Take advantage of the combination of DIN 1880 standardisation, HSS‑Co5 material and 8 flutes for consistent, high‑performance milling in mixed workshop environments; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK cylindrical face mill DIN 1880 Type N, 40 mm — HSS‑Co5, 8 flutes The TECWERK cylindrical face mill DIN 1880 Type N, 40 mm is a robust cutter designed for machining structural and heat-treated steels as well as short‑chip non‑ferrous materials in general workshop and light industrial production. HSS‑Co5 for enhanced heat resistance DIN 1880 Type N for standardised mounting 8 flutes for uniform material removal Longitudinal and cross slots for chip evacuation Consistent cutting performance for mixed materials The combination of HSS‑Co5 (high‑speed steel with 5% cobalt) and a set of 8 flutes delivers a balance of toughness and cutting stability that is especially valuable when alternating between structural steels and short‑chip non‑ferrous metals. The cobalt‑alloyed steel improves hot hardness and wear resistance, which preserves cutting geometry under thermal load and extends tool life. This results in precise surface finishes and fewer tool changes during batch runs, supporting a reliable production rhythm. Built‑in chip control reduces interruptions and rework Designed with both longitudinal and transverse slots in accordance with DIN 138, the cutter promotes fast chip evacuation, preventing chip recutting and heat build‑up at the cutting edge. Efficient chip flow lowers the risk of surface damage and reduces the need for secondary operations, so machining cycles remain economical and predictable. The right‑hand cutting geometry further stabilises chip formation for conventional milling directions. Standardised dimensions for simple integration and replacement Compliance with DIN 1880 Type N ensures predictable mounting and interchangeability in existing toolholders. The cutter’s 40 mm diameter and 16 mm bore allow straightforward mounting on compatible arbors, saving set‑up time when replacing worn tools. Standardised form and dimensions mean spare tooling can be stocked and rotated efficiently, supporting continuous machine uptime and simplified inventory management. Durability and workshop benefits that matter day to day The mill’s construction emphasises robustness and low maintenance: the cobalt‑enriched substrate resists thermal softening, while the multiple cutting edges distribute wear evenly, prolonging service intervals. For workshops producing components from construction, case‑hardened and quenched‑and‑tempered steels as well as short‑chip non‑ferrous alloys, the design reduces chatter and maintains dimensional stability, which in turn decreases scrap rates and improves throughput. Contact Metav Werkzeuge for tailored application advice and to secure the TECWERK cylindrical face mill that suits specific machining needs — Metav Werkzeuge provides fast, reliable supply from Emmerich. Technical Data Article number: 2000866620NW Product type: Cylindrical face mill (Walzenstirnfräser) Brand: TECWERK Standard: DIN 1880 Key measurements Diameter: 40 mm Width: 32 mm Cutting length: 8 mm Bore diameter: 16 mm Number of flutes: 8 Special features Material: HSS‑Co (high‑speed steel with cobalt) DIN 1880 Type N Longitudinal and cross slots per DIN 138 Right‑hand cutting Suitable for structural, case‑hardened and quenched‑and‑tempered steels and short‑chip non‑ferrous metals Packaging unit: 1 FAQ What materials is the cutter suited for? The TECWERK cylindrical face mill is specified for machining structural, case‑hardened and quenched‑and‑tempered steels, as well as short‑chip non‑ferrous metals, offering versatility across common workshop materials. How does the HSS‑Co5 substrate affect tool life? The HSS‑Co5 composition increases hot hardness and wear resistance, so the cutter maintains cutting geometry longer under elevated temperatures and abrasive conditions than plain high‑speed steel. Is this cutter compatible with standard DIN 1880 toolholders? Yes — the cutter conforms to DIN 1880 Type N, which ensures compatibility with matching arbors and holders designed for this standard; the 16 mm bore is a common mounting dimension. What advantage do the longitudinal and cross slots provide? Longitudinal and cross slots, manufactured to DIN 138 guidance, promote controlled chip evacuation, reducing the likelihood of chip packing and improving surface quality during continuous machining. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of robust HSS‑Co5 construction, a 40 mm diameter with 7 cutting edges, and DIN‑based geometry for reliable, repeatable milling results; order the cutter directly via Metav Werkzeuge or consult our technical team for application support. Cylindrical face mill DIN 1880 Type HR, 40 mm, HSS‑Co5 — TECWERK The Cylindrical face mill DIN 1880 Type HR is a right‑hand cutting, HSS‑Co tool designed for milling construction, case‑hardened and quenched & tempered steels, plus short‑chipping non‑ferrous metals. HSS‑Co5 construction for high hot hardness DIN 1880 Type HR for standardised mounting Seven cutting edges for smooth material removal Longitudinal and transverse flutes per DIN 138 High‑performance material and tool life for demanding production The Walzenstirnfräser DIN 1880 Typ HR combines a HSS‑Co5 substrate with a compact geometry to offer elevated red‑hardness and wear resistance compared with standard high‑speed steels. For users working in small series or demanding workshop environments, this composition means more consistent cutting life and fewer tool changes; the result is increased uptime and lower tooling handling overhead. The material choice is particularly advantageous when temperatures rise at the cutting zone, because cobalt improves hardness retention under heat. Geometry engineered for clean chips and stable cutting The cutter’s relief‑ground cord profile and the integrated longitudinal and transverse flutes (DIN 138) promote controlled chip formation and efficient evacuation, which reduces the risk of recutting and improves surface finish. With a 40 mm diameter and 7 cutting edges, the geometry is optimised for stable engagement and balanced cutting forces; the moderate 7 mm cutting length suits shallow face and shoulder milling where precision and repeatability matter. Compliance with DIN 1880 ensures compatibility with standard tool holders and predictable mounting concentricity. Practical suitability and workshop benefits Designed as a right‑hand cutting tool with a 16 mm bore, the cutter is suitable for conventional milling spindles and compact toolholders common in job‑shop and production settings. Its specification targets construction steels, case‑hardened and quenched & tempered steels, as well as short‑chipping non‑ferrous metals, delivering a balance between versatility and focused performance. The straightforward geometry and standardised interface make it a pragmatic choice for buyers seeking a reliable, easy‑to‑integrate cutter that keeps cycle times efficient and setups consistent. For tailored technical advice or to confirm suitability for a specific application, request availability and detailed recommendations for the TECWERK cylindrical face mill from Metav Werkzeuge — Metav Werkzeuge can supply further data sheets and delivery options for immediate planning Technical data Article number: 2000866660NW Label: Walzenstirnfräser DIN 1880 Typ HR D.40mm HSS‑Co5 Z.7 TECWERK Standard: DIN 1880 Manufacturer: TECWERK Facts Diameter: 40 mm Cutting edges: 7 Cutting length: 7 mm Bore diameter: 16 mm Cutting direction: right‑hand Special features Material: HSS‑Co (cobalt‑alloyed high‑speed steel) Type: DIN 1880 Type HR Relief‑ground cord profile Longitudinal and transverse flutes per DIN 138 Suited for construction, case‑hardened and quenched & tempered steels Suitable for short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The TECWERK cylindrical face mill (Walzenstirnfräser DIN 1880 Type HR, SKU 2000866660NW) is specified for construction steels, case‑hardened and quenched & tempered steels, and short‑chipping non‑ferrous metals. Which standard and type does the tool follow? The cutter complies with DIN 1880 and is manufactured as Type HR to ensure standardised mounting and interchangeability. How many cutting edges and what diameter does the cutter have? This tool features 7 cutting edges and a 40 mm diameter; the cutting length is 7 mm and the bore diameter is 16 mm. What material is the tool made from and why is that important? The cutter is made from HSS‑Co5 (cobalt‑alloyed high‑speed steel), which improves hot hardness and wear resistance compared with plain HSS, beneficial for elevated cutting temperatures. Is the cutter right‑hand or left‑hand cutting? The cutter is right‑hand cutting, designed for conventional clockwise spindle rotation during milling. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co5 tool steel, DIN 1880 standard geometry and a compact 40 mm diameter with seven cutting edges for consistent face milling performance; order directly via Metav Werkzeuge or request advice from our consultants. Face mill DIN 1880 Type NR, 40 mm, HSS‑Co5 — TECWERK The Face mill DIN 1880 Type NR is a compact, right‑hand face milling cutter designed for machining construction, case‑hardened and quenched steels, as well as short‑chipping non‑ferrous metals in general production environments HSS‑Co5 grade for high wear resistance DIN 1880 Type NR standardised geometry 7 cutting edges for smooth material removal Right‑hand cutting for conventional milling Consistent results from standardised cutter geometry The cutter is built to DIN 1880, which prescribes a reproducible geometry for face milling tools. This standardisation delivers predictable contact conditions and a uniform surface finish across repeated operations. The HSS‑Co5 material provides improved hardness and heat resistance compared with conventional high‑speed steels, which means sustained cutting performance under continuous load. With a compact 40 mm diameter and seven flutes, the tool balances stability and material removal rate for short to medium engagement passes. Geometry and chip control that support efficient cycles A relief‑ground cord profile combined with longitudinal and transverse grooves to DIN 138 helps produce short, controllable chips during machining. This geometry reduces the risk of built‑up edge on short‑chipping non‑ferrous metals and improves evacuation when cutting common structural and treated steels. The result is reduced rework and fewer interruptions for chip clearing, which translates into measurable productivity gains on mixed‑material production lists. Straightforward mounting and integration into existing toolsets Mounting is facilitated by a 16 mm bore compatible with standard arbors for small face mills, enabling quick changeover and secure clamping without complex adaptors. The cutter’s 7 cutting edges and 7 mm cutting length are optimised for shallow face milling and finishing passes, offering a good compromise between chip thickness and tool life. The right‑hand cutting orientation suits conventional milling set‑ups and standard machine tool spindle directions. Robust construction for demanding shop use Constructed from a cobalt‑alloy high‑speed steel, this cutter withstands the thermal and mechanical stresses of continuous production. The material choice and the tool’s profile make it particularly appropriate for construction steels, case‑hardened and quenched steels as well as short‑chipping non‑ferrous metals, providing long tool life and stable cutting behaviour. The combination of HSS‑Co5 construction and DIN conformity supports predictable reconditioning intervals and inventory planning. For reliable face milling with TECWERK’s HSS‑Co5 cutter, contact Metav Werkzeuge for technical advice and fast supply directly from Emmerich Technical Data Article number: 2000866640NW Label: Walzenstirnfräser DIN 1880 Typ NR D.40mm HSS‑Co5 Z.7 TECWERK Manufacturer: TECWERK Product type: Walzenstirnfräser Standard: DIN 1880 Core data Diameter: 40 mm Cutting length: 7 mm Teeth: 7 Bore diameter: 16 mm Packaging unit: 1 Special features Material: HSS‑Co (HSS‑Co5) Cutting direction: right‑hand cutting Relief‑ground cord profile Longitudinal and transverse grooves to DIN 138 Suitable for construction, case‑hardened and quenched steels Suitable for short‑chipping non‑ferrous metals FAQ What materials is this face mill suitable for? The face mill is designed for machining construction steels, case‑hardened and quenched steels, and short‑chipping non‑ferrous metals as stated for the TECWERK face mill (SKU 2000866640NW). How is the cutter mounted in a production arbor? The cutter features a 16 mm bore for direct mounting to compatible arbors; the 16 mm bore size ensures secure clamping for the intended small‑diameter face milling operations. What does conformity to DIN 1880 mean for production planning? DIN 1880 conformity indicates standardised geometry and interchangeability, allowing predictable cutting behaviour and easier tool replacement planning when using the TECWERK DIN 1880 Type NR cutter. How many cutting edges and what cutting length does the tool have? The tool has 7 cutting edges with a cutting length of 7 mm, which is suited to shallow face milling and finishing passes where controlled chip formation is required. Is this cutter suitable for conventional right‑hand milling set‑ups? Yes, the cutter is specified as right‑hand cutting and is intended for conventional spindle directions and standard milling configurations. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co5 construction, a TiCN coating and a 7‑tooth geometry for durable, high‑feed milling in workshop and production environments; the result is reliable material removal and predictable tool life. Order directly via Metav Werkzeuge or consult the team for application advice. TECWERK cylindrical face mill (DIN 1880, Type NR) — 40 mm, HSS‑Co5, TiCN The TECWERK cylindrical face mill (Type NR) is a robust, right‑hand cutting tool engineered for high‑efficiency milling of construction, case‑hardened and quenched steels as well as short‑chipping non‑ferrous metals. TiCN coating for extended tool life HSS‑Co5 construction for increased toughness 7 flutes for steady chip load Right‑hand cutting, DIN 1880 compliant Consistent high performance and measurable uptime The cutter’s HSS‑Co5 substrate combined with a TiCN surface layer delivers a balance of toughness and wear resistance that extends service intervals. The 7‑tooth geometry reduces per‑tooth load, which stabilises cutting forces and helps maintain surface finish on rougher castings or harder quenched parts. For production planners this translates into longer tool cycles and fewer unscheduled tool changes, improving machine utilisation and lowering unit costs. Versatile material capability for mixed production runs Designed with a DIN 1880 Type NR profile and a relieved cord‑style cutting edge, the tool is suited to machining construction steels, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals such as aluminium alloys. The incorporated longitudinal and transverse slots (to DIN 138) aid chip evacuation when cutting aluminium or brass, while the cobalt‑alloyed high‑speed steel substrate resists thermal softening during interrupted cuts. This versatility reduces the need for tool changes across mixed batches. Improved chip control and surface quality The combination of the cutter’s flute count and the optimised profile ensures predictable chip control and steady surface generation. The right‑hand cutting orientation and the precise tooth geometry produce regular chip formation, which lowers rework rates and minimises secondary finishing. Where part tolerances demand repeatable finishes, this milling solution offers the stability required for consistent downstream assembly or coating processes. Practical handling, mounting and workshop integration With a 40 mm diameter and a 16 mm bore, the tool fits compact machining envelopes while remaining compatible with common arbor systems; the HSS‑Co5 body tolerates modest shock loads better than carbide in some interrupted milling tasks. The cutter’s construction is straightforward to inspect and regrind where appropriate, enabling refurbishment in vocational workshops and small series production. Metav’s Emmerich distribution ensures rapid supply, clear provenance and traceable quality for engineering teams. For application guidance or to procure this TECWERK cylindrical face mill from Metav Werkzeuge, contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 for direct delivery and technical support from Emmerich. Technical data Article number: 2000866648NW Product type: cylindrical face mill Brand: TECWERK Standard: DIN 1880 Diameter: 40 mm Width: 32 mm Number of flutes: 7 Cutting length: 7 mm Bore diameter: 16 mm Material: HSS‑Co Coating: TiCN Cutting direction: right‑hand cutting Design note: Type NR, relieved cord profile; longitudinal and transverse slot to DIN 138 Application: machining construction, case‑hardened and tempered steels; short‑chipping non‑ferrous metals FAQ What materials is the cutter suitable for? The TECWERK cylindrical face mill is suitable for construction steels, case‑hardened and tempered steels and short‑chipping non‑ferrous metals as stated in the product specification. How does the TiCN coating benefit the tool? The TiCN coating increases wear resistance and reduces built‑up edge, helping the cutter maintain performance over longer cycles compared with uncoated high‑speed steel. Can the cutter be reground or resharpened? The HSS‑Co5 substrate permits regrinding of the cutter geometry where permitted by the original profile and workshop capabilities; consult the reconditioning guidelines before proceeding. Which standard and type does this cutter follow? This tool conforms to DIN 1880, Type NR, ensuring compatibility with equipment and mounting practices that reference this standard. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a combination of HSS‑Co5 construction and a TiCN surface, which delivers extended tool life and consistent machining results; order the cutter directly via Metav Werkzeuge or consult the team for application advice. Cylindrical face milling cutter DIN 1880 Type HR, 40 mm – HSS‑Co5, TiCN (TECWERK) The Cylindrical face milling cutter DIN 1880 Type HR is a compact, right‑hand cutting face mill engineered for efficient machining of steels and short‑chipping non‑ferrous metals HSS‑Co5 core for high wear resistance TiCN coating for extended tool life 7 cutting edges for efficient material removal Bore Ø16 mm, DIN 1880 Type HR Consistent cutting performance through material and coating Constructed from HSS‑Co5, this face mill offers a robust cutting core that resists abrasive wear while maintaining toughness during interrupted cuts. The TiCN coating reduces friction and increases resistance to built‑up edge, which results in longer intervals between tool changes and more uniform surface finishes. Compliance with DIN 1880 signals dimensional consistency, making the tool suitable for standardised setups and reliable repeatability in production environments. Improved chip control and stable machining cycle The tool’s 7 cutting edges and its right‑hand cutting geometry deliver balanced material removal and steady cutting forces. The combination of longitudinal and transverse slots manufactured to DIN 138 promotes controlled chip evacuation and reduces the risk of recutting, which preserves workpiece quality and tool life. The cutter’s Bore Ø16 mm ensures compatibility with common arbor systems, giving a compact, rigid connection that supports vibration damping and dimensional stability during milling. Targeted applications that reduce rework and increase throughput Designed for machining structural steels, case‑hardening and tempered steels, as well as short‑chipping non‑ferrous alloys, the cutter targets tasks where reliable edge life and surface consistency matter. The undercut chordal profile improves entry behaviour and reduces cutting forces on interrupted surfaces, minimising the need for secondary finishing. The TECWERK face mill is therefore a practical choice for job shops and production lines seeking dependable, repeatable results from a compact face milling solution. Contact Metav Werkzeuge for tailored advice on TECWERK cutting tools and to secure this HSS‑Co5 TiCN face milling cutter for the workshop — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: 2000866668NW Product type: Cylindrical face milling cutter Standard: DIN 1880 Manufacturer: TECWERK Facts Diameter: 40 mm Cutting edges: 7 Bore diameter: 16 mm Cutting length: 7 mm Special features Material: HSS‑Co5 Coating: TiCN Right‑hand cutting Undercut chordal profile Longitudinal and transverse slots to DIN 138 Suited to structural, case‑hardening and tempered steels and short‑chipping non‑ferrous metals FAQ What materials can this face milling cutter machine? The TECWERK cylindrical face milling cutter is intended for structural steels, case‑hardening and tempered steels, and for short‑chipping non‑ferrous metals as stated in the product details. How does the TiCN coating benefit machining? The TiCN coating on this HSS‑Co5 cutter reduces friction and wear, increasing tool life and improving surface finish during continuous and interrupted milling cycles. Which standards does the cutter comply with? The cutter conforms to DIN 1880 for the tool type and incorporates slots produced to DIN 138, ensuring dimensional compatibility with standard tooling systems. Is the cutter suitable for interrupted cuts or heavy engagement? The combination of HSS‑Co5 construction, the undercut chordal profile and the balanced 7‑edge geometry provides stability and resistance to shock, making it suitable for many interrupted cut scenarios. What arbor or mounting is required? The cutter features a bore of Ø16 mm; matching arbors with a 16 mm arbor fit are appropriate for secure mounting and stable operation. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of robust material construction, precise DIN-conforming geometry and a wear-resistant TiCN coating to keep production reliable and minimise downtime — order the TECWERK tool directly via Metav Werkzeuge or consult our specialists for application-specific guidance. Cylindrical face cutter DIN 1880 Type N, 40 mm, HSS‑Co5, TiCN, Z=8 (TECWERK) A Cylindrical face cutter DIN 1880 Type N engineered for medium-duty milling of steels and short‑chipping non‑ferrous metals in industrial and workshop environments. TiCN coating for improved wear resistance HSS‑Co5 substrate for high toughness 40 mm diameter, 8 cutting edges Conforms to DIN 1880, Type N geometry Consistent metal removal with tough HSS‑Co5 and TiCN protection The combination of a HSS‑Co5 substrate and a TiCN surface finish delivers a balance of toughness and wear resistance that suits interrupted cuts and frequent tool engagement. The tool’s hardened high‑speed steel base resists chipping under load, while the titanium carbonitride layer reduces adhesive wear and extends edge life. Designed as a medium‑sized milling cutter, the 40 mm diameter and eight flutes provide a steady material removal rate and help maintain dimensional stability in series work, making it a pragmatic choice for machine shops that prioritise throughput and predictable tool life. Geometry tailored for reliable surface finish and chip control Built to the DIN 1880 standard with Type N geometry and equipped with longitudinal and transverse grooves per DIN 138, the cutter ensures controlled chip formation and evacuation. The eight cutting edges balance cutting load and surface smoothing, reducing vibration and producing a consistent finish across the machined face. The right‑hand cutting orientation suits standard milling setups and contributes to predictable tool behaviour. For users less familiar with these norms: Type N indicates a typical cylindrical face milling profile optimised for a broad range of steels and short‑chip non‑ferrous alloys. Practical integration into arbor systems and application range The tool features a 16 mm bore for mounting on compatible arbors, enabling secure clamping and concentric performance in common milling adapters. Intended applications include structural, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals; the combination of substrate and coating reduces the need for frequent tool changes in mixed‑batch production. Maintenance is straightforward: when wear compromises edge quality, regrinding or replacement restores performance. For specification checks or to ensure compatibility with a particular arbor or machining strategy, Metav Werkzeuge provides technical guidance and fast delivery from Emmerich. Choose the TECWERK TiCN‑coated cylindrical face cutter for sustained productivity — contact Metav Werkzeuge for tailored machining advice and reliable supply from Emmerich (info@metav-werkzeuge.com, +49 2822 7131930) Technical data Article number: 2000866628NW Brand: TECWERK Standard: DIN 1880 Facts Diameter: 40 mm Cutting length: 8 mm Number of cutting edges: 8 Bore diameter: 16 mm Width: 32 mm Special features Material: HSS‑Co5 Coating: TiCN Geometry: Type N according to DIN 1880 Flutes: Longitudinal and transverse groove per DIN 138 Cutting direction: Right‑hand cutting Application: Milling of structural, case‑hardened and tempered steels; short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The cylindrical face cutter, produced by TECWERK, is intended for structural steels, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals and performs well where a HSS‑Co5 substrate and TiCN coating are advantageous. How is the tool mounted in a milling arbor? Mounting uses the 16 mm bore; the TECWERK face cutter should be fitted to a matching arbor or adapter that secures the cutter concentrically for stable performance. What does Type N and DIN 1880 mean for machining? Type N refers to a standard cylindrical face milling geometry under DIN 1880, which specifies cutter form and tolerances to ensure consistent chip control and surface finish across compatible cutters. Can this cutter be used for interrupted cuts? Yes, the HSS‑Co5 substrate combined with the TiCN coating is selected to tolerate the shock of interrupted cuts and to resist premature edge failure in typical workshop conditions. How many teeth does the cutter have and why does that matter? The tool has eight cutting edges; more cutting edges spread the load and can improve surface finish while influencing feed per tooth and chip thickness in the chosen machining strategy. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust combination of HSS‑Co5 cutting material and DIN‑1880 conformity for stable, repeatable face milling results; the Type NR geometry with relieved profile and integrated grooves ensures reliable chip control and surface quality. Order or request advice directly via Metav Werkzeuge for procurement and application support. Cylindrical face milling cutter DIN 1880 – Type NR, Ø50 mm, HSS‑Co5 (Z=8) by TECWERK The Cylindrical face milling cutter DIN 1880 Type NR is a compact, DIN‑standard cutter designed for precision face and peripheral milling in demanding workshop and industrial environments HSS‑Co5 high‑cobalt high‑speed steel Conforms to DIN 1880 Type NR Ø50 mm diameter, 8 cutting edges Longitudinal and cross grooves (DIN 138) High material resilience for continuous production performance Made from HSS‑Co5, this cutter combines enhanced red‑hardness with good toughness, which translates into longer tool life under elevated temperatures and intermittent loading. The DIN 1880 standard ensures compatibility with existing DIN‑conforming toolholders and arbors, reducing setup time and variance between batches. With a compact Ø50 mm body and 8 cutting edges, the design balances metal removal rate and surface finish, supporting steady-state machining where predictable cycle times are essential. Precision geometry for improved chip control and surface quality The ground relieved profile of the teeth reduces cutting forces and helps maintain a consistent contact zone, supporting improved surface results on plain and alloyed steels. Integrated longitudinal and transverse grooves manufactured to DIN 138 assist chip evacuation and coolant distribution, which is especially beneficial when working with short‑chipping non‑ferrous metals. These features together lower the risk of built‑up edge and help achieve a cleaner finish with fewer downstream operations. Broad applicability across steels and short‑chipping non‑ferrous metals Thanks to the specified cutting geometry and material, the cutter is suitable for milling structural steels, case‑hardening steels and quenched‑and‑tempered grades, as well as short‑chipping non‑ferrous metals that benefit from positive chip formation. The right‑hand cutting orientation and solid construction support conventional milling setups. The combination of properties makes the tool a practical choice for production workshops and jobbing environments where a single cutter must cover multiple workpiece materials. Installation compatibility and workshop efficiency A nominal 22 mm bore permits mounting on a range of standard arbors, while the modest outer diameter and compact cutting length promote easy integration into existing tool sets. Supplied as a single unit, the cutter simplifies inventory management and reduces the number of specialised tools required. Metav's distribution from Emmerich ensures transparent order handling and dependable supply for routine reordering, supporting uninterrupted shop‑floor operations. Contact Metav Werkzeuge for procurement advice on the TECWERK DIN 1880 Type NR cylindrical face milling cutter (SKU 2000866642NW) and to confirm suitability for specific materials and setups Technical data Article number: 2000866642NW SKU: 2000866642NW Brand: TECWERK Standard: DIN 1880 Numbers / Facts Diameter: 50 mm Number of cutting edges: 8 Cutting length: 8 mm Bore diameter: 22 mm Width: 36 mm Special features / Versions Material: HSS‑Co5 Type NR geometry Relieved profile for improved cutting Longitudinal and transverse groove to DIN 138 Right‑hand cutting Packaging unit: 1 FAQ What materials can this cutter machine effectively? The cylindrical face milling cutter (TECWERK, Type NR, SKU 2000866642NW) is specified for structural steels, case‑hardening steels, quenched‑and‑tempered grades and short‑chipping non‑ferrous metals. Which standards and profiles does the tool comply with? The tool conforms to DIN 1880 and features grooves manufactured to DIN 138, ensuring compatibility and standardised chip‑control geometry. How many cutting edges does the cutter have and what material is it made from? This TECWERK cylindrical face milling cutter has 8 cutting edges and is made from HSS‑Co5 high‑cobalt high‑speed steel. What arbor or bore size is required for mounting? The cutter uses a 22 mm bore and is suitable for arbors and holders that accept this nominal mounting diameter. Is this cutter suitable for workshop production runs? Yes; the DIN conformity, HSS‑Co5 construction and the Type NR geometry make the cutter suitable for repeatable workshop production where consistent surface quality and tool life are required. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co5 tool steel, a 50 mm cutting diameter and a relieved profile to achieve reliable material removal and long service life in batch production. Order the cutter directly via Metav Werkzeuge or contact our consultants for application-specific advice. Cylindrical face mill DIN 1880, 50 mm (TECWERK) — HSS‑Co5, 8 cutting edges Cylindrical face mill DIN 1880, 50 mm designed for right‑hand milling of construction and alloy steels as well as short‑chipping non‑ferrous metals HSS‑Co5 construction for high strength DIN 1880 compliant profile 8 cutting edges for efficient material removal Right‑hand cutting, suitable for steel and non‑ferrous Reliable cutting performance for demanding materials The TECWERK cylindrical face mill combines a HSS‑Co5 matrix with an engineered geometry to deliver dependable performance when machining demanding steels. The addition of cobalt increases hot hardness and wear resistance, which enables stable cutting at elevated temperatures and prolongs tool life compared with standard high‑speed steel. This results in fewer interruptions for tool changes, predictable productivity and lower per‑part tooling costs in medium‑run production. Engineered geometry for consistent chip control and surface finish A relieved chord profile with longitudinal and transverse grooves (DIN 138) and 8 cutting edges creates controlled chip formation and evacuation. The tool’s 8‑tooth arrangement balances material removal rate and surface quality, while a cutting length of 8 mm ensures effective engagement on the workpiece. The result is reduced risk of built‑up edge and more consistent finishes on components made from short‑chipping non‑ferrous materials and a range of steels. Standards compatibility for straightforward integration in the workshop Designed to DIN 1880, the cutter fits common arbors and mounting systems and is provided with a 22 mm bore for secure attachment. The 50 mm overall diameter and right‑hand cutting orientation match typical machining setups, so the tool is immediately deployable in existing setups without special adapters. The mill is particularly suitable for milling construction steels, case‑hardened and quenched‑and‑tempered grades, as indicated by the tool’s application profile, and it performs reliably where short chips are expected. Contact Metav Werkzeuge for detailed mounting information or to specify the TECWERK cylindrical face mill with HSS‑Co5 for current production needs — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000866662NW Designation: Walzenstirnfräser DIN 1880 Typ HR D.50mm HSS‑Co5 Z.8 TECWERK Facts Diameter: 50 mm Cutting length: 8 mm Bore diameter: 22 mm Cutting edges: 8 Cutting direction: right‑hand Packaging unit: 1 Features Material: HSS‑Co (HSS‑Co5) Standard: DIN 1880 Relieved chord profile (hinterschliffenes Kordelprofil) Longitudinal and transverse grooves to DIN 138 Application: construction, carburised and quenched‑tempered steels; short‑chipping non‑ferrous metals FAQ What materials is the cutter suitable for? The TECWERK cylindrical face mill (Walzenstirnfräser DIN 1880) is specified for construction steels, carburised and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals. Which mounting bore is required for this cutter? This cutter requires a 22 mm bore for mounting; the 22 mm dimension is stated on the TECWERK product data (SKU 2000866662NW). How does HSS‑Co5 benefit machining performance? HSS‑Co5 increases hot hardness and wear resistance compared with standard HSS, so the TECWERK cutter maintains cutting edge stability for longer at higher temperatures. Is the cutter compatible with DIN standards? Yes, the tool is manufactured to DIN 1880 and includes longitudinal and transverse grooves to DIN 138, ensuring interchangeability and predictable fitment. Can the cutter handle finishing and semi‑roughing operations? The combination of tool geometry and 8 cutting edges makes the cutter suitable for operations that demand good surface finish while maintaining an efficient material removal rate. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Combine heat-resistant HSS‑Co5 construction with a 50 mm diameter and 8 flutes to deliver stable material removal and extended tool life for mixed-steel production. The DIN 1880 Type N geometry ensures straightforward integration into standard setups. Order the TECWERK cylindrical face mill directly via Metav Werkzeuge or ask our consultants for tailored application support. TECWERK Cylindrical Face Mill (DIN 1880 Type N) – 50 mm, HSS‑Co5, 8 flutes The TECWERK cylindrical face mill is a Type N DIN 1880 tool designed for general-purpose milling of structural, case-hardened and quenched steels as well as short-chip non‑ferrous metals in production and workshop environments DIN 1880 Type N geometry for standard arbors HSS‑Co5 alloy for higher heat resistance 8 flutes for consistent material removal Right‑hand cutting for conventional milling Reliable cutting performance for a broad range of steels The tool’s HSS‑Co5 composition provides increased hot hardness compared with standard high‑speed steel, enabling higher cutting temperatures and improved wear resistance under sustained loads. Combined with the DIN 1880 Type N profile, the cutter maintains concentric stability during interrupted and continuous cuts. With a 50 mm diameter, 8 flutes and an 8 mm cutting length, the design balances material removal rate and surface finish, while the 22 mm bore accommodates common arbor sizes for rapid changeovers and robust mounting. Improved chip control and repeatable surface quality Built with longitudinal and cross slots to DIN 138, the cutter promotes effective chip segmentation and evacuation, which is essential when working with short‑chip materials and alloys. This geometry reduces the risk of built-up edge and supports a consistent surface quality across batches. The right‑hand cutting configuration contributes to predictable force directions and tool engagement, aiding process planning and minimising secondary finishing work for components produced in series. Workshop-ready compatibility and longevity The Type N geometry and standard conformity facilitate interchangeability in existing toolholders and arbors, shortening setup times and supporting steady production throughput. The combination of robust material selection and deliberate flute count extends tool life and reduces downtime for replacement, delivering a pragmatic balance between performance and operating costs. For workshops seeking dependable milling media that integrate with conventional equipment, this cutter is a practical, production-oriented choice. For tailored technical advice, application recommendations or a fast quotation for the TECWERK cylindrical face mill (SKU 2000866622NW), contact Metav Werkzeuge – reliable supply and precision expertise from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 2000866622NW Norm: DIN 1880 Product type: Cylindrical face mill Manufacturer: TECWERK Facts Diameter: 50 mm Cutting length: 8 mm Number of flutes: 8 Bore diameter: 22 mm Special features Material: HSS‑Co5 Type N geometry Longitudinal and cross slots to DIN 138 Right‑hand cutting FAQ What materials is this cutter suitable for? The TECWERK cylindrical face mill is intended for milling structural, case‑hardened and quenched steels as well as short‑chip non‑ferrous metals, using the HSS‑Co5 specification for improved thermal resistance. What are the key dimensions of the tool? Diameter 50 mm, cutting length 8 mm and a bore diameter of 22 mm; the cutter conforms to DIN 1880 Type N specifications (SKU 2000866622NW). How many cutting edges does the cutter have? The tool features 8 flutes, arranged to provide stable material removal and uniform load distribution during milling. Does the cutter include specific chip‑control features? Yes, the design incorporates longitudinal and cross slots in accordance with DIN 138 to enhance chip control and reduce built‑up edge when machining short‑chip materials. Is this a right‑ or left‑hand cutting tool? This TECWERK face mill is a right‑hand cutting tool, suited to conventional milling directions. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust combination of HSS‑Co5 construction, TiCN coating and a 50 mm cutting diameter for dependable face and peripheral milling. Order TECWERK tooling through Metav Werkzeuge for consistent supply and expert procurement support. TECWERK cylindrical face cutter (DIN 1880), 50 mm, HSS‑Co5, TiCN, 8 teeth The TECWERK cylindrical face cutter (DIN 1880, 50 mm) is a Type N milling tool designed for precise face and peripheral milling of structural and heat‑treated steels as well as short‑chipping non‑ferrous metals. HSS‑Co5 core for heat and wear resistance TiCN coating for extended tool life 50 mm diameter, 8 cutting edges Longitudinal and transverse slot (DIN 138) Built for steady production performance and longer tool life The combination of a HSS‑Co5 substrate and a TiCN surface layer provides improved heat resistance and reduced flank wear compared with uncoated high‑speed steels. This results in a longer service interval and fewer tool changes during series production, supporting a more efficient machining cycle. With 8 cutting edges on a 50 mm diameter body, the cutter distributes cutting forces evenly to deliver a consistent surface finish and predictable tool behaviour under interrupted or heavy engagement. Secure mounting and reliable chip evacuation for clean milling A 22 mm bore allows compatibility with standard arbors and mounting systems, while the tool’s longitudinal and transverse slot according to DIN 138 aids chip formation and evacuation. These features reduce the risk of built‑up edge and prevent chip packing in deep cuts, which is especially beneficial when machining construction steels, case‑hardened components and quenched and tempered steels, as well as short‑chipping non‑ferrous materials. The right‑hand cutting geometry supports conventional milling setups and helps maintain process stability. Conformity to standards and clear application advantages Compliance with DIN 1880 (Type N) ensures interchangeability and straightforward replacement in standard milling setups across production lines. The tool’s cutting length 8 mm defines the effective axial engagement and is optimised for shallow face passes and fine finishing. Choosing a standardised tool simplifies inventory management and reduces downtime from ill‑fitting replacements, delivering tangible cost‑efficiency for workshops and production planners who prioritise predictable performance. Choose the TECWERK cylindrical face cutter for dependable milling results and contact Metav Werkzeuge for procurement and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000866630NW Standard: DIN 1880 Product label: Walzenstirnfräser DIN 1880 Typ N D.50mm HSS‑Co5 TiCN Z.8 TECWERK Dimensions & Core Data Diameter: 50 mm Cutting length: 8 mm Number of cutting edges: 8 Bore diameter: 22 mm Cutting direction: right‑hand Features & Applications Material: HSS‑Co (HSS‑Co5) Coating: TiCN (titanium carbonitride) Type: DIN 1880, Type N Slotting: longitudinal and transverse slot per DIN 138 Application: machining of construction steels, case‑hardened steels, quenched and tempered steels, short‑chipping non‑ferrous metals FAQ What materials is the TECWERK cylindrical face cutter suitable for? The TECWERK cylindrical face cutter (DIN 1880, SKU 2000866630NW) is specified for construction steels, case‑hardened steels, quenched and tempered steels and short‑chipping non‑ferrous metals. How does the TiCN coating benefit machining performance? The TiCN coating on this cutter reduces friction and flank wear, which extends tool life and improves surface finish under increased thermal loads. Which mounting interface is required for this cutter? The cutter accepts a 22 mm bore for mounting on standard arbors; confirm arbor compatibility with the machine tool spindle before installation. What does the DIN 1880 Type N designation mean for workshop use? DIN 1880 Type N indicates a standardised cylindrical face cutter geometry, simplifying replacements and ensuring consistent mounting and cutting behaviour across production tools. Can this cutter handle interrupted cuts or tough workpieces? The HSS‑Co5 substrate enhances toughness and thermal resistance, making the cutter suitable for interrupted engagement and demanding steels when used with appropriate machining parameters. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co5 substrate, TiCN coating and an efficient eight‑edge geometry for reliable throughput in small to medium milling operations; order directly via Metav Werkzeuge or consult our specialists for application advice. Walzenstirnfräser DIN 1880 Typ HR D.50mm HSS‑Co5 TiCN Z.8 TECWERK – high‑performance face mill with TiCN coating and 50 mm diameter The Walzenstirnfräser DIN 1880 Typ HR D.50mm HSS‑Co5 TiCN Z.8 TECWERK is a compact, right‑hand cutting face mill designed for milling construction, alloy and tempered steels as well as short‑chip non‑ferrous metals HSS‑Co5 substrate for improved toughness TiCN coating for extended tool life 50 mm diameter for compact setups 8 cutting edges, right‑hand cutting Consistent material performance and reduced tool wear The cutter’s HSS‑Co5 substrate combines high fracture resistance with good thermal stability, which supports continuous operation under moderate feed rates. The TiCN coating reduces adhesion and improves abrasion resistance, helping to maintain a sharp cutting edge over multiple passes. For production planners this translates into fewer tool changes and more predictable process windows. DIN 1880 compliant geometry ensures compatibility with standard toolholders and helps to maintain repeatable machining results. Optimised geometry for efficient chip control and finish With an 8‑edge configuration and a hinterschliffenes chord profile plus longitudinal and transverse grooves according to DIN 138, the tool promotes short, controllable chips when machining short‑chip non‑ferrous metals and a wide range of steels. The right‑hand cutting direction and the flute design reduce vibration and support a consistent surface quality on moulded or hardened workpiece surfaces. The result is a balance between material removal rate and surface finish that benefits repetitive milling tasks. Practical dimensions and mounting information The face mill features a 50 mm diameter and a bore diameter of 22 mm, suitable for standard arbor mounting in compact milling heads. The cutting length of 8 mm and a nominal width of 36 mm (data supplied) suit a variety of slotting and face milling operations in small to medium‑sized components. The combination of these dimensions with DIN 1880 geometry allows quick integration into existing setups without complex retooling, supporting short changeover times in batch production. Application focus: where this cutter performs best Engineered for machining construction, case‑hardened and tempered steels as well as short‑chip non‑ferrous metals, the tool is aimed at workshops and production lines that require a robust, general‑purpose face mill. The solid HSS‑Co design and TiCN surface treatment make it particularly suitable where intermittent cuts, variable material hardness, or higher toughness demands are present. Process engineers will appreciate the predictable wear progression and straightforward re‑conditioning strategy that this cutter offers. Contact Metav Werkzeuge for tailored cutting data and order coordination—call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for specific materials and machines Technical data Article number: 2000866670NW SKU: 2000866670NW Norm: DIN 1880 Product type: Face mill Manufacturer: TECWERK Facts Diameter: 50 mm Number of cutting edges: 8 Bore diameter: 22 mm Cutting length: 8 mm Width: 36 mm Special features Material: HSS‑Co Coating: TiCN Right‑hand cutting Type HR, hinterschliffenes chord profile Longitudinal and transverse grooves according to DIN 138 Packaging unit: 1 FAQ What materials is the Walzenstirnfräser DIN 1880 Typ HR D.50mm HSS‑Co5 TiCN Z.8 TECWERK suitable for? The Walzenstirnfräser DIN 1880 Typ HR D.50mm HSS‑Co5 TiCN Z.8 TECWERK is suitable for milling construction, alloy and tempered steels as well as short‑chip non‑ferrous metals, as specified by its DIN 1880 geometry and material recommendations. How does the TiCN coating influence tool life? The TiCN coating on the face mill reduces adhesive wear and improves abrasion resistance, which extends the effective service life of the HSS‑Co5 cutting edges under typical production conditions. What mounting interface is required for this face mill? The cutter requires an arbor or holder compatible with a 22 mm bore; the DIN 1880 standard geometry assists in ensuring proper seating and concentricity in standard toolholders. How many cutting edges does the tool have and what is the benefit? Equipped with 8 cutting edges, the tool offers efficient material removal and a balanced distribution of wear, which can reduce tooling costs per processed part when compared with lower‑edge configurations. Is this face mill suitable for intermittent or rough milling? Yes, the HSS‑Co substrate combined with the TiCN coating and the HR profile make the cutter robust enough for intermittent cuts and moderate roughing operations while still delivering acceptable surface quality. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the TiCN surface treatment and HSS‑Co5 substrate to extend tool life and maintain consistent surface quality during batch runs; the DIN 1880 design ensures straightforward integration into standard holders. Order the TECWERK tool directly via Metav Werkzeuge or contact our consultants for tailored advice. Cylindrical face mill DIN 1880 Type NR, 50 mm, HSS‑Co5, TiCN, 8 teeth — TECWERK Cylindrical face mill DIN 1880 Type NR is a compact face milling cutter engineered for precision machining of steels and short‑chipping non‑ferrous materials in production and workshop environments. HSS‑Co5 base for higher heat resistance TiCN coating for extended tool life 8 cutting teeth for a stable surface finish DIN 1880 compatibility for standardised clamping Consistent cutting performance through material and coating technology The combination of a HSS‑Co5 substrate and a TiCN surface layer delivers a balance of toughness and hardness that stabilises performance under elevated temperatures. The cobalt‑alloyed high‑speed steel increases red hardness and fracture resistance, while the titanium carbonitride layer reduces friction and improves wear resistance, resulting in longer intervals between regrinds and fewer tool changes in continuous production. Easy integration with standardised mounting and secure clamping Built to DIN 1880 dimensions, the tool accepts standard holders and simplifies tool change routines on milling heads designed for DIN 1880 cutters. The 22 mm bore and 50 mm diameter provide compact geometry for tight setups, while the incorporated axial and cross slots per DIN 138 aid chip flow and coolant access. These features reduce setup time and support reproducible clamping across batches. Broad material applicability and reliable surface finish With 8 teeth and right‑hand cutting, the cutter is optimised for steady chip formation and a uniform surface result when machining construction steels, case‑hardening and quenched‑and‑tempered grades, plus short‑chipping non‑ferrous metals. The tooth count and profile support reduced vibration at moderate feed rates, which benefits dimensional stability and lowers the risk of chatter in serial machining. Practical features that lower operating costs and simplify handling The relief‑ground tooth profile and cutting length 8 mm provide controlled engagement and predictable wear behaviour, improving tool life planning. Built‑in chip evacuation paths and a compact width 36 mm make the cutter suited to confined operation spaces without compromising removal rates. Clear specifications and standardised interfaces help to keep machine downtime to a minimum and ease inventory management. For application advice or to specify the TECWERK cylindrical face mill for a production task, contact Metav Werkzeuge for a technical consultation via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000866650NW Label: Cylindrical face mill DIN 1880 Type NR, 50 mm, HSS‑Co5, TiCN, 8 teeth SKU: 2000866650NW Packaging unit: 1 Facts Diameter: 50 mm Cutting length: 8 mm Bore diameter: 22 mm Teeth: 8 Width: 36 mm Special features Coating: TiCN Material: HSS‑Co5 Standard: DIN 1880 Type: NR Relief‑ground tooth profile Axial and cross slots per DIN 138 Right‑hand cutting Application: construction steels, case‑hardening and quenched‑and‑tempered steels, short‑chipping non‑ferrous metals FAQ What materials is this face mill suitable for? The TECWERK cylindrical face mill (Type NR, SKU 2000866650NW) is designed for machining construction steels, case‑hardening and quenched‑and‑tempered steels, as well as short‑chipping non‑ferrous metals. How does the TiCN coating benefit production runs? TiCN reduces friction and increases surface hardness; when applied to the HSS‑Co5 substrate of this cutter, it improves wear resistance and helps maintain cutting edge life across longer production cycles. Which standard holder interface is required for this cutter? This cutter conforms to DIN 1880 dimensions and fits holders and arbors designed for DIN 1880 cylindrical face mills; the 22 mm bore is a key datum for selecting the correct adaptor. What advantages do the axial and cross slots provide? The axial and cross slots (per DIN 138) promote effective chip evacuation and coolant access, which supports consistent cutting conditions and helps prevent built‑up edge formation. How many teeth does the cutter have and what effect does that have? With 8 teeth, the cutter offers stable engagement and a fine surface finish at appropriate feed rates, reducing vibration and improving dimensional consistency on serial work. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a high‑precision cutting solution that combines HSS‑Co5 toughness, DIN 1880 geometry and an optimised eight‑edge design for consistent removals in demanding steels and short‑chip non‑ferrous metals; order via Metav Werkzeuge or consult our specialists for matching tool holders and machining parameters. Cylindrical face mill DIN 1880, 63 mm — HSS‑Co5, 8 flutes (TECWERK) A cylindrical face mill engineered for robust face and slot milling of construction, case‑hardened and tempered steels as well as short‑chip non‑ferrous metals HSS‑Co5 for extended tool life DIN 1880 geometry for standardised fit 63 mm diameter with 8 cutting edges Precision and continuous productivity on the machine bed The combination of a 63 mm diameter and 8 flutes delivers a balanced cut with lower vibration, which translates into steady surface finish and repeatable cycle times. The cutter’s conformity to DIN 1880 ensures compatibility with standard tool holders and straightforward set‑up, reducing non‑productive time. Reliability in feed and speed selection is supported by the tool’s robust construction, enabling predictable machining windows for medium‑duty to heavy‑duty milling tasks. Tough substrate and application range for longer runs Manufactured from HSS‑Co (high‑speed steel with cobalt), the tool provides higher hot hardness and wear resistance compared with conventional high‑speed steels. This material choice extends edge life during interrupted cuts and in higher cutting temperatures, making the cutter suitable for construction steels, case‑hardened and tempered steels, and short‑chip non‑ferrous alloys. The intrinsic material benefits reduce the frequency of tool changes and support longer uninterrupted production runs. Chip control and geometry explained for secure surfaces The cutter features a ground cord profile and longitudinal and transverse grooves manufactured to DIN 138, combined with a right‑hand cutting direction to promote short, controlled chips. These geometric elements minimise built‑up edge and improve evacuation in through‑feed and side‑milling operations. For machinists unfamiliar with the term, the cord profile refers to a shaped cutting edge that optimises shear behaviour, while the grooves assist chip flow and coolant penetration for consistent surface quality. Practical integration and serviceability in the workshop Standard compliance and a 27 mm bore diameter enable fast mounting and compatibility with commonly used arbors and adaptors. The tool’s nominal features support straightforward tool management: inventory tracking is simplified by the standardised form, and tooling decisions are aided by measurable parameters such as diameter, flute count and material grade. Where process optimisation is required, pairing the cutter with correctly rated spindle speeds and feeds will yield the best balance between finish and tool life. Discuss tool mounting options and application specifics with Metav Werkzeuge to ensure the TECWERK face mill matches the intended machining task; contact via info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations Technical Data Article number: 2000866664NW Standard: DIN 1880 Product type: Face milling cutter Facts Diameter: 63 mm Cutting edges: 8 Cutting length: 8 mm Bore diameter: 27 mm Width: 40 mm Special features Material: HSS‑Co5 Type HR with ground cord profile Longitudinal and transverse grooves to DIN 138 Right‑hand cutting direction Suited for construction, case‑hardened and tempered steels and short‑chip non‑ferrous metals FAQ What materials is this cutter suitable for? The TECWERK cylindrical face mill is designed for construction steels, case‑hardened and tempered steels as well as short‑chip non‑ferrous metals, exploiting the HSS‑Co5 substrate for improved wear resistance. How many cutting edges does the tool have and why does it matter? The cutter has 8 cutting edges, which balances material removal rate and surface finish while reducing per‑edge load for prolonged life. Is the cutter compatible with standard tool holders? Yes, the geometry conforms to DIN 1880, and the 27 mm bore ensures compatibility with standard arbors and adaptors used in general shop practice. What are the chip control features built into the design? Ground cord profiling plus longitudinal and transverse grooves (to DIN 138) promote short, controlled chips and improved evacuation during face and side milling. Can the cutter handle interrupted cuts? Thanks to the cobalt‑alloyed HSS‑Co5 material and robust profile, the cutter performs reliably in interrupted and mixed‑cut conditions typical of structural and tempered steels. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust HSS‑Co5 cutting geometry and DIN 1880 Type N standardisation for steady material removal and predictable tool behaviour; order directly via Metav Werkzeuge or consult their specialists for technical clarification and supply. Cylindrical face mill DIN 1880 Type N D63 mm (HSS‑Co5) – TECWERK The Cylindrical face mill DIN 1880 Type N D63 mm is a high‑alloy milling cutter designed for face milling construction, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals in production and workshop environments HSS‑Co5 high‑alloy cutting material DIN 1880 Type N geometry Longitudinal and transverse coolant grooves 8 cutting teeth for smooth removal Suitable for steels and short‑chipping non‑ferrous metals Consistent cutting performance for industrial use The Cylindrical face mill DIN 1880 Type N D63 mm combines HSS‑Co5 tool steel with a classic Type N geometry to deliver reliable wear resistance and thermal stability in continuous use. The 63 mm diameter and 8 teeth are balanced to provide steady chip load distribution, which reduces vibration and extends tool life. With an 8 mm cutting length, the tool is suited to shallow face milling and peripheral passes where a consistent surface finish and low tool deflection matter. The standardised geometry supports reproducible machining results on mixed production runs. Secure mounting and efficient chip control A precise 27 mm bore ensures stable mounting in compatible adaptors and arbors, supporting concentricity and repeatability in assembly. The integrated longitudinal and transverse groove design, produced to DIN 138, enhances chip evacuation and coolant delivery at the cutting zone. Combined with right‑hand cutting, these features favour the evacuation of short, broken chips typical of construction, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals, reducing the risk of recutting and surface damage. Production benefits: standards, predictability and throughput Conformity to DIN 1880 provides interchangeability with established tool holders and machining set‑ups, simplifying tool procurement and changeover. The cutter’s geometry promotes predictable chip control and steady cutting forces, which supports higher process stability and fewer unexpected stoppages. For operations that value repeatability, the result is improved efficiency and a more consistent part finish across batches, reducing rework and downtime in both jobbing shops and series production. Practical use and sourcing for workshops The robust construction and clear specification make this cutter attractive for precision workshops and industrial users seeking a dependable face‑milling solution. The tool performs well in general face‑milling tasks where short chips are produced and where a tool conforming to established DIN standards is preferred. For procurement and technical clarification, Metav Werkzeuge offers detailed product information and advice, drawing on its extensive inventory and experience supplying workshop equipment to European customers For tailored advice on the TECWERK cylindrical face mill or to request a supply recommendation, contact Metav Werkzeuge in Emmerich for precise technical support and prompt handling of enquiries. Technical data Article number: 2000866624NW Name: Cylindrical face mill DIN 1880 Type N D63 mm (HSS‑Co5) Manufacturer: TECWERK Numbers / Core technical data Diameter: 63 mm Cutting length: 8 mm Number of cutting edges: 8 Bore diameter: 27 mm Packing unit: 1 Designs / Special features Material: HSS‑Co5 Standard: DIN 1880 Coolant grooves: Longitudinal and transverse groove to DIN 138 Cutting direction: Right‑hand cutting Application: Machining of construction, case‑hardened and tempered steels; short‑chipping non‑ferrous metals FAQ What materials is the cutter suitable for? The cutter is specified for machining construction, case‑hardened and tempered steels and short‑chipping non‑ferrous metals, matching the application information provided for this TECWERK face mill (SKU 2000866624NW). How many cutting edges does the tool have and what finish can be expected? This face milling cutter has 8 cutting teeth, which supports steady material removal and a consistent surface finish in face‑milling operations. Which standards does the tool conform to? The tool is manufactured to DIN 1880 with coolant grooves produced to DIN 138, ensuring compatibility with standard tool holders and predictable chip evacuation. What is the bore size for mounting the cutter? The cutter features a 27 mm bore, intended for secure mounting in compatible arbors and adaptors. Is the cutting direction left or right? The cutter is right‑hand cutting, designed for conventional milling set‑ups. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust combination of HSS‑Co5 construction, standardised DIN 1880 geometry and an Ø63 mm cutter body to secure consistent milling performance in small and medium series production; order the TECWERK tool directly via Metav Werkzeuge or consult the team for application advice. TECWERK Cylindrical Face Mill Ø63 mm (HSS‑Co5) — 8 teeth, DIN 1880 TECWERK Cylindrical Face Mill Ø63 mm (HSS‑Co5) — DIN 1880 Type NR is designed for high‑quality face milling of a variety of steels and short‑chipping non‑ferrous materials in workshop and light industrial settings HSS‑Co5 high‑cobalt cutting tool DIN 1880 standardised geometry Relief‑ground chord profile 8 cutting edges, right‑hand cut Durable alloy for predictable machining results Constructed from HSS‑Co5, this cutter offers elevated hot hardness and wear resistance compared with conventional high‑speed steels, which leads to more stable cutting under intermittent loads. The cobalt‑alloyed substrate improves resistance to tempering and allows the tool to tolerate higher cutting temperatures without rapid loss of hardness. For production environments this translates into predictable tool life and reduced unscheduled downtime, as the solid‑tool design avoids the variability of indexable inserts while maintaining a competitive service life. Standardised geometry for consistent surface quality The tool's compliance with DIN 1880 and the relief‑ground chord profile ensure reproducible cutting geometry across batches, simplifying tool selection and process setup. The cutter features 8 cutting edges and is manufactured with longitudinal and transverse grooves to DIN 138, which support chip control and stable engagement. These characteristics reduce vibration and help deliver a consistent surface finish; in practical terms fewer passes are required to reach dimensional and visual targets, improving throughput without complex parameter tuning. Versatile application across common workshop materials Engineered as a right‑hand cut face mill, the cutter is suitable for machining structural steels, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals, making it a flexible choice for mixed‑material job shops and maintenance departments. The tool’s geometry and alloy combination favour sectors where frequent material changes occur and where short, controlled chips are expected from copper alloys, aluminium alloys or similar materials. The result is dependable performance across a broad range of everyday metalworking tasks. Practical characteristics that speed up production planning With an Ø63 mm body, 8 mm cutting length, and a 27 mm bore, the cutter integrates into many machines with appropriate arboring, while the 40 mm width provides a balance between material removal rate and accessibility in confined setups. The standardised Type NR designation reduces uncertainty when specifying replacements or extensions of existing toolsets. For procurement and process engineers, these measurable data points enable rapid comparison, straightforward inventory management and clear documentation of capability for quality records. Discuss integration of the TECWERK face mill with Metav Werkzeuge—call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored recommendations and rapid supply from Emmerich. Technical Data Article number: 2000866644NW Product label: Cylindrical face mill DIN 1880 Type NR Ø63 mm HSS‑Co5 Z=8 TECWERK Manufacturer: TECWERK Facts Diameter: 63 mm Cutting length: 8 mm Bore diameter: 27 mm Number of cutting edges: 8 Width: 40 Special features Material: HSS‑Co5 Standard: DIN 1880 Type: NR Relief‑ground chord profile Longitudinal and transverse groove to DIN 138 Right‑hand cutting Application: structural steels; case‑hardened and tempered steels; short‑chipping non‑ferrous metals FAQ What materials is the TECWERK cylindrical face mill suited for? The TECWERK cylindrical face mill is suitable for structural steels, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals, offering versatile performance for mixed‑material shops. How many cutting edges does the cutter have and what is the cutting direction? The cutter features 8 cutting edges and is manufactured as a right‑hand cut, which affects chip flow and the preferred feed direction during milling operations. Which standards and profiles define the cutter geometry? The geometry is defined to DIN 1880, with a relief‑ground chord profile and longitudinal and transverse grooves to DIN 138 to support chip control and consistent cutting behaviour. What are the mounting and dimensional details to check before ordering? Key dimensions to confirm are the Ø63 mm body diameter, 8 mm cutting length, and 27 mm bore; these must be compatible with the machine arbor and fixture system in use. Is this cutter intended for high‑speed applications? Made from HSS‑Co5, the cutter provides improved hot hardness and is suited to moderately elevated cutting speeds typical for workshop and light production use rather than extreme high‑speed machining regimes. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of HSS‑Co5 robustness and the TiCN coating for extended tool life; the 63 mm diameter and 8 flutes deliver stable material removal in mixed steel and short‑chipping non‑ferrous applications. Order the cylindrical face mill directly via Metav Werkzeuge or consult our specialists for application advice. Cylindrical face mill DIN 1880 Type N — 63 mm, HSS‑Co5, TiCN — TECWERK A cylindrical face mill (Type N) designed for general workshop and industrial milling of construction, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals; complies with DIN 1880 and features longitudinal and transverse grooves per DIN 138. DIN 1880 Type N specification HSS‑Co5 substrate with TiCN coating 8 flutes for steady chip control 27 mm bore for standard arbors High material removal with predictable performance The cutter’s 63 mm diameter combined with 8 flutes provides a balanced cut profile that reduces vibration and delivers consistent axial engagement. The HSS‑Co5 substrate supplies the toughness required when facing intermittent cuts and varying surface hardnesses, while the TiCN coating improves wear resistance and reduces built‑up edge during short‑chip finishes. These properties translate directly into longer tool life and fewer tool changes, maintaining production flow and reducing unplanned downtime. Coating and substrate: extended service life and reliable finishes A TiCN coating on a cobalt‑enriched high‑speed steel body blends hardness and fracture resistance. The coating lowers friction and improves thermal stability at the cutting edge, which helps preserve geometry under sustained milling of structural and case‑hardened steels. When a fine surface and dimensional consistency are required, the coated tool sustains cutting performance over longer cycles, reducing the need for frequent regrinds or replacement. Designed for compatibility and secure mounting The cutter’s 27 mm bore and adherence to DIN 1880 make it compatible with standard arbors and toolholders used in many milling setups. The Type N geometry with longitudinal and transverse grooves according to DIN 138 facilitates reliable chip evacuation for short‑chipping materials and reduces the likelihood of clogging. This results in safer operation and fewer interruptions to the machining process when switching between steel grades and aluminium alloys. Application focus and machining advantages Engineered for the machining of construction, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals, the cutter offers a practical combination of toughness and surface integrity. The right‑hand cutting orientation and defined 8‑tooth arrangement enable efficient feed rates while maintaining control over chip formation. For production environments demanding repeatable results, the geometry supports consistent dimensional accuracy and a stable surface finish. Contact Metav Werkzeuge for tailored advice and swift supply from Emmerich — help with application selection and delivery is available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 2000866632NW Norm: DIN 1880 Brand: TECWERK Product type: Cylindrical face mill Core data Diameter: 63 mm Number of flutes: 8 Bore diameter: 27 mm Cutting length: 8 mm Special features Material: HSS‑Co5 Coating: TiCN Cutting direction: right‑hand cut Type: Type N with longitudinal and transverse groove per DIN 138 Application: milling of construction, case‑hardened and tempered steels; short‑chipping non‑ferrous metals Packaging unit: 1 FAQ Which materials is this cutter suited for? The cylindrical face mill (TECWERK, SKU 2000866632NW) is specified for machining construction steels, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals. What is the bore size and how is the cutter mounted? The cutter has a 27 mm bore designed for use with standard arbors compatible with DIN 1880 face mills; secure clamping to the arbor ensures concentric running. How does the TiCN coating benefit performance? The TiCN coating reduces friction and wear on the cutting edges of the HSS‑Co5 substrate, improving thermal stability and extending tool life under demanding milling conditions. Is the geometry suitable for chip control? Yes; the Type N geometry with longitudinal and transverse grooves to DIN 138 and 8 flutes promotes effective chip evacuation for short‑chipping materials. Does the tool comply with recognised standards? The cutter conforms to DIN 1880 and incorporates groove features according to DIN 138 for reliable industrial use. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

The combination of a TiCN hard coating and an HSS‑Co5 substrate delivers durable cutting performance and longer tool life, while the 63 mm, eight‑edge design provides stable chip control for mixed steel and short‑chipping non‑ferrous work. Order via Metav Werkzeuge or consult the team for application advice. Cylindrical face mill DIN 1880 Type NR, 63 mm — HSS‑Co5, TiCN, 8 teeth (TECWERK) A cylindrical face mill for robust face and peripheral milling in construction, case‑hardened and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals HSS‑Co5 substrate for heat resistance TiCN coating for extended tool life 63 mm diameter with 8 cutting edges Longitudinal and transverse groove per DIN 138 Proven high‑speed cutting for mixed materials This face milling cutter combines an HSS‑Co5 substrate with a TiCN surface finish to balance toughness and wear resistance. The cobalt‑enriched high‑speed steel provides improved hot hardness compared with standard HSS, which permits higher cutting performance under intermittent loads. The hard coating reduces adhesive wear and extends service intervals, resulting in fewer tool changes and more consistent component quality in serial work. Secure mounting and standardised compatibility for quick setup Designed to DIN 1880 Type NR, the cutter includes a 27 mm bore and both longitudinal and transverse grooves produced to DIN 138. These features ensure secure seating on standard arbors and reliable torque transmission during heavy cuts. The standardised interface simplifies tool inventory management and reduces machine downtime when swapping cutters, enabling predictable production planning in workshop and industrial environments. Stable chip control and reliable edge geometry With eight cutting edges and a right‑hand cutting orientation, the cutter is optimised for stable chip formation on short‑chipping materials. The tool’s relieved cutting profile improves chip breaking and reduces burr formation on finished surfaces, which is particularly advantageous when machining construction steels and short‑chipping non‑ferrous alloys. The eight‑tooth configuration balances material removal rate and surface finish for efficient milling cycles. Practical benefits for the production floor The combination of material choice, coating and geometry results in a cutter that supports higher feed rates and consistent surface quality, lowering overall machining costs through longer tool life and fewer reworks. Compatibility with common DIN‑standard toolholders and clear specification of bore and cutting dimensions simplifies procurement and spare‑part planning. For operations seeking repeatability and straightforward integration, this cutter offers a dependable solution. For technical advice or to confirm suitability for a specific machining task, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or by phone on +49 2822 7131930 — the team can provide application guidance and delivery options. Technical data Article number: 2000866652NW Name: Cylindrical face mill DIN 1880 Type NR, 63 mm, HSS‑Co5, TiCN, 8 teeth Manufacturer: TECWERK Standard: DIN 1880 Facts Diameter: 63 mm Cutting edges: 8 Cutting length: 8 mm Bore diameter: 27 mm Width: 40 mm Special features Material: HSS‑Co (HSS‑Co5) Coating: TiCN Right‑hand cutting Relieved cord profile Longitudinal and transverse groove per DIN 138 Suitable for construction, case‑hardened and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The cylindrical face mill is specified for milling construction steels, case‑hardened and quenched‑and‑tempered steels, and short‑chipping non‑ferrous metals; its HSS‑Co5 substrate and TiCN coating support these applications. How is the cutter mounted and secured? Mounting uses the 27 mm bore with longitudinal and transverse grooves to DIN 138; the DIN 1880 Type NR design ensures compatibility with standard arbors for secure seating. What advantages does the TiCN coating provide? The TiCN coating on this TECWERK face mill reduces adhesive wear and increases resistance to heat, resulting in longer tool life and more stable cutting performance. Which product reference should be quoted for ordering and enquiries? Please quote SKU 2000866652NW and the designation Cylindrical face mill DIN 1880 Type NR, 63 mm (TECWERK) when contacting sales or technical teams. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Precision and extended tool life are achieved through the combination of HSS‑Co5 substrate and TiCN coating together with the DIN 1880 Type HR geometry, delivering stable performance in demanding milling tasks. Order the cylindrical face mill directly via Metav Werkzeuge or consult the technical advisors for process-specific recommendations. Cylindrical face mill (DIN 1880 Type HR) — 63 mm, HSS‑Co5, TiCN, 8 flutes (TECWERK) The cylindrical face mill is engineered for robust face and slot milling of structural and heat-treated steels as well as short‑chip non‑ferrous metals in industrial workshop and production environments. HSS‑Co5 base material TiCN coating for enhanced wear resistance Standardised to DIN 1880 Type HR 63 mm diameter with 8 cutting edges Consistent edge life through material and coating Made from HSS‑Co5, the tool core provides high toughness and resistance against chipping under interrupted cuts, while the TiCN layer improves surface hardness and reduces adhesive wear. This combination extends service intervals and reduces downtime, meaning fewer tool changes and more predictable production cycles. The result is a cutter that balances wear resistance with edge stability for repeatable surface quality. Geometry that improves chip control and surface finish The Type HR geometry, executed to DIN 1880, includes a relief‑ground cord profile and longitudinal plus transverse grooves manufactured to DIN 138. These features promote reliable chip control and reduce re‑cutting of chips, which helps to maintain consistent surface finish and lower tool load. For operations requiring tight tolerances and a good face finish, the geometry reduces vibration and supports higher productivity without sacrificing quality. Application scope and material suitability This face mill is specified for milling construction steels, quenched and tempered steels and short‑chip non‑ferrous metals, making it suitable for general engineering, maintenance and series production tasks. The right combination of substrate and profile allows users to tackle both roughing and semi‑finishing passes where consistent chip breakage and predictable tool behaviour are required, particularly when working with short‑chip alloys common in assembly and component manufacture. Practical mounting and process advantages With a 63 mm diameter, 8 flutes and a 27 mm bore, the cutter offers a compact footprint and compatibility with common arbor configurations for secure mounting. The right‑hand cutting orientation supports conventional feed strategies on most milling machines and ensures stable cutting forces for improved tool life. Efficiency gains derive from fewer tool replacements and reliable repeatability when integrated into standard milling set‑ups. Contact Metav Werkzeuge today for procurement advice on the TECWERK cylindrical face mill and to discuss process optimisation — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 2000866672NW Standard: DIN 1880 Manufacturer: TECWERK Product type: Cylindrical face mill Label: Cylindrical face mill DIN 1880 Type HR, 63 mm, HSS‑Co5, TiCN, 8 flutes Facts Diameter: 63 mm Width: 40 mm Number of cutting edges: 8 Cutting length: 8 mm Bore diameter: 27 mm Pack unit: 1 Special features Coating: TiCN Material: HSS‑Co (cobalt‑alloyed high‑speed steel) Type HR geometry per DIN 1880 Relief‑ground cord profile Longitudinal and transverse grooves to DIN 138 Right‑hand cutting Suitable for construction, case‑hardened and quenched & tempered steels, and short‑chip non‑ferrous metals FAQ What materials is this face mill suitable for? The TECWERK cylindrical face mill is suitable for construction steels, case‑hardened and quenched & tempered steels, and short‑chip non‑ferrous metals as specified in the product data. How is the tool mounted to the arbor? The cutter has a 27 mm bore for standard arbor mounting; secure clamping and correct flange support are recommended to achieve the stated performance. Which standard does the cutter comply with? The tool conforms to DIN 1880 Type HR and incorporates grooves manufactured to DIN 138 for improved chip control. What benefits does the TiCN coating provide? The TiCN coating increases surface hardness and reduces adhesive wear, resulting in extended tool life and more consistent finishing behaviour under serial production conditions. How does the number of flutes affect cutting performance? With 8 flutes, the cutter balances feed capacity and surface finish, allowing fine step‑overs with even chip distribution for stable milling operations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Robust HSS‑Co5 construction with a TiCN coating and DIN 1880 conformity ensures stable milling performance and extended tool life; combine these qualities for efficient, repeatable results on steels and short‑chipping non‑ferrous metals. Order the cutter directly via Metav Werkzeuge or contact our consultants for tailored technical advice. TECWERK 80 mm face mill (Type HR, HSS‑Co5, TiCN coating, 10 teeth) The TECWERK 80 mm face mill is a compact Type HR milling cutter designed for medium stock removal and finishing work in steels and short‑chipping non‑ferrous metals. HSS‑Co5 substrate with TiCN coating 80 mm diameter for compact milling 10 teeth for efficient material removal Longitudinal and transverse slots (DIN 138) Engineered cutting performance for consistent production results The cutter is built on a HSS‑Co5 substrate and finished with a TiCN layer, which together provide a balance of toughness and wear resistance for demanding workshop use. Conformity to DIN 1880 and the Type HR designation indicate dimensional and profile standards that support predictable geometry in serial production; this reduces set‑up variance and supports process stability. The compact 80 mm diameter and the specified profile are aimed at achieving consistent surface finish while keeping tool overhang and vibration low, which is particularly advantageous in small to medium machining centres where rigidity is essential. Reliable chip control and stable clamping for uninterrupted shifts Designed with 10 teeth and a 27 mm bore, the cutter provides a stable connection to standard arbors while offering a high number of cutting edges for smooth material engagement. The combination of longitudinal and transverse slots (DIN 138) and a relieved profile aids chip formation and evacuation, reducing the risk of built‑up edge when machining short‑chipping alloys. The tool’s right‑hand cutting orientation and 10 mm cutting length support predictable toolpaths and make the cutter suitable for a range of face‑milling operations where controlled chip flow and tool life are priorities. Application versatility that lowers tooling overhead Suitable for the milling of construction, case and quenched steels as well as short‑chipping non‑ferrous metals, the cutter helps consolidate tooling requirements across mixed production runs. The 45 mm face width provides a useful balance between material removal rate and surface quality, so fewer tool changes are needed when switching tasks within compatible material families. For workshops seeking dependable, standards‑based tooling, this cutter reduces process interruptions and supports leaner inventory management through its broad applicability. For procurement or detailed specification support for the TECWERK 80 mm face mill, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to arrange supply and technical consultation. Technical data Article number: 2000866674NW Manufacturer: TECWERK Standard: DIN 1880 Product type: face mill Facts Diameter: 80 mm Face width: 45 mm Cutting length: 10 mm Number of teeth: 10 Bore diameter: 27 mm Special features Material: HSS‑Co5 Coating: TiCN (titanium carbonitride) Right‑hand cutting Type HR, relieved profile Longitudinal and transverse slots per DIN 138 For machining construction, case and quenched steels; short‑chipping non‑ferrous metals FAQ Is this cutter suitable for hardened steels? The TECWERK 80 mm face mill is intended for construction, case and quenched steels; for highly hardened materials beyond typical quenched ranges, tool selection should follow material hardness specifications and may require carbide tooling. What arbor or holder is required for mounting? Mounting requires a compatible arbor or holder that accepts a 27 mm bore; the cutter’s 27 mm bore ensures secure clamping in standard arbors designed for this diameter. How does the TiCN coating benefit machining? The TiCN coating on the TECWERK 80 mm face mill increases surface hardness and wear resistance, reducing flank wear and contributing to longer tool life in many steel and non‑ferrous applications. Can the cutter be used for finishing passes? Yes, the cutter’s relieved profile and the balance of cutting edges make it suitable for finishing and medium stock removal, delivering consistent surface quality when properly set up. Is this tool compliant with recognised standards? The tool is manufactured to DIN 1880 and the Type HR designation, offering standardised geometry and tolerances for industrial machining applications. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Reliable performance with a focus on durability and standard compliance: HSS‑Co5 construction, DIN 1880 Type N geometry and an 80 mm diameter deliver steady material removal and consistent surface quality. Combined with a 27 mm arbour bore and 10 cutting teeth, the cutter supports predictable feeds and stable run-out. Order this TECWERK face milling cutter via Metav Werkzeuge or consult Metav's specialists for application advice. Face milling cutter DIN 1880 Type N, Ø80 mm – HSS‑Co5, 10 teeth (TECWERK) A robust DIN‑compliant face milling cutter designed for machining structural and tempered steels as well as short‑chipping non‑ferrous metals. HSS‑Co5 high‑speed steel for durability DIN 1880 Type N geometry for stable milling 80 mm diameter with 10 cutting teeth 27 mm arbour bore, longitudinal and transverse groove Precision and tool life for consistent milling Constructed from HSS‑Co5, this cylindrical face mill combines the toughness of high‑speed steel with cobalt alloying to increase hot hardness and wear resistance. The DIN 1880 Type N profile ensures a secure seating on standard arbors and reduces vibration during passes, which translates into improved surface finish and extended tool life. With an 80 mm diameter and 10 teeth, the cutter balances material removal rate and chip evacuation for stable feeds on both manual and CNC milling equipment. The result is reproducible machining quality and fewer tool changes over production runs. Material range and effective chip control The tool is intended for milling structural steels, case‑hardened and tempered steels, and short‑chipping non‑ferrous metals, with the right‑hand cutting direction optimised for conventional milling strategies. The inclusion of longitudinal and transverse grooves in accordance with DIN 138 improves chip breaking and evacuation, particularly in short‑chip materials, while the 27 mm arbour bore provides compatibility with common mounting systems. The TECWERK face milling cutter offers a reliable compromise between aggressive cutting and controlled chip formation, making it suited to workshops that require flexible handling of diverse workpiece alloys. Integration into the workshop and operational benefits With a 45 mm effective width and a 10 mm cutting length, the cutter is compact yet capable of targeted face or slot milling operations where access and rigidity matter. The Type N geometry reduces cutting forces at the entry, lowering the risk of chatter and enabling cleaner edges, which shortens downstream finishing. For procurement and supply reliability, Metav Werkzeuge acts as a quality filter for the European market and can advise on matching holders and feeds to specific machines. Technical consultation is available for machining parameters and mounting recommendations to ensure optimal results and lifespan. Select the TECWERK HSS‑Co5 face milling cutter for reliable, DIN‑compliant performance and contact Metav Werkzeuge for tailored technical advice and supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866626NW Manufacturer: TECWERK Product type: Face milling cutter (Walzenstirnfräser) Facts Diameter: 80 mm Arbour bore: 27 mm Number of cutting teeth: 10 Width: 45 mm Cutting length: 10 mm Cutting direction: right‑hand cutting Standard: DIN 1880 Special features Material: HSS‑Co5 (cobalt‑alloyed high‑speed steel) Type N geometry Longitudinal and transverse groove per DIN 138 For structural, case‑hardened and tempered steels For short‑chipping non‑ferrous metals FAQ What materials can this face milling cutter machine effectively? The TECWERK face milling cutter is suitable for structural, case‑hardened and tempered steels, and for short‑chipping non‑ferrous metals, as specified for its Type N application. What are the mounting requirements for the cutter? Mounting uses a 27 mm arbour bore; the cutter conforms to DIN guidelines for seating and is intended for standard arbour holders compatible with DIN 1880 tooling. How many cutting teeth does the tool have and why does that matter? The cutter features 10 cutting teeth, which provides a balance between material removal rate and smooth chip flow, reducing load per tooth and improving surface finish. Is the geometry suitable for avoiding chatter on less rigid setups? The Type N geometry reduces entry forces and, together with the DIN‑compatible seating, helps to lower vibration risks on less rigid machines when appropriate feeds and speeds are used. Can the cutter be used on CNC machines as well as manual mills? Yes, the cutter's design and HSS‑Co5 material make it adaptable to both CNC and manual milling operations, provided the machine offers adequate rigidity and correct arbour mounting. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of durable HSS‑Co5 construction, DIN 1880 standardisation and a 10‑tooth geometry for consistent face milling across a range of steels and short‑chipping non‑ferrous metals. Order the cutter directly via Metav Werkzeuge or ask the consultants for application advice. Cylindrical face milling cutter (Type NR, Ø80 mm) — HSS‑Co5, 10 teeth, right‑hand The Cylindrical face milling cutter Type NR (Ø80 mm) by TECWERK is designed for robust, standardised face milling of structural and tempered steels as well as short‑chipping non‑ferrous metals. HSS‑Co5 construction for long tool life Standardised DIN 1880 mounting Longitudinal and transverse grooves DIN 138 Right‑hand cutting with 10 teeth Reliable material performance for demanding components The HSS‑Co5 substrate offers a balanced combination of toughness and red hardness, making the cutter suitable for milling construction steel, case‑hardened and quenched‑and‑tempered steels and short‑chipping non‑ferrous materials. This composition reduces the risk of chipping under intermittent cuts and helps maintain a constant cutting geometry during extended runs. The choice of a cobalt‑alloy high‑speed steel is particularly advantageous where impact resistance and thermal stability are required, providing predictable tool life in mixed‑batch production. Precision geometry that improves productivity Compliant with DIN 1880 and built as Type NR, the cutter features a compact Ø80 mm body with a 10‑tooth cutting arrangement and right‑hand cutting orientation for conventional spindle rotation. The body incorporates longitudinal and transverse grooves to DIN 138, which aid in secure seating and torque transmission in compatible toolholders. A relieved cutting‑edge profile enhances chip formation and evacuation, reducing heat build‑up and supporting higher removal rates without sacrificing surface quality. The combination of these geometrical details leads to shorter cycle times and a stable cutting process. Workshop integration, maintenance and handling advantages The tool’s bore diameter of 27 mm and its specified mounting standard simplify integration into existing setups that accept DIN‑compliant face mills. A cutting length of 10 mm and an effective width derived from the body dimensions allow predictable engagement and easy programming of machining passes. Because the cutter is manufactured to recognised standards, reconditioning and regrinding can be planned in line with common workshop workflows, helping to extend service life while retaining dimensional accuracy. Availability through Metav Werkzeuge ensures a reliable supply chain and straightforward ordering from a partner experienced in precision tooling. Contact Metav Werkzeuge for tailored application guidance and secure supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000866646NW Norm: DIN 1880 Type: NR Diameter: 80 mm Facts Cutting edges: 10 Cutting length: 10 mm Bore diameter: 27 mm Width: 45 mm Special features Material: HSS‑Co5 Relieved cutting‑edge profile Longitudinal and transverse grooves to DIN 138 Right‑hand cutting Suitable for construction, case‑hardened and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The TECWERK cylindrical face milling cutter is specified for construction steel, case‑hardened and quenched‑and‑tempered steels, and short‑chipping non‑ferrous metals according to the product description. Which standard does the cutter comply with? The tool is manufactured to DIN 1880 (Type NR) and includes longitudinal and transverse grooves according to DIN 138 for standardised mounting. How many cutting edges does the cutter have and what is the rotation direction? The cutter has 10 cutting edges and is designed for right‑hand cutting (conventional rotation). What are the key dimensions for toolholder compatibility? Key dimensions are Ø80 mm body diameter and a 27 mm bore, which suit holders and adaptors compatible with DIN 1880 specifications. Can the cutter be reconditioned or reground? The tool’s HSS‑Co5 substrate and standardised geometry support conventional reconditioning and regrinding practices in a workshop environment. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co5 material, DIN 1880 Type HR geometry and a compact Ø 80 mm diameter for efficient, reproducible face milling. Order the cutter directly via Metav Werkzeuge or consult our experts for application-specific recommendations. Cylindrical face mill DIN 1880 Type HR Ø 80 mm (HSS‑Co5) – TECWERK The Cylindrical face mill DIN 1880 Type HR Ø 80 mm (HSS‑Co5) is a robust cutting tool engineered for heavy‑duty milling of structural and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals in workshop and production environments HSS‑Co5 high‑cobalt tool steel DIN 1880, Type HR geometry Ø 80 mm with 10 cutting edges Longitudinal and transverse grooves DIN 138 Consistent metal removal through high‑performance tool steel Made from HSS‑Co5, the cutter offers enhanced hot hardness and wear resistance compared with conventional high‑speed steels, which translates into longer tool life and fewer interruptions during series production. The combination of the ten cutting edges and the tool's geometry enables steadier material removal rates; this reduces the number of tool changes and increases machine uptime. For production planners and workshop managers, that means more predictable cycle times and lower process costs per component. Stable machining thanks to DIN‑compliant geometry and chip control The DIN 1880 Type HR profile, together with the relieved chordal profile and the integrated longitudinal and transverse grooves (DIN 138), ensures reliable chip formation and evacuation. A clean chip flow prevents build‑up on the cutting edges and reduces the risk of vibration‑related marks on the workpiece. The tool's bore of Ø 27 mm gives a secure connection to standard arbors, supporting repeatable concentricity and minimising run‑out during face milling operations. Application range and practical process advantages Designed as a right‑hand cutting tool with a cutting length of 10 mm, this mill is suitable for machining structural steels, case‑hardened and quenched‑and‑tempered steels, as well as short‑chipping non‑ferrous metals. The tool's versatility makes it useful for job shops and maintenance departments that process mixed batches of ferrous and non‑ferrous components. For those unfamiliar with the terminology: “short‑chipping” metals create small, easily evacuable chips, improving surface finish and reducing the likelihood of chip entanglement in multi‑pass milling. Contact Metav Werkzeuge for tailored advice and to secure supply from Emmerich – telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: 2000866666NW Label: Walzenstirnfräser DIN 1880 Typ HR D.80mm HSS-Co5 Z.10 TECWERK Manufacturer: TECWERK Standard: DIN 1880 Core data Diameter: Ø 80 mm Cutting length: 10 mm Number of cutting edges: 10 Bore diameter: 27 mm Width: 45 mm Special features Material: HSS‑Co5 Type: HR geometry Relieved chordal profile Longitudinal and transverse grooves to DIN 138 Right‑hand cutting Suited for structural, case‑hardened and quenched‑and‑tempered steels Suited for short‑chipping non‑ferrous metals FAQ What materials can this face mill machine effectively? The TECWERK cylindrical face mill is suitable for structural steels, case‑hardened and quenched‑and‑tempered steels, and short‑chipping non‑ferrous metals, as specified in the product details. How does the HSS‑Co5 composition benefit machining? The HSS‑Co5 composition increases hot hardness and wear resistance compared with standard high‑speed steel, extending tool life and maintaining cutting performance under elevated temperatures. What does the DIN 1880 Type HR designation mean for workshop use? The DIN 1880 Type HR designation denotes a standardised cutter geometry optimised for face milling; it provides predictable chip behaviour and compatibility with DIN‑compliant toolholding systems. Is chip evacuation improved with this design? Yes, the relieved chordal profile and the longitudinal and transverse grooves (DIN 138) promote effective chip control, reducing build‑up and the risk of chatter during milling. Which arbor or bore size is required to mount the cutter? The cutter is supplied with a bore of Ø 27 mm, compatible with corresponding arbors for secure mounting and repeatable concentricity. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of a wear-resistant TiCN coating, an HSS‑Co5 substrate and the DIN 1880 Type NR profile for consistent chip control and extended tool life; order TECWERK cutters through Metav Werkzeuge or consult our specialists for precise application advice. Cylindrical face mill DIN 1880 Type NR, 80 mm, HSS‑Co5, TiCN, 10 teeth (TECWERK) A Cylindrical face mill DIN 1880 Type NR 80 mm designed for efficient milling of construction, case-hardened and quenched-and-tempered steels as well as short‑chipping non‑ferrous metals in industrial production environments HSS‑Co5 substrate with TiCN coating DIN 1880 Type NR geometry 80 mm diameter, 10 cutting edges Longitudinal and transverse coolant gullets High-performance substrate and coating for longer service intervals The HSS‑Co5 base material combined with a TiCN surface layer offers a balanced mix of toughness and thermal resistance, ideal for varied workshop demands. This composition reduces flank wear and improves resistance to adhesive wear during interrupted or continuous cuts, supporting longer uninterrupted runs. The cutter’s DIN 1880 profile ensures compatibility with standard toolholders and predictable cutting behaviour, which translates into fewer tool changes and improved process stability for serial production. The 80 mm diameter provides a stable cutting envelope while the 10 cutting edges allow for distributed engagement and predictable chip loads. Reliable chip control and improved surface quality A relief-ground chordal profile together with longitudinal and transverse coolant grooves to DIN 138 enhances chip formation and evacuation, minimising re-cutting and the risk of built-up edge. This geometry supports consistent surface finish on a variety of materials, especially on short‑chipping non‑ferrous metals and structural steels. The cutter’s right‑hand cutting direction and the specific flute arrangement reduce vibration and promote steady cutting forces, which helps to protect the workpiece geometry and achieve repeatable dimensional results. The integrated features focus on delivering measurable improvements in cycle reliability and final part quality. Practical mounting and workshop integration for efficient use The cutter is supplied with a 27 mm bore, making mounting straightforward on compatible arbors and ensuring concentricity for demanding machining tasks. The combination of HSS‑Co5 and a hard TiCN layer keeps maintenance predictable and supports a clear reconditioning strategy at the end of tool life. For production planners and workshop managers, the tool delivers a balance between durability and cost‑efficiency: less frequent replacements reduce downtime and consolidate tooling assortments. For specific clamping or arbor compatibility queries, technical assistance is available to ensure seamless integration into existing machining setups. Contact Metav Werkzeuge for tailored recommendations on matching TECWERK cylindrical face mills to specific materials and setups, and to arrange fast, reliable supply from our Emmerich site. Technical data Article number: 2000866654NW Label: Walzenstirnfräser DIN 1880 Typ NR D.80mm HSS‑Co5 TiCN Z.10 TECWERK Manufacturer: TECWERK Facts Diameter: 80 mm Cutting edges: 10 Cutting length: 10 mm Bore diameter: 27 mm Width: 45 Special features Material: HSS‑Co5 Coating: TiCN Geometry: DIN 1880 Type NR Relief‑ground chordal profile Longitudinal and transverse coolant grooves to DIN 138 Right‑hand cutting Suitable for construction, case‑hardened and quenched‑and‑tempered steels Suitable for short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The cylindrical face mill is specified for milling construction steels, case‑hardened and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals, as stated in the product data for the TECWERK Walzenstirnfräser (SKU 2000866654NW). How does the TiCN coating benefit workshop operations? The TiCN coating on this TECWERK cutter increases surface hardness and reduces adhesive wear, which helps to extend effective tool life and maintain consistent cutting performance under production conditions. What mounting interface is required for this cutter? The cutter uses a 27 mm bore, allowing secure mounting on compatible arbors; the specified bore diameter is included in the product data for the TECWERK cylindrical face mill (2000866654NW). How many cutting edges does the tool have and what advantage does that offer? Equipped with 10 cutting edges, the tool distributes cutting forces across multiple teeth, improving stability, reducing individual tooth load and supporting steady chip formation for reliable surface quality. Is the geometry standardised for easy replacement in existing setups? Yes, the cutter follows DIN 1880 Type NR geometry and uses established flute features to facilitate replacement and predictable cutting behaviour in standard tool systems. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Combining the HSS‑Co5 substrate with a TiCN coating and a 10‑tooth geometry delivers durable, high‑feed cutting performance and extended tool life for steel and short‑chipping non‑ferrous metals. Order the TECWERK face mill directly via Metav Werkzeuge or consult the specialist team for application matching. TECWERK Face Mill (DIN 1880) D 80 mm — HSS‑Co5, TiCN, Z=10 The TECWERK face mill is a DIN 1880 Type N cutter designed for robust face milling of construction, alloy and tempered steels and short‑chipping non‑ferrous metals in industrial and trade workshops. HSS‑Co5 substrate for improved heat resistance TiCN coating for longer tool life 10 cutting edges for high material removal DIN 1880 Type N with longitudinal and cross flute High‑temperature wear resistance for consistent production Built on a HSS‑Co5 substrate and finished with a TiCN coating, the cutter combines heat resistance with reduced friction to prolong service intervals. The chemical vapour‑deposited coating limits abrasion and helps prevent built‑up edge when machining medium to high alloy steels. Conformance to DIN 1880 Type N and the inclusion of longitudinal and cross flutes per DIN 138 provide a predictable chip flow, which supports stable tool life and repeatable component quality. Geometry and cutting data that boost throughput With an 80 mm diameter, 10 mm cutting length and 10 cutting edges, the tool geometry is optimised for high material‑removal rates while maintaining surface integrity. The right‑hand cutting orientation suits conventional milling setups and the 27 mm bore allows secure mounting in standard tool holders. The multi‑edge layout reduces load per tooth, enabling higher feed rates and improved cycle times without compromising accuracy. Practical advantages for workshop integration The cutter’s combination of substrate and coating reduces frequency of tool changes and helps maintain spindle uptime, which is particularly important in batch production and subcontract machining. The face mill’s construction supports machining of construction steels, case‑hardened and quenched‑and‑tempered grades as well as short‑chipping non‑ferrous metals, making it a versatile choice for mixed‑material production lines. Clear designation under established standards streamlines tool selection and inventory management. Decision support for purchasing and process planning Choosing a tool that matches workpiece material and machine capability is central to consistent throughput. The TECWERK face mill offers a balance of durability and performance that favours longer tool life and predictable results in series production. For planners and buyers, the standardised specification and robust design simplify qualification across multiple machines and reduce the need for frequent tool changes, contributing to overall process economy. Contact Metav Werkzeuge for tailored advice on selecting TECWERK face mills and to ensure the DIN 1880 Type N solution matches specific production requirements Technical data Article number (SKU): 2000866634NW Manufacturer: TECWERK Product: Face mill (Type N) Standard: DIN 1880 Facts Diameter: 80 mm Cutting length: 10 mm Number of teeth: 10 Bore diameter: 27 mm Width: 45 mm Pack unit: 1 Special features HSS‑Co5 material TiCN coating Right‑hand cutting DIN 1880 Type N designation Longitudinal and cross flute per DIN 138 Suitable for construction, tool and tempered steels and short‑chipping non‑ferrous metals FAQ What materials is this cutter designed to machine? The TECWERK face mill is specified for milling construction, tool and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals, reflecting the HSS‑Co5 substrate and TiCN coating performance. What does the TiCN coating provide? TiCN reduces abrasive wear and friction on the cutting edges, extending service life and helping to maintain consistent cutting performance under higher temperatures. How does the 10‑tooth geometry affect machining? A ten‑tooth arrangement spreads the cutting load, enabling higher feed per tooth, improved material removal rates and reduced vibration compared with fewer‑tooth configurations. Is the tool compatible with standard holders? The cutter’s 27 mm bore is intended for secure mounting in holders designed for DIN 1880 face mills; correct holder selection is recommended to ensure runout and stability. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund