16mm Solid Carbide End Mill 55mm Cutting Length TiAlN Coating 35-38° Helix, DIN 6527 - TECWERK

Take advantage of the solid carbide construction and TiAlN high-temperature coating for longer tool life and consistent surface quality in mixed production tasks; order the TECWERK cutter directly via Metav Werkzeuge or request application advice from the consultants at Metav Werkzeuge.

TECWERK Solid Carbide End Mill D16 mm — Extra-long, TiAlN, 6-flute

The TECWERK Solid Carbide End Mill D16 mm is an extra-long, six-flute cutter engineered for both roughing and finishing across a wide range of metals in CNC milling applications.

• Solid carbide (VHM) for high rigidity
• TiAlN coating for heat resistance
• Extra-long 6-flute design for deep cuts
• Helix 35–38° for smooth chip evacuation

Increased stiffness and consistent chip control for reliable results

The combination of a solid carbide body and a six-flute geometry delivers high bending stiffness and repeatable cutting behaviour in interrupted and continuous cuts. The fine-grain carbide substrate improves edge stability, while the multi-flute design increases metal removal rate without compromising surface finish. For workshops seeking predictable cycle times, this geometry reduces vibration and helps maintain tolerances over longer tool life. The DIN-compliant shank ensures secure clamping in standard toolholders and supports consistent concentricity for demanding components.

Universal suitability across common and alloyed materials

Designed for universal application, the tool shows very good suitability for steel, cast iron, stainless (Cr-Ni) steels and non-ferrous alloys, including aluminium with silicon content. The cutter’s geometry and coating make it capable of both aggressive machining and fine finishing, so fewer tool changes are required during mixed-material batches. For operations that alternate between roughing and finishing, the tool provides a balance of cutting performance and surface integrity, helping to streamline workflow and reduce setup complexity.

Coating and flute design that extend tool life and resist heat

The TiAlN surface treatment provides thermal stability at elevated cutting temperatures and reduces adhesion of workpiece material to the cutting edge. Combined with an unequal pitch and a 35–38° helix, the design promotes steady chip evacuation and lowers the risk of built-up edge, particularly when machining abrasive or silicon-containing aluminium alloys. A 45° protective chamfer at the cutting edge and a neck relief (free-cutting neck) further protect the tool in shoulder milling and allow deeper engagement without chatter, supporting both productive roughing passes and fine finishing.

Practical handling, mounting and process benefits

The cutter features a cylindrical shank manufactured to DIN 6535 HB with h6 tolerance for precise clamping and reduced runout. With an effective length of 55 mm and an overall length of 108 mm, the extra-long configuration is suited to deep-pocket and stepped features where reach is essential. Right-hand cutting and a short protection chamfer of 0.2 mm simplify start-up and entry into the workpiece. For process planning, the combination of vibration-damped geometry and high-temperature coating yields longer tool intervals and fewer interruptions, contributing to steady shop-floor throughput and lower overall tooling consumption.

For tailored machining parameters or to reserve the TECWERK D16 solid carbide end mill from Metav Werkzeuge in Emmerich, contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss specific applications and delivery options

Technical Data

• Article number: 2000866998NW
• Manufacturer: TECWERK
• Standard: DIN 6527
• Shank standard: DIN 6535 HB
• Coating: TiAlN
• Material: VHM (solid carbide)

Facts

• Diameter: 16 mm
• Overall length: 108 mm
• Effective length: 55 mm
• Cutting length: 6 mm
• Shank diameter: 16 mm
• Flutes: 6
• Helix angle: 35–38°
• Protective chamfer: 0.2 mm
• Shank tolerance: h6

Special features

• Extra-long design
• Unequal pitch for reduced vibration
• Right-hand cutting
• Neck relief (free-cutting neck)
• 45° protective chamfer
• Suitable for steel, cast iron, Cr‑Ni steels, non-ferrous metals
• Effective for aluminium with silicon content and abrasive materials
• Vibration-damped geometry for roughing and finishing

FAQ

What materials can this solid carbide end mill machine effectively?
The TECWERK D16 solid carbide end mill is designed for very good performance in steel, cast iron, Cr‑Ni (stainless) steels and non-ferrous metals, including aluminium with silicon content and certain abrasive materials.

Is the shank compatible with standard toolholders?
Yes; the cutter has a cylindrical shank manufactured to DIN 6535 HB with an h6 tolerance, ensuring secure clamping in standard collets and holders.

Can this tool be used for both roughing and finishing operations?
The combination of unequal pitch, six flutes and TiAlN coating makes the cutter suitable for productive roughing passes as well as fine finishing, reducing the need for multiple specialised tools.

Does the extra-long configuration affect stability?
The extra reach is balanced by a stiff solid carbide construction and geometry optimised for vibration damping, allowing deeper engagement while maintaining surface quality.

What advantage does the TiAlN coating provide?
TiAlN increases thermal resistance at the cutting edge, reduces adhesion and wear at higher cutting temperatures, and generally extends tool life in dry and high-temperature conditions.

Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund