10mm Full Radius Cutter 24mm Cutting Length TiAlN Coated Solid Carbide 2-Flute Short, 30° Helix - TECWERK

Take advantage of a combination of solid carbide construction, TiAlN surface protection and a two-flute, centre-cutting geometry to improve milling reliability and cycle times. Order this cutter directly via Metav Werkzeuge or contact our consultants for tailored technical guidance.

Full-radius end mill Ø10 mm, solid carbide, TiAlN – TECWERK

A Full-radius end mill Ø10 mm designed for general-purpose milling, centre plunging and profiling in steel, cast iron and a wide range of non‑ferrous and special alloys

*Solid carbide, fine-grain, TiAlN-coated
*2-flute design for efficient chip evacuation
*Centre cutting for plunging and profile milling
*Cylindrical shank to DIN 6535 HB, h6 tolerance

Faster throughput with predictable tool life

The solid carbide construction combined with the TiAlN coating delivers a robust balance of wear resistance and thermal stability, making the tool a dependable choice for repetitive production work. The short design and two-flute geometry promote effective chip clearance, which reduces heat build-up and the risk of re-cutting chips when machining medium to high-strength steel or abrasive plastics. These characteristics translate into consistent component quality and fewer unplanned tool changes, supporting measurable improvements in machining throughput and process stability.

Precision geometry for demanding contours and plunges

A centre-cutting geometry enables safe vertical entry for pocketing and plunge operations, while the 30° helix supports smooth cutting forces and a good surface finish on contours. The cutter’s cylindrical shank to DIN 6535 HB with h6 tolerance ensures secure clamping and concentricity in standard toolholders, reducing runout and improving dimensional accuracy. The effective length of 24 mm provides reach for many common profile milling tasks without compromising stiffness, so features retain tight tolerances even on small machines.

Broad material suitability and application clarity

This end mill is specified for use on a wide material spectrum: steel, cast iron, stainless (INOX), non‑ferrous metals and special alloys are all listed as very well suited. The fine‑grain carbide substrate combined with the TiAlN layer improves oxidation resistance and sustained hardness at elevated temperatures, making the cutter a practical option where both wear resistance and edge integrity are required. For tasks that demand reliable finishing or roughing in mixed batches, the combination of geometry and coating reduces the need for multiple tool types.

Practical benefit for workshop and production planning

Adopting this tool in a production setting reduces complexity: one short, centre‑cutting full‑radius cutter can handle plunging, slotting and profile passes across several material families, which simplifies tooling lists and inventory management. The two‑flute layout supports higher feed rates in non‑ferrous work while retaining acceptable chip control in steels. For procurement and production planners, the predictable behaviour of a coated fine‑grain carbide cutter helps to calculate tool life and set realistic maintenance intervals, contributing to a smoother workflow and lower per-part tooling cost.

Contact Metav Werkzeuge for a tailored quotation or technical consultation on the TECWERK full‑radius end mill and secure reliable supply from our Emmerich location

Technical data

• Article number: 2000866975NW
• Manufacturer: TECWERK
• Product type: Full-radius end mill

Facts

• Diameter: 10 mm
• Effective length: 24 mm
• Overall length: 66 mm
• Cutting length: 2 mm
• Shank diameter: 10 mm
• Flutes: 2
• Helix angle: 30°
• Right‑hand cutting
• Centre cutting capability
• Shank tolerance: h6

Special features

• Solid carbide, universal fine-grain
• TiAlN coating
• Cylindrical shank to DIN 6535 HB
• Short type, two‑cutting edges
• Suitable for steel, cast iron, INOX, non‑ferrous metals and special alloys
• Type N; centre cutting; 30° helix angle

FAQ

What materials is this cutter suitable for?
The TECWERK full‑radius end mill is specified as very well suited for steel, cast iron, stainless (INOX), non‑ferrous metals and special alloys, making it versatile for mixed production batches.

Can the cutter be used for plunge milling?
Yes, the centre‑cutting geometry permits vertical plunging; the cutter’s design supports controlled entry into the workpiece for pocketing and similar operations.

How does the TiAlN coating benefit machining?
The TiAlN coating increases oxidation resistance and maintains hardness at higher temperatures, which helps preserve cutting edges and extends tool life under elevated heat and heavier cutting conditions.

Does the shank fit standard toolholders?
The cylindrical shank complies with DIN 6535 HB and is manufactured to an h6 tolerance, ensuring accurate seating and reduced runout in standard holders.

Why choose a two‑flute design for this application?
A two‑flute layout improves chip evacuation and allows higher feed rates in non‑ferrous materials, while still providing satisfactory performance in steels when combined with solid carbide and TiAlN.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund