10mm Solid Carbide Long Helix End Mill TiAlN Coating 35–38° Spiral, 6 Flutes, DIN 6527 - TECWERK

Take advantage of a long, vibration‑reduced carbide cutter with a TiAlN surface for extended tool life and consistent finishes; its 6‑flute geometry and 35–38° helix deliver high material removal rates while maintaining dimensional accuracy. Order directly via Metav Werkzeuge or consult the technical team for application guidance.

TECWERK Solid Carbide Long End Mill D10 mm — TiAlN, 6 flutes

The TECWERK Solid Carbide End Mill D10 mm is a long, TiAlN‑coated, six‑flute cutter designed for vibration‑reduced roughing and finishing across steels, cast materials and non‑ferrous alloys

• Solid carbide construction with TiAlN coating
• Six flutes with 35–38° helix for high feed rates
• Cylindrical shank to DIN 6535 HB, tolerance h6
• Long design with neck relief for low vibration

High throughput and longer tool life for series milling

The cutter combines solid carbide substrate with a TiAlN coating to withstand elevated cutting temperatures and abrasive conditions. The 6 flutes and a pronounced 35–38° helix enable increased feed per tooth and stable chip evacuation, which means higher productivity in both slotting and peripheral milling. The geometry is optimised to balance cutting forces and heat management, reducing tool wear and preserving edge integrity over longer cycle times.

Stable clamping and concentricity for reliable tolerances

A cylindrical shank to DIN 6535 HB with shank tolerance h6 ensures concentric clamping in holders and minimises runout-related shortening of tool life. The neck relief and unequal pitch reduce the tendency to chatter, delivering smoother surface finishes and consistent tolerances during interrupted cuts or deep passes. These features lower the risk of rework and support predictable process windows on production equipment.

Universal material compatibility for fewer tool changes

Thanks to its substrate and coating, the tool is suitable for a wide material spectrum: steels, cast iron, temper castings, Cr‑Ni alloys, non‑ferrous metals and aluminium with silicon content, as well as abrasive workpieces. The combination of a fine‑grain carbide body and TiAlN enables both roughing and finishing operations without frequent tool swaps. For users less familiar with coatings: TiAlN forms a hard, oxidation‑resistant layer that protects the cutting edge at high temperatures and improves overall wear resistance.

Practical dimensions and handling for workshop integration

With an overall length 72 mm, effective length 30 mm and cutting length 6 mm, the long configuration offers extended reach for deep or recessed features while keeping the active flute length appropriate for stable cutting. The tool includes a protective chamfer 0.2 mm (45°) and a relief measure listed as 9.7 mm, aiding in safe handling and initial engagement. The design supports vibration‑reduced machining, helping to maintain cycle consistency on CNC milling centres and reducing the need for excessive fixture rigidity.

Contact Metav Werkzeuge for tailored application advice and fast supply from Emmerich — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930

Technical Data

• Article number: 2000866938NW
• Standard: DIN 6527
• Type: Solid carbide end mill, long

Dimensions & Cutting Data

• Diameter: 10 mm
• Overall length: 72 mm
• Cutting length: 6 mm
• Effective length: 30 mm
• Shank diameter: 10 mm
• Flutes: 6
• Helix angle: 35–38°
• Cutting direction: right‑hand cutting
• Shank tolerance: h6

Materials & Special Features

• Coating: TiAlN
• Material: solid carbide (VHM)
• Shank: cylindrical to DIN 6535 HB
• Pitch: unequal pitch for reduced vibration
• Neck relief present
• Protective chamfer: 0.2 mm, 45°
• Relief measure: 9.7 mm
• Suitable for: steel, cast iron, Cr‑Ni steels, non‑ferrous metals, aluminium with silicon, abrasive materials
• Application: vibration‑reduced machining, suitable for roughing and finishing

FAQ

What materials is the cutter suitable for?
The TECWERK Solid Carbide End Mill D10 mm is suitable for steels, cast iron, temper castings, Cr‑Ni alloys, non‑ferrous metals and aluminium containing silicon, as well as abrasive materials.

What advantages does the TiAlN coating provide?
The TiAlN coating on this cutter increases heat resistance and wear protection, extending tool life during high‑temperature or abrasive milling operations.

Which shank and tolerance standards apply?
The tool features a cylindrical shank to DIN 6535 HB with h6 tolerance for precise clamping and reduced runout.

Is the geometry suitable for finishing operations?
Yes — the combination of six flutes, unequal pitch and the 35–38° helix enables both efficient material removal and fine surface finishes, making the tool appropriate for finishing as well as roughing.

What is the SKU for ordering or reference?
Reference SKU 2000866938NW for ordering and technical enquiries regarding this TECWERK end mill.

TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund