50mm Face Milling Cutter HSS-Co5 TiCN 8 Teeth Right-Hand DIN 1880 - TECWERK

Take advantage of the combination of HSS‑Co5 substrate, TiCN coating and an 8‑tooth geometry for improved tool life and consistent face milling results; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations.

Face milling cutter DIN 1880 Type NR, 50 mm, HSS‑Co5, TiCN, 8 teeth (TECWERK)

A face milling cutter DIN 1880 Type NR designed for high‑precision machining of structural and heat‑treated steels as well as short‑chipping non‑ferrous alloys.

• DIN 1880 compliant design
• 50 mm diameter for compact machining
• HSS‑Co5 substrate for wear resistance
• TiCN coating for extended tool life

Engineered for efficient material removal and longer tool life

The cutter combines a HSS‑Co5 base material with a TiCN coating, delivering a balance between toughness and wear resistance that suits interrupted and continuous face milling. The 8 cutting edges spread the cutting load, allowing higher material removal rates with reduced heat buildup. Compared with uncoated high‑speed steel, the carbonitride layer improves resistance to abrasive wear and extends the interval between regrinds, which supports cost‑effective production runs and predictable process planning.

Profile and groove geometry for reliable chip control and surface quality

A relieved cord profile with integrated longitudinal and transverse grooves (to DIN 138) optimises chip formation and evacuation. The combination of the specialised profile and the groove pattern reduces a tendency for long swarf and supports short, controllable chips when machining non‑ferrous, short‑chipping materials. This results in a consistently improved surface finish and reduces the risk of rework; operators benefit from simplified handling of swarf and fewer interruptions during multi‑piece routines.

Application scope: steels and short‑chipping non‑ferrous metals

The tool is specified for machining structural steels, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals. Right‑hand cutting geometry and the selected substrate/coating pairing make it suitable for conventional face milling tasks where a balance of edge stability and wear resistance is required. Process planners and workshop managers can expect repeatable results in component families where throughput and reliable edge life are priorities.

Mounting and compatibility for industrial setups

The cutter adheres to DIN 1880 dimensional standards and features a 22 mm bore for standard arbour mounting, ensuring compatibility with many existing holders and adaptors used in machining centres and milling heads. The compact 50 mm diameter and the tool’s standardised interface simplify integration into existing tool sets, reducing setup times and enabling rapid changeover between operations.

For tailored advice on employing this TECWERK face milling cutter in specific materials and to secure dependable supply from Metav Werkzeuge, contact our Emmerich team by email or phone for expert guidance and fast delivery.

Technical data

• Article number: 2000866650NW
• Standard: DIN 1880
• Product type: Face milling cutter
• Manufacturer: TECWERK

Facts

• Diameter: 50 mm
• Cutting length: 8 mm
• Teeth: 8
• Bore diameter: 22 mm
• Width: 36 mm

Special features

• Material: HSS‑Co5
• Coating: TiCN
• Right‑hand cutting
• Type NR
• Relieved cord profile
• Longitudinal and transverse grooves to DIN 138
• For structural, case‑hardened and quenched/tempered steels; short‑chipping non‑ferrous metals

FAQ

What materials can this cutter machine effectively?
The TECWERK face milling cutter is specified for structural steels, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals, making it versatile for mixed‑material production.

How does the TiCN coating influence performance?
The TiCN coating on the HSS‑Co5 substrate increases surface hardness and wear resistance, extending cutting edge life and improving performance under elevated temperatures.

Is the cutter compatible with standard DIN 1880 arbour systems?
Yes, the tool conforms to DIN 1880 dimensions and the 22 mm bore allows mounting on common arbour systems used for Type NR face mills.

How many cutting edges does the tool feature and what is the benefit?
The cutter has 8 cutting edges, which distribute cutting forces and reduce per‑edge load, supporting smoother cuts and longer service intervals.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund