Gibt es einen Online Shop TEMU Germany?

Take advantage of the combination of ultra-fine resolution, a compact carbide probe tip and a rotatable digital display for reliable, repeatable small-range measurements; the device arrives ready for workshop use in a transport case. Order the Digital Fine Probe directly via Metav Werkzeuge or ask our consultants if needed. Digital Fine Probe M208.003.1 — compact digital probe with 0.001 mm resolution (Metav IndustryLine) The Digital Fine Probe M208.003.1 is a compact digital displacement probe intended for high-resolution comparative measurements and setup tasks in inspection and workshop environments 0.001 mm resolution readout ±0.5 mm measuring range Carbide ball probe Ø2 mm Rotatable digital display with run bar Exceptional metrological performance for small-range inspections The finely tuned measurement chain delivers a resolution of 0.001 mm combined with a specified accuracy of 0.02 mm, making the instrument suitable for precision checking of small features and positional adjustments. The limited measuring range of ±0.5 mm is deliberately matched to tasks where short-travel, low‑compliance sensing gives the best reproducibility; this translates directly into faster setup checks and fewer reworks on production or inspection benches. The data‑centred design emphasises measurable benefits: consistent repeatability and clear numerical evidence for quality control decisions. Fast, intuitive operation to reduce cycle time Operation is simplified by a rotatable digital display with MODE, SET and DATA keys and a visual run bar, allowing readings to be oriented to the operator and logged when required. Multiple measurement modes (standard, maximum, minimum and difference) provide immediate analytical value without additional calculation steps, and the automatic reversal of measuring direction prevents misreads when the probe motion changes. The probe head is equipped with a carbide ball of Ø2 mm for reliable contact with small radii and delicate surfaces, enabling precise point contact with minimal marking and excellent wear resistance. Robust packaging and workshop applicability With a compact probe length of 15 mm and a construction optimised for repeated tactile use, the instrument integrates well into bench fixtures and test rigs while remaining easy to handle during manual checks. Delivery includes a secure transport case for safe handling between job sites and storage, which preserves instrument alignment during transit. Supplied by Metav Werkzeuge, the unit is aimed at workshops and inspection labs seeking high-resolution diagnostic capability without complex integration—an accessible precision tool that supports efficient quality workflows. For workshop-ready high-resolution checks, request the Digital Fine Probe M208.003.1 from Metav Werkzeuge and discuss system suitability with our consultants via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M208.003.1 GTIN: 4061905053573 Eclass: 21170333 Label: Digital fine probe, ±0.5 mm, 0.001 mm reading Facts Measuring range: ±0.5 mm Resolution: 0.001 mm Accuracy: 0.02 mm Length: 15 mm Digital: yes Special features Digital display with MODE, SET and DATA keys and run bar, freely rotatable Probe tip fitted with carbide ball Ø2 mm Measurement modes: standard, maximum, minimum, difference Automatic reversal of measuring direction Supplied in a transport case FAQ What is the smallest increment the probe will show? The display on the Digital Fine Probe M208.003.1 indicates increments of 0.001 mm, suitable for fine comparative measurements. Which measurement modes are available on the instrument? The unit supports standard, maximum, minimum and difference modes, enabling immediate on‑screen comparison without external calculation for the M208.003.1. Is the probe tip suitable for small radii and delicate surfaces? Yes — the probe is supplied with a carbide ball probe of Ø2 mm, providing reliable point contact with good wear resistance for small features. Can the readout be oriented for different working positions? The rotatable digital display with MODE/SET/DATA keys and a run bar allows the readout to be turned for ergonomic viewing and convenient logging. Does the delivery include protective packaging for transport? The instrument is supplied in a secure transport case to protect alignment during handling and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise comparative measurement with a compact, workshop‑ready instrument: the combination of a ±0.9 mm measuring range, a 0.01 mm graduation, and a rotatable bezel supports fast setup and repeatable checks on jigs, fixtures and production parts. Order the gauge directly via Metav Werkzeuge or consult the specialists for application advice. M208.042 Dial Comparator (Ø56 mm) by Metav IndustryLine — ±0.9 mm, 0.01 mm graduation The M208.042 is a compact dial comparator designed for comparative inspection and run‑out checks in machining and quality control environments, offering a Ø56 mm rotatable dial and workshop‑grade performance. ±0.9 mm measuring range, 0.01 mm graduation 56 mm rotatable dial bezel for quick alignment Robust metal housing, lightweight 0.192 kg Reliable small‑range measurement for rapid quality checks The instrument delivers a ±0.9 mm measuring range with a clear 0.01 mm graduation, making it well suited to short‑stroke comparative tasks such as roundness checks, run‑out inspection and fine adjustment of fixtures. The fine graduation allows standard workshop verification with immediate visual feedback, reducing setup time and enabling quicker decision‑making on the shop floor. Using a dial comparator in this range shortens inspection loops and supports consistent process control. Durable design tailored to workshop handling A metal housing shields the movement from shocks and contamination while keeping the overall weight to just 0.192 kg, so the gauge remains easy to handle during repetitive checks. The 56 mm rotatable bezel permits rapid dial alignment without changing the measuring position, simplifying readings in confined setups. The instrument is built to a workshop standard, combining practical robustness with the clarity required for everyday inspection tasks. Practical mounting and integration with inspection rigs The comparator accepts a standard Ø8 mm stem mount, making it compatible with most magnetic bases and test stands used in production and maintenance. Its compact dial and proven mechanics support straightforward integration into measurement fixtures, where the instrument serves as a reliable visual amplifier of small displacements. The product is identified as a dial comparator suitable for comparative and control measurements in machine shops and inspection benches. For application support or to request a specification confirmation for the M208.042, contact Metav Werkzeuge — our Emmerich specialists provide tailored advice and order processing for workshop and industrial customers. Technical data Article number: M208.042 GTIN: 4054469104041 Customs tariff number: 90178090 Facts Measuring range: ±0.9 mm Graduation / resolution: 0.01 mm Display reading: 0.01 mm Weight: 0.192 kg Stem mount: Ø8 mm Dial diameter: 56 mm Applicable standard: workshop standard Special features Metal housing Rotatable dial via outer bezel Ø56 mm Compact design for bench and fixture use Category: dial gauges FAQ What measurement tasks is this comparator best suited for? The M208.042 dial comparator is intended for short‑stroke comparative measurements such as run‑out checks, fixture setting and small component inspection in machine‑shop and quality‑control applications. What level of reading resolution and repeatability does it provide? The instrument offers a 0.01 mm graduation, giving clear, repeatable visual readings suitable for standard workshop quality control and quick inspection tasks. How is the comparator mounted for shop use? The comparator accepts a Ø8 mm stem mount, compatible with common magnetic bases and test stands, allowing easy installation on benches and fixtures. Does the M208.042 include a protective housing and easy dial alignment? Yes. A metal housing protects the mechanism and the 56 mm rotatable bezel enables quick dial orientation without moving the measuring point. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

The combination of inductive differential sensing and a linear ball‑bearing guide delivers repeatable, low‑force displacement measurement for inspection and setup tasks; benefit from the compact ±2 mm range and included 2 m connection cable for straightforward integration. Order the probe directly via Metav Werkzeuge or consult our specialists for system compatibility. Messtaster M301.041 — Inductive measuring probe with linear ball‑bearing guide (Metav IndustryLine) A Messtaster M301.041 is an inductive measuring probe designed for fine displacement sensing in workshop inspection, gauging fixtures and machine setup tasks, offering a compact ±2 mm sensing range and low measuring force for minimal part loading. Inductive differential sensing for stable output Linear ball‑bearing guide for high repeatability ±2 mm measurement range for fine displacement control Includes 2 m cable with 5‑pin DIN connector Precise, reliable sensing for repeatable inspection results The probe uses an inductive differential principle to convert minute axial movements into a stable electrical signal, making it well suited to applications where consistent repeatability is required. The design reduces susceptibility to mechanical backlash and contact wear, while the specified accuracy (0.2+3L³ µm) provides a predictable basis for traceable measurements. As a rational choice for quality assurance loops, this sensing method supports automated comparison, tool setting and component inspection where numerical stability is vital. Smooth mechanics and low part disturbance for delicate tasks Mounted with a linear ball‑bearing guide, the mechanism ensures friction‑free stroke motion and reproducible deflection paths, which is particularly important when working with small or delicate components. The measuring force <0.633 N minimises deflection of thin or lightweight parts during contact checks, preserving dimensional integrity while enabling reliable readings. The compact ±2 mm range keeps the active sensing region tight, so transitions between measured positions remain consistent and easy to interpret during routine checks. Integration-ready electrical interface and practical accessories Electrical requirements are modest, with a supply characteristic of 0.7 V, 13 kHz, and the probe is supplied with a 2 m connection cable and 5‑pin DIN plug, allowing quick wiring into common indicator amplifiers and data acquisition systems. The included cable reduces installation time and ensures a clean connection for signal transmission, supporting both manual readout and automated measurement chains. Where fixture mounting is needed, the probe’s design and mounting provisions facilitate stable attachment and repeatable positioning in inspection jigs. Contact Metav Werkzeuge for tailored integration advice on the M301.041 measuring probe and to discuss compatibility with existing test stands or measurement amplifiers Technical data Article number: M301.041 GTIN: 4054469113630 EClass: 27144044 ETIM: EC000029 TARIC/HS code: 90173000 Brand: Metav IndustryLine Core specifications Measurement range: ±2 mm Measuring force: <0.633 N Supply: 0.7 V, 13 kHz Accuracy: 0.2+3L³ µm (L in mm) Mounting / Aufnahme: 8 Special features Inductive differential sensing principle Linear ball‑bearing guide 2 m connection cable with 5‑pin DIN plug Compact design for fixture and machine integration FAQ What measurement range does the probe cover? The M301.041 measuring probe provides a sensing range of ±2 mm, suitable for fine displacement and comparative checks. Is the probe suitable for automated gauging systems? Yes. The inductive differential output and the supplied 2 m cable with 5‑pin DIN make the probe compatible with common indicator amplifiers and data acquisition interfaces for automated gauging. How does the low measuring force affect parts under test? With a measuring force below 0.633 N, the probe minimises loading on thin or delicate components, reducing the risk of elastic deformation during measurement. Can the probe be mounted in custom fixtures? The device is designed for stable fixture mounting; the mechanical guide and compact body allow repeatable placement in inspection jigs and machine set‑ups. What accuracy can be expected in practice? The specified accuracy is given as 0.2+3L³ µm (L in mm); this provides a predictable tolerance framework for integrating the probe into quality workflows and for estimating measurement uncertainty. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of a hybrid analogue-and-digital readout, automatic measurement-range reversal, and flexible power options for reliable indicator readings in workshop and laboratory setups; order the device via Metav Werkzeuge or consult our advisers for application guidance. M301.060 Indicator unit — Analogue & digital readout with automatic range reversal (Metav IndustryLine) The M301.060 is an indicator unit for inductive probes that combines analogue trend display with precise digital measurement for comparative and position-control tasks in industrial metrology. Analogue and digital readout Automatic measurement-range reversal Resolution 0.0001 mm Battery or external power supply Fast decisions through hybrid readout The hybrid analogue and digital display delivers the best of both worlds: the dial-like analogue trace allows immediate recognition of trends and deviations, while the digital readout provides exact values for documentation. With a display resolution of 0.0001 mm, repeatable readings are straightforward and inspection protocols are easier to fulfil. This combination reduces interpretation time during set-up and series checks, making routine comparator and probe‑based measurements more efficient and less error‑prone. Continuous measurement and robust signal handling Automatic measurement‑range reversal maintains continuous indication when the probe passes zero or crosses measurement limits, eliminating manual range changes and minimising interruption during runs. The device supports a measurement range of ±2 mm and features a sensitivity of 0.7 V/V/mm, ensuring a stable output from standard inductive sensors. Power is provided by 3× LR06 batteries or via an external supply; the unit operates with an excitation frequency in the range of 13 kHz, supporting consistent signal energy for reliable probe excitation. Workshop-ready compatibility and practical benefits Designed for integration with inductive messtaster systems, this display unit is also specified as suitable for third‑party calipers of similar construction (for example, TESA types), which simplifies retrofits and replacements in existing test rigs. The compact design and clear indication make it appropriate for both bench inspection and fixture‑mounted measurement tasks. For users seeking dependable comparative measurement and straightforward installation, the device supports faster set-ups and reduces cycle times in quality control workflows. Contact Metav Werkzeuge in Emmerich for application advice, calibration options and to arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M301.060 GTIN: 4054469113647 ECLASS: 21170401 Category: Messuhren Manufacturer: Metav IndustryLine Facts Measurement range: ±2 mm Resolution (display): 0.0001 mm Sensitivity: 0.7 V/V/mm Excitation: 13 kHz Power: 3× LR06 or external supply Tariff code: 90173000 Special features Analogue and digital indication Automatic measurement-range reversal Compatible with inductive probes Suitable for third‑party calipers of the same design FAQ What is the measurement range and resolution of this indicator unit? The indicator unit offers a measurement range of ±2 mm with a display resolution of 0.0001 mm, suitable for fine comparative and position measurements. Can this device power from mains or only batteries? The device runs on 3× LR06 batteries or via an external power supply, allowing flexible use in bench or fixed applications. Is the display compatible with probes from other manufacturers? Yes, the unit is specified as suitable for inductive probes and can be used with third‑party calipers of a similar construction (for example, TESA types). What advantage does the analogue indication provide alongside the digital readout? The analogue trace gives immediate visual feedback on trends and deviations, while the digital readout supplies precise numerical values for documentation and decision‑making. Does the unit support continuous measurement across zero or range limits? Yes, automatic measurement‑range reversal ensures continuous indication when the probe crosses the zero point or measurement limits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of consistent ±8 N force application and a low inertial mass for faster, more reproducible inline checks; order directly via Metav Werkzeuge or consult the team for integration advice. Force adapter for digital calipers M401.041 — ±8 N roller accessory (Metav IndustryLine) The force adapter for digital calipers M401.041 is an accessory that applies a controlled rolling force to a caliper jaw, designed to standardise contact pressure during comparative and serial measurements with digital calipers. Precise ±8 N measuring force Compatible with thumb‑roller calipers Lightweight — only 28 g Consistent contact pressure for repeatable measurement results A controlled contact force reduces operator‑dependent variability; the ±8 N specification ensures a uniform load that stabilises the measurement interface. By converting manual thumb pressure into a defined rolling force via the integrated roller, the accessory improves repeatability in production inspection and end‑of‑line checks. This stabilisation shortens decision cycles and lowers the rate of false rejects by making each contact between jaw and workpiece more consistent. Easy retrofit and minimal influence on handling Integration requires no complex setup: the adapter mounts to calipers with a thumb‑roller interface and keeps the original handling characteristics intact. The very low mass (approx. 28 g) means negligible added inertia, so short measuring strokes and tactile feel remain virtually unchanged. Compatibility with standard digital calipers allows existing instruments to be upgraded for force‑controlled measurements without replacing the measuring device, improving throughput while keeping investment low. Practical benefits for inspection and serial testing Using a dedicated force accessory speeds up repetitive measuring tasks by removing the need for operator training on applied pressure. The roller design preserves surface finish and prevents point loading on delicate parts while delivering a consistent contact condition for each cycle. Supplied as an accessory from Metav IndustryLine, the unit supports efficient workflows in workshop, toolroom and small‑scale production environments where reliable, repeatable contact force is required. For advice on fitting the adapter or to order the M401.041, contact Metav Werkzeuge GmbH in Emmerich — info@metav-werkzeuge.com or +49 2822 7131930 — the Metav team will assist with integration and delivery options Technical data SKU: M401.041 GTIN: 4054469143651 Weight: 0.028 kg Tariff number: 90178090 Category: Accessory for measuring instruments Core measurements Measuring force: ±8 N Mass: 0.028 kg eCl@ss: 21160592 Special features Roller for consistent contact Compatible with digital calipers with thumb roller Accessory for serial and comparative measurement FAQ How does the adapter ensure consistent measurement force? The adapter applies a defined ±8 N rolling force through its roller mechanism, so each contact is made with reproducible pressure, reducing operator influence on readings. Can it be fitted to any digital caliper? The adapter is designed for calipers that use a thumb roller for jaw actuation; the M401.041 fits standard thumb‑roller interfaces used on many digital calipers. Does the adapter affect measurement speed or handling? The low mass (approx. 28 g) adds minimal inertia, preserving normal handling and allowing quick, repeatable measuring cycles without perceptible slowdown. Is the accessory suitable for delicate surface finishes? Yes, the roller distributes contact pressure and avoids point loading, helping to protect delicate surfaces while maintaining consistent contact conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of straightforward thread conversion together with a compact flange form and low mass for reliable fixture adaptation in metrology and workshop applications; order the adapter directly via Metav Werkzeuge or request advice from our consultants if clarification is needed. Thread adapter M8 to M10, Ø 24 mm, 15 mm thickness — Metav IndustryLine Thread adapter M8 to M10, Ø 24 mm, 15 mm thickness provides a simple, robust solution for converting an M8 threaded fixing into an M10 mounting point, ideal for adapting existing fixtures and measuring accessories. Thread adapter M8 to M10 Ø 24 mm compact flange 15 mm thickness for stable mounting Lightweight — 0.2 kg Convert existing fixings without reworking components A dedicated thread adapter simplifies the transition from an M8 fixing to an M10 thread, eliminating the need for re-machining or new tapped holes. The compact Ø 24 mm flange concentrates clamping forces close to the fixing point, which supports consistent seating and repeatability during fixture changes. This conversion is particularly valuable in metrology environments where maintaining datum positions and minimising setup time are essential for production throughput and inspection consistency. Compact geometry that supports stable mounting and repeatable measurement The adapter’s 15 mm thickness and reduced overhang contribute to mechanical stability, helping to keep the mounted element aligned under lateral load. With a mass of 0.2 kg, the component adds minimal inertia to assemblies while still providing a robust interface between different thread standards. These attributes reduce the risk of micro-movements that could otherwise compromise dimensional checks, so the adapter assists in preserving precision throughout repeated tool or gauge changes. Practical inventory management and operational efficiency Standardising on a small range of adapters decreases the variety of specialised fastenings and fixtures in stock, yielding a measurable efficiency gain in procurement and faster changeovers at the bench. The simple function of the adapter—converting M8 threads to M10—offers a cost-effective route to reuse high-value accessories and measuring heads that would otherwise require bespoke adaptors or replacements, supporting lean workshop practices and shorter machine or inspection downtime. Installation guidance and inspection considerations Installation is straightforward: the adapter engages the female M10 receptacle while accepting the M8 fastener, providing a low-profile connection. As a mechanical accessory, the component does not require calibration and is intended for secure mechanical use rather than measurement certification. Regular visual inspection for wear or thread damage is recommended as part of routine maintenance to assure continued reliability and safe operation in industrial use. Contact Metav Werkzeuge today to discuss compatibility with existing fixtures and to order the Metav IndustryLine thread adapter M8 to M10 (SKU M206.110) for quick integration into production or inspection setups. Technical Data Article number: M206.110 GTIN: 4061905053580 Weight: 0.2 kg Dimensions: Ø 24 x 15 mm EClass: 21130112 Facts Thread sizes: M8 → M10 Flange diameter: 24 mm Thickness: 15 mm Mass: 0.2 kg SKU: M206.110 Special features Thread conversion M8 to M10 Compact flange design Low mass for minimal added inertia Reusable mechanical adapter Intended for mechanical fixing/adaptation FAQ Which thread sizes does the adapter convert? The thread adapter converts an M8 fastening to an M10 mounting point, enabling the use of M10 fixtures where only an M8 thread exists. What are the outer dimensions of the adapter? The adapter has a flange diameter of 24 mm and a thickness of 15 mm, as stated for the Metav IndustryLine thread adapter M8 to M10 (SKU M206.110). Is the adapter intended for precision measurement or does it need calibration? This adapter is a mechanical conversion accessory and does not require calibration; it is not a measuring instrument and is used to adapt threads mechanically. How much does the adapter weigh and does the mass affect fixtures? The adapter weighs 0.2 kg; the low mass minimises added inertia while providing a stable interface between thread sizes. Can the adapter be reused for multiple fixture changes? Yes, the adapter is designed for repeated use as a conversion element between M8 and M10 fixings, subject to routine inspection for thread wear. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise Shore A0 readings together with a compact, portable form factor for fast quality checks in foam production and laboratory environments; order via Metav Werkzeuge or contact our consultants for expert advice. Digital Shore Hardness Tester M208.352.N — 0–100 A0 range, digital display A compact digital Shore hardness tester Digital Shore Hardness Tester M208.352.N designed for rapid A0 hardness checks on soft materials such as foam and sponge. 0–100 A0 measuring range, 0.5 unit resolution Ball indenter R=2.5 mm with 30 mm anvil Digital display with ON/OFF, ZERO and HOLD Fast, reliable Shore A0 readings for soft materials The instrument provides a 0–100 A0 measuring range with a readable resolution of 0.5 units, allowing clear differentiation of softer polymer foams and cellular materials. The Shore A0 scale is tailored to very soft elastomers and foam products; by measuring indentation depth with a standardised indenter geometry, the device converts mechanical response into a direct hardness value, simplifying in-line checks and incoming goods inspections. The concise, numerical readout accelerates decision-making and reduces interpretation errors compared with analogue scales. Ergonomic design and straightforward operation for routine testing An ergonomically balanced housing and low weight (approx. 0.1 kg) make the instrument suited to handheld use and quick transfer between test points. The digital display includes ON/OFF, ZERO and HOLD functions for stable readings and repeatable workflows, while the ball indenter (R=2.5 mm) and anvil/stop (30 mm) ensure defined contact geometry and positioning. These design choices reduce operator influence and permit fast serial testing, helping to keep throughput steady during production checks or laboratory routines. Robust application range and practical transport solution Calibrated for Shore A0 testing with a 30° taper tip and 0.1 mm tip radius, the device is optimised for foams and sponges but also useful for other very soft materials where A0 measurements are the standard. The compact format and protective transport case allow safe storage and straightforward mobile use across workshops or inspection rooms, preserving measurement integrity during handling and transit. The combination of a standardised indenter and electronic readout supports consistent results across shifts and operators. For dependable Shore A0 testing with Metav IndustryLine quality, order the Digital Shore Hardness Tester through Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com / +49 2822 7131930 for application advice and delivery information Technical Data Article number: M208.352.N GTIN: 4054469181486 ECLASS: 21170518 Weight: 0.1 kg Measuring range: 0–100 A0 Resolution: 0.5 units Measurement method: Shore A0 Display: Digital with ON/OFF, ZERO, HOLD Facts Indenter geometry: Ball indenter R=2.5 mm Tip: Taper 30°, tip radius 0.1 mm Anvil / stop: 30 mm Suitability: Foams, sponges Special features Compact, portable housing Protective transport case included Lightweight for handheld operation Clear numeric readout for rapid decisions FAQ How accurate are the readings on this tester? The Digital Shore Hardness Tester M208.352.N delivers readings with a clear 0.5-unit resolution on the Shore A0 scale, providing repeatable results suited to production control and material checks of soft foams and sponges. Can the instrument be used outside the workshop? Yes, the lightweight design and included protective transport case make the device convenient for field checks and mobile quality inspections. What tip geometry is used for the measurements? Measurements are taken with a ball indenter (R=2.5 mm) and a tapered tip of 30° with a 0.1 mm tip radius, matching standard requirements for Shore A0 testing. Is the device suitable for all foam types? The tester is optimised for a wide range of soft foams and sponges; for very unusual or composite materials, consult our technical team for guidance on test suitability and procedure. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of accurate Shore A measurement and simple digital operation for fast material checks in production and quality control; the device’s compact tip and lightweight design keep handling consistent across repeated tests. Order the unit directly via Metav Werkzeuge or consult their specialists for application advice. Digital Shore hardness tester M208.351.N — Handheld Shore A gauge with 0–100 HA range and 0.5 HA resolution (Metav IndustryLine) The Digital Shore hardness tester M208.351.N serves as a portable solution for rapid hardness screening on elastomers and soft plastics, combining a clear display with a compact measurement tip for confined test points. Range 0–100 HA for elastomers Resolution 0.5 HA for clear readings Flat cone tip Ø0.79 mm, 35° geometry Digital display with zero and hold buttons Reliable results for process control and QA The instrument delivers repeatable Shore A readings across the 0–100 HA range, enabling consistent pass/fail decisions within production. The 0.5 HA increment on the digital display gives a clear numerical basis for statistical process control or incoming goods inspection, reducing subjective interpretation. As a handheld hardness gauge, it suits line-side quality checks where quick throughput and documented numerical values matter more than laboratory turnaround times. Designed for straightforward handling and confined test points A flat cone tip Ø0.79 mm, 35° geometry concentrates the contact area, making it practical for small test fields and moulded parts. The unit’s lightweight (0.1 kg) construction supports stable single-handed operation while limiting operator fatigue during repeated measurements. Controls include dedicated on/off, zero and hold functions, which simplify measurement routines and let teams capture transient values without additional equipment. Application compatibility and material scope Measurement is performed according to Shore A methodology and is therefore intended for rubber, elastomers and other soft plastics such as neoprene, silicone, vinyl, felt and leather. The specification favours surface-sensitive checks and comparative testing during production runs, helping to classify compounds by hardness and to identify batch deviations early in the process. Practical delivery and workshop integration The tester is supplied complete with a protective transport case, making it straightforward to store or carry between benches and production cells. The compact form factor and the clear readout integrate easily into routine inspection workflows, and the device’s simplicity supports training of shop-floor operators without a steep learning curve. For tailored technical advice or to request specification matching for the Metav IndustryLine Digital Shore hardness tester (SKU M208.351.N), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M208.351.N GTIN: 4054469162669 Tariff number: 90241040 Manufacturer: Metav IndustryLine Core measurements Measurement range: 0–100 HA Resolution: 0.5 HA Tip diameter: Ø0.79 mm Tip angle: 35° Weight: 0.1 kg Special features Measurement method: Shore A Display: digital with on/off, zero and hold Suitable for: rubber, elastomers, neoprene, silicone, vinyl, felt, leather Supplied in a protective transport case FAQ What hardness range does the tester cover? The device measures within a 0–100 HA range, suitable for most elastomers and soft plastics. What is the resolution of the readings? Readings are shown in 0.5 HA increments on the digital display for clear numerical comparison. Which materials can be tested with this Shore A instrument? The tester is intended for rubber and soft plastics, including neoprene, silicone, vinyl, felt and leather. Is the tip suitable for small test points? Yes; the flat cone tip Ø0.79 mm, 35° is designed for compact test areas and moulded features. Is a calibration certificate supplied with the product data provided? The supplied product information does not specify a calibration certificate; the data shows the standard technical specification only. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a reliable analogue readout with 1 HA resolution, a flat cone tip Ø0.79 mm and a wide 0–100 HA range for consistent Shore A testing; the built‑in drag pointer captures peak values for repeatable QA. Order directly via Metav Werkzeuge or consult our specialists for application advice. Shore hardness tester HA (0–100 HA) — analogue Shore A, flat cone tip Ø0.79 mm (Metav IndustryLine) The Shore hardness tester HA (0–100 HA) is an analogue durometer designed for rapid Shore A hardness checks on elastomers and soft plastics in production and quality control. Analogue readout, 1 HA resolution Range 0–100 HA for Shore A testing Flat cone tip Ø0.79 mm, 35° geometry Drag pointer for peak value capture Consistent, measurable Shore A results for quality control The instrument offers a clear analogue scale with 1 HA graduation, implemented for straightforward pass/fail decisions and trend tracking. The combination of a wide 0–100 HA measuring range and a compact Ø0.79 mm flat cone tip yields representative surface contact on soft materials, ensuring reproducible readings across batches. The mechanical peak capture via the drag pointer prevents missed maximum values during quick spot checks, which supports continuous production sampling without the need for electronic systems. Tip geometry and force range tuned for elastomers The geometry and force range are engineered to match the Shore A procedure: the flat cone tip, 35°, combined with a measurement force of 0.55–8.05 N, gives contact characteristics equivalent to standardised Shore A tests. This technical pairing reduces measurement scatter on compliant surfaces such as rubber, elastomers, silicone and vinyl, producing data that can be used for material acceptance or process control. The mechanical design avoids dependence on batteries, ensuring consistent force application within the instrument’s designed limits. Robust handling and material compatibility for workshop use At approximately 0.3 kg, the tester is lightweight and easy to manoeuvre for inline inspections, handheld sampling and laboratory benches. The analogue construction is inherently durable for workshop environments and requires minimal maintenance. Compatibility with a range of substrates — from leather and felt to softer plastics — makes the instrument suitable for component testing, incoming goods control and R&D hardness screening. The simple, mechanical operation facilitates rapid familiarisation for technicians and production staff. Contact Metav Werkzeuge for tailored advice on integrating this Metav IndustryLine Shore hardness tester into production workflows and for information on delivery from the Emmerich site Technical Data Article number: M208.354 GTIN: 4054469162638 Tariff number: 90241040 Manufacturer: Metav IndustryLine Weight: 0.3 kg Facts Measuring range: 0–100 HA Resolution: 1 HA Measuring force: 0.55–8.05 N Tip diameter and angle: Ø0.79 mm, 35° Measurement method: Shore A Accuracy: 2 Special features Analogue display Drag pointer for peak value capture Suitable for rubber, elastomers, neoprene, silicone, vinyl, soft plastics, felt, leather FAQ What materials can be tested with this Shore A instrument? The Shore hardness tester HA is suitable for rubber, elastomers, neoprene, silicone, vinyl, soft plastics, felt and leather; material compatibility is listed in the specifications. How is the peak hardness recorded during a test? A mechanical drag pointer records the maximum reading at the point of contact, allowing the operator to read the peak value on the analogue scale after withdrawal. Is the measuring force suitable for standard Shore A procedures? Yes — the device applies a measurement force of 0.55–8.05 N, matched to the Shore A method and the Ø0.79 mm flat cone tip for representative contact. Does the tester require batteries or electronic calibration? The unit is an analogue instrument and functions without batteries; calibration and verification follow standard metrology practice as required by the user’s quality system. Which SKU identifies this model for ordering and spare parts? Ordering and reference can be made using SKU M208.354 for the Metav IndustryLine Shore hardness tester. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take quicker, reproducible hardness readings with an analogue gauge that combines a 0–100 HC measurement range, 1 HC resolution and a peak-capture indicator; ideal for routine quality checks on compressible materials. Supplied in a protective transport case and weighing just 0.3 kg, this compact instrument suits production and incoming‑goods inspection alike — order directly via Metav Werkzeuge or consult our specialists for application advice. Shore Hardness Tester HC — Analogue hardness gauge, 0–100 HC, 1 HC resolution The Shore Hardness Tester HC is an analogue handheld instrument for fast indentation testing of soft materials such as foams and sponges in production and laboratory environments Range 0–100 HC Resolution 1 HC Drag indicator for peak readings 2.5 mm spherical indenter Reliable numeric control for compressible materials The instrument delivers a clear numeric scale across a 0–100 HC span with a reading step of 1 HC, enabling consistent acceptance decisions in routine quality control. The specified measurement force of 0.55–8.05 N together with the 2.5 mm indenter produces repeatable contact conditions; this reduces variability between operators and makes trend monitoring straightforward. As an analogue device with a mechanical peak indicator, it is particularly suited where rapid assessment and simple documentation are required. Built for foam and sponge testing in production Designed for materials that deform under light loads, the gauge matches common practice in packaging, upholstery and foam manufacturing. The spherical 2.5 mm indenter concentrates the contact in a defined area so results are comparable across batches and suppliers. Suitability for foams and sponges means the instrument supports incoming‑goods checks, process control and batch release testing without the overhead of complex set‑ups. Practical features to speed daily inspection A mechanical drag indicator captures the highest attained reading, eliminating the need for repeated observations and making single‑handed operation more effective. At approximately 0.3 kg the unit is highly portable and simple to position on samples; the compact format aids fast throughput on inspection benches. Delivery in a robust transport case protects the gauge between shifts and during transfer between production and laboratory areas. Confidence for routine quality processes Using an analogue hardness gauge with clear resolution minimises measurement uncertainty in high‑volume workflows and supports documented quality routines. The combination of defined measurement force, standardised indenter geometry and a visible peak indicator helps to reduce non‑conforming batches and enables faster corrective actions. Its straightforward operation and compact design make it an economical instrument for regular hardness checks and supplier verification. For tailored delivery and technical advice from our Emmerich facility, contact Metav Werkzeuge to discuss the Shore Hardness Tester HC and suitable supply options for production or laboratory use. Technical data SKU: M208.355 GTIN: 4054469162645 Customs tariff number: 90241040 Key measurements Measurement range: 0–100 HC Resolution / reading: 1 HC Measurement force: 0.55–8.05 N Indenter diameter: 2.5 mm Weight: 0.3 kg Display type: analogue Features and applications Drag indicator to capture peak readings Suitable for foams and sponges Measurement method: Shore A0 Supplied in transport case FAQ What material types is this tester intended for? The Shore Hardness Tester HC is specified for compressible materials and is particularly suitable for testing foams and sponges in production and incoming‑goods inspections. How precise are individual readings? Readings are given in 1 HC increments across the 0–100 HC range; the combination of defined force (0.55–8.05 N) and the 2.5 mm indenter promotes repeatable results for routine quality control. Is the instrument handheld or bench mounted? This analogue hardness gauge is a portable, handheld instrument weighing approximately 0.3 kg, designed for manual positioning on test specimens. How does the drag indicator help during testing? The mechanical drag indicator records the peak indentation value, allowing single‑operator capture of the maximum hardness reading without continuous observation. Does the device include a protective case? Yes, the gauge is supplied in a protective transport case to safeguard the instrument during storage and transfer between production and laboratory areas. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com