Vollhartmetall gefertigt und eignet sich für viele Bearbeitungsaufgaben; die TiAlN-Beschichtung verbessert die Leistung bei erhöhten Schnitttemperaturen und schwer zerspanbaren Werkstoffen. Enthält die Artikelbezeichnung eine Werksnorm-Angabe? Ja, die Angabe Werksnorm weist auf die Fertigungs- und Qualitätsanforderungen hin, die bei der Herstellung des TECWERK Entgraters eingehalten werden. Hersteller: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a high-performance deburring solution that combines solid carbide construction, a TiAlN coating and an extra-long geometry for extended reach and tool life; order directly via Metav Werkzeuge or contact our consultants for tailored machining advice. Forward/Reverse Deburring Cutter D16 mm – Solid Carbide, TiAlN, 45° (TECWERK) The Forward/Reverse Deburring Cutter D16 mm is an extra-long solid-carbide chamfering and deburring tool designed for machine applications requiring precise bevels and reliable edge finishing Solid carbide, TiAlN-coated cutting head 45° chamfer angle for precise bevels Four flutes for smooth deburring and chips evacuation Extra-long design with 10 mm cylindrical shank Precision construction for consistent deburring performance Built from solid carbide and finished with a TiAlN coating, this cutter is engineered to provide consistent edge preparation and chamfering. The four-flute geometry balances cutting aggressiveness with a fine surface result, while the 45° chamfer angle is optimised for standard bevels and secure edge relief. Heat resistance from the coating reduces wear during continuous operation, so the tool maintains geometry longer and supports repeatable machining outcomes. The cutter is described in factory specification as extra long and features a cylindrical shank, enabling secure clamping in standard holders. Improved process efficiency and reduced rework An extra-long profile delivers access to recessed areas and extended component faces without compromising stability. The combination of a hardened substrate and surface coating lowers the frequency of tool changeovers, which positively affects throughput and overall tooling costs. By providing a cleaner initial edge finish, the cutter reduces secondary finishing operations and minimises scrap rates. These aspects present a clear economic case for integration into a production cell or precision workshop where reliable deburring and chamfering are essential to maintain cycle times and product quality. Straightforward integration and practical handling notes The cutter is supplied with a 10 mm shank diameter on a cylindrical shaft for straightforward mounting in collets and toolholders; compatibility with common clamping systems is ensured by this standard dimension. The extra-long design requires appropriate clamping depth to avoid deflection—secure clamping and correct speed/feed parameters extend tool life and preserve finish quality. For specifications such as ideal spindle speed and feed per tooth, technical parameters can be provided to match individual machine setups and component geometries. The tool is intended for forward and reverse deburring operations as well as chamfering, and its construction supports stable, repeatable results in typical machining workflows. For reliable chamfering and efficient deburring, consult Metav Werkzeuge for application-specific guidance and to arrange supply – contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000866619NW Product name: Forward/Reverse Deburring Cutter D16 mm Brand: TECWERK Packaging unit: 1 Facts Cutting diameter: 16 mm Shank diameter: 10 mm Number of flutes: 4 Chamfer angle: 45° Special features Solid carbide construction TiAlN coating Extra-long design Cylindrical shank For forward and reverse deburring and chamfering Factory standard (Werksnorm) FAQ What materials is this cutter intended for? The Forward/Reverse Deburring Cutter D16 mm (TECWERK) is specified for deburring and chamfering operations; material-specific recommendations and cutting data can be provided to match the intended workpiece. Can the extra-long design be used in deep geometric features? Yes, the extra-long geometry is intended for extended reach into recessed areas, provided the shank is clamped securely to avoid deflection. What advantages does the TiAlN coating offer? The TiAlN coating on this solid-carbide cutter improves heat resistance and wear protection, extending tool life under sustained machining conditions. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from the combination of solid carbide construction, TiAlN coating and an extra‑long geometry for precise chamfering and consistent deburring results; order the tool directly via Metav Werkzeuge or consult the advisers if technical support is required. TECWERK Forward/Reverse Deburring Tool D 4 mm – Solid Carbide, TiAlN, 45° A TECWERK Forward/Reverse Deburring Tool D 4 mm engineered for precision chamfering and burr removal in metalworking and finishing applications Solid carbide with TiAlN coating 4 mm cutting diameter, 45° chamfer Extra‑long geometry for deep edges 6 mm cylindrical shank, 4 flutes Consistent chamfers and reliable edge quality The design focuses on repeatable results: a 4 mm cutting diameter combined with a 45° cutting angle delivers uniform chamfers while the four‑flute geometry reduces vibration for a finer finish. The use of solid carbide provides dimensional stability under load and the TiAlN coating enhances surface hardness and heat resistance, prolonging cutting life under continuous operation. For machine shops requiring predictable component finishing, this tool balances precision and durability to reduce rework and ensure parts leave the bench with clean, deburred edges. Productivity gains through versatile cutting performance Built for both forward and reverse operations, the cutter’s extra‑long length gives access to recessed contours and hard‑to‑reach edges without compromising rigidity. The 6 mm cylindrical shank fits standard toolholders, enabling quick changeovers and straightforward integration into existing setups. The four‑flute geometry allows for balanced chip removal, supporting efficient cycle times and fewer stoppages for manual deburring. These characteristics translate into measurable improvements in throughput and a reduced need for secondary finishing operations. Practical integration and workshop support for confident use Selection and mounting are simplified by the tool’s compact shank and standard dimensions; maintenance consists of routine inspection and replacement when wear affects edge quality. Metav’s sourcing approach ensures consistent availability and a transparent supply chain, backed by decades of experience in precision tools. For teams making the transition from manual deburring to machine‑assisted finishing, the tool provides a technically straightforward route to higher consistency and less labour‑intensive post‑processing. Detailed technical advice is available for matching speeds and feeds to specific machines and setups. For reliable stock and specialist advice on the TECWERK forward/reverse deburring tool, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for ordering and technical consultation. Technical Data Article number / SKU: 2000866611NW Brand: TECWERK Packaging unit: 1 Facts Cutting diameter: 4 mm Shank diameter: 6 mm Angle: 45° Number of flutes: 4 Special features Material: Solid carbide Coating: TiAlN Geometry: Extra‑long Shank type: Cylindrical shank Application: Forward and reverse deburring, chamfering FAQ What materials is this deburring tool suitable for? The TECWERK forward/reverse deburring tool is designed for general metalworking deburring and chamfering tasks; for specific material recommendations and optimal cutting parameters, consult Metav Werkzeuge’s technical guidance. How does the TiAlN coating benefit workshop use? The TiAlN coating on the TECWERK cutter improves thermal resistance and surface hardness, extending the tool life and maintaining edge stability under elevated cutting temperatures. Can the tool be used in both forward and reverse directions? Yes, the cutter is specified for forward and reverse deburring and chamfering, offering flexibility for different machine setups and reversing operations. What shank size is required for mounting? A 6 mm cylindrical shank is standard on this tool, compatible with common collet and chuck systems used in precision finishing. Is this tool available in single pieces or sets? The item is supplied as a single unit (packaging unit 1); further purchasing options or stock availability can be confirmed through Metav Werkzeuge. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of solid carbide construction, TiAlN coating and an extra‑long design for consistently clean chamfers and reduced tool changes; order the Forward/Reverse Deburring Cutter directly via Metav Werkzeuge or consult our team for tailored advice. Forward/Reverse Deburring Cutter D 6 mm, Solid Carbide, TiAlN, 45° — TECWERK The Forward/Reverse Deburring Cutter D 6 mm, Solid Carbide, TiAlN, 45° (TECWERK) is an extra‑long, four‑flute cylindrical‑shank cutter designed for efficient chamfering and burr removal in machining operations Solid carbide construction for high stiffness and repeatability TiAlN coating for enhanced heat and wear resistance 45° cutting angle for precise chamfer geometry Extra‑long cylindrical shank Ø 6 mm for extended reach Accurate edges and consistent chamfering for reliable assembly The solid carbide body combined with a TiAlN‑coating and a true 45° cutting angle delivers reproducible chamfers and burr removal in both forward and reverse directions. The tool’s four‑flute geometry produces stable cutting forces and a fine edge finish, which reduces secondary operations and ensures parts fit and function as intended. Designed with an extra‑long cylindrical shank Ø 6 mm, the cutter reaches confined features while maintaining concentricity and run‑out resistance, supporting consistent results across series production and small batches alike. Improved uptime and predictable tool life for efficient production A robust, coated carbide design minimises wear and helps maintain cutting geometry over longer cycles, contributing to longer tool life and fewer tool changes. The TiAlN layer increases resistance to thermal loading and abrasive wear, which is particularly valuable when process windows are narrow and interruptions are costly. By reducing unexpected downtime and smoothing the tool change rhythm, the cutter supports leaner machining flows and a clearer cost‑benefit balance for workshop and production planners. Practical integration into existing toolsets and procurement workflows The cylindrical shank with a 6 mm diameter matches common collets and holders, enabling quick integration into standard toolholders without extra adapters. The cutter’s straight‑forward specification simplifies tool selection and inventory management, while Metav Werkzeuge’s range and logistics ensure dependable supply from Emmerich. Backed by a partner with a broad catalogue and established market trust, quality assurance becomes part of the procurement process rather than an extra burden — a pragmatic step towards predictable manufacturing outcomes. For dependable chamfering and efficient deburring choose TECWERK’s solution and contact Metav Werkzeuge for precise availability and ordering: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000866613NW Label: Forward/Reverse Deburring Cutter D 6 mm, Solid Carbide, TiAlN, 45° — TECWERK Manufacturer: TECWERK Facts Shaft diameter: 6 mm Cutting angle: 45° Number of flutes: Z = 4 Packaging unit: 1 Special features Solid carbide (VHM) TiAlN coating Four‑flute design (Vierschneider) Extra‑long version Cylindrical shank FAQ What operations is this cutter intended for? The cutter is designed for forward and reverse deburring as well as for chamfering; the product designation Forward/Reverse Deburring Cutter D 6 mm, Solid Carbide, TiAlN, 45° (TECWERK) specifies those intended uses. How does the TiAlN coating benefit the tool? The TiAlN coating on this TECWERK cutter increases heat and wear resistance, which helps to maintain cutting geometry and extend the service life under industrial machining conditions. Does the shank fit standard toolholders? Yes — the cylindrical shank with a diameter of 6 mm is specified to match common collets and holders, allowing simple installation in existing tool assemblies. What kind of edge finish can be expected with a four‑flute geometry? A four‑flute configuration offers stable cutting and a fine finish during deburring and chamfering, producing consistent chamfer geometry and reducing the need for manual rework. Which identifier should be used when ordering or checking stock? Reference the article number 2000866613NW when enquiring about availability or placing orders for this TECWERK cutter. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

VHM · TiAlN-beschichtet · Werksnorm · Vierschneider · 45 ° Winkel · extra lang · Zylinderschaft · zum Vor- und Rückwärtsentgraten sowie zum Anfasen Weitere technische Eigenschaften: · Schaft-Ø: 6mm

VHM · TiAlN-beschichtet · Werksnorm · Vierschneider · 45 ° Winkel · extra lang · Zylinderschaft · zum Vor- und Rückwärtsentgraten sowie zum Anfasen Weitere technische Eigenschaften: · Schaft-Ø: 6mm