CNMG 120404 KT315 Indexable Insert - Kennametal

Benefit from a rigid, left-hand PCLN boring bar that accepts CNMG 1204 inserts and delivers stable cutting thanks to a 40 mm shank and 300 mm overall length; order directly via Metav Werkzeuge or consult the Metav team for application advice. Boring bar PCLN for CNMG Indexable Inserts (S40T PCLNL) — left-hand, Ø50 mm A robust PCLN for CNMG Indexable Inserts boring bar designed for external turning where left-hand cutting and reliable insert clamping are required. Left-hand cutting direction Accepts CNMG 1204 inserts Shaft Ø40 mm for stable clamping No internal coolant — external use Engineered for rigidity and consistent chip control The bar’s shaft Ø40 mm and overall length 300 mm provide a stiff toolholder that reduces vibration and improves surface finish. With a cutting height of 55 mm and a mass of 1.825 kg, the assembly maintains cutting stability even under intermittent loads. For production environments this means fewer rejects and more predictable tool life, as the toolholder geometry minimises deflection and supports consistent chip evacuation when paired with the correct CNMG insert geometry. Insert compatibility and cutting geometry for efficient turning Designed specifically for CNMG 1204 indexable inserts, the tool uses a standard insert form that is widely available and economical to replace. The tool’s cutting angle 95° and ISO designation S40T PCLNL ensure correct seating and orientation of the carbide insert, delivering repeatable cutting geometry. This alignment simplifies setup on lathes and reduces indexing time, helping to keep cycle times predictable while maintaining the required dimensional tolerances. Coolant-free design for straightforward maintenance The boring bar is supplied without internal coolant, which removes internal channels and simplifies cleaning and inspection. For operations that use external coolant or dry machining, this reduces potential clogging points and eases maintenance routines. The absence of internal coolant also means fewer sealing elements to monitor, making the tool a practical choice for shops that prefer external coolant application or dry-turning strategies. Integration and procurement for production workflows The tool is identified by SKU P354TM and the ISO code S40T PCLNL, easing part-number management and reordering across procurement systems. As a left-hand tool intended for external turning, it integrates with standard clamping systems that accept a shaft Ø40 mm. Technical documentation and dimensions are straightforward to verify during tool setup, which supports consistent machine-to-machine interchangeability and simplifies tool crib inventory management. Contact Metav Werkzeuge today for tailored advice on Teknik Cutting Tools boring bars—quote SKU P354TM for application recommendations and procurement assistance Technical data SKU: P354TM Manufacturer: Teknik Makina ISO designation: S40T PCLNL Type: PCLN for CNMG Indexable Inserts Cutting direction: left Special feature: without Coolant Measurements Diameter: 50 mm Shank diameter: 40 mm Cutting height: 55 mm Overall length: 300 mm Weight: 1.825 kg Cutting angle: 95° Features / Compatibility For CNMG 1204 inserts Left-hand toolholder No internal coolant (external use) ISO-compatible toolholder form FAQ Which inserts fit this boring bar? The boring bar accepts CNMG 1204 indexable inserts; compatibility is ensured by the PCLN pocket and ISO designation S40T PCLNL used on the Teknik Cutting Tools bar (SKU P354TM). Is the bar suitable for internal coolant? No, the tool is supplied without internal coolant and is intended for external coolant application or dry machining as specified for this left‑hand boring bar. What are the critical dimensions for setup? Key setup dimensions include shaft Ø40 mm, overall length 300 mm, cutting height 55 mm and tool diameter 50 mm; these values support stable clamping and correct insert positioning. Can this bar be used for roughing and finishing? The robust shank and insert compatibility make the bar suitable for both roughing and finishing operations when paired with the appropriate CNMG grade and cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust rigidity, a 32 mm shank and a 300 mm reach for reliable left-hand turning operations; order directly via Metav Werkzeuge or contact our advisors for application-specific guidance. S32T PCLNL Boring Bar – PCLN for CNMG indexable inserts, left-hand, no internal coolant (Teknik Makina) The S32T PCLNL is a left-hand boring bar engineered for PCLN holders and CNMG 1204 indexable inserts, delivering increased stiffness and reach for medium-duty turning and boring tasks in workshop and production environments S32T PCLNL ISO shank, 32 mm shaft For CNMG 1204 indexable inserts Left-hand cutting direction, 95° cutting angle No internal coolant; 300 mm overall length Increased precision and rigidity for stable turning results The combination of a 32 mm shank and a substantial nominal diameter of 40 mm provides enhanced rigidity under load, reducing deflection during interrupted cuts and off-centre machining. This improved stiffness translates into more consistent surface finish and tighter dimensional control when using indexable tooling. Machinists benefit from a robust toolholder that maintains the set geometry over longer tool overhangs, so repeatable turning performance becomes easier to achieve on small-batch jobs and serial production alike. The construction supports a cutting height of 50 mm, which ensures correct insert seating and consistent chip formation. Practical coolant strategy and chip control for reliable processes Designed without internal coolant, this version suits applications where external coolant or dry machining is preferred. The absence of internal channels simplifies maintenance and eliminates clogging risks in chip-heavy operations while still allowing efficient external fluid delivery or air blow-off. The left-hand cutting orientation combined with a 95° cutting angle offers predictable cutting forces for left-handed toolpaths and helps to direct chips away from the workpiece. For workshops adapting to varied coolant arrangements, this toolholder provides a straightforward, low-maintenance option that integrates with existing chip evacuation practices. Compatibility, handling and workshop integration Compatibility with CNMG 1204 indexable inserts makes the toolholder versatile for a broad range of turning applications, from semi-finishing to profile turning, using widely available carbide grades. The ISO designation S32T PCLNL indicates the shank form and holder geometry expected by standard PCLN systems, simplifying procurement and tooling inventory. With a total length of 300 mm and a mass of approximately 1.815 kg, the tool balances reach and handling—suitable for manual setup or CNC turret use. The clamping designation "12" defines the clamping interface and aids selection of matching clamping equipment or adapters to ensure secure fixation during high-feed operations. Discuss application requirements with Metav Werkzeuge to confirm that the S32T PCLNL boring bar suits the intended left-hand turning tasks; Metav Werkzeuge can advise on insert grades, clamping and coolant strategy—contact via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: P352TM Manufacturer: Teknik Makina Designation: PCLN for CNMG indexable inserts ISO designation: S32T PCLNL Numbers / Core technical data Shaft diameter: 32 mm Cutting height: 50 mm Overall length: 300 mm Diameter (nominal): 40 mm Weight: 1.815 kg Cutting angle: 95° Clamping designation: 12 Design / Special features Left-hand cutting direction Without internal coolant For CNMG 1204 indexable inserts PCLN holder geometry FAQ Which inserts fit this toolholder? The toolholder accepts CNMG 1204 indexable inserts; the PCLN seat geometry is matched to standard CNMG sizes for straightforward use. Can the boring bar be used with internal coolant systems? This variant is specified without internal coolant; internal delivery is not available, so external coolant or dry machining is recommended for this bar. Is the S32T PCLNL suitable for CNC turret use? Yes, the ISO shank form and 32 mm shaft make the S32T PCLNL appropriate for turret-mounted turning centres and stable manual setups alike. What does the left-hand designation mean for setup? Left-hand cutting direction indicates the bar is intended for left-hand toolpaths; the 95° cutting angle and orientation should be matched to the machine's tool numbering and programme direction. How does the 300 mm overall length affect performance? A 300 mm reach offers extended access to bore or turn deeper features while the 32 mm shank and mass of 1.815 kg help maintain stability; however, overhang should always be minimised to reduce deflection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid clamping with a 25 mm shank, precise compatibility with CNMG 1204 inserts and a compact 250 mm overall length for reliable left‑hand turning operations; order the P350TM directly via Metav Werkzeuge or consult the technical team for application advice. P350TM S25S PCLNL Boring Bar – PCLN for CNMG Inserts, 25 mm Shank (Left‑hand) by Teknik Makina The P350TM is a left‑hand PCLN‑style boring bar designed for secure indexable‑insert turning with CNMG 1204 inserts, offering a compact 250 mm overall length for stable lathe work Left‑hand cutting orientation 25 mm shank diameter for stable clamping Compatible with CNMG 1204 inserts No internal coolant for dry machining Consistent rigidity for repeatable turning The tool provides stable machining through its 25 mm shank and a balanced body with a 250 mm overall length, which together reduce vibration and deflection during engagement. That structural stability supports predictable tool life and consistent surface finish, allowing for higher feed rates where the process permits. The specified 32 mm diameter and the measured weight (0.978 kg) reflect a compact, easy‑to‑mount design that still delivers the torsional stiffness expected in industrial turning tasks. For purchasers assessing fixture requirements, the clear numerical values enable straightforward planning of toolholders and machine set‑up. Optimised insert pairing and predictable cutting geometry Engineered for use with CNMG 1204 indexable inserts in a PCLN pocket, this boring bar accepts the widely available turning grades used across general engineering and subcontract machining. The 95° cutting angle and a cutting height of 50 mm ensure the insert seat aligns reliably with common insert geometries, simplifying insert selection and reducing set‑up time. The left‑hand orientation is suitable for specific turning directions and applications where reverse cutting is required; in addition, the no internal coolant configuration is intended for operations using external coolant or dry machining strategies, which can be beneficial when internal channels are a contamination or maintenance concern. Built for workshop integration and efficient servicing The modular concept — replaceable CNMG inserts and a standard S25S PCLNL mounting style — reduces downtime and keeps maintenance straightforward: worn cutters are changed rather than the whole bar. That approach supports a cost‑effective production flow and aligns with Metav’s focus on supplying accessible precision for workshops of all sizes. Technical decisions such as clamping designation 12, the left‑hand cut type and the absence of internal coolant mean the bar integrates well into existing tool inventories while meeting requirements for repeatable part quality. For specification clarifications or to confirm suitability for a particular material or machining strategy, the sales engineers at Metav Werkzeuge are available to provide detailed comparisons and recommendations. Contact Metav Werkzeuge to discuss the Tek­nik Makina P350TM boring bar, confirm compatibility with specific CNMG grades and arrange supply directly from the Emmerich stock. Technical Data Article number: P350TM Manufacturer: Teknik Makina ISO designation: S25S PCLNL Model type: PCLN for CNMG Indexable Inserts Facts Shank diameter: 25 mm Overall length: 250 mm Diameter: 32 Cutting height: 50 mm Weight: 0.978 kg Cutting angle: 95° Insert type: CNMG 1204 Cutting direction: left Special feature: without Coolant Special features Compatible with CNMG 1204 inserts PCLN insert pocket geometry Left‑hand cutting orientation No internal coolant Clamping designation: 12 FAQ Which insert type fits this boring bar? The P350TM accepts CNMG 1204 indexable inserts in a PCLN pocket; Teknik Makina designed the seat and cutting height to match that insert size for reliable seating and repeatable results. Is this a left‑hand or right‑hand tool? This boring bar is a left‑hand tool, intended for machining operations that require left‑hand cutting direction; check machine spindle rotation and part set‑up before selection. Can internal coolant be used with this bar? The bar is supplied without internal coolant; it is suitable for dry machining or for use with external coolant supply systems rather than through‑tool cooling. What are the key dimensions to check for toolholder compatibility? Important values are the 25 mm shank diameter, 250 mm overall length, 32 mm diameter and cutting height 50 mm; these figures help determine holder fit and clearance on the lathe. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the robust S32T PCLNR design, stable 32 mm shank and compatibility with CNMG 1204 inserts for consistent turning performance; order the tool via Metav Werkzeuge or request technical advice from our consultants. P342TM – Boring bar (PCLN for CNMG indexable inserts) by Teknik Makina, S32T PCLNR, 32 mm shank A robust right‑hand boring bar designed for secure clamping of CNMG 1204 indexable inserts, optimised for conventional turning tasks without internal coolant. S32T PCLNR holder for CNMG inserts 32 mm shank for stable clamping Compatible with CNMG 1204 indexable inserts Right-hand cutting, without internal coolant Precise stability for repeatable boring results The holder’s 32 mm shank and solid construction provide enhanced rigidity during turning, which reduces vibration and supports dimensional accuracy. The S32T PCLNR designation denotes a standardised shank and head geometry, enabling predictable behaviour in lathes and turret systems. This stability is particularly relevant when machining medium‑diameter bores and when repeatability across multiple workpieces is required, leading to fewer reworks and improved process reliability. Efficient setup and insert interchangeability Compatibility with CNMG 1204 indexable inserts simplifies tooling logistics and minimises downtime: standard insert sizes allow rapid insert changes and straightforward inventory management. The right‑hand cutting orientation and the specified cutting height 50 mm ensure correct seat alignment for common turning operations. For workshops aiming to streamline set‑up times, this holder supports quick, reproducible clamping of the cutting edge, reducing preparation time between jobs. Design decisions that suit dry machining Specified without internal coolant, the bar is intended for applications where external cooling is preferred or where coolant is omitted for process reasons. The 95° cutting angle and the holder geometry are matched to conventional CNMG insert geometries, optimising chip flow and contact conditions at the tool tip. Where dry turning is chosen for part quality or downstream processing, the construction of this tool contributes to stable thermal behaviour and consistent surface finish. Practical dimensions and handling on the shop floor With a 300 mm overall length and an effective diameter related to a 40 mm body, the boring bar offers sufficient reach for many internal turning tasks while keeping overhang manageable. The unit weight of 1.815 kg gives a tangible sense of robustness without excessive mass that could complicate handling during tool changes. The combination of measured dimensions and a standardised holder interface supports predictable machine behaviour and easier tool inventory planning. For solid performance in turning operations, contact Metav Werkzeuge to discuss the Teknik Makina P342TM boring bar — technical advice and order handling are available from our Emmerich distribution centre at info@metav-werkzeuge.com or by telephone on +49 2822 7131930. Technical data Article number: P342TM Manufacturer: Teknik Makina Shank diameter: 32 mm Overall length: 300 mm Weight: 1.815 kg Cutting height: 50 mm Body diameter: 40 mm Cutting angle: 95° Cutting direction: right ISO designation: S32T PCLNR For indexable inserts: CNMG 1204 Holder type: PCLN for CNMG indexable inserts Special feature: without internal coolant FAQ What insert type fits this holder? The holder is compatible with CNMG 1204 indexable inserts; the PCLN seating ensures correct positioning for CNMG geometry. Is this tool suitable for internal coolant systems? The P342TM is specified without internal coolant; it is intended for dry machining or external coolant arrangements. What is the shank size and overall reach? The boring bar has a 32 mm shank diameter and a 300 mm overall length, offering a balanced reach for many internal turning tasks. Which cutting direction is supported? This tool is configured for right‑hand cutting, matching common lathe setups for conventional turning. How does the S32T PCLNR designation affect compatibility? The S32T PCLNR ISO designation describes the shank and head form, aiding compatibility with tool holders and ensuring standardised mounting and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Secure reliable, vibration‑reduced turning with a focus on compatibility and stiffness: the combination of a 25 mm shank, a 95° cutting angle and compatibility with CNMG 1204 inserts supports steady chip control and consistent surface finish. Order the tool directly via Metav Werkzeuge or ask our consultants if needed. Bohrstange P340TM — Turning tool holder PCLN for CNMG indexable inserts, 25 mm shank (Teknik Makina) Bohrstange P340TM is a PCLN‑style turning tool holder designed for application with CNMG indexable inserts in right‑hand turning operations, offering a compact 250 mm overall length for stable setups. Right‑hand PCLN holder Shank diameter 25 mm For CNMG 1204 inserts Without internal coolant Consistent insert compatibility for predictable machining The holder is optimised for CNMG 1204 indexable inserts, which are widely used and readily available. Using this standard insert family reduces tooling complexity and shortens changeover times. The PCLN geometry secures the insert on a robust pocket and, combined with the ISO designation S25S PCLNR, ensures a predictable seat and clamping position. This translates into repeatable tool offsets on CNC lathes and fewer adjustments during batch production. Increased stiffness and improved surface quality from robust dimensions With a 25 mm shank and overall length 250 mm, the bar offers a favourable stiffness‑to‑reach ratio for many light to medium turning tasks. The substantial cross‑section helps to damp vibrations, which improves surface finish and extends insert life. The 95° cutting angle provides versatile engagement for facing and light profiling, while the measured mass (0.978 kg) contributes to stability in dynamic cuts without adding unnecessary inertia to the toolpost. Practical setup and machining considerations for efficient use The tool is supplied without internal coolant, so external coolant or flood lubrication should be used where chip evacuation and temperature control are required. The right‑hand cutting orientation and the nominal clamping size 12 make the bar compatible with typical toolposts and clamping systems; the ISO tag S25S PCLNR aids correct selection of holders and adapters. For operations requiring through‑tool coolant, select a dedicated coolant‑capable holder; otherwise, this bar excels for dry or externally cooled finishing and semi‑finishing cuts. For technical availability or to discuss suitability for a specific turning task with Teknik Makina's P340TM, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and prompt supply. Technical data Article number: P340TM Manufacturer: Teknik Makina Designation: Boring bar / Turning tool holder (PCLN for CNMG indexable inserts) ISO designation: S25S PCLNR Facts Shank diameter: 25 mm Cutting height: 50 mm Weight: 0.978 kg Diameter: 32 mm Overall length: 250 mm Cutting angle: 95° Special features For CNMG 1204 indexable inserts Right‑hand cutting direction Without internal coolant Clamping size 12 ISO designation: S25S PCLNR FAQ Which inserts are compatible with this holder? The P340TM accepts CNMG 1204 indexable inserts and is designed around the CNMG pocket and clamping geometry for secure seating. Is internal coolant supplied through the tool? No — the P340TM is supplied without internal coolant; external flood or mist lubrication is recommended where coolant is needed. What are the shank diameter and overall length? The holder has a 25 mm shank and an overall length of 250 mm, providing a balance between reach and rigidity. Which cutting direction does the bar support? This tool is configured for right‑hand cutting operations (PCLN geometry). What is the ISO designation of the tool? The tool carries the ISO designation S25S PCLNR, which aids selection of compatible holders and adapters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a rigid Ø20 mm shaft, secure compatibility with CNMG 1204 inserts and a compact 200 mm overall length, this boring bar delivers stable cuts and predictable tool life for turning applications. Order the tool via Metav Werkzeuge or request technical advice from their consultants for immediate supply from Emmerich. Boring bar PCLN for CNMG indexable inserts — Teknik Makina S20R PCLNR, Ø20 mm The boring bar PCLN for CNMG Indexable Inserts is a right‑hand turning tool designed for CNMG 1204 inserts, offering a compact 200 mm length and a robust Ø20 mm shank for secure clamping in common toolposts and turrets. Shaft Ø20 mm for rigid clamping Designed for CNMG 1204 indexable inserts 200 mm overall length for versatile reach Without internal coolant for external supply Stable clamping for consistent machining results A toolholder built around a Ø20 mm shank provides improved rigidity, reducing chatter during heavy cuts and finishing passes. The ISO designation S20R PCLNR indicates a standard shank and head layout that fits many lathe toolposts; this makes fixture planning straightforward and repeatable. By lowering vibration and deflection, the design contributes directly to extended insert life and more predictable surface finishes, which reduces rework and downtime on production batches. Compatibility with CNMG 1204 inserts for flexible turning Prepared for CNMG 1204 indexable inserts, the turning bar accepts a widely available insert geometry that suits roughing and finishing when matched to the appropriate grade. The tool’s 95° cutting angle and right‑hand cutting direction support conventional turning setups and stable plunge behaviour. Because the bar is specified without internal coolant, cooling strategy is external by design — this simplifies the holder construction and is ideal for dry machining or systems where coolant is supplied externally. Practical dimensions that suit busy workshops With a 200 mm overall length and a nominal diameter of 24 mm at the head, the holder balances reach and stiffness for internal or external operations in confined setups. The 50 mm cutting height and the modest weight of 0.54 kg make handling and tool changes easy for technicians while keeping centre‑of‑gravity shifts minimal when mounted. These dimensions support quicker set‑ups and predictable toolpaths, improving throughput without compromising process stability. Built for professional workflows and reliable supply Manufactured by Teknik Makina and stocked by Metav, the holder is aimed at machining centres and workshops that demand dependable tooling ready for immediate use. The simple construction—no internal coolant—reduces potential leak paths and maintenance points, while the standard geometry ensures compatibility with established clamping systems. Combined with Metav’s logistics and technical support, this solution is suitable for integration into both single‑machine shops and serial production environments. Contact Metav Werkzeuge for tailored machining advice and fast supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number (SKU): P338TM Brand: Teknik Makina ISO designation: S20R PCLNR Facts Shaft diameter: 20 mm Cutting height: 50 mm Overall length: 200 mm Weight: 0.54 kg Head diameter: 24 mm Cutting angle: 95° Cutting direction: right Special features Fits CNMG 1204 indexable inserts Without internal coolant Suitable for standard toolpost mounting Compact design for internal and external boring FAQ What insert type does this boring bar accept? The Tek­nik Ma­ki­na boring bar is designed for CNMG 1204 indexable inserts, allowing use of standard grades for roughing or finishing. Is this holder suitable for internal boring in small bores? Yes, with its 200 mm overall length and compact head diameter the bar is suitable for many internal and external turning setups where reach and rigidity must be balanced. Does the tool provide internal coolant feed? The holder is specified without internal coolant; coolant must be supplied externally or omitted for dry machining applications. Which cutting direction does the tool support? The bar is configured for right‑hand cutting, matching typical lathe feed directions for conventional turning operations. What is the ISO designation and why is it relevant? The S20R PCLNR designation describes the shank and head form, ensuring compatibility with standard toolpost clamping systems and aiding selection for machine setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid 40 mm shank and internal coolant to improve cycle stability and tool life. The integrated design for CNMG 1204 indexable inserts delivers consistent chip control and repeatable bore quality — order directly via Metav Werkzeuge or consult the team for application-specific setup. A40T PCLNL Boring Bar – PCLN for CNMG Indexable Inserts, 40 mm Shank – Teknik Makina The A40T PCLNL is a left-hand boring bar engineered for turning applications with CNMG 1204 indexable inserts, combining a robust 40 mm shank with internal coolant for improved process reliability. A40T PCLNL boring bar for CNMG 1204 inserts Internal coolant supply for optimised chip evacuation 40 mm solid shank, 300 mm overall length Left-hand orientation with 95° cutting angle Stable bore quality from a rigid shank and precise geometry A solid 40 mm shank and the specified 300 mm overall length provide a balance between reach and stiffness, minimising vibration during heavy cuts. The tool’s geometry — a 95° cutting angle and generous 55 mm cutting height — supports consistent edge engagement when used with CNMG 1204 indexable inserts. In practice, this reduces surface irregularities and rework, enabling more predictable process planning in serial production and toolroom environments. Controlled cooling and chip evacuation to extend tool life The integrated internal coolant channels target the cutting zone directly, enhancing heat removal and aiding chip breakage. Improved cooling stabilises cutting temperatures, which in turn preserves insert edge integrity and delays wear. For operations requiring extended tool life and fewer tool changes, the internal coolant capability contributes to reduced downtime and a more economical machining cycle. Compatibility and quick installation for efficient setups Designed for CNMG-type indexable inserts, the holder matches common clamping systems and is identified by ISO designation A40T PCLNL. The clamping-holder designation (12) supports secure insert retention and repeatable indexability. The bar’s specification and weight (1.82 kg) facilitate straightforward handling during setup while ensuring sufficient mass for steady machining. This makes the component suitable for medium to heavy turning tasks where reliable clamping and coolant supply are required. Practical advantages for production environments By pairing proven insert geometry with targeted coolant delivery and a robust shank, the assembly improves process stability and reduces the frequency of corrective machining. The left-hand orientation is advantageous where component clamping or machine tool configuration demands reverse cutting direction. Overall, the design prioritises manufacturability and repeatable performance for workshops and production lines using CNMG inserts. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina A40T PCLNL boring bar into existing tooling arrays or to request application-specific recommendations; Metav’s specialists will support selection and setup from Emmerich. Technical Data Article number: AP354TM Manufacturer: Teknik Makina ISO designation: A40T PCLNL Facts Shank diameter: 40 mm Cutting height: 55 mm Weight: 1.82 kg Overall length: 300 mm Diameter: 50 mm Cutting angle: 95° Compatible inserts: CNMG 1204 Direction of cut: left Special features Internal coolant With coolant / mit Innenkühlung For CNMG indexable inserts (PCLN) Clamping holder designation: 12 FAQ Which insert type fits this boring bar? The A40T PCLNL is specified for CNMG 1204 indexable inserts and is optimised for those insert geometries. Is coolant supplied internally or externally? This boring bar provides internal coolant, delivering fluid directly to the cutting zone for improved cooling and chip control. What shank diameter and length are available for this model? The product has a 40 mm shank and a 300 mm overall length, offering a balance of stiffness and reach for many turning tasks. Is the cutting direction left-hand or right-hand? The holder is a left-hand orientation with a 95° cutting angle, suitable where reverse-direction cutting is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid 32 mm shank, coolant-fed design and direct compatibility with CNMG 1204 inserts for stable, repeatable turning and facing operations; the tool’s 300 mm overall length gives extended reach while maintaining stiffness. Order the boring bar directly via Metav Werkzeuge or ask our consultants if needed. Boring bar A32T PCLNL — coolant-fed PCLN holder for CNMG 1204 indexable inserts (Teknik Makina) Boring bar A32T PCLNL is a coolant-supported turning bar intended for left-hand cutting operations with CNMG 1204 indexable inserts, suited to workshop and production use where rigid clamping and controlled chip evacuation are required. Boring bar A32T PCLNL by Teknik Makina Internal coolant for consistent chip evacuation Compatible with CNMG 1204 indexable inserts Stable machining and predictable chip control The A32T PCLNL holder combines a 32 mm shank with a robust holder body to reduce vibration and improve surface finish on the workpiece. The geometry accommodates CNMG 1204 indexable inserts and a 95° cutting angle, which together deliver a secure cutting action and reliable tool engagement. For applications where dimensional consistency and repeatability are essential, the construction of this holder increases process stability and lowers scrap rates by limiting deflection during heavy cuts. Coolant feed and extended insert life Built-in internal coolant directs lubricant and coolant close to the cutting edge, supporting efficient heat removal and chip breaking. The internal feed reduces thermal load on the insert and cutting edge, which contributes to longer tool life and more consistent cycle times. With an overall length of 300 mm, the holder balances reach with stiffness; this configuration is beneficial for medium-reach boring and external turning where coolant-assisted chip control is required to maintain machining quality. Practical applications and integration into workflows Designed for left-hand cutting and specified as A32T PCLNL in ISO terms, the holder suits general turning, facing and light boring tasks when fitted with the specified inserts. The tool is supplied for use with CNMG 1204 plates and is therefore compatible with a broad range of carbide grades and coatings offered by insert manufacturers. Its 40 mm diameter body and a cutting height of 50 mm allow secure clamping and straightforward integration into existing tool posts and turret systems, supporting efficient changeover and consistent set-ups across production batches. For specification advice or to arrange supply of the Teknik Cutting Tools A32T PCLNL coolant-fed boring bar, contact Metav Werkzeuge for tailored recommendations and prompt delivery arrangements. Technical data Article number: AP352TM Manufacturer: Teknik Makina ISO designation: A32T PCLNL Designation: PCLN for CNMG Indexable Inserts Dimensions & weight Shank diameter: 32 mm Overall length: 300 mm Cutting height: 50 mm Diameter: 40 mm Weight: 1.809 kg Cutting angle: 95° Features & applications Internal coolant: yes Suitable for CNMG 1204 inserts Left-hand cutting direction Coolant-fed holder design FAQ What inserts fit this holder? The holder is specified for use with CNMG 1204 indexable inserts; the PCLN style accepts the standard CNMG plate geometry for turning and facing. Does the tool provide internal coolant? Yes, the A32T PCLNL boring bar features internal coolant to improve chip evacuation and reduce cutting temperatures during operation. What are the key dimensions for set-up? Key measurable data are listed above: shank diameter 32 mm, overall length 300 mm, diameter 40 mm and cutting height 50 mm, which support accurate fixture and clamping planning. Is the cutting direction important for this tool? The tool is designed for left-hand cutting; confirm the machine turret orientation and program directions to ensure correct installation and machining direction. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of precise 95° cutting geometry and integrated internal coolant for consistent metal removal and extended tool life. Compatibility with CNMG 1204 indexable inserts plus a robust Ø20 mm shank delivers secure clamping and dimensional stability in production environments. Order the boring bar directly via Metav Werkzeuge or consult our specialists if required. A20R PCLNR boring bar — PCLN for CNMG indexable inserts, internal coolant (Teknik Makina) The A20R PCLNR boring bar is a right‑hand tool engineered for finishing and bore‑facing operations, featuring internal coolant and an ISO A20R PCLNR designation for CNMG‑type indexable inserts. 95° cutting angle for stable cutting Internal coolant for improved tool life Compatible with CNMG 1204 inserts Shank Ø20 mm, overall length 200 mm Precise geometry for dependable chip control and surface finish The 95° cutting angle and PCLN geometry combine to provide a stable cutting action that reduces vibration and promotes predictable chip formation. For practical use this means fewer interrupted cuts and a more consistent surface finish when machining bores or facing close tolerances. The tool accepts CNMG 1204 indexable inserts, a common industry standard; these inserts allow the machining parameters to be adapted by selecting the appropriate grade and geometry for the workpiece material. By pairing a proven insert form with the bar’s right‑hand configuration, the assembly is optimised for finishing passes where dimensional accuracy and repeatability are priorities. Internal coolant for thermal control and longer tool life An integral coolant channel delivers lubricant and coolant directly to the cutting zone, which helps to evacuate heat and improve chip flow. This internal coolant arrangement reduces thermal distortion of the tool and workpiece, supporting longer tool life and a more consistent bore diameter over extended runs. In production scenarios where cycle time and part quality matter, targeted coolant supply reduces the need for frequent tool inspection and tempering of cutting data. The result is a lower total cost of operation through fewer tool changes and improved process stability. Robust design for secure clamping and easy integration With a Ø20 mm shank and an overall length of 200 mm, the bar offers a balance between rigidity and reach for typical centre‑lathe and CNC turret set‑ups. The ISO designation A20R PCLNR identifies the toolholder form, simplifying tool‑room inventory and ensuring compatibility with standard clamping systems. A modest mass (approx. 0.52 kg) supports rapid accelerations without compromising stability. In practice, this means reliable performance in mixed‑batch work and easier handling during tool changes; the combination of solid geometry and internal coolant makes the tool suitable for high‑precision finishing operations where consistent results are required. Contact Metav Werkzeuge for tailored technical advice and assured supply from Emmerich — quote SKU AP338TM when enquiring for faster processing Technical Data Article number: AP338TM Manufacturer: Teknik Makina ISO designation: A20R PCLNR Type: PCLN for CNMG indexable inserts Special feature: with Coolant Facts Shank diameter: 20 mm Diameter: 24 mm Overall length: 200 mm Cutting height: 50 mm Cutting angle: 95° Weight: 0.52 kg Cutting direction: right Special features Internal coolant supply Compatible with CNMG 1204 inserts ISO form: A20R PCLNR Suitable for finishing and bore operations FAQ Which insert type fits this boring bar? The boring bar is designed for CNMG 1204 indexable inserts; the PCLN geometry is matched to that insert form for stable seating and secure clamping. Does the bar provide coolant directly to the cutting edge? Yes — the tool features internal coolant that delivers fluid to the cutting zone, supporting thermal control and improved chip evacuation. What are the shank and overall dimensions? Shank Ø is 20 mm with an overall length of 200 mm, providing a balance of rigidity and reach for typical lathe and turret installations. Is this tool suitable for heavy roughing or finishing? The design and 95° cutting angle are optimised for finishing and bore‑facing operations; for heavy roughing a more rigid, larger‑section holder may be preferable. How is the tool identified in ISO form? The bar carries the ISO designation A20R PCLNR, which helps with tool selection and ensuring compatibility with standard clamping systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigidity from the 40 mm shaft, internal coolant and compatibility with CNMG 1204 inserts for precise, stable turning operations; order directly via Metav Werkzeuge or consult our specialists if guidance is required. Boring Bar AP344TM — PCLN for CNMG indexable inserts, internal coolant (Teknik Makina) The Boring Bar AP344TM is a right-hand turning bar designed for heavy-duty and precision facing with CNMG 1204 indexable inserts, suited to demanding workshop and production environments. A40T PCLNR ISO designation Internal coolant channel for stable cutting Compatible with CNMG 1204 inserts 40 mm shaft for increased rigidity Maximised rigidity for consistent machining results The turning tool is built around a 40 mm shaft, which significantly increases rigidity and reduces deflection under load. This construction, combined with the A40T PCLNR ISO form, delivers a stable platform for roughing and finishing operations, so that the machining process produces repeatable diameters and surface quality. The robust design minimises chatter and supports longer tool life of the indexable inserts, translating into fewer tool changes and more productive machine time. Integrated coolant for improved tool life and edge stability An internal coolant channel is integrated into the bar to deliver cutting fluid directly to the cutting zone. The internal coolant supply controls temperature at the edge, reduces built-up edge and assists chip control when using CNMG 1204 inserts. In practice, this means improved insert life and more consistent cutting forces, particularly during medium to heavy cuts. Explaining the technical effect: coolant at the rake reduces thermal shock and carries away chips, which helps preserve the sharpness and geometry of the cutting edge. Ready-to-fit compatibility and straightforward setup Designed for indexable turning, the bar accepts CNMG 1204 inserts in a PCLN configuration, making it straightforward to integrate into existing toolholders and setups. The right-hand cut orientation and the standard clamping interface simplify repeatable mounting and alignment. With a 300 mm overall length and a 55 mm cutting height, the tool is dimensioned to suit standard lathes and turret setups while keeping the centre of gravity and overhang balanced for better dynamic behaviour. Shop-floor reliability and measurable benefits Performance is backed by measurable specifications such as a 95° cutting angle and a compact mass of 1.82 kg, contributing to controlled cutting dynamics and manageable handling during changeover. The combination of precision geometry, coolant support and a sturdy shaft reduces scrap rates and improves first-pass yield. For procurement and planning, the tool represents a practical investment where predictable process capability and reduced downtime are priorities. For ordering or technical consultation regarding the Teknik Makina AP344TM boring bar, contact Metav Werkzeuge for assistance and delivery from the Emmerich quality hub. Technical Data Article number: AP344TM Manufacturer: Teknik Makina ISO designation: A40T PCLNR Insert type: PCLN for CNMG indexable inserts Cutting direction: right Special feature: with Coolant Facts Shaft diameter: 40 mm Overall length: 300 mm Cutting height: 55 mm Weight: 1.82 kg Diameter: 50 mm Cutting angle: 95° Special features Internal coolant (through-tool coolant) Compatible with CNMG 1204 inserts Right-hand cutting orientation ISO A40T PCLNR form FAQ What inserts fit this boring bar? The boring bar accepts CNMG 1204 indexable inserts in a PCLN arrangement; the AP344TM is specified for this insert size and geometry. Does the bar supply coolant to the cutting edge? Yes, the AP344TM features an internal coolant channel that delivers fluid directly to the insert cutting zone for improved tool life. What are the key dimensions to check before ordering? Check the shaft diameter (40 mm), overall length (300 mm) and cutting height (55 mm) to ensure compatibility with the machine turret and clearance. Is this a right- or left-hand tool? This model is a right-hand turning bar, suitable for conventional right-hand turning operations. Who manufactures the tool and who is responsible for distribution? Teknik Makina is named as the manufacturer and the product is distributed via Metav Werkzeuge for the European market. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid holder design, precise ISO compatibility and through-tool coolant for consistent internal turning results; order the boring bar directly via Metav Werkzeuge or ask our consultants if needed. Boring Bar AP342TM — PCLN holder for CNMG indexable inserts with internal coolant (Teknik Makina) Boring Bar AP342TM is a right-hand PCLN-style holder designed for internal turning with CNMG indexable inserts, combining secure clamping with coolant-through functionality for demanding CNC applications. Internal coolant for reliable cooling and chip control For CNMG 1204 indexable turning inserts Shank diameter 32 mm for stable clamping ISO A32T PCLNR holder, 95° cutting angle Stable clamping and geometric support for consistent bore quality The tool is built around a 32 mm shank and a robust body that reduces deflection during internal turning. This geometry improves repeatability in serial production and supports accurate bore tolerances when machining with indexable tips. The combination of the holder's mass and the specified 95° cutting angle promotes a stable cutting condition and lowers vibration, which translates into improved surface finish and longer insert life for the turning process. Coolant-through design that protects inserts and workpieces Equipped with internal coolant, the holder ensures directed coolant delivery to the cutting edge for effective heat removal and chip evacuation. This feature is particularly valuable in deep boring operations where access for external coolant is limited. By feeding coolant directly to the cutting zone the tool reduces thermal load on the insert and aids consistent chip breaking, helping to maintain dimensional stability and reduce rework in assembly workflows. Wide compatibility with standard indexable inserts and ISO holder form The AP342TM accepts CNMG 1204 indexable inserts and follows the A32T PCLNR ISO designation, making it straightforward to integrate into existing tooling systems and spare-part inventories. Its right-hand cutting orientation suits conventional internal turning cycles in CNC lathes. The standardised interface simplifies insert changes and minimises machine downtime, supporting efficient process chains in jobbing and small-batch production. Contact Metav Werkzeuge in Emmerich for availability and delivery details: info@metav-werkzeuge.com — call +49 2822 7131930 for tailored application advice and stock information Technical data Article number: AP342TM ISO designation: A32T PCLNR Designation: PCLN for CNMG indexable inserts Brand: Teknik Makina Facts Diameter: 40 mm Shank diameter: 32 mm Overall length: 300 mm Cutting height: 50 mm Weight: 1.809 kg Cutting angle: 95° Direction: right-handed Compatible insert: CNMG 1204 Special features Internal coolant (through-tool) With coolant Right-hand cutting direction For CNMG indexable inserts ISO holder type A32T PCLNR FAQ What insert type does this holder accept? This holder is specified for CNMG 1204 indexable inserts and is configured to secure standard CNMG-style tips for internal turning. Is coolant supplied through the holder? Yes, the AP342TM features internal coolant (coolant-through) to direct fluid to the cutting edge for improved cooling and chip control. Which ISO designation identifies the holder form? The tool follows the A32T PCLNR ISO designation, which clarifies the holder form and helps match compatible spares and clamping systems. What are the main dimensions relevant for machine setup? Key dimensions are a 40 mm diameter, 32 mm shank, and 300 mm overall length; the cutting height is 50 mm and the tool weight is 1.809 kg. Is the cutting direction right- or left-handed? The holder is configured for right-handed cutting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a secure clamping system, internal coolant and precise compatibility with CNMG 1204 inserts for consistent turning performance; order directly via Metav Werkzeuge or consult our specialists for application advice. Klemmhalter PCLN for CNMG Indexable Inserts — Right-hand turning holder with internal coolant (PCLNR 2020) by Teknik Makina The Klemmhalter PCLN for CNMG Indexable Inserts is a right-hand turning holder engineered for external turning with CNMG 1204 inserts; it combines secure clamping and coolant feed to support reliable production runs Right-hand turning holder for CNMG 1204 Internal coolant for improved chip evacuation ISO designation PCLNR 2020 for standardised fit 125 mm overall length with 28 mm cutting height Consistent clamping for repeatable turning results The holder's ISO designation PCLNR 2020 signifies a standardised fit and makes insert changes straightforward. The PCLN-style clamp secures CNMG 1204 indexable inserts via a robust clamp screw (TH821) together with the matching U‑plate (TA016-1) and locating pin (TS-4), which ensures repeatable seating and reduces set-up time. This precise clamping reduces insert micro-movement under cutting forces, translating into stable tool life and fewer interruptions during batch production. Cooler cutting and improved surface finishes Built-in internal coolant supplies coolant directly to the cutting zone, helping to control temperature and evacuate chips more effectively. By reducing thermal load and swarf contact at the cutting edge, the holder can extend insert life and promote a more consistent surface finish on turned components. For operations that prioritise cycle-time reliability and dimensional repeatability, the coolant provision supports higher feeds and steady metal removal rates without sacrificing quality. Compact, rigid design for versatile turning operations With an overall length of 125 mm, a cutting height of 28 mm and a cutting head width of 25 mm, the toolholder balances reach and rigidity for general external turning tasks. The holder's right-hand orientation and a specified cutting angle of 95° make it suitable for facing and general-purpose turning where access and clearance are factors. Weighing 0.428 kg, the tool is easy to handle during mounting yet substantial enough to damp vibrations, supporting precise machining results across small to medium batches. Discuss application requirements with Metav Werkzeuge—our specialists can advise on the PCLN holder, mounting components and compatible CNMG 1204 inserts; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: AP130TM Manufacturer: Teknik Makina Facts Holder height: 20 mm Cutting head width: 25 mm Holder width: 20 mm Cutting height: 28 mm Overall length: 125 mm Weight: 0.428 kg Cutting angle: 95° Internal coolant: yes Special features ISO designation: PCLNR 2020 Suitable for: CNMG 1204 inserts Cutting direction: right Clamp screw: TH821 U‑plate: TA016-1 Locating pin: TS-4 Knee lever: TL4 Allen key: 3 Allen FAQ Is this holder compatible with CNMG 1204 inserts? The PCLN holder is designed for CNMG 1204 indexable inserts and secures them in the standard PCLNR 2020 seat. Does the holder provide coolant to the insert? Yes, the turning holder features internal coolant, supplying fluid to the cutting zone for improved chip control and temperature management. Which cutting direction is supported by the holder? This toolholder is specified for right-hand turning operations. What mounting components are included or required? The design pairs with the TH821 clamp screw, TA016-1 U‑plate and TS-4 locating pin; the knee lever is TL4 and an Allen key (3 Allen) is referenced for assembly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑conformant toolholder that combines reliable clamping with compatibility for CNMG 1204 inserts; the right‑hand design and 95° cutting angle support stable turning operations and extended reach. Order directly via Metav Werkzeuge or contact the sales team for technical guidance. Clamping Holder PCLN for CNMG Indexable Inserts (PCLNR 2020) – Teknik Makina The Clamping Holder PCLN for CNMG Indexable Inserts is a right‑hand toolholder designed for turning applications that accept CNMG 1204 indexable inserts, delivering precise insert seating and robust clamping in workshop and production environments. Right-hand design for conventional turning Compatible with CNMG 1204 inserts 95° cutting angle for extended reach Reliable clamping and consistent cutting performance The holder delivers repeatable clamping accuracy through a proven mounting geometry, reducing insert movement during cutting and extending tool life. The 95° cutting angle improves access to shoulder areas while maintaining cutting stability. Where operators require predictable chip formation and reduced vibration, this toolholder provides a stable interface between machine and insert, helping to maintain surface finish and dimensional consistency over long production runs. Fast changeovers and broad insert compatibility Designed for standard CNMG 1204 inserts, the toolholder follows the PCLNR 2020 ISO designation to ensure interchangeability with common indexable grades and geometries. The K12 shank designation supports secure mounting in compatible toolposts and boring bars, enabling quick insert replacement and minimal downtime. This configuration simplifies inventory management, since conventional CNMG inserts from several manufacturers will seat correctly in the clamping pocket. Compact dimensions for constrained setups With an overall length of 125 mm and a cutting‑head width of 25 mm, the toolholder is compact enough for confined tooling layouts while offering a cutting height of 30 mm for proper insert alignment. The holder’s body width of 20 mm contributes to a slim profile that helps reach tight bores and close flank surfaces without compromising rigidity. The moderate weight (0.421 kg) balances mass and accessibility, supporting steady cutting without adding excessive overhang. Workshop durability and practical benefits Built for routine turning tasks, the toolholder’s right‑hand orientation and geometry deliver straightforward set‑up and predictable edge engagement. The combination of ISO conformity, compatible insert type (CNMG 1204) and standard shank specifications reduces the risk of mismatches at procurement and speeds commissioning on the shop floor. Routine maintenance focuses on insert seating and clamping screw checks, keeping life‑cycle effort minimal while ensuring continued cut quality. Contact Metav Werkzeuge today to secure the Teknik Makina PCLNR 2020 clamping holder for dependable right‑hand turning; assistance and supply are available directly from Metav Werkzeuge’s Emmerich site. Technical data Article number: P130TM Manufacturer: Teknik Makina Model designation (ISO): PCLNR 2020 Compatible inserts: CNMG 1204 Facts Weight: 0.421 kg Overall length: 125 mm Cutting height: 30 mm Holder width: 20 mm Cutting‑head width: 25 mm Cutting angle: 95° Cutting direction: Right Design / Special features Right‑hand cutting orientation Compatible with CNMG 1204 indexable inserts Shank/bar designation: K12 ISO toolholder form PCLNR 2020 FAQ What inserts fit this toolholder? The holder is designed for CNMG 1204 indexable inserts; the PCLNR 2020 pocket accepts standard CNMG insert sizes and seat geometries. Is this a right‑hand or left‑hand toolholder? This model is a right‑hand toolholder, optimised for conventional turning directions and shoulder work. What are the key dimensions to check before ordering? Verify overall length (125 mm), cutting height 30 mm and holder width 20 mm to ensure compatibility with the machine setup and toolpost. Which SKU should be ordered for this clamping holder? Order SKU P130TM for the Teknik Makina PCLNR 2020 clamping holder; Metav Werkzeuge can confirm availability and delivery options. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, left‑hand PCLN toolholder with internal coolant and a secure screw clamp — precise chip control and stable insert seating for efficient turning operations. Order the holder directly via Metav Werkzeuge or consult the technical team for application advice. PCLNL 1616 PCLN toolholder – left‑hand, internal coolant, for CNMG inserts (Teknik Makina) PCLNL 1616 PCLN toolholder is a left‑hand clamping toolholder designed for turning with CNMG indexable inserts; suited to standard toolposts and compact lathe setups. Left‑hand PCLN toolholder with internal coolant Fits CNMG 1204 indexable inserts Compact 16 x 16 mm shank body 95° cutting angle for versatile turning Secure clamping and consistent cutting performance Built from workshop‑grade specifications, this toolholder delivers reliable clamping and predictable behaviour during cyclic turning operations. The PCLNL 1616 format provides a familiar interface for indexable insert tooling, with a robust clamping screw (TH818) and matching support parts (U‑plate TA016‑1, dowel TS‑4, knee lever TL4) for stable insert seating. At 16 x 16 mm shank dimensions and a head width of 20 mm, the holder balances rigidity and compactness; the modest mass of 0.236 kg helps reduce unbalanced loads on smaller toolposts. These attributes reduce vibration and contribute to consistent surface finish and tool life. Optimised for CNMG inserts and left‑hand turning cycles The holder is engineered specifically for turning with CNMG 1204 indexable inserts and supports a 95° cutting angle, enabling effective approach geometry for a wide range of diametral cuts. Left‑hand orientation makes the assembly suitable for operations that require opposite feed or for machines configured for left‑hand turning. The integrated internal coolant channel directs lubricant close to the cutting edge, promoting chip evacuation and improved thermal control; the result is extended insert service life and fewer interrupted cycles for regrinding or replacement. Designed for quick set‑up and low maintenance in production Assembly and maintenance are straightforward thanks to standardised fittings: the clamping screw designation TH818, the locating plate TA016‑1, dowel TS‑4 and lever TL4 ensure repeatable seating and rapid replacement when turnarounds are required. The holder’s 100 mm overall length and defined cutting height of 28 mm enable predictable tool offsets and simple programme setup on CNC lathes. Internally routed coolant minimises manual coolant management and reduces downtime related to chip build‑up, supporting higher process uptime and smoother production flows. Contact Metav Werkzeuge to specify the right Teknik Makina PCLN toolholder and confirm compatibility with existing toolposts and CNMG inserts Technical Data Article number: AP139TM Manufacturer: Teknik Makina Type designation: PCLNL 1616 Facts Shank width: 16 mm Shank height: 16 mm Head width: 20 mm Cutting height: 28 mm Total length: 100 mm Weight: 0.236 kg Cutting angle: 95° Cutting direction: left Special features Internal coolant For CNMG 1204 indexable inserts Clamping screw TH818 U‑plate TA016‑1 Dowel TS‑4 Knee lever TL4 Allen key: 3 Allen Compatible with H12‑IKG1/8 drill‑bar designation FAQ What inserts are compatible with this holder? The holder is designed for CNMG 1204 indexable inserts; the PCLN format and clamping arrangement match standard CNMG seat geometries. Is the coolant routed to the cutting edge? Yes, the toolholder features internal coolant that directs fluid towards the insert to improve chip evacuation and temperature control. Which clamping components are required for assembly? Assembly uses the clamping screw TH818, locating plate TA016‑1, dowel TS‑4 and knee lever TL4, which provide repeatable clamping and alignment. Is this a left‑hand or right‑hand holder? This is a left‑hand PCLN toolholder intended for left‑hand turning applications. What are the shank dimensions and overall length? Shank dimensions are 16 x 16 mm with a 100 mm overall length and a head width of 20 mm, allowing compact mounting and predictable offsets. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust turning solution that pairs secure clamping with a compact 25 x 25 mm shank and a 75° approach angle for stable, repeatable machining; order via Metav Werkzeuge or request advice from our consultants for optimal workshop integration. DCKNR 2525 clamping tool holder — Right-hand, 75° approach angle, for CNMG 1204 inserts — Teknik Makina The DCKNR 2525 clamping tool holder secures CNMG 1204 indexable inserts for right-hand turning operations, designed for stable insert positioning and reliable performance in CNC and manual turning applications. Right-hand turning holder, 75° approach angle For CNMG 1204 indexable inserts 25 x 25 mm shank, 32 mm head width Robust construction, 0.44 kg weight Optimised for dependable turning performance The holder is specified for a 75° approach angle, a geometry that directs cutting forces effectively for many medium-to-heavy turning tasks. With a shank size of 25 x 25 mm and an overall length of 150 mm, the tool offers a compact footprint while maintaining the rigidity required for consistent chip control. Suitability for CNMG 1204 indexable inserts ensures access to a wide range of grade and geometry options; the insert seat and clamping arrangement provide secure seat contact, which reduces chatter and contributes to predictable surface finish and dimensional stability on the workpiece. Reduced setup time and improved process reliability A straightforward clamping design and standard thread engagement mean faster insert changes and minimal downtime. The clamping screw is specified as M12, enabling robust torque transfer for a firm hold without complex accessories. Because insert movement is minimised, insert life and machine uptime are supported by the mechanical design rather than by frequent readjustment. The holder’s mass of 0.44 kg balances handling ease with damping capability, helping to absorb cutting disturbances while enabling quick manual handling during tool changes. Simple integration with workshop tooling and machines Designed in accordance with the ISO designation DCKNR 2525, compatibility with common toolpost or turret setups is straightforward. The toolhead presents a 32 mm width and a cutting height of 30 mm, dimensions that match many standard turret slide clearances and clamping geometries. Right-hand turning orientation is clearly defined for process planning, and the compact form factor supports close tool spacing on multi-station turrets. Overall, the holder’s specification focuses on reliable mechanical clamping and dimensional clarity, enabling planners and operators to select inserts and cutting parameters with confidence. Contact Metav Werkzeuge for tailored advice on Teknik Makina DCKNR 2525 holders and ensure the right configuration for workshop requirements — Metav Werkzeuge can advise on compatibility and supply directly from Emmerich Technical Data Article number: D116-1TM Manufacturer: Teknik Makina ISO designation: DCKNR 2525 Type: DCKNR for CNMG Indexable Inserts Direction: right Facts Overall length: 150 mm Shank: 25 x 25 mm Head width: 32 mm Cutting height: 30 mm Approach angle: 75° Weight: 0.44 kg Clamping screw thread: M12 Special features Suitable for CNMG 1204 indexable inserts Right-hand turning orientation ISO DCKNR 2525 toolholder design Compact form for multi-station turrets FAQ What inserts are compatible with this holder? The DCKNR 2525 clamping tool holder is compatible with CNMG 1204 indexable inserts and supports standard grades and chipbreakers suitable for turning operations. Is the holder suitable for heavy-duty turning? The holder’s 75° approach angle, compact 25 x 25 mm shank and firm clamping result in good rigidity; Teknik Makina designed this holder to perform reliably under moderate to demanding turning conditions when paired with appropriate inserts. Which direction of cut does the tool support? This toolholder is configured for right-hand turning operations, as specified in the product data. What is the SKU and who manufactures the holder? SKU D116-1TM refers to the Teknik Makina DCKNR 2525 clamping tool holder; the product is supplied by Teknik Cutting Tools and distributed via Metav Werkzeuge. What are the key dimensions to check for turret compatibility? Key dimensions include the shank 25 x 25 mm, head width 32 mm, overall length 150 mm, and cutting height 30 mm — these determine clearance and fit on turret tool posts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑compliant toolholder that delivers stable clamping for CNMG inserts and predictable chip control; its 16 mm shank height and 95° cutting angle support repeatable setups and consistent surface finish. Order the clamping holder directly via Metav Werkzeuge or consult the team for application-specific advice. PCLNL 1616 clamping holder — PCLN for CNMG indexable inserts, left‑hand The PCLNL 1616 clamping holder is designed for left‑hand turning with CNMG 1204 indexable inserts, offering a compact 100 mm overall length and robust clamping geometry for reliable machining in workshop and light production environments Left‑hand PCLN holder for CNMG inserts Secure clamp for CNMG 1204 indexable inserts 16 mm shank height, 20 mm head width 100 mm overall length, robust 95° cutting angle Stable clamping for consistent surface quality The holder’s clamping geometry is configured to secure CNMG inserts firmly, which reduces micro‑movement and vibration during cutting. This stability translates into a measurable improvement in surface finish and extended insert life, because less chatter means smaller wear rates on the cutting edge. The left‑hand orientation and the roughly 95° cutting angle also create a predictable cutting force vector, simplifying toolpath planning and helping to maintain repeatable results across batches. Exact dimensions for fast setup and interchangeability With a 16 mm shank height, 20 mm head width and 100 mm overall length, the toolholder matches common toolpost interfaces and makes replacement and indexing straightforward. The ISO designation PCLNL 1616 signals compatibility with standard clamping systems, so set‑up time is reduced and machine downtime is minimised. The specified insert compatibility (CNMG 1204) ensures that indexable inserts can be swapped quickly—keeping maintenance simple and stocking efficient for the workshop. Designed for efficient shopfloor use and low maintenance The construction prioritises easy insert seating and reliable clamping, so wear is localised to the replaceable insert rather than the whole assembly. The combination of compact form and modest weight (0.225 kg) makes the holder convenient to handle while remaining rigid under typical turning loads. By enabling cost‑effective indexable inserts and quick changes, the toolholder supports higher machine utilisation and a lower cost per component, which is particularly valuable for small batches and mixed‑series work. Contact Metav Werkzeuge today to discuss Teknik Cutting Tools’ PCLNL 1616 clamping holder for left‑hand turning and to request application guidance directly from our Emmerich team via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: P139TM Manufacturer: Teknik Makina Designation (EN): PCLN for CNMG Indexable Inserts ISO designation: PCLNL 1616 Dimensions & weight Shank height: 16 mm Head width: 20 mm Insert height: 30 mm Overall length: 100 mm Weight: 0.225 kg Cutting angle: 95° Features & compatibility For CNMG 1204 indexable inserts Left‑hand cutting direction Shank designation: H12 Suitable for PCLN insert geometry SKU: P139TM FAQ What inserts fit this holder? This holder is designed for CNMG 1204 indexable inserts and secures them using the PCLN clamping geometry specified by the PCLNL 1616 form factor. Is the holder suitable for left‑hand turning only? Yes, the toolholder is specified for left‑hand cutting direction, matching lathe setups that require left‑hand tool orientation. What are the key dimensions to check for machine compatibility? Verify the 16 mm shank height, 20 mm head width and 100 mm overall length against the machine toolpost and toolpost pocket to ensure correct fit and clearance. How does the 95° cutting angle affect machining? The approximately 95° cutting angle provides a conservative clearance and helps control cutting forces, improving stability and aiding consistent surface finish. Can this holder improve insert life? By providing secure clamping and reduced vibration, the holder contributes to more uniform wear on the insert, which can extend usable insert life in many turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precision, compatibility and secure mounting: the holder offers a 95° cutting angle, fits CNMG 1204 inserts and features a sturdy 25 x 25 mm shank for stable turning operations — order via Metav Werkzeuge or consult our specialists for specification support. Clamping holder PCLN for CNMG indexable inserts — right‑hand turning holder with 95° cutting angle Clamping holder PCLN for CNMG indexable inserts provides a compact, rigid solution for turning operations where reliable insert seating and repeatable geometry matter most. Right‑hand toolholder, 95° cutting angle Compatible with CNMG 1204 indexable inserts Shank 25 x 25 mm for secure mounting Total length 150 mm, weight 0.766 kg Reliable cutting geometry for consistent component quality The holder delivers a defined 95° approach that maintains the insert rake and clearance during machining, resulting in consistent part geometry and predictable tool life. Built to accept standard CNMG 1204 inserts, the design reduces setup complexity and allows straightforward replacement of worn tips. The rigid shank and head geometry minimise deflection under moderate cutting forces, which supports tighter tolerances and reduces rework. By choosing a holder with a known ISO designation, assembly checks and tool inventory become faster and less error prone. Secure clamping and simple integration into existing toolposts Featuring an ISO designation PCLNR 2525 and a 25 x 25 mm shank, the holder is designed for straightforward integration into industry‑standard toolposts. The clamping arrangement and screw thread specification M12 ensure firm retention of the insert seat and repeatable axial positioning after index changes. The combination of a compact head width and a total length of 150 mm keeps the tool overhang low, which reduces vibration and improves surface finish. These attributes make the unit suitable where process reliability and quick insert changes are required. Practical dimensions and workshop handling that reduce downtime With a cutting head width of 32 mm and a cutting height of 30 mm, the toolholder balances reach and stiffness for a variety of turning tasks. The measured mass of 0.766 kg supports stable handling during tool changes while being light enough for fast toolchanger cycles where applicable. Clear, standardised data simplifies toolroom logistics and inventory management: using holders that conform to familiar ISO formats shortens training time and minimises assembly errors, translating directly into improved machine uptime. Designed for repeatability and efficient production workflows Engineered for right‑hand turning operations and compatible with widely available indexable inserts, the product offers a pragmatic solution where compatibility and repeatability are decisive. The standardised interface supports rapid replacement of inserts and facilitates tool‑setting procedures, so process planners can calculate cycle times and tool cost per part with greater confidence. When repeatability is prioritised, a stable toolholder is an immediate contributor to predictable manufacturing outcomes. For tailored advice on integrating Teknik Cutting Tools' PCLN holders into production, contact Metav Werkzeuge in Emmerich for specification guidance and order support — Metav Werkzeuge is ready to assist with technical comparisons and supply. Technical data Article number: P132TM Manufacturer: Teknik Makina Designation: PCLN for CNMG Indexable Inserts ISO designation: PCLNR 2525 ECLASS: 21181004 Facts Total length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 95° Weight: 0.766 kg Cutting direction: right Special features Compatible inserts: CNMG 1204 Clamping screw thread: M12 Right‑hand orientation Robust shank for secure mounting FAQ What insert size fits this holder? The holder accepts CNMG 1204 indexable inserts; the clamping geometry is designed for that insert format. Is this a right‑hand or left‑hand holder? This is a right‑hand turning holder; the cutting direction is specified as right. What is the ISO designation for this toolholder? The ISO designation is PCLNR 2525, which indicates the shank and head geometry. What are the shank dimensions and overall length? Shank dimensions are 25 x 25 mm and the total length is 150 mm. Which thread size is used for the clamping screw? The clamping screw thread is specified as M12, matching common clamping hardware. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of secure left‑hand clamping, integrated internal coolant and compatibility with CNMG 1204 inserts to raise productivity and tool life. Order the PCLN toolholder directly via Metav Werkzeuge or consult their specialists for application guidance. Klemmhalter — PCLN toolholder for CNMG indexable inserts, left‑hand, internal coolant (Teknik Makina) A Klemmhalter designed as a PCLN toolholder for secure turning with CNMG 1204 indexable inserts, intended for left‑hand lathe operations and industrial turning tasks Left‑hand orientation for reverse turning Integrated internal coolant feed Compatible with CNMG 1204 inserts ISO PCLNL 2020 shank for easy integration Secure clamping for repeatable turning accuracy The holder’s clamping arrangement prioritises repeatability and stability: the clamping screw TH821, in combination with the U‑plate TA016‑1 and TS‑4 dowel pin, secures the CNMG 1204 insert with minimal micro‑movement. This reduces chatter and improves surface finish, which in turn lowers the frequency of rework and insert changes. The controlled clamping geometry benefits medium‑duty turning operations by keeping the cutting edge firmly located relative to the workpiece, producing predictable tool life and consistent part quality. Targeted cooling and geometry to increase throughput Built‑in internal coolant channels supply fluid directly to the cutting zone, aiding chip evacuation and lowering thermal loading on the insert. Combined with the 95° cutting angle, this promotes efficient chip flow and reliable heat management when working at higher feeds. The tool’s cutting height of 28 mm and 125 mm overall length provide a balance between reach and rigidity, while the compact 25 mm head width supports close‑tolerance turning where stable cutting conditions are essential for productivity gains. Compact, workshop‑friendly design for straightforward integration Conforming to PCLNL 2020 ISO designation and compatible with bar systems such as K12‑IKG1/8, the holder installs quickly in common toolposts and turrets. With a nominal weight of 0.428 kg and dimensions of 20 mm height and 20 mm body width, it delivers a compact footprint without compromising strength. Standard components — the TL4 locking lever, clamping screw and supplied Allen key — simplify setup and maintenance, reducing downtime during tool changes. This makes the product suitable for workshops that require a robust, production‑ready clamping solution. Select the Teknik Makina PCLN toolholder AP140TM for left‑hand turning applications with internal coolant and contact Metav Werkzeuge for tailored specification and application advice. Technical Data Article number: AP140TM Manufacturer: Teknik Makina Designation: Klemmhalter Type / English designation: PCLN for CNMG Indexable Inserts ISO designation: PCLNL 2020 SKU: AP140TM Dimensions & Weights Holder height: 20 mm Body width: 20 mm Cutting‑head width: 25 mm Cutting height: 28 mm Overall length: 125 mm Weight: 0.428 kg Cutting angle: 95° Features & Components Internal coolant: yes Cutting direction: left Suitable for inserts: CNMG 1204 Clamping screw: TH821 U‑plate: TA016‑1 Dowel pin: TS‑4 Locking lever: TL4 Allen key: 3 Allen Compatible bar: K12‑IKG1/8 FAQ Which inserts fit this toolholder? The Klemmhalter is designed for CNMG 1204 indexable inserts; the PCLN geometry secures the insert for consistent turning. Does the holder provide coolant to the cutting edge? Yes — internal coolant channels are integrated so the PCLN holder supplies coolant directly to the insert tip to improve chip control and tool life. Is this a left‑hand or right‑hand tool? This toolholder is supplied for left‑hand turning operations, configured for reverse cutting direction on lathes. What components are included with the holder? Included items and fitted components are the clamping screw TH821, U‑plate TA016‑1, dowel pin TS‑4, locking lever TL4 and an Allen key as specified. Which ISO shank does it use and how does it integrate into existing tooling? The holder follows the PCLNL 2020 ISO designation and fits bar systems such as K12‑IKG1/8, allowing straightforward integration into standard tool carousels. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of 95° cutting angle and secure clamping height for stable, repeatable turning operations; the compact overall length ensures rigidity and accessibility in confined setups. Order the tool directly via Metav Werkzeuge or consult the specialists for application matching. P144TM — PCLN turning holder for CNMG indexable inserts, left-hand, 95° approach The P144TM is a left-hand PCLN turning toolholder designed for medium-duty external turning with CNMG 1204 indexable inserts, ideal for workshops and production lathes requiring robust insert clamping and consistent cutting geometry. Left-hand PCLN holder for CNMG 1204 95° cutting angle for stable engagement Clamping height 32 mm for secure insert support 170 mm overall length for reach and rigidity Stable clamping for consistent turning quality The holder provides a secure clamping system and a defined clamping height of 32 mm, which together reduce insert movement under load and improve repeatability. This results in better surface finish and predictable tool life when machining with CNMG 1204 inserts. The specified 95° cutting angle helps maintain favourable cutting forces during external turning, translating technical geometry into measurable production advantages such as reduced vibration and fewer rework cycles. Compact length with improved accessibility and rigidity With an overall length of 170 mm and a cutting-head width of 40 mm, the toolholder balances reach and stiffness for operations in constrained setups. The moderate length keeps the tool overhang low, reducing flex and preserving cut stability — a practical benefit when working on smaller lathes or when multiple tools are mounted in the turret. The combined dimensions mean quicker set-ups and less trial cutting before achieving process-capable parameters. Compatibility and efficiency for workshop productivity Designed for CNMG 1204 indexable inserts and supplied with an ISO designation of PCLNL 3232, the holder matches common insert geometries and clamping bars (designation P12) used across industry. The unit weight of 1.429 kg and the clear left-hand orientation make tool planning straightforward for both production and repair tasks. Relying on established ISO form factors simplifies reordering and reduces inventory complexity, enabling a streamlined workflow in a production environment. For left-hand turning tasks requiring a secure CNMG clamp and a 95° approach angle, contact Metav Werkzeuge for tailored application advice and procurement of the Teknik Cutting Tools PCLN holder Technical Data Article number: P144TM Manufacturer: Teknik Cutting Tools SKU: P144TM E-class: 21181004 Facts Orientation: left Overall length: 170 mm Clamping height: 32 mm Tool width (body): 32 mm Cutting head width: 40 mm Insert compatibility: CNMG 1204 Cutting angle: 95° Insert height support: 30 mm Weight: 1.429 kg Special features ISO designation: PCLNL 3232 Compatible clamping bar: P12 Application: external turning with indexable inserts FAQ What insert type fits this holder? The P144TM is designed to accept CNMG 1204 indexable inserts and follows the PCLN holder form for correct insert seating and clamping. Is the toolholder left- or right-hand oriented? This toolholder is left-hand oriented, suitable for turning operations that require a left-hand approach. Which ISO designation describes the holder geometry? The toolholder carries the ISO designation PCLNL 3232, which indicates its shank and pocket geometry for standardised mounting. What is the overall length and how does that affect stiffness? The overall length is 170 mm; this moderate length reduces overhang and improves rigidity compared with longer holders, aiding stability in precision turning. Can this holder be used with common turret systems? Yes, the P144TM uses standard ISO dimensions and a P12 clamping bar designation, making it compatible with many turret systems that accept PCLN-style holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust, workshop-ready clamping solution that combines left-hand cutting capability, internal coolant and ISO-compatible geometry for reliable turning operations; order directly via Metav Werkzeuge or consult our specialists for application support. PCLNL 2525 clamping holder (PCLN for CNMG) — left-hand, internal coolant — Teknik Makina A PCLNL 2525 clamping holder engineered for left-hand turning with internal coolant, designed to accept CNMG 1204 indexable inserts for secure, repeatable machining. Left-hand cutting orientation Internal coolant feed-through Compatible with CNMG 1204 inserts ISO designation PCLNL 2525 Secure clamping for consistent left-hand turning The holder offers a rigid clamping interface optimised for left-hand cutting, ensuring the insert is held with minimal movement during engagement. Compatibility with CNMG 1204 indexable inserts provides familiar tooling options and predictable chip formation; the geometry and 95° cutting angle support secure insert seating and a stable cutting line. With a 25 mm holder height and an effective cutting head width of 32 mm, the design balances reach with stiffness to reduce chatter and improve surface finish. Coolant-through routing to extend tool life Integrated internal coolant directs cutting fluid close to the cutting edge, improving heat control and chip evacuation in demanding turning cycles. This direct coolant path reduces thermal load on the insert and workpiece, which can extend tool life and maintain dimensional stability during extended runs. The toolholder’s configuration also suits operations where controlled lubrication is required for consistent results and higher material removal rates. Service-friendly components for quick maintenance Maintenance is simplified by standardised auxiliary parts: clamp screw TH821, U plate TA016-1, dowel TS-4 and knee lever TL4 are easy to replace, while a 3 Allen key engagement enables straightforward setup and repeatable torque. The modular component layout reduces spindle downtime and supports quick insert changes, helping to keep production moving with minimal interruption. Compact dimensions for versatile workshop integration Measuring 150 mm overall length and weighing 0.781 kg, this clamping holder integrates into compact tool posts and larger turret systems alike. The nominal holder width 25 mm and cutting height 30 mm suit a wide range of turning applications, from light finishing to heavier profiling passes, while the ISO designation PCLNL 2525 ensures straightforward specification and stock control within existing tool inventories. Talk to Metav Werkzeuge for an application check and tailored advice on integrating Teknik Makina clamping solutions for left-hand turning with internal coolant — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: AP142TM Manufacturer: Teknik Cutting Tools ISO designation: PCLNL 2525 Compatible inserts: CNMG 1204 Facts Holder height: 25 mm Holder width: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Overall length: 150 mm Weight: 0.781 kg Cutting angle: 95° Special features Left-hand cutting orientation Internal coolant feed-through Clamp screw TH821 U plate TA016-1 Dowel TS-4 Knee lever TL4 Allen key: 3 Allen Shank designation: M12-IKG1/8 FAQ Which inserts fit this toolholder? The holder is designed for CNMG 1204 indexable inserts and accepts standard CNMG geometry in the PCLN clamping configuration. Is the coolant routed through the holder? Yes, the toolholder features internal coolant to deliver fluid to the cutting zone and support thermal control. What cutting direction is this holder for? This clamping holder is configured for left-hand cutting operations. How long is the toolholder and how much does it weigh? The toolholder has an overall length of 150 mm and a weight of 0.781 kg, making it suitable for compact and turret-mounted setups. Are replacement clamping parts standardised? Service parts are standardised: clamp screw TH821, U plate TA016-1, dowel TS-4 and knee lever TL4 are specified for straightforward maintenance and replacement. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, rigid toolholding solution that combines secure clamping and through-tool coolant for reliable turning with CNMG inserts — the product's right-hand orientation and ISO designation ensure consistent set-up and repeatable results; order directly via Metav Werkzeuge or ask the technical consultants for application advice. Clamping Holder PCLN for CNMG Indexable Inserts — Right-hand, Internal Coolant (Teknik Makina) The Clamping Holder PCLN for CNMG Indexable Inserts is a right-hand turning toolholder engineered for CNMG 1204 inserts, offering through-tool coolant and an ISO PCLNR 2525 profile for stable, repeatable machining. Right-hand turning orientation Through-tool coolant provision Compatible with CNMG 1204 inserts Increased rigidity for consistent turning accuracy The PCLN-style clamping system delivers a compact, rigid interface that reduces vibration and improves surface finish when turning. With a 25 mm holder height and a head width of 32 mm, the design concentrates mass near the cutting zone to improve stability. The ISO designation PCLNR 2525 indicates a standardised seat that facilitates quick replacement and repeatability. Weight is moderate at 0.781 kg, which assists balanced spindle dynamics while maintaining sufficient mass for dampening. These attributes combine to make the toolholder suitable for repetitive production and short-cycle setups where dimensional consistency is required. Better cooling and chip control for longer insert life Internal coolant is provided to the cutting zone, promoting effective chip evacuation and improved thermal management of the insert. The holder supports CNMG 1204 indexable inserts and is configured for a 95° cutting angle in a right-hand orientation, which helps direct chips away from the workpiece. By maintaining lower cutting temperatures and improved lubrication at the rake and flank faces, the coolant channel extends tool life and reduces the likelihood of built-up edge on challenging materials. In production terms, this translates to fewer insert changes and less unplanned downtime. Fast assembly and straightforward integration into existing toolposts Installation and changeover are simplified by common accessory references: the clamping screw TH821, U-plate TA016-1, dowel TS-4 and clamping lever TL4 are specified for secure fitment. The toolholder’s overall length of 150 mm and a holder width of 25 mm make it compatible with compact tool posts while providing adequate overhang for reach. A single 3 Allen key is used for the primary fastenings, enabling quick insert indexing and repeatable clamping torque. The documented accessory codes support procurement and maintenance planning without guesswork. For dependable right-hand turning with through-coolant capability, contact Metav Werkzeuge for tailored advice or to arrange procurement: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich; eMail: info@metav-werkzeuge.com; Tel: +49 2822 7131930 Technical data Article number: AP132TM Manufacturer: Teknik Makina Designation: PCLN for CNMG Indexable Inserts (PCLNR 2525) Facts Holder height: 25 mm Cutting head width: 32 mm Holder width: 25 mm Cutting height: 30 mm Overall length: 150 mm Weight: 0.781 kg Cutting angle: 95° Cutting direction: right Special features Compatible with CNMG 1204 inserts ISO designation PCLNR 2525 Internal coolant: yes Clamping screw: TH821 U-plate: TA016-1 Dowel pin: TS-4 Clamping lever: TL4 Allen key: 3 Allen FAQ What inserts fit this holder? The holder accepts CNMG 1204 indexable inserts and is configured for standard CNMG geometry in a PCLN clamping seat. Is coolant supplied through the holder? Yes, the toolholder features internal coolant delivery to the cutting zone for improved chip control and temperature management. What is the ISO designation of the holder? The toolholder corresponds to PCLNR 2525, which standardises the seat and simplifies replacement and alignment. Which fastening parts are required for assembly? Assembly uses the specified clamping screw TH821, U-plate TA016-1, dowel TS-4 and clamping lever TL4, with a 3 Allen key for tightening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 95° geometry, internal coolant and CNMG 1204 compatibility to secure consistent turning results with minimal setup time; order directly via Metav Werkzeuge or consult our advisors for application guidance. Klemmhalter — Teknik Makina PCLN for CNMG indexable inserts, 95° toolholder with internal coolant The Klemmhalter is a right-hand, 95° turning toolholder engineered for CNMG 1204 indexable inserts, offering coolant-fed performance for steel machining and robust clamping in production environments. 95° cutting angle for versatile turning Internal coolant supply for improved chip control Compatible with CNMG 1204 indexable inserts ISO designation PCLNR 1616, right-hand orientation Secure clamping and precise geometry for repeatable turning The holder’s 95° geometry and ISO marking PCLNR 1616 deliver a predictable approach angle that simplifies programme setup and reduces trial cuts. Fitted for CNMG 1204 indexable inserts, the body combines a compact cross-section with a sturdy clamp system including the TH818 clamping screw to ensure stable seating under intermittent cuts. This arrangement reduces insert movement and supports consistent tolerances across batches. Coolant-fed design to extend tool life and improve finishes An internal coolant channel supplies cutting fluid directly to the insert interface, improving chip control and reducing heat at the cutting edge. This targeted delivery helps to slow abrasive wear and maintain cutting performance, which in turn supports longer tool life and better surface finish on machined parts. The coolant capability is particularly beneficial when machining demanding steels or when higher metal removal rates are required. Optimised dimensions for rigidity and accessibility With a right-hand orientation and a 28 mm cutting height, the holder balances rigidity with accessibility in confined setups. The toolhead measures 20 mm in width while the shank height is 16 mm, and the overall length of 100 mm provides effective reach without excessive overhang. The compact mass (about 0.236 kg) contributes to reduced vibration and improved surface integrity in both short-run and serial turning tasks. Easy integration with standard accessories and maintenance routines Designed for straightforward machine integration, the holder mates with common components such as the TA016-1 support plate, dowel TS-4 and lever TL4, and is adjusted using a 3 Allen key. Lightweight and simple to handle, the unit allows rapid insert changes and quick clamp adjustments, helping to maintain uptime in busy workshops and streamline routine maintenance within production schedules. Discuss Teknik Makina's PCLN toolholder with Metav Werkzeuge for tailored application advice or to arrange delivery from our Emmerich centre on +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: AP129TM Manufacturer: Teknik Cutting Tools Brand: Teknik Makina ISO designation: PCLNR 1616 Facts Weight: 0.236 kg Overall length: 100 mm Holder height: 16 mm Head width: 20 mm Cutting height: 28 mm Cutting angle: 95° Cutting direction: Right Special features Internal coolant: Yes Compatible inserts: CNMG 1204 Clamping screw: TH818 U-plate: TA016-1 Dowel: TS-4 Knee lever: TL4 Allen key: 3 Allen FAQ Which insert size fits this holder? The holder is specified for CNMG 1204 indexable inserts and is dimensioned to support that insert format reliably. Is the coolant routed internally? Yes, the toolholder features internal coolant to deliver cutting fluid directly to the insert area and aid chip evacuation. Can this holder be used for right-hand turning only? The toolholder is a right-hand orientation, suited for conventional right-hand turning operations in lathes and turning centres. What accessories are required for mounting? Recommended accessories include the TA016-1 support plate, dowel TS-4 and lever TL4; clamp torque and adjustments are made with a 3 Allen key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of stable clamping, broad insert compatibility and compact dimensions for reliable turning operations; order the clamp holder directly via Metav Werkzeuge or consult our specialists for application advice. PCLN Clamp Holder for CNMG Indexable Inserts — Teknik Makina PCLNL 2020, left-hand, 125 mm The PCLN clamp holder provides a left-hand turning solution for workshops and production lines, designed specifically for the secure use of CNMG 1204 indexable inserts in general machining and finishing applications. PCLNL 2020 ISO designation Compatible with CNMG 1204 inserts Left-hand cutting orientation 125 mm overall length Consistent clamping for predictable turning performance The PCLN clamp holder delivers a secure clamping geometry that stabilises the insert during cutting, reducing vibration and promoting repeatable surface quality. With a 95° cutting angle and a 30 mm cutting height, the toolholder aligns insert geometry precisely for predictable chip flow and reduced tool chatter. The holder body dimensions — 20 mm height, 25 mm head width and 20 mm shank width — are optimised to combine rigidity with compact envelope, enabling access in confined setups while maintaining cutting stability across standard turning cycles. Broad compatibility that reduces tool change complexity Designed for use with CNMG 1204 indexable inserts, the clamp holder supports widely available insert formats to simplify stocking and reduce machine downtime. The ISO designation PCLNL 2020 indicates a standardised interface for cartridge-style clamping, while the bar designation K12 identifies the compatible tool shank. The left-hand configuration suits counter-directional turning operations and is particularly useful where combined toolsets require mirrored holders. Using common inserts improves logistical efficiency and allows quick regrips or tool changes without special adapters. Workshop-ready build for reliable daily use Engineered for everyday production environments, the holder’s 125 mm overall length and modest mass (0.421 kg) deliver a balance between reach and low centrifugal load on the turret. The clamp mechanism secures inserts firmly, so replacement is straightforward while maintaining the repeatability of the cutting edge position. Material and coating data are not specified; however, the mechanical dimensions and ISO conformity make the unit straightforward to integrate into existing tool programmes and fixture layouts. The product supports efficient setup routines and consistent part tolerances across serial runs. Discuss specific machine fitment and order through Metav Werkzeuge — Metav’s consultants provide tailored advice from Emmerich to ensure the right toolholder choice for each turning application Technical data Article number: P140TM Manufacturer: Teknik Makina Core dimensions & mass Overall length: 125 mm Cutting height: 30 mm Holder height: 20 mm Head width: 25 mm Shank width: 20 mm Weight: 0.421 kg Cutting angle: 95° Cutting direction: left Compatibility & designation Suitable for CNMG 1204 indexable inserts ISO designation: PCLNL 2020 Bar designation: K12 Application: turning / clamping for indexable inserts FAQ What insert type does this holder accept? The clamp holder is specified for CNMG 1204 indexable inserts and is designed to maintain the correct cutting geometry for that insert format. Is this holder for left- or right-hand turning? This toolholder is a left-hand configuration, suitable for counter-directional turning operations. What are the key dimensions to check for turret compatibility? Important dimensions are the overall length (125 mm), holder height (20 mm), head width (25 mm) and shank width (20 mm); verify turret clearance and toolpath before installation. How does the PCLNL 2020 designation affect interchangeability? The PCLNL 2020 ISO designation standardises the interface and clamping style, which helps with interchangeability and ensures consistent insert positioning across compatible holders. Can this holder be used with other CNMG sizes? The holder is specified for CNMG 1204; using other sizes may change cutting geometry and is not recommended without verification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Secure high-performance external turning by choosing a holder that combines firm clamping, precise geometry and straightforward compatibility with common indexable inserts; the robust design and ISO PCLNR designation support repeatable setups. Order the clamping holder directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. PCLN clamping holder for CNMG indexable inserts — PCLNR 3232 right‑hand toolholder by Teknik Makina A right‑hand PCLN clamping holder for CNMG indexable inserts engineered for secure external turning with a 95° cutting angle and stable tool engagement. Compatible with CNMG 1204 inserts 95° cutting angle for external turning Robust 32 mm toolholder height ISO designation PCLNR 3232 Consistent rigidity and repeatable clamping for turning operations The holder delivers stable clamping and defined tool geometry that reduce vibration and support consistent cutting results. Designed around the PCLNR 3232 form, the body geometry sets the insert at a 95° approach for external turning tasks, which helps maintain predictable chip flow and surface finish. The tool’s 32 mm holder height and 30 mm cutting height are selected to match standard lathe toolposts, while the reinforced head width of 40 mm gives additional moment resistance during heavier cuts. These dimensions and the precise clamp seating ensure that insert seating is repeatable from tool change to tool change, supporting higher process reliability in everyday workshop use. Faster setup and lower downtime through smart interface and handling A compact overall length of 170 mm and a clear shank designation (P12) support quick mounting and straightforward tool management on conventional toolposts. The clamping mechanism is optimised to work with CNMG 1204 inserts, so tool transitions and replacement routines remain efficient; reduced handling time contributes to higher productive uptime. At a measured weight of 1.429 kg, the holder balances robustness with manageable handling for fitment and alignment. The clear ISO designation aids logistics and procurement, simplifying ordering and spare-part matching for procurement teams and workshop managers. Application focus and safe operational practice Intended for conventional external turning applications with indexable inserts, the holder is configured as a right‑hand unit for positive cutting engagement in right‑hand turning directions. The interface and seat geometry are compatible with the widely used CNMG 1204 insert profile, allowing established insert grades to be used without modification. The design supports standard clamping procedures and predictable orientation at the tool tip, which reduces set-up errors and supports safer operation on serial production runs. For specialised requirements or unusual machine interfaces, Metav Werkzeuge’s technical documentation and advisory services can clarify fitment and best-practice assembly. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina PCLN clamping holder (SKU P134TM) and benefit from local supply and technical support provided from Emmerich Technical Data Article number: P134TM Brand: Teknik Makina Type: PCLN for CNMG indexable inserts ISO designation: PCLNR 3232 Facts Weight: 1.429 kg Overall length: 170 mm Holder height: 32 mm Cutting head width: 40 mm Cutting height: 30 mm Cutting angle: 95° Special features Compatible inserts: CNMG 1204 Cutting direction: right‑hand Shank designation: P12 FAQ What inserts fit this holder? The Teknik Makina PCLN clamping holder is designed for CNMG 1204 indexable inserts and provides the correct seating and clamping for that insert form. Is the holder right‑hand or left‑hand? This toolholder is a right‑hand unit; it is intended for turning operations with a right‑hand cutting direction. What is the ISO designation and why does it matter? The holder carries the PCLNR 3232 ISO designation, which standardises the tool geometry and simplifies compatibility checks and procurement. What are the key dimensions for machine setup? Key setup figures for the holder (SKU P134TM) include an overall length of 170 mm, holder height 32 mm and cutting head width 40 mm, all relevant when selecting a matching toolpost and clearance envelope. Can this holder be used with different CNMG insert sizes or manufacturers? The holder is specified for CNMG 1204 form inserts; equivalents from established insert manufacturers that match the CNMG 1204 geometry are generally suitable, subject to correct thickness and corner radius verification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑stability turning solution with a right‑hand PCLN profile, ISO PCLNR 1616 shank and a 100 mm overall length for efficient workshop integration. The holder’s defined geometry and 95° cutting angle deliver consistent chip control and extended insert life — order the PCLN for CNMG Indexable Inserts directly via Metav Werkzeuge or ask our consultants if needed. PCLN for CNMG Indexable Inserts — PCLNR 1616 Toolholder by Teknik Makina, right‑hand, 100 mm PCLN for CNMG Indexable Inserts is a right‑hand turning toolholder for precision metalcutting, designed to accept CNMG 1204 indexable inserts in light to medium turning operations Right‑hand PCLN toolholder for CNMG ISO PCLNR 1616 shank 16 x 16 mm 100 mm overall length, compact design 95° cutting angle for stable turning Stable clamping for predictable turning results The PCLN geometry is engineered to secure CNMG 1204 inserts with a rigid clamping action that reduces vibration and improves surface finish. With a defined 95° cutting angle, the holder directs cutting forces into the toolpost, helping to maintain tool life and repeatability in series production. The combination of reliable clamping and a compact profile supports higher cutting parameters while preserving insert integrity, which translates into fewer tool changes and more productive machining cycles. Precise dimensions that simplify setup and balancing The holder features a 16 x 16 mm shank (ISO designation PCLNR 1616) and a 20 mm cutter‑head width, giving a compact footprint and straightforward toolpost integration. At an overall length of 100 mm and weighing 0.225 kg, the component is balanced for reduced overhang and easier setup on lathes with limited clearance. These measurable values enable predictable tool offsets and rapid replacement, so machine set‑up times are minimised and process stability is improved. Compatibility and operational flexibility for typical turning tasks Designed specifically for CNMG 1204 indexable inserts, the holder accepts commonly available insert grades for finishing or semi‑finishing. The toolholder is specified for right‑hand cutting direction and is identified by the bores/bar designation H12, supporting standard mounting routines on compatible toolposts. This compatibility makes it a practical choice across workshops that run mixed batches and need a dependable indexable‑insert solution without complex adaptations. Built for workshop reliability and supply confidence Produced by Teknik Makina, this toolholder pairs practical engineering with everyday workshop requirements: clear ISO designation (PCLNR 1616), defined cutting geometry and compact dimensions ensure predictable results. Delivered through Metav’s European supply chain, customers benefit from a quality filter based in Emmerich that supports timely availability and consistent product standards. The design focuses on operational efficiency and long‑term reliability rather than unnecessary complexity. For tailored advice on integrating the Teknik Makina PCLN for CNMG Indexable Inserts into existing tooling setups, contact Metav Werkzeuge in Emmerich for direct support and reliable supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: P129TM Manufacturer: Teknik Makina Designation: PCLN for CNMG Indexable Inserts ISO designation: PCLNR 1616 SKU: P129TM Facts Shank height × width: 16 × 16 mm Cutter‑head width: 20 mm Cutting height: 30 mm Overall length: 100 mm Weight: 0.225 kg Cutting angle: 95° Cutting direction: right Special features For CNMG 1204 indexable inserts Right‑hand turning orientation Compact, balanced design Boring bar designation H12 FAQ What inserts fit this holder best? The PCLN for CNMG Indexable Inserts (Teknik Makina, SKU P129TM) is designed to accept CNMG 1204 indexable inserts, making it compatible with standard CNMG insert grades for finishing and semi‑finishing. Is this a right‑hand or left‑hand holder? This toolholder is specified as a right‑hand toolholder; the PCLN for CNMG Indexable Inserts from Teknik Makina (SKU P129TM) is intended for right‑hand cutting direction only. What are the shank dimensions and ISO code? The holder has a 16 × 16 mm shank and is designated PCLNR 1616 according to ISO, as indicated for the Teknik Makina PCLN for CNMG Indexable Inserts (SKU P129TM). How does the 95° cutting angle influence machining? A 95° cutting angle provides a stable cutting geometry that channels forces into the toolpost, improving surface finish and insert life when using the Teknik Makina PCLN for CNMG Indexable Inserts (SKU P129TM). Is the holder suitable for compact lathes with limited overhang? Yes — with an overall length of 100 mm and a modest weight of 0.225 kg, the PCLN for CNMG Indexable Inserts (Teknik Makina, SKU P129TM) is suited to applications where a compact toolholder is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust clamping, compatibility with CNMG 1204 indexable inserts and a 95° cutting angle to secure stable left‑hand turning operations; order the toolholder directly via Metav Werkzeuge or consult the technical team for application guidance. PCLNL 2525 clamping toolholder – PCLN for CNMG indexable inserts, left‑hand, 95° cutting angle (Teknik Makina) A compact yet sturdy PCLNL 2525 clamping toolholder designed for left‑hand turning with CNMG 1204 indexable inserts, suitable for precision and series turning where stability matters Secure clamp for CNMG 1204 inserts 95° cutting angle for deep turning 150 mm overall length, M12 mounting Consistent results through precise clamp geometry The holder is engineered for rigid clamping and repeatable set‑ups, which reduces vibration and tool deflection during turning operations. Compatibility with CNMG 1204 indexable inserts ensures a familiar insert geometry for toolrooms and production lines, while the 95° cutting angle supports deeper shoulder and contouring work by keeping the insert edge in an optimal engagement position. These design choices translate directly into more uniform surface quality and fewer interrupted cycles, supporting a leaner machining process with predictable outcomes. Faster set‑up and proven workshop dimensions Standardised dimensions simplify toolholder changeover and drawer organisation: the 150 mm overall length pairs with the ISO designation PCLNL 2525 and an M12 mounting thread for secure attachment to the tool post. The compact footprint and a mass of 0.766 kg provide a balance between rigidity and manoeuvrability, making the holder suitable for both single‑piece flows and automated turret stations. Clear, documented dimensions shorten set‑up time, lower the risk of errors and support process stability in multi‑shift environments. Optimal insert handling and process advantages Using indexable inserts with this clamping design reduces downtime and tooling costs because inserts can be rotated or replaced without regrinding. The holder’s geometry, including a cutting head width of 32 mm and a cutting height of 30 mm, is chosen to support secure seat engagement and accurate chip formation. The result is improved tool life and consistent chip evacuation, which together enhance productivity and make the machining process more cost‑effective over time. For operations seeking predictable cycle times, a well‑matched holder and insert combination is a pragmatic efficiency measure. Procurement confidence and supply continuity from Metav Sourcing the right toolholder is as much about product specification as about reliable supply. Metav combines decades of metrology and tooling expertise with a broad catalogue, giving access to tested components and dependable logistics. The combination of technical competence, a wide product range and a transparent supply chain supports uninterrupted production planning and reduces administrative overhead. For workshops aiming to consolidate suppliers while maintaining precision standards, this clamping toolholder is an efficient addition to a centralised tooling strategy. For secure left‑hand turning with CNMG 1204 indexable inserts, contact Metav Werkzeuge for technical advice and reliable supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: P142TM Manufacturer: Teknik Makina Facts Overall length: 150 mm Holder height: 25 mm Holder width: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 95° Weight: 0.766 kg Special features ISO designation: PCLNL 2525 Suited for CNMG 1204 indexable inserts Left‑hand cutting direction Mounting thread: M12 Design: PCLN for CNMG indexable inserts FAQ Which insert size fits this toolholder? The holder accepts CNMG 1204 indexable inserts and is configured to provide the correct seating and clamping for that insert form factor. Is the toolholder suitable for left‑hand turning only? Yes, the clamping geometry and orientation are specified for left‑hand turning applications. What mounting connection is required for installation? The holder uses an M12 mounting thread and standardised ISO dimensions for secure attachment. How does the 95° cutting angle affect machining? A 95° cutting angle allows more aggressive shoulder cuts and better access in deep turning tasks while maintaining edge engagement and surface integrity. Can this holder be used in automated turret machines? The compact 150 mm overall length and standardised mounting make the holder compatible with many turret and gang tool installations, provided the machine accepts the ISO interface. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com