63mm Face Milling Cutter HSS-Co5 TiCN 8 Teeth Right-Hand DIN 1880 - TECWERK

Benefit from the combination of TiCN wear resistance, a tough HSS‑Co5 substrate and an eight‑edge geometry for steady chip control and longer tool life; order the cutter directly via Metav Werkzeuge or consult our specialists for material‑specific recommendations.

Cylindrical face milling cutter DIN 1880, Type HR, D63 mm — HSS‑Co5 with TiCN coating, 8 cutting edges, TECWERK

The cylindrical face milling cutter DIN 1880, Type HR, D63 mm is built for high‑performance face milling of structural, case‑hardened and quenched/tempered steels as well as short‑chipping non‑ferrous metals in industrial and job‑shop environments.

• HSS‑Co5 substrate for increased heat resistance
• TiCN coating for extended tool life
• Eight‑cutting‑edge geometry for smooth cutting
• Longitudinal and transverse grooves to DIN 138

Optimised cutting performance for demanding materials

The cutter combines a high‑cobalt high‑speed steel substrate (HSS‑Co5) with a TiCN coating, providing a balance of toughness and surface hardness that helps resist thermal softening under interrupted cutting. This results in consistent cutting forces during face milling operations and extends tool intervals. The eight cutting edges reduce load per tooth, which lowers vibration and produces a more even surface finish on workpieces such as construction steels and short‑chipping non‑ferrous alloys. The technical setup targets productivity: fewer tool changes and reliable cycle times on serial milling tasks.

Durable design and protective coating for longer service life

A cobalt‑enriched high‑speed steel core gives the tool intrinsic resistance to bending and wear, while the TiCN coating adds a hard, low‑friction surface that discourages built‑up edge and abrasion. Together, these features reduce flank wear and preserve cutter geometry for extended periods. The right‑hand cutting direction and the relieved profile around the cutting edges ensure predictable chip formation and clearance. For workshop managers seeking low‑downtime tooling, this configuration supports stable life‑cycle costs and repeatable part quality under typical workshop feeds and speeds.

Precision geometry and standards compliance for consistent results

The cutter is manufactured to DIN 1880 and incorporates longitudinal and transverse grooves to DIN 138, which aid chip evacuation and seating on the arbor. The relief‑ground cord profile on the cutting edges improves entry behaviour and helps maintain dimensional accuracy during face cuts. Compliance with recognised standards simplifies process documentation and tool selection for quality‑assured production environments. Where tighter tolerances are required, the defined geometry reduces the need for secondary finishing passes.

Recommended applications and machining notes

Intended for face milling of construction steels, case‑hardened and tempered steels and short‑chipping non‑ferrous metals, the tool performs best with moderate axial depth and steady feed per tooth to maintain chip form. The combination of HSS‑Co5 and TiCN suits intermittent cutting and mixed production runs where robustness matters more than the highest carbide cutting speeds. When machining tougher steels, use appropriate coolant and monitor cutting parameters to balance tool life and productivity. For non‑ferrous materials, the coating helps to reduce adhesion and keep tolerances stable.

For material‑specific advice or to discuss supply from Metav Werkzeuge – including suitability for particular steels or alloys – contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to arrange a consultation or order.

Technical data

• Article number / SKU: 2000866672NW
• Manufacturer: TECWERK
• Product type: Cylindrical face milling cutter
• Standard: DIN 1880

Specifications

• Diameter: 63 mm
• Width: 40 mm
• Cutting length: 8 mm
• Bore diameter: 27 mm
• Number of cutting edges: 8
• Packaging unit: 1

Special features

• Material: HSS‑Co (HSS‑Co5)
• Coating: TiCN
• Cutting direction: Right‑hand cut
• Type: HR
• Relief‑ground cord profile
• Longitudinal and transverse grooves per DIN 138
• Suited for construction steel, case‑hardened and quenched‑tempered steels, short‑chipping non‑ferrous metals

FAQ

What materials is this cutter suitable for?
The cylindrical face milling cutter (Type HR, D63 mm) is suitable for construction steels, case‑hardened and quenched/tempered steels and short‑chipping non‑ferrous metals, as specified in the technical features.

How does the TiCN coating benefit machining?
The TiCN coating increases surface hardness and reduces friction; on the TECWERK cutter this helps lower built‑up edge and extend cutting intervals under typical face‑milling conditions.

How many cutting edges does the tool have and what is the effect?
The tool features 8 cutting edges, which distribute cutting forces across more teeth, improving chip control and smoothing surface finish during face milling.

Is the cutter compatible with standard DIN 1880 arbors?
The tool is manufactured to DIN 1880 and includes grooves to DIN 138, facilitating correct mounting and chip evacuation on compatible arbors.

Can the cutter be used for interrupted cutting?
Yes; the HSS‑Co5 substrate combined with TiCN coating delivers toughness and wear resistance that make the cutter suitable for interrupted face‑milling operations.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund