63mm Face Milling Cutter HSS-Co5 TiCN 8 Teeth Right-Hand DIN 1880 - TECWERK

Take advantage of the combination of durable HSS‑Co5 construction and TiCN surface protection for consistent machining performance and reduced tool changes; order the TECWERK face mill directly via Metav Werkzeuge or consult our specialists for application advice.

Face mill DIN 1880 Type NR, 63 mm, HSS‑Co5, TiCN – TECWERK

A face mill DIN 1880 Type NR engineered for efficient machining of construction, case‑hardening and tempered steels, as well as short‑chipping non‑ferrous materials

• HSS‑Co5 construction for high toughness
• TiCN coating for increased tool life
• DIN 1880 Type NR standard compliance
• 63 mm diameter with 8 cutting edges

High productivity through proven cutting geometry and material choice

The TECWERK face mill DIN 1880 Type NR combines a HSS‑Co5 substrate with a TiCN coating to deliver a balance of toughness and wear resistance that suits interrupted and continuous milling. The cobalt‑alloyed high‑speed steel provides higher red‑hardness and improved fracture resistance compared with conventional HSS, while the TiCN layer reduces adhesive wear and delays the onset of built‑up edge. Together these characteristics support stable cutting at higher feed rates and extend the tool life, which contributes directly to increased machine uptime and lower tooling costs.

Reliable chip control and surface quality for mixed production

The cutter’s undercut chordal profile and the longitudinal and transverse grooves according to DIN 138 optimise chip formation and evacuation, reducing the risk of recutting and improving surface finish. With 8 cutting edges, the geometry promotes even load distribution across teeth, which stabilises cutting forces and helps achieve consistent surface integrity on materials such as construction steels, case‑hardened and quenched‑and‑tempered steels, and short‑chipping non‑ferrous metals. The right‑hand cutting direction supports common machining set‑ups and straightforward toolpath programming.

Practical mounting and process integration for workshop use

A bore diameter of 27 mm and a 63 mm overall diameter make the cutter compatible with a variety of standard arbors and holders, enabling straightforward integration into existing tool systems. The cutting length of 8 mm provides a defined axial engagement suitable for shallow face cuts and shoulder operations where controlled material removal is required. These measurable parameters assist process engineers in selecting appropriate spindle speeds and feeds, helping to keep cycle times predictable and reproducible across production runs.

Economical operation and maintenance benefits

The combination of a cobalt‑enriched high‑speed substrate and a hard TiCN coating reduces the frequency of tool changes and the likelihood of premature failures, supporting a cost‑effective tooling strategy for small and medium‑batch production. The standardised DIN 1880 Type NR form factor simplifies stock management and replacement planning within a workshop or supply chain. For businesses seeking dependable cutters without complex handling, this design offers a straightforward path to improved throughput and lowered per‑part tooling cost.

For guidance on selecting the right TECWERK face mill for a specific application, or to place an order through Metav Werkzeuge, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930

Technical data

• Article number: 2000866652NW
• Manufacturer: TECWERK
• Standard: DIN 1880

Facts

• Diameter: 63 mm
• Width: 40 mm
• Number of cutting edges: 8
• Cutting length: 8 mm
• Bore diameter: 27 mm

Special features

• Material: HSS‑Co (HSS‑Co5)
• Coating: TiCN
• DIN 1880 Type NR form
• Undercut chordal profile
• Longitudinal and transverse grooves per DIN 138
• Right‑hand cutting
• Suitable for machining construction steels, case‑hardening and quenched‑and‑tempered steels, and short‑chipping non‑ferrous metals

FAQ

What materials is this face mill suitable for?
The TECWERK face mill (DIN 1880 Type NR, SKU 2000866652NW) is intended for machining construction steels, case‑hardening and quenched‑and‑tempered steels, plus short‑chipping non‑ferrous materials.

How many cutting edges does the cutter have and what is the diameter?
This face mill has 8 cutting edges and a 63 mm diameter, providing balanced load distribution and a stable cutting action.

What are the advantages of the TiCN coating?
The TiCN coating on the TECWERK face mill increases surface hardness, reduces adhesive wear and helps prevent built‑up edge, which extends tool life and maintains surface finish.

Is the cutter right‑hand or left‑hand?
The cutter is right‑hand cutting, matching standard machining set‑ups and toolpath strategies.

Which bore size is required for mounting?
The tool features a 27 mm bore diameter, suitable for common arbor interfaces and holders used with DIN 1880 Type NR cutters.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund