Precision boring heads and taper adaptors for accurate large-diameter holes
Precision boring heads and taper adaptors enable machining of highly accurate, round bores on milling machines and deliver tight fits for assembly and tooling. These systems are used to produce large-diameter, close-tolerance holes by combining robust boring heads, matched taper adaptors and appropriate boring bars, allowing operators to achieve repeatable concentricity and surface finish. Ideal for metalworking applications where hole accuracy and fit are critical, they reduce rework and improve assembly reliability by providing controlled material removal and straightforward tool setup.
VBH620 Precision Boring Head Set BT-40, M16x2.0 Thread - Vertex
Benefit from precise adjustment via the M16x2.0P fine thread and the stable BT-40 taper, combined with a solid 6.5 kg construction that supports consistent internal machining results. Order the VBH620 directly via Metav Werkzeuge or ask our consultants if needed. VBH620 Precision boring head set (BT-40, M16x2.0P) by Vertex VBH620 Precision boring head set is a finely adjustable tool for high-accuracy internal machining tasks on milling machines and machining centres. Precision boring head set BT-40 M16x2.0 fine-adjustment thread Robust construction, 6.5 kg mass Compatible with Vertex machining centres Accuracy that stabilises production The design focuses on delivering repeatable precision for internal bores. The combination of a rigid BT-40 taper and a fine M16x2.0P adjustment thread enables micro-adjustments without frequent recalibration, which translates into fewer scrap parts and tighter tolerances. Interpreting the mechanical interface is straightforward: the taper guarantees secure clamping in the spindle, while the fine thread provides controlled cutting-edge displacement, improving finish and dimensional control for critical assemblies. Designed for smooth integration into the machine park Designed to fit standard toolholders, the set integrates with conventional milling spindles and machining centres using the BT-40 interface. With a mass of 6.5 kg, the assembly benefits from increased inertia, reducing chatter and improving surface quality when boring at moderate feed rates. The mechanical arrangement supports consistent cutting geometry, making the set suitable for series production where stability and time-efficient changeover are priorities. The VBH620 configuration allows technicians to convert set-up accuracy into measurable process reliability. Practical workshop advantages and uptime improvement The construction emphasises serviceability and robust operation, which helps to reduce unplanned downtime in daily shop-floor use. The precise adjustment mechanism minimises the need for repeated tool trials and enables faster set-ups, lowering cycle-time per component. For workshops focused on delivering consistent bore sizes and surface integrity, this boring head set supports predictable outcomes and reduces rework, contributing to overall process economy and throughput. Contact Metav Werkzeuge for tailored technical advice on the VBH620 precision boring head set — email info@metav-werkzeuge.com or call +49 2822 7131930 for application support and compatibility checks Technical Data SKU: VBH620-BT40 GTIN: 4061905089534 Manufacturer: Vertex Weight: 6.5 kg Thread: M16x2.0P Facts Taper: BT-40 Article number: VBH620-BT40 Special features Precision boring head set Suitable for machining centres Robust construction FAQ What machines is this boring head compatible with? The VBH620 precision boring head set is compatible with machines accepting a BT-40 taper and is intended for use on milling machines and machining centres. How is fine adjustment achieved on the set? Adjustment is made via the M16x2.0P fine thread, which allows precise, incremental displacement of the cutting edge for accurate bore diameter control. Does the weight influence machining stability? Yes, the 6.5 kg mass contributes to spindle inertia and helps reduce vibration during boring, supporting improved surface finish and dimensional stability. Is this set suitable for series production? The mechanical stability and fine-adjustment capability make the set well suited to series production where repeatable bore quality and reduced set-up time are required. Who manufactures the product and where can technical details be checked? The product is manufactured by Vertex; further technical compatibility and application advice can be obtained from Metav Werkzeuge or directly through the factory documentation. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
VBH620 Precision Boring Head Set BT-50, M24x3.0P Thread - Vertex
Take advantage of the combination of precise M24 fine adjustment, a BT-50 machine interface and a solid 8 kg mass for stable bore finishing — a compact package that supports consistent production tolerances. Order the VBH620 precision boring head set directly via Metav Werkzeuge or contact our advisers for compatibility checks. VBH620 Precision Boring Head Set — BT-50 Interface, M24 Fine Adjustment (Vertex) The VBH620 is a precision boring head set engineered for fine internal diameter adjustment in machining centres and conventional toolroom machines High-precision fine adjustment M24 thread Compatible with BT-50 taper systems Solid 8 kg mass for machining stability Micrometre-level control for consistent bore accuracy The VBH620 delivers fine radial adjustment via an M24 × 3.0 pitch thread, enabling controlled, repeatable corrections in small increments. This mechanism converts rotary motion into precise linear displacement, so a single indexed turn produces a predictable radial change; that behaviour simplifies process planning and reduces the need for iterative trial cuts. The combination of a robust adjustment screw and carefully finished bearing surfaces provides consistently low runout, which directly benefits bore cylindricity and surface finish. For production-oriented shops, the result is fewer scrapped parts and reduced rework time, a clear efficiency gain. Stable interface and reduced vibration for superior surface quality A correctly matched taper and sufficient mass are fundamental for stability during internal finishing. The VBH620’s BT-50 compatibility ensures a direct, standardised connection to spindles that accept this shank form, while the unit’s 8 kg mass contributes to inertial damping under cutting loads. The result is improved tool stability, less chatter and a more uniform surface texture inside the bore. Where processes demand tight tolerances and repeatable results, this combination of secure clamping and solid mass reduces variability and supports predictable cycle times. Streamlined integration and straightforward workshop handling The set is designed for straightforward integration into existing tool inventories that use BT-50 holders and standard fine-adjustment procedures. The M24 fine adjustment is familiar to machinists and maintenance teams, which shortens setup time and reduces training overhead. Routine checks and calibration follow established practices for boring heads: verify runout, confirm adjustment indexing and secure clamping in the spindle before cutting. For queries about machine compatibility, setup advice or detailed specifications, Metav Werkzeuge’s technical advisers are available by email or phone to provide targeted support. Reliable sourcing and service from a precision partner Procurement choices influence throughput and quality assurance. Vertex supplies the component with an industrial pedigree, and Metav Werkzeuge offers a European distribution and quality-filtering point from its Emmerich warehouse. This supply chain arrangement combines manufacturing competence with localised service: rapid delivery options, consolidated purchasing for workshop fit‑outs and access to specialist advice. The arrangement supports workshops and industrial users who value predictable availability and a consistent quality standard across their metrology and tooling purchases. Contact Metav Werkzeuge for expert advice on Vertex tooling and secure the VBH620 precision boring head set from our Emmerich warehouse. Technical Data SKU: VBH620-BT50 GTIN: 4061905090936 Manufacturer: Vertex Core technical data Weight: 8 kg Thread: M24 × 3.0 pitch eClass: 21041590 Special features Precision boring head set BT-50 taper compatibility Fine radial adjustment via M24 thread FAQ Which machine taper fits this boring head set? The VBH620 precision boring head set accepts a BT-50 taper interface, matching standard BT-50 toolholders and spindles for straightforward installation. What type of adjustment does the set use for bore correction? Adjustment is performed via an M24 × 3.0 fine-thread mechanism on the VBH620, giving predictable, micrometre-scale radial changes for accurate finishing. Is the VBH620 heavy enough to reduce vibration during cutting? With a mass of 8 kg, the VBH620 provides additional inertial damping compared with lighter assemblies, supporting improved stability and surface quality in many finishing operations. Can this set be integrated into an existing tool setup quickly? Yes — the VBH620 by Vertex is designed for compatibility with standard BT-50 systems and familiar fine-adjustment practice, enabling rapid integration into established workflows. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
VBH620 Precision Boring Head Set SK-40, M16x2.0 Thread - Vertex
Take advantage of the combination of tight dimensional control, broad machine compatibility and robust construction to keep machining tolerances consistent and setup times low. The set’s SK-40 compatibility and M16 x 2.0 thread allow integration with conventional toolholders while the compact mass supports stable boring runs. Order the set directly via Metav Werkzeuge or consult the team for specification matching and delivery options. VBH620 Precision Boring Head Set — high-precision adjustment with SK-40 taper VBH620 is a precision boring head set designed for fine internal machining on milling machines and machining centres, compatible with standard SK-40 taper toolholders and suited to tasks requiring repeatable bore accuracy. High-precision adjustment for tight tolerances SK-40 taper compatibility for common toolholders M16 x 2.0 thread for secure cutter mounting Robust assembly weight of 6.5 kg for stability Stable accuracy for repeatable bores The set delivers consistent bore accuracy through finely graduated adjustment, which reduces the need for repeated trial cuts. The integrated adjustment mechanism provides small, measurable increments for diameter correction, enabling predictable material removal and repeatable results across series production. This reduces scrap rates and shortens setup iterations, supporting lean machining workflows while maintaining close tolerances on internal diameters. Broad machine compatibility and secure mounting Compatibility with the SK-40 taper ensures straightforward integration into a wide range of milling spindles and toolholders commonly used in machining centres. The M16 x 2.0 mounting thread secures the cutting head and accessories with standardised engagement, preventing axial play during heavy feeds. The tool’s mass (approx. 6.5 kg) contributes to damping of vibration during boring operations, improving surface finish and protecting cutting edges from undue chatter. Practical design for workshop efficiency The construction combines serviceability and robustness: modular components simplify changeover of cutting inserts and allow measured adjustments without disassembly. Where micro-adjustments are required, the clear mechanical indexing and labelled increments expedite setup. The design reduces calibration time and supports efficient changeovers between workpieces, benefiting production environments that demand both precision and throughput. Built trust — engineered by a recognised manufacturer Manufactured under the Vertex brand, the set reflects established standards in precision toolmaking and is intended for professional workshops and industrial users seeking a reliable boring solution. The configuration is optimised for everyday machining tasks as well as for finer, precision-critical operations, providing a practical balance between adjustability and mechanical stability. Contact Metav Werkzeuge in Emmerich for application advice, configuration checks and delivery information regarding the Vertex VBH620 precision boring head set Technical data Article number: VBH620-SK40 Manufacturer: Vertex GTIN: 4061905090523 Facts Weight: 6.5 kg Thread: M16 x 2.0 Special features Shank type: SK-40 Model: VBH620 FAQ What machines is the boring head set compatible with? Compatibility is achieved via the SK-40 taper; the VBH620 fits machines and toolholders accepting an SK-40 shank and is suitable for milling machines and machining centres. How is diameter adjustment performed on the set? Diameter correction uses a fine mechanical adjustment mechanism; the VBH620 provides measured increments for predictable material removal and repeatable bore sizes. Can the VBH620 handle heavy cuts without vibration? The assembly mass of 6.5 kg and stable mounting via SK-40 reduce vibration during conventional boring operations, improving finish and cutter life. Which thread is used for cutter mounting and accessories? The set uses an M16 x 2.0 thread for cutter attachment and accessory fixation, ensuring secure engagement and standardised compatibility Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
VBH620 Precision Boring Head Set SK-50, M24x3.0 Thread - Vertex
Take advantage of high-precision adjustment, robust mass for stable machining and direct compatibility with SK-50 toolholders to improve bore repeatability and reduce rework; order the VBH620 directly via Metav Werkzeuge or consult our specialists for application guidance. VBH620 precision boring head set — SK-50 compatibility, M24x3.0 adjustment The VBH620 is a precision boring head set designed for fine, repeatable internal diameter machining on toolholders and machining centres using SK-50 collets. Fine M24x3.0 adjustment thread Compatible with SK-50 collets Stable 7.8 kg mass for vibration damping Consistent bore accuracy for demanding parts A precision boring head delivers controlled incremental movement to finish bores to tight tolerances. The VBH620 employs a fine M24x3.0 thread for micro-adjustment, enabling predictable increments without complex measuring routines. This mechanical adjustment method improves repeatability from setup to setup and reduces the need for manual rework. For production environments, this means fewer scrap parts and a more consistent output across batches. Stable mass and geometry that protect surface quality Mass and rigidity directly influence vibration and surface finish. The assembly’s 7.8 kg mass contributes to damping of spindle-induced vibration, stabilising the cutting edge and supporting a smoother finish. Combined with a compact, concentric construction, the result is reduced tool chatter and longer insert life. The design therefore supports both quality improvements and lower tooling costs over time. Seamless integration with SK-50 toolholding systems Compatibility with SK-50 collet systems simplifies tool-room logistics and shortens changeover times. The boring head set mates directly with standard SK-50 holders, preserving spindle concentricity and maintaining axial alignment during adjustment. The collet interface ensures secure clamping and straightforward removal for maintenance, making it suitable for heavy-duty CNC applications where reliable clamping and repeatable positioning are essential. Reliable manufacturer pedigree and traceable identification Produced by Vertex, the assembly is delivered with clear identification for procurement and traceability. The SK-50 interface and the M24x3.0 adjustment mechanism reflect industry-standard dimensions that facilitate documentation and spare-part planning. Using components with defined identifiers supports quality management systems and makes integration into existing production documentation straightforward. Contact Metav Werkzeuge for tailored advice on integrating the Vertex VBH620 into existing toolholder setups and to arrange immediate supply from Emmerich. Technical data Article number: VBH620-SK50 GTIN: 4061905091278 Manufacturer: Vertex Facts Weight: 7.8 kg Thread: M24x3.0P Collet type: SK-50 eClass: 21041590 Special features Precision boring head set Suitable for SK-50 collet systems SKU: VBH620-SK50 FAQ What machines is this boring head set compatible with? The VBH620 precision boring head set is designed for machining centres and lathes that accept SK-50 toolholders, providing a straightforward fit with standard SK-50 interfaces. How is fine adjustment achieved on the VBH620? Adjustment is carried out via the M24x3.0 thread, which allows micro-increments for bore diameter correction and dependable repeatability in serial production. Does the mass of the unit affect machining performance? Yes. The unit’s 7.8 kg mass improves vibration damping and contributes to a better surface finish and extended tool life during heavy cutting operations. Is the VBH620 suitable for high-precision finishing tasks? The VBH620 is engineered as a precision boring head set and is suitable for finishing operations where controlled incremental adjustment and stability are required to meet tight tolerances. Where can procurement and technical specification documents be obtained? Specification details and procurement identification are provided with the product; reference the SKU VBH620-SK50 and GTIN 4061905091278 when requesting documentation. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Boring and Facing Head Set, SK40 Collet Interface - Vertex
Take advantage of the combination of compatibility with SK-40 spindles and a broad Ø10–Ø110 mm working range to streamline machining tasks. The set delivers reliable clamping and flexible diameter adjustment for efficient facing and boring operations. Order the set directly via Metav Werkzeuge or consult our specialists for technical advice. Vertex VBHC-SK40-BC2 Facing and Boring Head Set — SK-40 shank, Ø10–Ø110 mm A compact VBHC facing and boring head set for SK-40 spindles, designed to provide precise diameter adjustment across a broad range for workshop and light industrial machining SK-40 shank for secure spindle mounting Adjustable diameter range Ø10–Ø110 mm Complete facing and boring head set Suitable for precision workshop applications Precision where it matters: consistent bore and face results The set is engineered to provide repeatable accuracy for internal diameters and facing operations. With a secure SK-40 mounting and fine adjustment across Ø10–Ø110 mm, the arrangement reduces the need for multiple tool changes and supports consistent part quality. The design focuses on measurable outcomes — reduced rework and predictable tolerances — which translate directly into lower cycle times and improved throughput on batch work and prototyping runs. Integration into the workshop: faster set-up, fewer interruptions This head set supports a pragmatic workflow by combining facing and boring capabilities in a single package. The versatile diameter range minimises tool inventories and simplifies changeover procedures on milling machines with SK-40 spindles. For shops aiming to improve process efficiency, the configuration offers tangible gains: quicker set-up, decreased spindle downtime and a clearer tooling strategy for mixed runs, saving both machine hours and operator effort. Operator benefits and everyday handling Operators benefit from intuitive adjustment and stable clamping that help maintain concentricity during operations. The set’s compatibility with standard SK-40 interfaces ensures straightforward deployment in existing machines without adaptor work. Clear, tool-centred functionality supports confident machining of precision components, allowing skilled staff to focus on cycle optimisation rather than compensating for tool instability. Typical applications and suitability Designed for facing and boring tasks in general workshop environments and light industrial use, the set is well suited to producing precise internal bores, shallow reaming operations and accurate face finishes within its diameter range. The compact arrangement is particularly useful for small-batch production, maintenance workshops and toolrooms that require a reliable, multi-purpose solution without expanding the tooling pool. Contact Metav Werkzeuge in Emmerich for tailored advice on the Vertex facing and boring head set VBHC-SK40-BC2 and to request further technical data or availability information by email or phone Technical data SKU: VBHC-SK40-BC2 GTIN: 4061905091643 ECLASS: 21041590 Set: yes Core data Diameter range: Ø10–Ø110 mm Shank type: SK-40 Special features Facing and boring head set configuration Suitable for precision workshop applications FAQ What diameter range does the set cover? The set covers a working diameter range of Ø10–Ø110 mm, enabling a wide variety of facing and boring tasks. Which spindle interface is required for mounting? The tooling is designed for machines with an SK-40 taper shank and mounts directly to compatible spindles. Is this set suitable for series production? Yes — the combination of stable clamping and an adjustable range makes the set suitable for small- to medium-series production and precision workshop work. What is included in the set? The VBHC-SK40-BC2 is supplied as a complete facing and boring head set intended for flexible use across the stated diameter range. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Face And Boring Head Set BT30, Set - Vertex
Take advantage of the BT‑30 compatibility and the wide Ø10–Ø110 mm working range to achieve stable, repeatable facing and boring operations; the compact 2.65 kg mass contributes to reduced vibration and reliable concentricity. Order the unit directly via Metav Werkzeuge or consult the team for integration advice. VBHC face and boring head set — BT‑30 taper, Ø10–Ø110 mm The VBHC is a face and boring head set for BT‑30 spindles, engineered for precise facing and internal machining tasks in workshop and CNC environments. BT‑30 taper compatibility Diameter range Ø10–Ø110 mm Complete face and boring head set Stable 2.65 kg mass for vibration dampening Precision delivered where cutting accuracy matters The set has been engineered to support accurate face machining and controlled boring across a broad diameter span. By combining a standard BT‑30 spindle interface with an adjustable cutting range of Ø10–Ø110 mm, the system reduces the number of tool changes and alignment steps required during a production run. The result is improved machining repeatability and fewer scrap parts, which is especially relevant for operations that demand tight runout and consistent surface finishes. The modular design of the set also enables straightforward calibration and repeatable seating in the spindle. Seamless integration into existing spindle systems Designed around a common spindle connection, the tool set enables fast, reliable mounting on BT‑30 capable machines. The standardised spindle taper interface shortens setup time and preserves spindle concentricity, which supports higher throughput without compromising accuracy. As a result, bench and CNC workshops can integrate the unit into multi-shift workflows with minimal downtime for changeover, making it a pragmatic choice where machine availability and process stability are priorities. Robust handling and operational stability The assembly’s mass of 2.65 kg provides natural damping during cutting, which helps to reduce chatter and maintain surface integrity on facing and internal-cut operations. The set concept bundles necessary components for immediate use, limiting handling complexity and simplifying inventory. Careful attention to mechanical balance and fit ensures that the head set holds cutting inserts and toolholders more securely, contributing to longer tool life and consistent results across repetitive runs. Practical applications and process benefits The head set is particularly suitable for workshops that require a compact solution for facing and internal machining with assured repeatability. With the adjustable diameter span and standard BT‑30 interface, the equipment lends itself to small-batch production as well as preparatory operations in larger series. Where setup efficiency and process reliability are sought, the combination of a complete set, standard spindle connection and stable mass offers clear gains in operational productivity and machining quality. Contact Metav Werkzeuge to discuss how the Vertex VBHC BT‑30 face and boring head set can be integrated into existing spindle workflows, to request technical documentation or to confirm current availability and delivery options. Technical data Article number: VBHC-BT30-BC2 GTIN: 4061905090950 Manufacturer: Vertex Model designation: VBHC Set: Yes Collet / spindle taper: BT‑30 Suitable diameter range: Ø10–Ø110 mm eCl@ss: 21041590 Weight: 2.65 kg Facts Weight: 2.65 kg Diameter range: Ø10–Ø110 mm GTIN: 4061905090950 eCl@ss: 21041590 Special features Face and boring head set Model: VBHC Collet type: BT‑30 Set configuration included Image assets: VBHC-R8-BC2-main.png; VBHC-BC2-detail.png FAQ Is the head set compatible with BT‑30 spindles? Yes. The set is designed for BT‑30 spindle interfaces and mounts directly to machines equipped with that taper. What diameter range can be machined with the set? The assembly covers a working range of Ø10–Ø110 mm, allowing both small and medium internal operations without frequent tool swaps. Does the delivery include all components required for immediate use? The product is supplied as a set, which groups the components necessary for facing and boring operations; specific consumables such as cutting inserts are not included unless stated otherwise. How does the weight affect machining performance? A mass of 2.65 kg helps to dampen vibrations during cutting, improving surface finish and runout stability in facing and boring tasks. Can the head set be used on both manual and CNC machines? Yes. With its standard BT‑30 connection and adjustable range, the set is suitable for bench-mounted and CNC applications where the taper is supported. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Face And Boring Head Set C-20, VBHC - Vertex
Reliable facing and boring performance with C‑20 collet clamping and a versatile Ø10–Ø110 mm diameter range. Compact and robust at 1.75 kg, the set delivers repeatable results and easier tool changes. Order the VBHC facing and boring head set directly via Metav Werkzeuge or ask our consultants if needed. VBHC — Facing and boring head set with C‑20 collet and Ø10–Ø110 mm range The VBHC facing and boring head set is designed for precise facing and adjustable boring tasks across a broad diameter range in workshop environments C‑20 collet for secure clamping Suitable for Ø10–Ø110 mm diameters Facing and boring head set for workshops Consistent clamping for repeatable machining results The core advantage of the set is the C‑20 collet system, which provides reliable clamping and improved repeatability during facing and boring operations. Secure clamping reduces runout and contributes directly to tighter tolerances, meaning fewer reworks and less inspection time. The design supports steady cutting conditions, which leads to consistent surface finish and dimensional stability on successive workpieces. Wide diameter coverage to reduce tool changes With an operating range of Ø10–Ø110 mm, the tooling set covers a broad span of diameters so that fewer tool swaps are required on jobs with mixed part sizes. This range translates into measurable productivity gains: setups remain simpler and cycle time is reduced when a single head can handle several bore sizes. The broad coverage also makes the kit a practical choice for small series and repair work where flexibility matters. Straightforward setup and precise finishing control The adjustable boring and facing functionality allows controlled material removal and fine-tuning of bore dimensions for a high-quality finish. The set includes the components necessary for routine adjustments and balancing, so users can achieve the desired bore accuracy without complex calibration. The boring head geometry and stable clamping contribute to uniform cutting engagement and stable chip evacuation, improving both finishing and tool life. Compact design that fits busy workshops Weighing 1.75 kg, the kit is compact yet robust, convenient to store and easy to handle during tool changes. The lightweight package supports efficient workshop logistics while maintaining the mechanical integrity required for precision work. Backed by a trusted manufacturing pedigree, this tooling set is suitable for users who prioritise dependable performance and concise workshop workflows. For tailored advice on integrating the VBHC set into existing tooling arrangements, contact Metav Werkzeuge—our consultants will assist with specification matching and order processing. Technical data SKU: VBHC-C20-BC2 GTIN: 4061905091599 eClass: 21041590 Facts Weight: 1.75 kg Diameter range: Ø10–Ø110 mm Set: yes Special features Collet type: C‑20 Product family: VBHC Manufacturer: Vertex Gallery image available FAQ What diameter range does the set cover? The kit covers diameters from Ø10–Ø110 mm, enabling a wide variety of facing and boring tasks. Which collet system is used for clamping? Clamping is performed with a C‑20 collet system to ensure secure grip and reduced runout. Is the VBHC supplied as a complete set? Yes, the VBHC facing and boring head set is supplied as a complete kit for workshop use (SKU VBHC-C20-BC2). What is the unit weight of the set? The complete set weighs 1.75 kg, offering a compact solution that is easy to handle. Who manufactures this tooling set? This tooling is manufactured by Vertex and delivered as a VBHC family product. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Face And Boring Head Set For MT‑4 Collet, Toolholder VBHC - Vertex
Combine reliable MT‑4 mounting with a wide Ø10–Ø110 mm working range to speed setups and maintain consistent finishing quality. Order the VBHC facing and boring head set directly via Metav Werkzeuge or request specialist advice to confirm compatibility and delivery. VBHC facing and boring head set — MT‑4 taper, Ø10–Ø110 mm compatibility by Vertex The VBHC facing and boring head set is a compact, workshop‑oriented solution for precision facing and internal turning on machines with an MT‑4 spindle taper. MT‑4 taper for secure spindle mounting Compatible with Ø10–Ø110 mm measuring range Robust construction, total weight 2.1 kg Delivered as a complete facing and boring set Precision finishing that reduces rework The facing and boring combination provides a controlled process for producing accurate face surfaces and true internal diameters. With an MT‑4 taper for stable spindle engagement and a balancing‑oriented design, the head set promotes high concentricity and repeatable results across multiple workpieces. The specified compatibility for the Ø10–Ø110 mm range enables consistent machining of medium‑sized bores without constant tool changes, which decreases the risk of scrap and shortens production cycles. Faster setup and predictable machining outcomes Delivered as a complete set, the equipment allows straightforward tool changeover and simplified calibration. The compact system reduces fixture complexity and supports a quick setup philosophy: once mounted in an MT‑4 spindle, the head set maintains its position and alignment, cutting down machine downtime between operations. The overall mass of 2.1 kg contributes to steady cutting behaviour, minimising vibration and improving surface finish without the need for extensive ancillary support. Robust design for everyday workshop use Manufactured by Vertex to industrial tolerances, the set is designed for repetitive tasks in small to medium production runs. The construction emphasises durability and serviceability, giving long tool life under standard operating conditions. Compatibility with common measuring and adjustment ranges in the Ø10–Ø110 mm band helps integrate the head set into existing workflows and measurement routines, supporting consistent quality control and easier part inspection. Contact Metav Werkzeuge for tailored advice on the Vertex VBHC facing and boring head set with MT‑4 taper and to arrange supply from our Emmerich facility Technical data Article number: VBHC-MT4-BC2 GTIN: 4061905088872 ECLASS: 21041590 Core specifications Weight: 2.1 kg Taper type: MT‑4 Measuring compatibility: Ø10–Ø110 mm Set contents & features Facing and boring head set Delivered as a complete set Manufacturer: Vertex FAQ What machines are compatible with this head set? The VBHC facing and boring head set by Vertex is designed for machines that accept an MT‑4 spindle taper and can be used wherever MT‑4 tooling is supported. Which bore sizes can be machined with the set? The head set is compatible with work in the Ø10–Ø110 mm range, enabling facing and internal turning tasks within that band. Does the set support precision finishing? Yes, the Vertex VBHC set is engineered for consistent finishing, with a balanced design and MT‑4 mounting that promote concentricity and repeatable diameters. What is included and how is it supplied? The product is supplied as a complete facing and boring set under SKU VBHC-MT4-BC2, intended for immediate integration into workshop processes. Where can the weight and identification details be found? The Vertex VBHC set (SKU VBHC-MT4-BC2, GTIN 4061905088872) has a total weight of 2.1 kg and is delivered as a complete unit. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Face And Boring Head Set NT-30 Collet Holder, Set - Vertex
Combining precision facing, NT-30 collet compatibility and a compact 2.2 kg design, this set improves finishing consistency and reduces setup complexity in small and medium workshops. Order the VBHC Facing and Boring Head Set directly via Metav Werkzeuge or consult our technical advisers for collet matching and application advice. VBHC Facing and Boring Head Set (VBHC-NT30-BC2) — NT-30 collet, suitable for Ø10–Ø110 mm A VBHC Facing and Boring Head Set designed for precision facing and controlled boring operations on lathes and machining centres, compatible with NT-30 collet systems. Facing and boring set for precision machining Compatible with NT-30 collet systems Effective range Ø10–Ø110 mm Robust compact design, approx. 2.2 kg Accurate facing and controlled boring for consistent results The set delivers precise facing and controlled bore enlargement suitable for finishing and corrective machining. Facing creates a flat surface perpendicular to the spindle axis while boring enlarges or refines an existing hole; both operations demand repeatable alignment and stable cutting conditions. With these core capabilities, the toolset supports reliable dimensional outcomes and improved part uniformity, translating into fewer reworks and steadier production runs. Secure clamping and adaptable diameter range Built for use with NT-30 collets, the head set accepts a broad workpiece interval of Ø10–Ø110 mm, providing flexibility across different job sizes. The NT-30 interface is a common industry standard that ensures concentric clamping and firm grip during facing and boring tasks. This compatibility reduces the need for bespoke adapters and simplifies tooling logistics when integrating the head set into existing collet-based systems. Compact construction that suits busy workshops With a compact footprint and an approximate mass of 2.2 kg, the assembly balances accessibility with stable handling during mounting and removal. The relatively low weight contributes to easier manipulation when changing setups and can reduce the load on handling equipment. The compactness also helps maintain workable clearances on small lathes and machining centres, supporting efficient workflow in space-restricted shops. Practical integration and Vertex reliability Designed as a versatile finishing solution, the set integrates into standard NT-30 tooling chains and supports common facing and boring tasks without complex adaptations. Supplied as a coordinated set, it simplifies inventory and tooling decisions for general workshop and maintenance applications. As a Vertex product, the toolset aligns with established industrial expectations for consistency and availability, making it suitable for routine production environments that prioritise dependable performance. For reliable facing and boring capabilities from a recognised brand, contact Metav Werkzeuge for tailored advice on NT-30 compatibility and delivery options from Emmerich — our specialists will assist with technical matching and order processing. Technical Data Article number: VBHC-NT30-BC2 GTIN: 4061905089114 Weight: 2.2 kg Collet type: NT-30 Suitable range: Ø10–Ø110 mm eClass: 21041590 ETIM: EC001959 Facts Weight: 2.2 kg Diameter range: Ø10–Ø110 mm SKU: VBHC-NT30-BC2 GTIN: 4061905089114 Special features Set for facing and boring operations Compatible with NT-30 collet systems Compact, workshop-oriented design Manufacturer: Vertex FAQ What machines is the set compatible with? The VBHC Facing and Boring Head Set is intended for use on lathes and machining centres equipped to accept NT-30 collet tooling. Which collet type is required for this head set? The head set is compatible with NT-30 collets and is supplied for integration into NT-30 tooling systems. What diameter range does the set cover? The tooling supports a working diameter range of Ø10–Ø110 mm for facing and boring tasks. How heavy is the complete set? The assembled set has an approximate weight of 2.2 kg, facilitating handling and mounting in typical workshop environments. Is this a Vertex product and how is it identified? Yes, this is a Vertex product and is identified by SKU VBHC-NT30-BC2 and GTIN 4061905089114. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Face and Boring Head Set With MT2 Collets, Threaded Mount - Vertex
Take advantage of precise diameter coverage Ø10–Ø110 mm, MT‑2 taper compatibility, and a ready-to‑use set format to reduce setup time and maintain consistent facing and boring quality. Order the VBHC Facing and Boring Head Set directly via Metav Werkzeuge or ask our consultants if needed. VBHC Facing and Boring Head Set — MT‑2 mounting, Ø10–Ø110 mm The VBHC Facing and Boring Head Set provides a compact solution for accurate face machining and internal boring on small to medium diameters, ideal for shops seeking quick setup and repeatable results Universal MT‑2 taper mounting Wide diameter range Ø10–Ø110 mm Precision ground for repeatable results Supplied as a complete set Precision where consistent results matter High‑precision machining starts with stable tooling. The facing and boring head combination delivers consistent concentricity across the specified diameter range, reducing rework and scrap. The MT‑2 mounting ensures firm seating in standard toolholders, while the set format keeps all components aligned for quick changeovers. With a compact overall mass of 1.66 kg, the assembly minimises spindle load without sacrificing rigidity. These factors combine to improve cycle‑time predictability and support higher first‑pass yields in production and jobbing environments. Faster integration into existing machines and processes Compatibility with common taper systems and a clear diameter span of Ø10–Ø110 mm enables straightforward integration into lathes and light milling rigs. The modular nature of the set allows precise adjustments for facing depth and bore diameter, which helps to shorten the machine‑set time between operations. The result is reduced non‑productive time and simplified tool inventory management, supporting leaner workflows and more reliable planning for batch production or prototyping. Ready for immediate shop use with measurable benefits Supplied as a complete set, the VBHC group reduces the need for ad‑hoc purchases of accessory components, offering a pragmatic route to standardised tooling. The precision of the ground components supports repeatable surface finishes and dimensional control, which is particularly valuable for assemblies where tolerances are tight. In practice, this means fewer inspection cycles and a steadier throughput — measurable advantages that translate into improved operational efficiency. Contact Metav Werkzeuge to check VBHC compatibility with existing tooling, arrange a supply from Emmerich and secure a reliable delivery plan via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: VBHC-MT2-BC2 GTIN: 4061905088704 Brand: Vertex Core dimensions and weight Weight: 1.66 kg Diameter range: Ø10–Ø110 mm Mounting taper: MT‑2 eClass: 21041590 ETIM: EC001959 Set contents and features Set: facing and boring head set Suitable for precision facing and boring operations Supplied as a complete set Product images available in gallery FAQ What operations is this facing and boring head set suitable for? The VBHC Facing and Boring Head Set by Vertex is intended for precision facing and internal boring on workpieces within the Ø10–Ø110 mm range, offering stable concentricity and repeatable surface quality. Which spindle or holder mounting is required? The tooling uses an MT‑2 taper mounting, compatible with standard MT‑2 toolholders and tailstock arrangements on small lathes and machining centres. Is the set ready to use on delivery? Yes, the set is supplied complete for immediate installation and adjustment, allowing fast machine integration and reduced setup time. How does the VBHC support production efficiency? By combining a broad diameter range with precision ground components and MT‑2 compatibility, the VBHC set shortens changeover time and improves repeatability, supporting higher first‑pass yields and lower rework rates. Can the set be used for both prototype and small‑batch production? The Vertex VBHC set is designed for flexible use across prototype work and small‑batch production, offering the repeatability and ease of setup required in both scenarios. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Face And Boring Head Set With SK-50 Collet Mount, Complete Range - Vertex
Take advantage of the combination of precision, compatibility with SK-50 tooling and adaptable caliper range Ø10–Ø110 mm for consistent facing and internal boring results. Order the set directly via Metav Werkzeuge or ask for tailored advice from our consultants. VBHC Plan and Boring Head Set (SK-50) by Vertex — compatible with Ø10–Ø110 mm calipers The VBHC plan and boring head set is a compact solution for precision facing and internal boring on lathes and milling machines equipped with SK-50 tooling interfaces. VBHC plan and boring head set for SK-50 Compatible with calipers Ø10–Ø110 mm Complete set for facing and internal boring Robust design by Vertex Consistent machining quality for repeatable results The set delivers stable facing and precise internal boring thanks to its engineering centred on rigidity and alignment. Built to reduce run-out and vibration, this head set improves repeatability across production runs, so setups remain consistent and scrap rates fall. The design supports steady cutting conditions, which benefits both manual and CNC-assisted operations by enabling predictable tool life and finish quality. Straightforward integration and setup with SK-50 interfaces Designed for the common SK-50 collet standard, the set integrates quickly into existing machines used in toolrooms and production shops. Compatibility with calipers from Ø10–Ø110 mm simplifies tool selection for different bore diameters, while the modular nature of the set allows rapid changeover between facing and boring tasks. Clear labelling of the components reduces setup time and helps maintain process control on the shop floor. Built to endure workshop demands Manufactured by Vertex with attention to surface finishes and mechanical tolerances, the set emphasises durability and low maintenance. Core components resist wear under typical cutting loads, supporting a long service life when operated within recommended parameters. The robust construction minimises unplanned downtime and contributes to predictable maintenance cycles, which is essential for efficient production planning. Practical applications that improve throughput This plan and boring head set serves metalworking, die maintenance, and general engineering workshops where accurate bores and faced surfaces are required. By combining planar machining and boring capability in one set, task sequences can be shortened and tool inventory simplified. The result is improved throughput and a clearer process workflow that supports both prototype work and small to medium series production. For tailored technical advice or a precise quotation for SK-50 applications, contact Metav Werkzeuge in Emmerich — reach us at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VBHC-SK50-BC2 GTIN: 4061905093906 eClass: 21041590 Facts Collet type: SK-50 Suitable for calipers: Ø10–Ø110 mm Set: yes Special features Plan and boring head set Designed for facing and internal boring Brand: Vertex FAQ What machine interfaces does the set require? The set is designed for machines using an SK-50 collet interface and can be fitted where that standard is supported. Which bore diameters can be processed with this head set? Processing is suitable for bores within the Ø10–Ø110 mm range when used with the corresponding tooling in the set. Is this product supplied as a complete set? Yes, the VBHC is supplied as a set and includes the components necessary for facing and internal boring operations. Who manufactures the plan and boring head set? The plan and boring head set is produced by Vertex; the item is listed under SKU VBHC-SK50-BC2. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Facing and Boring Head Set BT40, Holder BC2 - Vertex
The compact Vertex VBHC facing and boring head set combines BT‑40 compatibility with a wide bore range and stable construction; ideal for integrating precise internal machining into existing tooling solutions. Benefit from reduced setup time and consistent finish quality — order directly via Metav Werkzeuge or consult our specialists for application advice. VBHC-BT40-BC2 – Vertex facing and boring head set, BT‑40 compatible, Ø10–Ø110 mm The VBHC facing and boring head set for precision internal machining on BT‑40-equipped milling centres and machining centres BT‑40 toolholder compatibility Bore range Ø10–Ø110 mm High rigidity for stable cuts Easy fine adjustment for accuracy Built for consistent, measurable precision The VBHC set is designed to deliver repeatable results across series production and single-part work. With BT‑40 compatibility and a working range of Ø10–Ø110 mm, the kit enables both finishing and sizing of bores with minimal tool changes. The combination of rigid construction and precise adjustment mechanisms reduces vibration and runout, which directly improves surface finish and tolerances for internal machining operations. This reliability supports predictable cycle times and lowers scrap rates. Clear function: what the set performs and why it matters A facing and boring head set performs two core tasks: facing to machine flat surfaces and boring to enlarge and finish internal diameters to the required tolerance. The VBHC uses mechanical fine adjustment to control material removal in small, measurable increments, so operators achieve target diameters without repeated trial cuts. For those less familiar with boring heads, this means fewer measurement cycles and a faster path from setup to finished part, while preserving precision and extending tool life through controlled cutting conditions. Integration into workshop workflows The kit’s BT‑40 interface makes it straightforward to fit the heads into common spindle toolholders, simplifying logistics for shops that standardise on BT‑40 tooling. As a ready set, it reduces the need for multiple single tools and streamlines changeover procedures. The practical result is a lower number of toolholders at the machine and quicker transitions between facing and boring tasks. For production environments and specialist toolrooms alike, this supports higher uptime and a more efficient use of machine capacity. Practical benefits and operational efficiency Beyond diameter control and compatibility, the set emphasises operator efficiency: adjustment elements are accessible and designed for trusted repeatability, so setup times are shorter and measurement routines are simplified. The measurable bore range and compact design contribute to safer handling and storage. When combined with consistent inspection practices, the VBHC head set helps maintain quality targets across batch runs, providing a dependable component for precision machining processes. For BT‑40 machining centres, choose the Vertex VBHC facing and boring head set from Metav Werkzeuge for reliable, measurable precision — contact Metav Werkzeuge’s specialists at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific applications. Technical data SKU: VBHC-BT40-BC2 GTIN: 4061905090554 Brand: Vertex Product type: Facing and boring head set Kit: Set Facts Bore range: Ø10–Ø110 mm Weight: 2.65 kg Toolholder: BT‑40 eCl@ss: 21041590 Special features Designed for facing and boring operations Compact construction for reduced overhang Fine adjustment for diameter control Suitable for integration with BT‑40 tool systems FAQ What bore sizes can be machined with this set? The VBHC facing and boring head set machines bores from Ø10–Ø110 mm, covering common internal diameters for precision finishing. Is the set compatible with my machine’s toolholder system? Compatibility is provided via a BT‑40 interface; the Vertex VBHC set fits BT‑40 toolholders used on many milling centres and machining centres. Does the set include features for fine diameter adjustment? Yes. The Vertex VBHC set includes fine adjustment mechanisms that allow precise, incremental control of the bored diameter for accurate finishing. Can the kit be used for both facing and boring in a single setup? The VBHC set is designed for facing and boring operations and can be integrated into workflows to reduce tool changes, helping to shorten setup times. What is the product identification for ordering or inventory? Order or reference the Vertex facing and boring head set using SKU VBHC-BT40-BC2 and GTIN 4061905090554 for clear identification. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Facing And Boring Head Set With MT3 Collets, 2.5kg - Vertex
Take advantage of the combination of consistent precision, a wide bore range (Ø10–Ø110 mm) and straightforward machine compatibility for reliable finishing and boring operations; order the set directly via Metav Werkzeuge or consult our specialists for tailored guidance. VBHC-MT3-BC2 Planing and Boring Head Set — MT-3 taper, Ø10–Ø110 mm A VBHC-MT3-BC2 planing and boring head set designed for precise facing and internal boring tasks across a broad diameter range, suitable for standard machine spindles. MT-3 taper for common machine spindles Suitable bores Ø10–Ø110 mm Compact set weighing 1.9 kg Precision facing and boring capability Consistent precision for finishing and bore accuracy The facing and boring unit delivers reliable accuracy by covering a broad working range from Ø10–Ø110 mm, which reduces the need for multiple specialised tools. The MT-3 taper provides secure seating in compatible spindles, ensuring stable rotation and concentricity during machining. When finishing internal diameters and faces, the controlled geometry of the toolhead minimises runout and helps maintain repeatable results, so parts meet dimensional tolerances with fewer adjustments. This supports efficient production planning and predictable cycle times. Simple integration with standard machines and quick setup Designed as a compact set, the unit integrates with conventional machine spindles using the MT-3 taper, enabling rapid changeover and minimised setup time. At 1.9 kg, the assembly balances compactness with sufficient mass to dampen minor vibrations without overburdening the spindle. For operators working across small-batch and repair applications, the compatibility with common tapers and the straightforward connection mean reduced tool inventory and faster restoration of machine capability. Clear mechanical interfaces simplify fitting and alignment, even in busy workshop environments. Built for dependable shop-floor performance The set is intended to increase uptime through dependable mechanical behaviour and straightforward functionality. By offering a single tool solution for facing and boring across a wide diameter spectrum, the assembly helps lower process complexity and the frequency of tool changes, positively affecting throughput. Produced under the Vertex umbrella, the unit aligns with expected workshop standards for reliability and repeatability, making it a pragmatic choice for precision-driven tasks that require consistent surface quality and concentricity. Choose the Vertex VBHC-MT3-BC2 for dependable facing and boring performance and contact Metav Werkzeuge to discuss compatibility with existing machines or to arrange a purchase through our European distribution channel. Technical Data SKU: VBHC-MT3-BC2 GTIN: 4061905088971 Brand: Vertex ECLASS: 21041590 Facts Weight: 1.9 kg Suitable bore range: Ø10–Ø110 mm Special features Taper type: MT-3 Delivered as a set Intended for facing and internal boring tasks FAQ Is the VBHC-MT3-BC2 compatible with standard Morse taper spindles? The VBHC-MT3-BC2 is specified with an MT-3 taper and is intended for machines accepting that taper standard, ensuring correct seating and rotational stability. What bore sizes can be machined with this set? The set covers a working range from Ø10 to Ø110 mm, allowing both small and medium internal diameters to be faced or bored with the same assembly. How heavy is the assembly and does that affect spindle balance? The complete assembly weighs 1.9 kg; the mass is designed to provide sufficient damping without adversely affecting spindle balance when installed correctly. Is the VBHC-MT3-BC2 supplied as a single unit or as multiple components? The product is supplied as a set, including the components necessary for facing and boring operations within the stated diameter range. Which applications are best suited to this facing and boring head set? The unit is suited to finishing and internal boring on components requiring consistent concentricity and surface quality, particularly in workshops and small-batch production where tool versatility reduces changeovers. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Facing and Boring Head Set, NT-40 Collet System - Vertex
With NT-40 compatibility, a wide operating range of Ø10–Ø110 mm and a compact 2.8 kg construction, the VBHC face and boring head set improves set-up speed and maintains concentric accuracy in serial and jobbing work. Order the VBHC-NT40-BC2 directly via Metav Werkzeuge or ask our consultants if needed. VBHC face and boring head set — NT-40 interface, Ø10–Ø110 mm, Vertex The VBHC face and boring head set is a precision NT-40 collet-mounted accessory for facing and boring operations, intended for workshop and production environments where flexible diameter control and repeatable accuracy are required. NT-40 collet interface for standard spindles Diameter range Ø10–Ø110 mm compatibility Compact set, total weight 2.8 kg Precision boring and facing capability Faster set-ups through a standardised NT-40 interface Built for machines with the standard NT-40 taper, the head set reduces adapter complexity and shortens changeover times. The collet interface ensures axial rigidity and uniform clamping force, which contributes to improved cycle-time stability and better surface finish. For production-oriented workshops and toolrooms, this results in fewer adjustments and more predictable process control, translating into higher throughput with consistent tolerances. Broad diameter range that reduces tool changes A working span of Ø10–Ø110 mm enables a single toolset to cover multiple bore sizes without repeated retooling. The adjustable boring and facing capability provides gradual diameter increase and fine radial corrections, so fewer toolholders are required on the workbench. This flexibility supports mixed-batch production and short runs by lowering setup overhead while maintaining process reliability and concentricity. Compact, robust construction for reliable precision Weighing approximately 2.8 kg, the set combines a compact footprint with mechanical stability to withstand machining forces during facing and boring cycles. The construction prioritises precision, keeping runout low and allowing tight dimensional control without excessive balancing. The compact design also simplifies storage and transport between machines, making the assembly suitable for both dedicated production lines and versatile job-shop environments. Request the VBHC-NT40-BC2 from Metav Werkzeuge to secure NT-40 compatibility and reliable supply from Emmerich — Metav's consultants can provide technical clarification and delivery details Technical Data Article number: VBHC-NT40-BC2 GTIN: 4061905089435 ECLASS: 21041590 Manufacturer: Vertex Facts Weight: 2.8 kg Diameter range: Ø10–Ø110 mm Collet type: NT-40 Set: yes Special features Face and boring head set Compatible with NT-40 spindles Precision boring and facing Compact, workshop-ready construction FAQ Is the head set compatible with NT-40 spindles? Yes. The VBHC face and boring head set is designed for NT-40 interfaces and fits machines that accept NT-40 tooling. What diameter range can be machined with this set? The VBHC-NT40-BC2 covers a working range from Ø10 to Ø110 mm for both facing and boring tasks. Is the set suitable for production use where repeatability matters? Yes. The combination of a rigid NT-40 collet interface and a compact design delivers consistent concentricity and repeatable bore geometry for serial production. What does the set include? Supplied as a combined facing and boring head set under SKU VBHC-NT40-BC2 for standard NT-40 applications. How heavy is the complete set? Total weight is approximately 2.8 kg, offering a balance between robustness and ease of handling. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø110mm Planar and Boring Head Set R8 Collet, Set - Vertex
The combination of R8 compatibility and a wide working range Ø10–Ø110 mm delivers versatile machining options, while the lightweight 2 kg set eases handling in busy workshops. Benefit from the stable clamping interface and compact design—order the set directly via Metav Werkzeuge or consult the Metav advisors for configuration support. VBHC facing and boring head set — R8 interface, suitable Ø10–Ø110 mm (Vertex) The VBHC is a compact facing and boring head set for milling machines, designed for R8 spindle interfaces and suited to precise bore work across a Ø10–Ø110 mm range. Complete facing and boring head set Designed for R8 spindle interfaces Suitable for bores Ø10–Ø110 mm Lightweight total mass 2 kg Precise machining for varied workshop tasks The set provides a facing and boring solution that balances rigidity with adaptability. Designed to handle a broad diameter range, the tooling enables consistent results when facing surfaces or enlarging bores. The combination of a defined collet interface and carefully engineered geometry reduces runout, which translates into improved surface finish and tighter tolerances. For technicians seeking dependable repeatability, this ensemble supports efficient series work and single-part accuracy alike. Robust clamping and easy compatibility A key advantage is the R8 interface, which ensures secure attachment to common milling spindles and simplifies changeovers. The collet-based mounting offers firm radial support and reduced vibration during cutting, improving tool life and process stability. For users less familiar with the terminology: an R8 collet is a standard spindle tapersystem that provides accurate concentricity and straightforward interchangeability. This results in shorter set-up times and fewer adjustments between operations. Workshop efficiency through compact design Weighing just 2 kg, the set is compact enough for convenient handling and storage while remaining substantial enough to provide steady cutting performance. Delivered as a set, the components are intended to cover typical facing and boring requirements without the need for multiple single-purpose heads. Manufactured by Vertex, the set reflects established production standards and is intended to integrate with existing tooling stocks to streamline workflow and reduce downtime. For tailored advice and reliable supply of the VBHC facing and boring head set, contact Metav Werkzeuge in Emmerich—our specialists will recommend the optimal configuration for R8 spindles and workshop needs. Technical Data Article number: VBHC-R8-BC2 GTIN: 4061905084584 ECLASS: 21041590 Facts Weight: 2 kg Suitable bore range: Ø10–Ø110 mm Special features Collet type: R8 Set: yes Brand: Vertex FAQ What materials can be machined with this facing and boring head set? The VBHC facing and boring head set is intended for general milling and boring tasks; compatibility with specific materials depends on cutter selection and machining parameters rather than the head itself. Is the VBHC compatible with my milling machine spindle? Compatibility is ensured where an R8 spindle interface is present; the set is designed for machines accepting R8 collets and tapers. How precise is the concentricity provided by the set? The VBHC-R8-BC2 is engineered for stable clamping to minimise runout, supporting improved concentricity and consistent surface finish during facing and boring operations. Does the set include collets or additional adapters? The delivery comprises the facing and boring head set configured for R8 mounting; specifics on included accessories should be confirmed with Metav Werkzeuge if additional adapters are required. Can this set speed up setup and changeover times? Yes, the compact set format and standard R8 interface reduce changeover complexity, leading to shorter set-up times in mixed-production environments. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Face and Boring Head Set BT40, Tool Holder Set - Vertex
Benefit from the combination of reliable BT‑40 mounting, a wide machining range and solid construction to maintain consistent cycle times and reduced rework. Order the VBHC facing and boring head set directly via Metav Werkzeuge or ask our consultants if needed. VBHC facing and boring head set — BT‑40, Ø10–Ø220 mm The VBHC facing and boring head set is a modular machining head for precision facing and internal boring across a broad diameter range on BT‑40 spindles. BT‑40 taper for secure spindle mounting Diameter range Ø10–Ø220 mm for versatility Precise adjustment for repeatable bore sizes Robust 4.7 kg construction for stable cutting Secure mounting that reduces setup time A BT‑40 spindle interface delivers secure mounting and fast machine changeovers, letting workshops keep spindle runout and concentricity within tighter tolerances. The BT‑40 connection is an industry standard on many milling centres and machining centres, which means straightforward integration without special adaptors. With the head’s solid construction and repeatable seating, setup times are reduced and machine uptime improves, supporting predictable production cycles and more efficient scheduling. Broad diameter coverage for fewer tool changes The head set’s Ø10–Ø220 mm working range enables processing of small to large bores without frequent tool swaps, decreasing downtime and handling. For mixed-batch work or toolrooms that deal with varied part sizes, this breadth translates into simpler tooling strategies and fewer changeover errors. The modular nature of the set permits adjustment across the range while maintaining cutting geometry, so workshops can plan jobs more effectively and achieve consistent outcomes across a wider scope of components. Fine adjustment for consistent quality and lower scrap rates The adjustment mechanism is engineered to facilitate precision in bore diameter and face finishing, improving repeatability from part to part. By enabling small, controlled corrections, the head set helps maintain intended tolerances and surface quality, which reduces the need for secondary operations or rework. For applications where dimensional accuracy is critical, this level of control supports predictable first-pass yields and an overall reduction in production costs related to correction and inspection. Stable build for dependable industrial performance Weighing 4.7 kg, the assembly provides the mass and rigidity needed to resist vibration during heavy cuts, contributing to improved surface finish and tool life. The set is supplied as a complete unit for facing and boring tasks, designed for robust shop-floor use and repetitive cycles. Its construction supports stable cutting conditions that are essential for long machining campaigns, offering a balance between durability and the fine control required for precision internal machining. For reliable BT‑40 compatibility and broad Ø10–Ø220 mm capacity, contact Metav Werkzeuge in Emmerich for a tailored technical quote and delivery of the Vertex VBHC facing and boring head set Technical Data SKU: VBHC-BT40-BC3 GTIN: 4061905089121 Manufacturer: Vertex ECLASS: 21041590 Core specifications Weight: 4.7 kg Collet type: BT‑40 Diameter range: Ø10–Ø220 mm Set: yes Special features Designed for facing and internal boring Modular head set Suitable for a wide range of workpiece diameters Robust construction for stable machining FAQ Which spindle taper is required for this head set? The VBHC facing and boring head set requires a BT‑40 spindle taper; the VBHC‑BT40‑BC3 configuration is made for machines with a BT‑40 interface. What diameter range can be machined with the set? The set covers Ø10–Ø220 mm, enabling facing and internal boring across small and medium diameters without frequent tool changes. Is the product supplied as a complete set? Yes, the item is supplied as a set; the VBHC facing and boring head set includes the modular components required for facing and boring operations. How does the head set help with achieving repeatable bore sizes? The adjustment mechanism provides fine, controllable changes to bore diameter, improving precision and repeatability, which reduces rework and scrap. How does the weight influence machining performance? At 4.7 kg the head set offers the rigidity needed to resist vibration, supporting stable cutting conditions and better surface finish during repetitive operations. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Face And Boring Head Set With MT4 Collet Mount, Set - Vertex
Take advantage of the combination of high-precision finishing, a wide working range and the quick-change MT-4 clamping system for reliable, repeatable machining. Order the set directly via Metav Werkzeuge or consult our specialists for integration advice. Vertex VBHC Facing and Boring Head Set — MT-4 Collet, Ø10–Ø220 mm range The VBHC facing and boring head set is designed to deliver precise internal and face machining across a broad diameter range, ideal for finishing operations in small to medium workshops and toolrooms MT-4 collet system for secure clamping Suitable for Ø10–Ø220 mm operations Compact, robust 4.3 kg construction Delivered as a complete set Accurate finishing with minimal adjustment The set delivers consistent precision for finishing applications by combining a rigid head design with the established MT-4 clamping interface. With a working span from Ø10–Ø220 mm, the assembly reduces the need for multiple specialised tools and enables repeatable results across different job runs. The design focuses on direct benefits for production: fewer setups, lower scrap rates and improved part conformity to tolerances. Where surface quality matters, the head’s construction supports fine feed control and steady cutter engagement for a measurable improvement in finish. Modular configuration that speeds up workflow A modular arrangement allows quick changes between facing and boring functions without complex retooling. The set format brings together components that are matched to one another, shortening setup time and simplifying tool inventory management. For machinists unfamiliar with the specific terms: a facing head machines flat surfaces perpendicular to the spindle axis, while a boring head enlarges or finishes internal diameters—both tasks that benefit from the coordinated adjustments provided by a purpose-built set. This practicality translates into more productive hours on the machine and reduced downtime. Rigidity and balance for improved surface quality Weighing in at 4.3 kg, the assembly provides inherent mass that helps dampen vibration during cutting. Increased stability directly contributes to a better surface finish and extended cutter life, particularly when working at higher feeds or with tougher materials. The balanced construction reduces chatter and improves dimensional control, which in turn supports tighter tolerances and fewer secondary operations. In short, the combined effect is higher throughput with consistent quality — a rational advantage for any production environment. Broad compatibility for diverse workshop tasks Built for integration with MT-4 taper toolholders and spindle setups, the set suits a wide variety of finishing jobs without the complexity of custom fixtures. The Vertex engineering approach ensures the components fit into existing workflows while offering the adaptability required for mixed-batch production. The complete configuration is well suited to toolrooms, maintenance departments and small-scale manufacturing where flexibility and precision must coexist without large investments in special-purpose equipment. For personalised technical advice on the Vertex VBHC facing and boring head set and to arrange procurement through Metav Werkzeuge in Emmerich, contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VBHC-MT4-BC3 GTIN: 4061905094217 Manufacturer: Vertex Facts Weight: 4.3 kg Suitable diameter range: Ø10–Ø220 mm Collet type: MT-4 eClass: 21041590 Special features Set configuration SKU: VBHC-MT4-BC3 Gallery images available FAQ What diameter range can be finished with this head set? The VBHC facing and boring head set supports operations across a Ø10–Ø220 mm range, suitable for both small and larger internal bores and facing tasks. Which collet system is required for mounting? The set is designed for the MT-4 collet interface and is compatible with MT-4 toolholders and spindles. Is the set supplied complete for immediate use? The delivery is a complete set configuration (SKU VBHC-MT4-BC3) intended to simplify initial integration and reduce the need for additional matching components. How does the weight affect machining performance? At 4.3 kg, the assembly improves stability and dampens vibration, which helps achieve better surface finish and dimensional repeatability during finishing cuts. Can this set be used for both facing and boring on one machine? Yes, the modular nature of the set allows both facing and boring operations to be carried out on compatible machines without extensive retooling. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Face and Boring Head Set, NT-50 Collet System, 3-Point Balance - Vertex
Benefit from the combination of NT-50 collet compatibility, a wide working range of Ø10–Ø220 mm and a compact 6.9 kg design to maintain steady facing and boring operations. Order the VBHC facing and boring head set directly via Metav Werkzeuge or ask our consultants if needed. VBHC – Facing and Boring Head Set (NT-50, Ø10–Ø220 mm) by Vertex The VBHC is a facing and boring head set engineered for precision metalworking, providing stable clamping for medium‑range diameters and compatible with NT‑50 collet systems for straightforward integration into workshop tooling. NT-50 collet interface Suitable for Ø10–Ø220 mm Delivered as complete set Robust 6.9 kg construction High-precision control for facing and bore finishing The head set delivers focused support for accurate facing and finishing operations through a dedicated NT-50 collet interface and a broad usable diameter band of Ø10–Ø220 mm. These characteristics translate into consistent concentricity and reproducible bores when used for finish machining or corrective facing, reducing the need for rework. The configuration is particularly suitable where stable clamping and minimal runout are required, and the specification is easy to check against inspection equipment to ensure process compliance. Faster setup and reliable repeatability in production Delivered as a complete set, the tooling bundle reduces procurement complexity and simplifies changeovers on lathes or machining centres equipped for NT‑50 tooling. The unit’s 6.9 kg mass contributes to stability during cutting, which supports repeatable surface quality over multiple cycles. By standardising on a single collet interface and a clearly defined diameter range, workshop planners achieve better tool allocation and shorter downtime between jobs, improving throughput without compromising finish. Durable, workshop-ready design for consistent results Built under the Vertex brand, the head set emphasises durability and suitability for routine workshop use. The structural balance between manageable mass and mechanical robustness offers a dependable solution across a range of facing and boring tasks, helping to maintain tool life and steady performance. Where traceability is important, the set is identified by SKU VBHC-NT50-BC3, enabling straightforward inventory control and integration into existing tooling registries. Discuss the integration of the Vertex VBHC head set with Metav Werkzeuge for application advice and reliable supply from Emmerich – contact Metav Werkzeuge by e‑mail or phone to clarify fitment and delivery options. Technical data Article number: VBHC-NT50-BC3 GTIN: 4061905088988 Manufacturer: Vertex Core technical data Weight: 6.9 kg Suitable diameter range: Ø10–Ø220 mm ECLASS: 21041590 Special features Product type: Facing and boring head set Collet interface: NT-50 Delivered as set (satz: true) FAQ What diameter range is covered by the head set? The VBHC facing and boring head set supports diameters from Ø10 to Ø220 mm, making it suitable for a wide range of medium-size bores and facing operations. Which collet interface does the set use and why does it matter? The tooling uses the NT‑50 collet interface; this ensures compatibility with machines and accessories designed for NT‑50 tooling and provides stable clamping for improved concentricity. Is the VBHC suitable for production environments with frequent changeovers? Yes, the VBHC is supplied as a complete set, which simplifies tooling management and shortens setup times, supporting efficient changeovers in production runs. How is the product identified for inventory and ordering? The set is listed under SKU VBHC-NT50-BC3 and GTIN 4061905088988, which can be used for procurement and stock tracking. Which manufacturer produces this head set? The head set is produced by Vertex and supplied with the attributes and identification detailed above for traceability and quality assurance. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Face and Boring Head Set, NT30 Collet, Set - Vertex
Take advantage of a compact facing and boring head set that combines an NT-30 collet interface with an adjustable diameter range of Ø10–Ø220 mm for consistent, repeatable results in small-batch and job-shop production. Order the set directly via Metav Werkzeuge or consult the Metav team for application advice and supply from Emmerich. VBHC facing and boring head set with NT-30 interface, adjustable Ø10–Ø220 mm — Vertex The VBHC is a facing and boring head set designed for precision finishing and internal machining on milling machines and machining centres, providing a flexible solution where concentricity and repeatability matter. Adjustable Ø10–Ø220 mm range NT-30 collet interface Set for facing and boring operations Compact 4.1 kg set weight Maintain process accuracy with a proven collet interface The use of an NT-30 collet interface in this assembly ensures a secure mechanical connection to compatible spindles, which improves concentricity and reduces runout during facing and boring operations. By relying on a standardised interface, the tooling set supports repeatable tool positioning and simplifies changeovers on machining centres that accept NT-30 tooling. The clear mechanical advantage is a reduction in rework and faster set-up times, translating into higher throughput for short production runs. Flexible diameter coverage reduces tooling inventory With an adjustable working range from Ø10–Ø220 mm, the kit covers a broad spectrum of internal diameters without the need to purchase multiple dedicated heads. This flexibility allows a workshop to respond to varied component geometries while keeping tool inventory lean. The configuration suits both roughing to establish bore geometry and finishing passes where tool stability and fine adjustment directly contribute to a consistent surface finish and dimensional compliance. Built for rapid changeovers and dependable repeatability The set format is engineered to speed routine operations: modular components and the NT-30 interface allow swift attachment and detachment, limiting machine downtime between jobs. The overall assembly mass of 4.1 kg balances rigidity with manageability, offering a stable platform that resists chatter while remaining straightforward to handle during tool changes. Improved repeatability lowers inspection workload and helps maintain steady production quality across batches. Workshop-ready supply from a precision-focused partner Sourced from Vertex and distributed through Metav Werkzeuge, this facing and boring head set is intended for workshops and specialist engineering shops that demand reliable, versatile tooling. Metav’s role as a “quality filter” for the European market supports consistent product availability and pragmatic delivery from Emmerich, backed by decades of metrology and tooling expertise. The combination of adaptable tooling and a dependable supply chain reduces procurement friction and supports predictable machine shop planning. Choose the Vertex VBHC facing and boring head set for resilient, repeatable machining — contact Metav Werkzeuge for tailored advice and fast supply from Emmerich (info@metav-werkzeuge.com • +49 2822 7131930) Technical Data SKU: VBHC-NT30-BC3 GTIN: 4061905094224 Manufacturer: Vertex Core specifications Weight: 4.1 kg Diameter range: Ø10–Ø220 mm eClass: 21041590 Design & features NT-30 collet interface Set configuration for facing and boring Compact, workshop-suitable assembly FAQ What spindle interfaces are compatible with this facing and boring head set? The set uses an NT-30 collet interface; compatibility requires a spindle or adapter accepting NT-30 tooling to ensure correct mounting and performance. Which diameter range can be machined with the set? The tooling set accommodates bores from Ø10–Ø220 mm, covering common internal diameters for finishing and semi-finish operations. Is this assembly suitable for production use on a machining centre? Yes. The construction and NT-30 interface make the set suitable for machining centres where consistent concentricity and repeatability are required. How heavy is the complete set and what does that imply for handling? The complete set weighs 4.1 kg, offering a balance between rigidity for stable cutting and manageable handling during tool changes. Who supplies this facing and boring head set in Europe? The set is supplied by Metav Werkzeuge and originates from Vertex, offering workshop-focused availability and supply continuity. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Facing and Boring Head Set BT30, Collet Chuck BC3 Compatible - Vertex
Take advantage of the combination of rigid BT‑30 clamping, a broad Ø10–Ø220 mm working range and a ready-to-fit set for faster changeovers — the result is reliable shop performance and consistent bore quality. Order the set directly via Metav Werkzeuge or consult the team for application advice. VBHC Facing and Boring Head Set (BT‑30) — Ø10–Ø220 mm capacity A VBHC facing and boring head set designed for precision CNC machining and metalworking, compatible with BT‑30 spindles and intended for operations in the Ø10–Ø220 mm range. BT‑30 compatibility for secure spindle clamping Capacity Ø10–Ø220 mm for versatile boring Precision-ground components for accurate results Complete set, ready for workshop integration Firm clamping and repeatable accuracy for serial work The modular head is engineered for consistent precision across repetitive operations. With a BT‑30 collet interface the assembly offers robust spindle-to-tool connection, reducing runout and vibration during cutting. Reduced vibration improves surface finish and extends cutter life, which directly lowers per-part cost in production runs. The compact mass, at 4.34 kg, provides a balance between rigidity and manageable handling during tool changes, helping machine shops maintain tight tolerances without additional fixturing. Broad bore capacity that reduces setup complexity A wide working range of Ø10–Ø220 mm enables both small-diameter finishing and larger reaming or boring tasks without frequent tooling swaps. The configuration of the set simplifies setup: successive operations can be completed with the same centring and alignment, cutting non-productive time. For manufacturers processing mixed batches or prototypes, this flexible capacity shortens throughput times while maintaining geometric accuracy, so fewer tool assemblies are required across varied component families. Designed to keep the machining centre productive The set contains precision-ground components that are matched for concentricity and balance, which contributes to stable cutting conditions and predictable tool life. Balanced assemblies reduce spindle wear and allow for more aggressive feeds when appropriate, translating into improved cycle times. Supplied as a coordinated kit, the product supports organised tooling management in the workshop and reduces the likelihood of mismatched accessories that can cause scrap or rework. Practical applications and maintenance guidance Intended for facing, boring and fine finishing in general metalworking and CNC environments, the set is suitable where structural rigidity and accurate bore geometry are required. Compatibility with standard BT‑30 taper spindles ensures straightforward installation on many machining centres. Routine checks of clamping surfaces and periodic rebalancing after heavy use keep the unit performing reliably. The manufacturer's design focuses on longevity and serviceability, which supports predictable production planning. Contact Metav Werkzeuge for tailored advice on integrating the Vertex VBHC facing and boring head set into existing machine fleets and to arrange supply from our Emmerich stock. Technical data Article number: VBHC-BT30-BC3 GTIN: 4061905088889 Manufacturer: Vertex Weight: 4.34 kg Set: Yes Core specifications Collet type: BT‑30 Working range: Ø10–Ø220 mm ECLASS: 21041590 SKU: VBHC-BT30-BC3 Special features Precision-ground components Workshop-ready kit Compatible with BT‑30 spindles Designed for facing and boring FAQ What machines is this set compatible with? The set is intended for machining centres with a BT‑30 taper; the Vertex VBHC facing and boring head set (SKU VBHC-BT30-BC3) fits standard BT‑30 spindle interfaces found on many CNC machines. Which bore diameters can be produced with the set? The kit covers a working range of Ø10–Ø220 mm, enabling finishing and reaming across a broad diameter spectrum without frequent tooling swaps when using the VBHC set. Does the set include all accessories for immediate use? Yes, the VBHC set is supplied as a ready-to-fit kit containing the matched components required for standard facing and boring tasks, designed to simplify workshop integration. How should the equipment be maintained to preserve accuracy? Regular inspection of clamping faces and periodic rebalancing are recommended to maintain concentricity and performance of the Vertex VBHC facing and boring head set; follow the machine tool manufacturer's maintenance intervals for the spindle interface. Is the set suitable for high-volume production? The precision-ground and balanced nature of the components makes the VBHC set appropriate for serial production where repeatable bore quality and reduced cycle times are priorities. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Facing and Boring Head Set R8, Complete Tooling - Vertex
Benefit from precise facing and internal boring with the R8 collet interface and compatibility across Ø10–Ø220 mm, plus a robust workshop weight of 4.2 kg for reliable repeatability; order the VBHC-R8-BC3 directly via Metav Werkzeuge or ask the consultants if needed. VBHC-R8-BC3 Plan and Boring Head Set — R8 collet, Ø10–Ø220 mm — Vertex The VBHC-R8-BC3 is a facing and boring head set engineered for milling applications where accurate face finishing and controlled internal boring are required, compatible with machines using an R8 collet interface. R8 collet interface Compatible with Ø10–Ø220 mm Delivered as a complete set Precise machining where repeatability matters The set is designed to deliver consistent results for facing and internal boring operations, making it suitable for small to medium workshop series. The R8 collet connection provides widely used machine compatibility and a secure spindle interface, while the defined Ø10–Ø220 mm range clarifies the working scope. These measurable parameters support reliable process planning and make tool selection straightforward for production environments focused on tolerances and surface finish. Faster set-up and dependable clamping Quick clamping and predictable alignment reduce machine downtime. The integrated collet interface and the set format minimise the number of tool changes required at the machine, translating into shorter set-up times and more productive spindle hours. The compact mass, of approximately 4.2 kg, balances stability during cutting with manageable handling in the workshop, aiding both manual set-up and automated tool changes. Robust design for everyday workshop use Constructed for routine industrial use, the set combines facing and boring functions in a single kit, helping to streamline the tooling inventory. Sturdy construction supports consistent concentricity and helps to maintain cutting geometry under normal loading. Clear, measurable specifications make it straightforward to plan maintenance intervals and replacement parts, supporting predictable tool life and operational continuity. Contact Metav Werkzeuge for tailored advice on the Vertex VBHC facing and boring head set — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility with specific machines or applications Technical Data Article number: VBHC-R8-BC3 GTIN: 4061905092954 Manufacturer: Vertex Facts Weight: 4.2 kg Collet type: R8 Suitable diameters: Ø10–Ø220 mm Special features Delivered as set Facing and boring head functions SKU: VBHC-R8-BC3 FAQ What operations is this set designed for? The VBHC-R8-BC3 set is intended for precision facing and internal boring operations typically performed on milling machines using an R8 collet interface. Which machines is the set compatible with? Compatibility is determined by the toolholder; the set uses an R8 collet interface and therefore fits machines accepting R8 tooling. What is the supported workpiece diameter range? The kit is specified for workpiece diameters in the range Ø10–Ø220 mm, which defines its practical application envelope. Is this delivered as a single package or separate items? The VBHC-R8-BC3 is supplied as a complete set, combining facing and boring head functions for streamlined tooling. How heavy is the set and what does that mean for handling? Weighing 4.2 kg, the set balances robustness and portability, facilitating safe manual handling and stable performance in the spindle. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Facing and Boring Head Set, BT-50 Collets, 7.7kg - Vertex
Take advantage of the combination of repeatable accuracy, BT-50 compatibility and a wide working range for efficient facing and boring operations; the set’s robust construction ensures stable results and low downtime. Order the VBHC facing and boring head set directly via Metav Werkzeuge or contact our consultants for tailored advice. VBHC Facing and Boring Head Set — BT-50 Interface, Ø10–Ø220 mm A VBHC facing and boring head set designed for precise external facing and internal boring on machines with a BT-50 spindle taper, covering a diameter range of Ø10–Ø220 mm. Precision facing and boring capability Compatible with BT-50 spindle systems Suitable for diameters Ø10–Ø220 mm Robust build; total weight 7.7 kg Engineered for repeatable precision and stable results The facing and boring head set is engineered to deliver consistent machining accuracy, reducing the need for rework. With a rigid BT-50 connection and a balanced design, the assembly minimises runout and vibration that can compromise surface finish. For production environments where component tolerances must be upheld across batches, the set provides a measurable improvement in repeatability; the reduced vibration translates into better tool life and fewer rejects, supporting lean workflows and predictable cycle times. Wide diameter range for flexible workshop use Covering a working span of Ø10–Ø220 mm, the head set simplifies changeovers between small-diameter and larger components without swapping core tooling. This versatility is particularly useful in small-series production and repair shops where one setup must handle diverse parts. The diameter range is presented as an objective specification to help plan operations and tooling strategies: it enables fewer toolholders to be kept in inventory and reduces machine downtime during part changeover, contributing to operational efficiency. Built for durability and straightforward maintenance Constructed as a complete set, the assembly’s robust build and balanced mass (7.7 kg total) support stable cutting conditions under typical workshop loads. The design focuses on accessibility for routine checks and replacement of wear parts, keeping service intervals predictable and maintenance effort low. As a Vertex-supplied solution, the set aligns with professional expectations for long-term performance, making it a pragmatic choice for workshops seeking dependable tooling that integrates with existing BT-50 tooling systems. For professional facing and boring tasks, contact Metav Werkzeuge for the Vertex VBHC set and expert advice — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application fit and delivery from our Emmerich quality hub. Technical data Article number: VBHC-BT50-BC3 GTIN: 4061905089442 Manufacturer: Vertex Facts Weight: 7.7 kg Diameter range: Ø10–Ø220 mm eClass: 21041590 Special features BT-50 spindle taper interface Set configuration SKU: VBHC-BT50-BC3 FAQ What machining tasks is this set intended for? The VBHC facing and boring head set is designed for precise external facing and internal boring operations on machines equipped with a BT-50 taper. Which spindle interface does the set use? This head set uses the BT-50 spindle taper, enabling direct mounting on compatible lathes and milling heads. What diameter range does the assembly cover? The assembly supports a working diameter range of Ø10–Ø220 mm, allowing flexible use across small and medium-sized components. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Facing and Boring Head Set, MT2 Collet Adapter - Vertex
Combine versatile facing and accurate boring capability with MT‑2 collet compatibility to streamline setup and expand machining range. The compact construction and wide Ø10–Ø220 mm capacity make this set suitable for diverse workshop tasks. Order the set directly via Metav Werkzeuge or consult our specialists for integration advice. VBHC-MT2-BC3 Facing and boring head set with MT‑2 collets by Vertex A versatile VBHC-MT2-BC3 facing and boring head set for turning applications, engineered to handle workpiece diameters from Ø10–Ø220 mm with MT‑2 collet compatibility Facing and boring head combination Suitable for diameters Ø10–Ø220 mm MT‑2 collet interface for standard tooling Compact set weight approx 4 kg Accurate faces and bores with reduced setup time The facing and boring combination delivers precision where flat faces and concentric bores are required in one operation. By combining both functions in a single assembly, the setup time is reduced and alignment steps are simplified, which supports more consistent cycle times on the shop floor. The Ø10–Ø220 mm capacity covers small to medium workpieces commonly encountered in general engineering and small-batch production, providing flexibility without constant tool changes. Compact design that fits tight workspaces and tool cabinets A balanced, compact construction allows secure mounting and stable machining while occupying minimal bench or turret space. The MT‑2 collet interface (Morse taper 2) provides compatibility with standard collet tooling and simple replacement, making maintenance straightforward. At approximately 4 kg, the complete set is easy to handle during setup and storage, enabling quicker changeovers and less physical strain for operators. Smooth integration into production workflows and measurable efficiency gains Delivered as a complete set, the assembly reduces procurement complexity and ensures component compatibility from the outset. The combined tool head supports lean machining by lowering fixture complexity and minimising tool inventory. For operations focused on throughput and repeatability, the set contributes to predictable process times and fewer interruptions for tooling swaps. Backed by Vertex engineering, this solution is suited to shops aiming for dependable, long‑term performance. Contact Metav Werkzeuge in Emmerich for expert advice on integrating the Vertex VBHC‑MT2‑BC3 set into your production line and to confirm delivery options Technical Data SKU: VBHC-MT2-BC3 GTIN: 4061905092862 Brand: Vertex Product: Facing and boring head set Core data Suitable diameters: Ø10–Ø220 mm Weight: 4 kg Collet type: MT‑2 Set: Yes Special features Facing function included Boring head function included MT‑2 collet interface Delivered as a matched set FAQ What machining tasks is this set designed for? The VBHC‑MT2‑BC3 by Vertex is designed for facing and boring operations on turning equipment, allowing flat face production and precision bores within the Ø10–Ø220 mm range. Which collets are required for mounting? This set uses an MT‑2 collet interface (Morse taper 2); compatible collets with an MT‑2 shank are suitable for use with the Vertex set. Can the set be used for both small and medium workpieces? Yes. The VBHC‑MT2‑BC3 supports diameters from Ø10 to Ø220 mm, covering a broad spectrum of small to medium parts common in workshops and light industrial manufacture. Is the set supplied as a complete kit for immediate use? The product is delivered as a matched set, which simplifies initial assembly and ensures component compatibility for facing and boring tasks under Vertex specifications. How does this set improve workshop efficiency? By combining facing and boring capabilities in a compact assembly, the set reduces tooling changes and setup time, contributing to steadier cycle times and higher process reliability. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Ø10-Ø220mm Facing and Boring Head Set, MT‑3 Collet Mount - Vertex
The combination of versatile diameter coverage and a secure MT-3 collet interface ensures reliable facing and boring operations in small and mid-sized workshops; the set's compact 4 kg construction simplifies handling and storage. Order the VBHC face and boring head set directly via Metav Werkzeuge or contact the consultants for tailored advice. VBHC face and boring head set — MT-3 collet interface, Ø10–Ø220 mm The VBHC set provides precision facing and internal turning capability for workshop lathes and machining centres, compatible with MT-3 collets and suited for calipers from Ø10 to Ø220 mm. Precision facing and boring set MT-3 collet interface Suitable for Ø10–Ø220 mm Compact set weight: 4 kg Repeatable precision and faster set-up for turning tasks The face and boring head set is engineered to deliver precision where repeatability matters most. With a secure MT-3 collet interface the tooling maintains concentricity during facing and internal turning, reducing rework and scrap. The modular design of the set allows quick changes between operations, which shortens machine downtime and improves throughput. This results in a measurable efficiency gain for shops that run mixed small-batch production or prototyping work. Broad diameter compatibility supports versatile workshop use Covering a measurement window of Ø10–Ø220 mm, the set adapts to a wide range of component sizes without complex retooling. The delivered configuration as a set bundles the essential components for immediate use and simplifies inventory management. At approximately 4 kg, the assembled kit remains portable enough for bench handling while offering the rigidity required for stable metal cutting operations. Where colleagues require a reliable solution for both facing and internal boring, this kit bridges flexibility and robustness. Engineered for professional integration and reliable supply Built by Vertex, the tooling is designed for integration into standard lathe spindles that accept MT-3 mountings and for workflows that demand consistent results. Procurement through Metav Werkzeuge adds a layer of quality assurance: Metav acts as a European "quality filter" with over 48,000 customers and a comprehensive catalogue, ensuring dependable supply and informed product selection. The combination of manufacturer competence and distributor reliability underpins long-term productivity in industrial and specialist workshops. Contact Metav Werkzeuge in Emmerich for technical guidance or to request the Vertex VBHC face and boring head set directly — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Technical Data Article number: VBHC-MT3-BC3 GTIN: 4061905094200 Brand: Vertex Weight: 4 kg Facts Diameter range: Ø10–Ø220 mm ECLASS: 21041590 Special features Collet type: MT-3 Supplied as set SKU: VBHC-MT3-BC3 FAQ What diameter range is supported by the set? The set supports a diameter range of Ø10–Ø220 mm, as specified for the VBHC face and boring head set. Which collet interface is required for mounting? The tooling uses an MT-3 collet interface; the VBHC set is supplied to fit MT-3 spindles and collets. Is the VBHC suitable for both facing and internal boring? Yes, the VBHC face and boring head set is designed for both facing operations and internal turning tasks. What is the total weight of the complete set? The complete VBHC set has a total weight of 4 kg, facilitating bench handling and storage. Can the VBHC set be integrated into standard workshop lathes? The VBHC set is manufactured by Vertex for integration on machines accepting MT-3 mountings and standard workshop setups. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Precision boring heads and taper adaptors for milling operations
Boring heads and taper adaptors are essential components for producing precise, round bores on conventional milling machines. The two product groups are related but distinct: boring heads deliver adjustable, high-precision internal diameters, while taper adaptors provide the correct machine interface and secure tool holding.
How they work in typical workshop and production settings
Boring heads are mounted on milling spindles and adjusted to cut exact diameters, enabling bores with defined fits to be produced on standard machine tools. Taper adaptors ensure compatibility with the machine taper and maintain concentricity under load. For larger diameters, boring bars are fitted into the boring head, allowing stepwise or single-pass enlargement while preserving roundness and surface quality.
Tangible benefits for daily machining
- Increased hole accuracy and repeatability through fine adjustment of boring heads
- Capability to produce large-diameter bores on conventional milling machines, reducing the need for specialised equipment
- Flexible setup: boring heads accept interchangeable boring bars for different diameters and tasks
- Reduced rework and improved fit quality when mating components are required
- Simple integration with standard machine tapers via taper adaptors, improving changeover speed
Why Metav is the pragmatic choice for procurement
Metav positions itself as a precision partner for industry and workshops, combining decades of competence with a broad range of products. From the central hub in Emmerich, Metav offers a curated selection that acts as a quality filter for the European market, supported by more than 48,000 customers and an assortment of over 250,000 products. That combination makes Metav a practical source when standard-compliant boring heads and taper adaptors are required quickly and reliably.
technical data (key points)
- designed for use on milling machines
- produces precise, round bores with defined fits
- suitable for conventional machine tools to create bores with large diameters
- accepts appropriate boring bars depending on application
- taper adaptors provide machine taper interface and toolholding accuracy
Essential takeaway
Boring heads and taper adaptors together enable conventional milling machines to produce accurate, fit-quality bores and handle large diameters with flexibility and repeatability. Metav supplies a broad, quality-filtered range to simplify sourcing and reduce procurement complexity.
FAQ
What are boring heads and taper adaptors used for?
Boring heads are used to produce adjustable, accurate internal diameters; taper adaptors provide the matching machine taper and secure mounting for the boring head.
Can boring heads create large-diameter bores on a milling machine?
Yes—boring heads are designed to enlarge holes to larger diameters on conventional milling machines, often by fitting longer or larger boring bars into the head.
How are boring bars fitted into a boring head?
Depending on the application, appropriate boring bars are inserted into the boring head and secured; this modular approach allows quick changeover between diameters and tool types.
Do taper adaptors affect concentricity and runout?
Properly selected taper adaptors ensure correct machine interface and help maintain concentricity and low runout for the boring head during machining.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com