32mm 45° Angle Milling Cutter HSS-Co DIN 1833 D Type N, 12 Teeth - ALPEN-MAYKESTAG GmbH

Combining HSS‑Co hardness, a precise 45° geometry and a secure cylindrical shank with drive flat, this cutter enables consistent chamfering in structural and tempered steels as well as short‑chip non‑ferrous metals. Order the ALPEN‑MAYKESTAG angle milling cutter directly via Metav Werkzeuge or ask our consultants if needed.

ALPEN‑MAYKESTAG Angle milling cutter DIN 1833 D Type N — 45° Ø 32 mm, HSS‑Co, 12 teeth

The ALPEN‑MAYKESTAG Angle milling cutter DIN 1833 D Type N is a 45° chamfering tool for milling operations on construction, case‑ and tempering steels and for short‑chip non‑ferrous metals, supplied with a cylindrical shank including a drive flat.

• 45° angle geometry for precise chamfers
• HSS‑Co grade for enhanced wear resistance
• Cylindrical shank with drive flat, 12 teeth

Precision and material performance for reliable chamfering

The cutter is manufactured from HSS‑Co, a cobalt‑alloyed high‑speed steel that combines toughness and heat resistance to extend tool life under intermittent loads. This material choice is particularly beneficial when working with structural and tempering steels, where heat buildup and abrasive wear are common. The combination of tool steel and geometry produces uniform edge formation and reduces the risk of premature failure, supporting consistent part quality in series production or workshop runs. The result is efficient material removal with predictable tool life, which contributes to lower process costs and less frequent tool changes.

Geometry and cutting behaviour that improve cycle times

With a defined 45° geometry, 32 mm nominal diameter and 12 teeth, the cutter creates clean chamfers while maintaining stable cutting forces. The right‑hand cutting orientation ensures standard rotational direction compatibility with most milling setups. Multiple teeth distribute the cutting load across the flange, enabling higher feed per tooth and smoother surface finish on chamfered edges. The design also encourages controlled chip formation for short‑chip materials, limiting clogging and promoting steady chip evacuation, which in turn helps to keep cycle times short and machining predictable.

Secure clamping, standards compliance and practical workshop use

A cylindrical shank with drive flat offers reliable seating in collets and toolholders, reducing slippage during higher torque operations. Conformity to DIN 1833 D and Type N descriptors indicates a standardised geometry and application scope, simplifying selection and replacement in industrial tool inventories. The cutter is supplied single (packaging unit 1) and is suited to toolrooms, maintenance departments and production lines that require reproducible chamfering. For identification and ordering, see article number 4117802048NW. For complex applications or dimensional tolerances, compatibility with specific holders and spindle interfaces should be verified prior to operation.

For dependable 45° chamfering with ALPEN‑MAYKESTAG quality, contact Metav Werkzeuge in Emmerich for ordering or technical advice at info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: 4117802048NW
• Description: Angle milling cutter DIN 1833 D Type N, 45°, HSS‑Co
• Manufacturer: ALPEN‑MAYKESTAG GmbH
• Packaging unit: 1

Facts

• Diameter: 32 mm
• Cutting angle: 45°
• Teeth: 12

Special features

• Cutting material: HSS‑Co
• Standard: DIN 1833 D
• Type: N
• Right‑hand cutting
• Cylindrical shank with drive flat
• For structural, case and tempering steels; for short‑chip non‑ferrous metals

FAQ

Which materials is the cutter suitable for?
The ALPEN‑MAYKESTAG angle milling cutter is suitable for milling construction, case and tempering steels and for short‑chip non‑ferrous metals, thanks to the HSS‑Co grade and 45° geometry.

What does DIN 1833 D Type N indicate?
DIN 1833 D with Type N describes a standardised angle cutter geometry and application class; this ensures the tool’s dimensions and functional purpose are compatible with recognised industrial chamfering practices.

Which holders and spindles are compatible with the cylindrical shank?
The cutter’s cylindrical shank with drive flat is designed for secure clamping in standard collets and toolholders that accommodate a plain shank and provide positive drive via the flat.

Is the tool suitable for series production and repeated use?
Yes; the HSS‑Co construction and multiple teeth distribution make the cutter appropriate for repeated chamfering cycles, offering a balance of wear resistance and repairability typical for cobalt‑alloyed high‑speed steels.

What is the cutting direction and how does it affect the operation?
The cutter is right‑hand cutting, matching conventional spindle rotation; this delivers predictable chip flow and surface finish when used in standard milling configurations.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com