Deep-reach HSS-G twist drills for precision deep-hole drilling
These HSS-G twist drills to DIN 340 are long-series, ground and plain drills with a 135° split point and cross grind, designed to reach deep or hard-to-access bores and to penetrate thick workpieces with reduced risk of deviation. Their elongated flute geometry and ground flutes ensure reliable chip evacuation and lower the chance of chip jamming, while the 135° point with cross grind provides excellent self‑centring and reduced need for pre‑spotting. Suited for machining steels and common workshop materials, the plain (uncoated) finish helps prevent build‑up on soft or lubricious materials, delivering consistent dimensional accuracy and extended process reliability. These drills serve as a robust solution for fixture construction, maintenance and demanding deep‑hole applications where reach, repeatability and tool safety are paramount.
5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — Long HSS‑G Twist Drill, 5 mm, 135° point angle, Bright Finished, DIN 340 A Twist Drill designed for Drilling Machine use: long HSS‑G construction with 5 mm diameter and a 135° point angle for deep, precise Metal drilling. Long design for deeper or hard-to-reach holes HSS‑G ground flutes for precise metal drilling 135° point angle for harder materials like stainless steel Fully ground shank for improved concentricity Exceptional Wear Resistance and Precise Metal Cutting This long HSS‑G Twist Drill is engineered for demanding metalworking tasks. The ground flute geometry produces sharp cutting edges and high concentricity, which leads to clean, accurate holes with less runout. For the user, this translates into fewer reworks and a more consistent fit for pins or fasteners. The 135° point angle reduces initial biting on hard materials, enabling controlled engagement when machining steels up to 900 N/mm². Use in stationary setups or with appropriate cooling yields the best tool life. Designed for Deep Holes and Hard-to-Reach Positions When access is limited, the extended overall length and longer spiral length provide the reach necessary for through and deep blind holes. The long design follows DIN 340 conventions for extended drills and is especially suitable for bushings and sleeves where depth is critical. The fully ground shank ensures the tool runs true in chucks and collets, improving surface finish and hole geometry. This configuration benefits machinists who need dependable performance in production and repair operations. Clear Advantages for Professional Workshops Workshops that process alloyed and unalloyed steels, cast materials, and engineering plastics will appreciate the combination of HSS‑G material and precision grinding. The ground Twist Drill requires up to 50% less feed force and can drill up to 40% faster in comparable conditions versus conventional HSS variants. For operators, that means reduced physical strain and increased throughput without sacrificing hole quality. The bright finished surface supports easy chip evacuation in many metalworking scenarios. Practical Guidance and Application Notes For best results, select appropriate spindle speed and apply cutting fluid or coolant when machining hard materials to avoid thermal stress. The 135° point angle is well suited for stainless and tempered steels, reducing the tendency to chatter during entry. Regrinding is feasible but should be performed by experienced personnel to maintain geometry; ground tools can be more brittle than rolled types and benefit from stable fixturing. If uncertain about optimal parameters for a specific material, consult technical support. Strong recommendation: Choose the MetavCUT long HSS‑G Twist Drill for deep, accurate metal drilling and contact METAV Werkzeuge for expert technical advice — 📧 info@metav-werkzeuge.com — ☎️ +49 2822 7131930 — ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 53050-FDA Diameter: 5 mm Point angle: 135° Overall length: 132 mm Spiral length: 87 mm Execution: long Colour: Bright finished Shank: Fully ground Material: HSS‑G Standard: DIN 340 Application: Drills for metal For drilling machine: Drilling Machine Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill (long HSS‑G) is primarily applied to the machining of high‑strength materials and larger drill diameters. Its ground geometry is easy to resharpen and withstands significant loads, making it suitable for deep holes and demanding Metalworking tasks. Which 3 drill types are there? The main categories are Metal drills, Wood drills and Stone/Concrete drills. Each type is optimized for material properties and cutting geometry to ensure the best drilling result.
6.5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Die Kombination aus HSS-G geschliffener Geometrie und langer Ausführung nach DIN 340 ermöglicht präzise, tiefere Bohrungen bei reduziertem Kraftaufwand; die Spirallänge von 97 mm verbessert die Spanabfuhr in schwer zugänglichen Bereichen. Bestellen Sie das Produkt direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT (Standard Line) Der Spiralbohrer von MetavCUT in langer Ausführung ist ein geschliffener HSS-G Bohrer für präzise Metallbearbeitung und tiefes Bohren im Werkstattbereich MetavCUT Spiralbohrer Standard Line HSS-G geschliffen für harte Werkstoffe Lange Ausführung nach DIN 340 für tiefere Bohrungen Spitzenwinkel 135° für schwer zerspanbare Materialien Gesamtlänge 148 mm, Spirallänge 97 mm Materialqualität und Verarbeitungsnutzen für zuverlässige Ergebnisse Das Werkstoffkonzept basiert auf HSS-G, also geschliffenem Schnellarbeitsstahl, der besonders scharfe Schneiden und hohe Rundlaufgenauigkeit ermöglicht. Diese Ausführung reduziert die Anpresskraft deutlich und beschleunigt den Vorschub, sodass Anwender bei Stahl und Guss eine höhere Produktivität erzielen. Wegen der geschliffenen Geometrie ist jedoch auf stabile Spannverhältnisse und Kühlung zu achten, um Bruchrisiken zu minimieren. Leistung und Einsatzgebiet für typische Metallarbeiten Für Bohrungen in legiertem und unlegiertem Stahl, Gusseisen, Temperguss sowie Nichteisenmetallen bietet der Bohrer durch den Spitzenwinkel von 135° bessere Anbohrwerte und geringeres Ausbrechen beim Austritt. Die längere Spirallänge von 97 mm sorgt für verbesserte Spanabfuhr bei tieferen Löchern und erleichtert den Einsatz in schlecht zugänglichen Bohrstellen. Kühlung und eine stationäre Aufnahme erhöhen Standzeit und Sicherheit. Geeignet für Werkstatt, Montage und präzise Handhabung Dieser Bohrer richtet sich an Anwender aus Werkstatt, Montage und professionellem Handwerk, die tiefe oder schwer zugängliche Bohrungen benötigen und eine Standard-Drill-Systemlösung suchen. Als 6,5 mm Bohrer liegt er im Standard-Bereich für handgeführte Maschinen und Säulenbohrmaschinen, wobei bei hoher Präzision ein Anpunkten mit Zentrierbohrer empfohlen wird. Die Verpackungseinheit von 10 Stück eignet sich für durchlaufende Anwendungen und Nachschubplanung. Besonderheiten, Praxis-Tipps und Verarbeitungshinweise Die lange Ausführung nach DIN 340 kombiniert mit geschliffener Schaftausführung erhöht die Stabilität bei tiefen Bohrungen, verlangt aber eine vorsichtige Handhabung, da geschliffene HSS-Varianten spröder sind als gewalzte Typen. Bei der Anwendung empfiehlt sich moderate Schnittgeschwindigkeit, konstante Kühlschmierung und ein kontrollierter Vorschub. Die helle Oberfläche (bright finished) erleichtert die Sichtkontrolle von Verschleiß und Spanklemmung. Empfehlung: Die MetavCUT Standard Line Spiralbohrer in HSS-G langer Ausführung ist die erste Wahl für präzises Tiefbohren in Stahl und Guss — Bestellen Sie über Metav Werkzeuge oder kontaktieren Sie uns per E‑Mail info@metav-werkzeuge.com für technische Beratung und Bestellmöglichkeiten Produktmerkmale Artikelnummer: 53065-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten Durchmesser: 6,5 mm Gesamtlänge: 148 mm Spirallänge: 97 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Schaftausführung: geschliffen Ausführung: lang (nach DIN 340) Für: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine Farbe: blank FAQ Was bedeutet die lange Ausführung beim Spiralbohrer von MetavCUT? Die lange Ausführung bei dem MetavCUT Spiralbohrer (Standard Line, SKU 53065-FDA) entspricht der DIN 340 und bietet eine verlängerte Spirallänge, die für tiefere Bohrungen und schwer zugängliche Stellen geeignet ist. Für welche Materialien ist der HSS-G Spiralbohrer geeignet? Der HSS-G Spiralbohrer von MetavCUT ist geeignet für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe. Ist der 6,5 mm Bohrer für handgeführte Bohrmaschinen geeignet? Ja, der 6,5 mm Durchmesser liegt im Standard-Bereich und ist für Handbohrmaschine und Säulenbohrmaschine geeignet; bei hoher Präzision vorher anpunkten. Warum ist der Spitzenwinkel von 135° vorteilhaft? Der Spitzenwinkel 135° reduziert das Wandern beim Anbohren in härteren Werkstoffen und verbessert das Anbohrverhalten, besonders bei Edelstahl und gehärteten Bauteilen. Wie sollte der MetavCUT Spiralbohrer eingesetzt werden, um die Standzeit zu erhöhen? Um die Standzeit des MetavCUT Spiralbohrers zu erhöhen, sollten konstante Kühlung, angepasste Schnittgeschwindigkeit und ein kontrollierter Vorschub verwendet werden; bei stationärer Aufnahme steigt die Sicherheit gegen Bruch.
6.8mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill (Drill Bit) — 6.8 mm, 135° Point, Long Version, Bright Finished, Fully Ground, DIN 340 The Twist Drill is a long HSS‑G drill bit designed for deep metal drilling and hard-to-reach holes, featuring a 6.8 mm diameter and a 135° point for improved entry into tough materials. Long DIN 340 design for deeper holes CNC‑ground geometry for precise, clean bores 135° point angle optimised for hard metals Fully ground shank for excellent concentricity High‑performance HSS‑G for reliable metal drilling This long Twist Drill is made from HSS‑G, a ground high‑speed steel alloy engineered for performance when machining metals. The ground flute geometry yields sharp cutting edges and high runout accuracy, which produces cleaner holes and reduces burr formation. Ground bits are particularly suitable for legated and unlegated steel, cast steels, sintered iron and hard plastics, as they provide a consistent cutting profile that helps maintain hole tolerance under demanding conditions. Deep holes and limited access solved by longer design For applications requiring deeper penetration or access into recessed bores, the DIN 340 long execution offers increased overall and spiral length, allowing safe and precise drilling where standard lengths fall short. The extended spiral length improves chip evacuation in long holes, reducing the risk of jamming. Users working on housings, bores or fixture‑mounted parts will benefit from the greater reach without compromising stability during the operation. 135° point angle — faster entry in hard materials A 135° point angle reduces the tendency to wander on the workpiece and shortens the initial engagement time in hard materials such as stainless steel and tempered alloys. This geometry reduces axial thrust compared with steeper points and is therefore recommended when drilling tougher steels. When paired with appropriate coolant and steady feed, the design allows efficient progress while maintaining hole quality. Fully ground shank and bright finished surface for precision The fully ground shank ensures excellent concentricity in chucks and toolholders, resulting in precise hole positioning and reduced runout. The bright finished surface improves visual inspection and handling while minimising surface irregularities that could affect seating in collets or drill chucks. For workshop and production environments where repeatability matters, this bit supports consistent, measurable results. Practical use, care and machining tips When using this long HSS‑G bit in a Drilling Machine, apply moderate cutting speeds and continuous or intermittent coolant for best life and hole quality. The ground design can be more brittle than rolled alternatives, so avoid excessive side loads and sudden impacts. For deepest performance, secure workpieces firmly, use appropriate pilot drilling when required and monitor temperatures to prevent premature wear. Regrinding is possible but should follow original geometry to preserve the 135° point behaviour. Recommend the MetavCUT Twist Drill for demanding metalworking tasks — for tailored technical advice or to check suitability for a specific application contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 53068-FDA Diameter: 6.8 mm Point Angle: 135° Execution: long (DIN 340 long version) Finish: bright finished Shank: fully ground Spiral Length: 102 mm Overall Length: 156 mm Material: HSS‑G Application: Drills for metal / suitable for Drilling Machine Norm: DIN 340 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills by MetavCUT are primarily used for machining high‑strength materials and larger hole diameters; their form is easy to regrind and withstands greater loads, making them suitable for deep and robust metal drilling tasks. Which three drill types exist? The main categories are metal drills (such as this Twist Drill), wood drills, and stone/concrete drills.
6mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Kombinieren Sie hohe Schnittgeschwindigkeit, präzise Bohrführung und lange Ausführung für tiefe Metallbohrungen. Bestellen Sie den Spiralbohrer von MetavCUT direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT — Standard Line (HSS-G, DIN 340) Der Spiralbohrer ist eine lange Ausführung nach DIN 340 für tiefe Metallbohrungen und eignet sich besonders für legierte und unlegierte Stähle sowie Gusswerkstoffe. HSS-G geschliffen für scharfe Schneide DIN 340 lange Ausführung für tiefe Bohrungen 6 mm Durchmesser für präzise Bohrungen 135° Spitzenwinkel für harte Werkstoffe Geeignet für Handbohrmaschine Präzise Schneidgeometrie für saubere Bohrbilder Die geschliffene HSS-G-Geometrie sorgt für eine sehr scharfe Schneide und hohen Rundlauf, was saubere Bohrbilder und geringe Gratbildung erlaubt. Durch den 135° Spitzenwinkel dringt der Bohrer kontrollierter in harte Werkstoffe ein, die Anbohrung gelingt ohne übermäßiges Wandern. Das Ergebnis ist eine reproduzierbare Bohrqualität bei Stählen, Guss und Nichteisenmetallen. Lange Ausführung für schwer zugängliche Bohrstellen Mit der langen Ausführung nach DIN 340 und einer Spirallänge von 91 mm lässt sich tiefer in das Werkstück eindringen oder von innen zugänglich bohren. Diese Bauform reduziert das Risiko häufiger Werkzeugwechsel bei tiefen Sacklochbohrungen und erleichtert Arbeiten an Bauteilen mit tief liegenden Bohrzonen. Anwender profitieren von weniger Rüstzeit und besserer Erreichbarkeit der Bohrstelle. Materialwahl und Standzeit in der Praxis Der Einsatz von HSS-G bietet eine hohe Verschleißfestigkeit bei Metallbearbeitung und ermöglicht bis zu 40 % schnellere Vorschübe gegenüber ungeformten Alternativen. Für dauerhaft hohe Standzeiten empfiehlt sich die Nutzung stationärer oder kraftvoller Handmaschinen mit geeigneter Kühlung, um thermische Belastung und Bruchgefahr zu minimieren. So bleibt die Schneidleistung über mehrere Löcher hinweg konstant. Anwendungsempfehlungen für sicheres Bohren Vorbohren mit einem Zentrierbohrer kann die Querschneide entlasten, besonders bei präzisen Passungen. Für maximalen Erfolg sollte die Verwendung von Kühlschmierstoff in Betracht gezogen werden, um Spanabfuhr und Werkzeugtemperatur zu kontrollieren. Der Spiralbohrer eignet sich für den Einsatz in Handbohrmaschinen ebenso wie in stationären Säulenbohrern, sofern die Spannaufnahme und Rundlaufgenauigkeit passen. MetavCUT Spiralbohrer Standard Line für tiefe Metallbohrungen wählen und direkt bei Metav anfragen — per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Technische Daten Artikelnummer: 53060-FDA Marke: MetavCUT Serie: Standard Line SKU: 53060-FDA Daten Durchmesser: 6 mm Gesamtlänge: 139 mm Spirallänge: 91 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G (geschliffen) Norm: DIN 340 (lange Ausführung) Schaftausführung: geschliffen Ausführung: lang Für Bohrmaschine: Handbohrmaschine Farbe: blank Verpackungseinheit: 10 FAQ Was macht den geschliffenen HSS-G bei diesem Spiralbohrer besonders? Der geschliffene HSS-G des MetavCUT Spiralbohrers (Standard Line, SKU 53060-FDA) liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher in Stahl und Guss ermöglicht. Für welche Materialien ist der Spiralbohrer geeignet? Der MetavCUT Spiralbohrer Standard Line wurde für legierte und unlegierte Stähle, Temperguss, Grauguss, Sphäroguss und Nichteisenmetalle konzipiert und erreicht in diesen Werkstoffen effiziente Bohrleistungen. Wie tief kann mit diesem Bohrer sicher gebohrt werden? Dank der langen Ausführung nach DIN 340 und einer Spirallänge von 91 mm eignet sich der Spiralbohrer von MetavCUT für tiefere Bohrungen; bei sehr tiefen Löchern sind mehrstufiges Aufbohren und Kühlung empfohlen. Ist der Spiralbohrer für Handbohrmaschinen geeignet? Ja, die Ausführung des MetavCUT Spiralbohrers (Standard Line, SKU 53060-FDA) ist für den Einsatz mit Handbohrmaschine vorgesehen; auf ausreichende Spannaufnahme und Rundlaufgenauigkeit achten. Welche Spitzengeometrie hat der Bohrer und welchen Vorteil bietet sie? Der Spiralbohrer verfügt über einen 135° Spitzenwinkel, der das Anbohren in härtere Werkstoffe erleichtert und die Anlauforganisation bei Präzisionsbohrungen verbessert.
7.5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — Long HSS‑G Twist Drill, Diameter 7.5 mm, Tip Angle 135°, Bright Finished, Fully Ground Shank, DIN 340 — MetavCUT Standard Line The Twist Drill is a long‑version HSS‑G drill designed for deep, accurate metal drilling with a 7.5 mm diameter and a 135° tip angle for harder materials. Long design for deep or hard-to-reach holes 7.5 mm Diameter for precise hole making 135° Tip Angle optimised for harder steels Fully ground HSS‑G for high precision and clean holes Efficient deep-hole drilling with less effort The Twist Drill in long execution delivers a clear advantage when deeper holes or recessed bores are required. The extended overall length (156 mm) and spiral length (102 mm) allow access to poorly reachable drilling positions without extensions. Thanks to the HSS‑G material and CNC‑ground flute geometry, the bit achieves reduced feed force and up to faster material removal compared with rolled counterparts, which increases productivity on metalworking tasks while maintaining precise hole quality. Geometry and material that improve performance on tough materials A 135° tip angle reduces initial cutting load and is particularly suitable for harder materials such as stainless and tempered steels. The fully ground shank and flute geometry produce very sharp cutting edges and excellent running accuracy, resulting in cleaner, more accurate holes. The drill complies with DIN 340 long‑version standards, making it a reliable choice for professional metalworking where repeatable precision matters. For non‑specialist users: HSS‑G means High Speed Steel, ground for superior sharpness and concentricity. Practical suitability and target applications This long HSS‑G twist drill is intended primarily for Drilling Machine use on metalwork: alloyed and unalloyed steel, cast materials (including grey and spheroidal graphite cast iron), sintered iron and non‑ferrous metals, as well as hard plastics. Its construction makes it ideal for workshop tasks requiring deep, through or blind holes up to moderate diameters. The bright finished surface improves chip evacuation and visibility when aligning holes, aiding consistent results in serial production or maintenance work. Usage tips for longevity and best results For best performance with the MetavCUT long twist drill, use appropriate cutting speeds, coolant and moderate feed to avoid undue stresses; ground drills can be more brittle than rolled types and benefit from controlled machining conditions. Centering and pilot holes improve hole quality in harder materials, while occasional resharpening restores geometry — an advantage of ground HSS bits is straightforward regrinding. Always secure the workpiece and use a suitable chuck for optimal concentricity. Strongly recommended: choose the MetavCUT Standard Line Twist Drill for demanding metalworking tasks — for expert advice, technical queries or to confirm suitability call METAV Werkzeuge at +49 2822 7131930, WhatsApp +49 170 2837271 or email info@metav-werkzeuge.com Bezeichnung: Twist Drill / Spiralbohrer Marke: MetavCUT SKU: 53075-FDA Durchmesser: 7.5 mm Spitzenwinkel: 135° Ausführung: long (lange Ausführung, DIN 340) Gesamtlänge: 156 mm Spirallänge: 102 mm Material: HSS‑G Schaftausführung: fully ground (geschliffen) Farbe: bright finished Anwendung: Drills for metal / Bohrer für Metall Für Bohrmaschine: Drilling Machine (Handbohrmaschine) Modellserie: Standard Line Norm: DIN 340 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill reliably machine? The MetavCUT Twist Drill (long HSS‑G twist drill) is designed for metalworking and performs well in alloyed and unalloyed steel, cast steels, grey and spheroidal graphite cast iron, sintered iron, non‑ferrous metals and hard plastics; it is optimised for tougher materials thanks to the 135° tip. Is the MetavCUT Twist Drill suitable for deep holes and recessed bores? Yes, the long execution of the MetavCUT Twist Drill provides greater overall and spiral length for deep or hard‑to‑reach holes, making it well suited to through‑holes and blind bores where a standard‑length bit would be too short. What are twist drills used for? Twist Drills are primarily applied to the machining of high‑strength materials and for larger drill diameters. Their ground form allows easier regrinding and they withstand greater loads, making them suitable for deep holes or when access is restricted. Which three drill types exist? The three primary drill types are metal drills, wood drills and stone/concrete drills. Why are twist drills point‑sharpened? Point sharpening reduces the cross‑edge at the tip of the Twist Drill, which significantly lowers friction and required feed force while improving centring of the drill in the workpiece. Can a metal Twist Drill be used to drill wood? A metal (HSS) drill can be used in wood, but guidance and hole finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and exhibit less aggressive self‑pulling. For which drilling depths is the Twist Drill most commonly used? Solid drilling is often performed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool. Which is better, HSS or HSSE? The general belief that HSSE is categorically superior to HSS is incorrect. When choosing, assess whether the working conditions justify the higher acquisition cost of HSSE for your specific application.
7mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — 7 mm, 135° tip, long, bright finished, HSS‑G, DIN 340 The Twist Drill long HSS‑G 7 mm is built for deep metal drilling with a 135° tip, suited to hard materials and less accessible bore locations on a Drilling Machine. Long Twist Drill for deep, hard-to-reach holes HSS-G ground for faster drilling and precise holes 135° tip suited for hard materials like stainless steel Fully ground shank ensures high runout accuracy DIN 340 standard for long drill execution Faster deep drilling with reduced effort for workshop use Long execution according to DIN 340 offers clear practical benefits: the increased Spiral Length and overall length enable drilling into deeper workpieces or into recesses where standard bits fall short. Because the flute geometry is ground, the bit cuts with very sharp edges, which can result in up to 40% faster drilling and requires substantially lower feed pressure compared with conventional HSS bits. The practical effect is less operator fatigue, more consistent bore quality and a faster cycle time for repetitive metalworking tasks. Precise holes in hard materials thanks to HSS‑G and 135° tip A HSS‑G (ground high‑speed steel) blank combined with a 135° tip improves centring and reduces walking on harder substrates such as stainless steel. The ground geometry gives high Runout Accuracy and clean chip evacuation, producing more concentric and burr‑reduced holes. Users benefit from better repeatability and less post‑processing. Note that ground HSS bits can be more brittle than rolled types, so controlled feeds and appropriate coolant are advised to avoid chipping. Built for metalworking: materials and machine compatibility This long variant is intended primarily for metallic materials: alloyed and unalloyed steel, cast steels, grey and spheroidal cast iron, sintered iron, non‑ferrous metals and hard plastics. It is compatible with handheld Drilling Machines and bench drills when greater reach is needed. For drilling in steels up to the typical range of 900 N/mm² the geometry and tip angle help maintain performance while minimising chatter and deflection, delivering holes that meet machining tolerances in assembly and maintenance operations. Practical handling advice to extend service life and hole quality Because the flutes and cutting geometry are produced by grinding, re‑sharpening is straightforward and preserves cutting performance. For best results, use moderate cutting speeds, steady feed and regular cooling or lubrication to manage heat and chip formation. When drilling deep bores, peck drilling or intermittent withdrawal will improve chip evacuation and reduce risk of breakage. Store bits to avoid impact and inspect for wear before reuse to ensure continued precision. Strong recommendation: For demanding deep‑hole metal drilling choose the MetavCUT long HSS‑G Twist Drill for reliable performance; METAV Werkzeuge offers comprehensive technical advice and support — Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 53070-FDA Durchmesser: 7 mm Spitzenwinkel: 135° Ausführung: long Gesamtlänge: 156 mm Spirallänge: 102 mm Farbe: bright finished Schaft Ausführung: fully ground Material: HSS-G Norm: DIN 340 Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is this Twist Drill suitable for? The MetavCUT Twist Drill long 7 mm is suitable for metalworking tasks where deeper or less accessible holes are required; the HSS‑G ground geometry and 135° tip make it especially effective for alloyed and unalloyed steels, cast materials and hard plastics. Which three drill types exist? There are three common drill categories: metal drill bits, wood drill bits and stone/concrete drill bits; the MetavCUT Twist Drill belongs to the metal drill bit family and is optimised for that application. What is a Twist Drill used for? A Twist Drill is principally used for machining high‑strength materials and larger bore diameters; its shape is easy to re‑grind and it endures higher loads while keeping a sharp cutting edge.
8.5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Hohe Präzision durch HSS‑G und CNC‑geschliffene Geometrie, kombiniert mit der langen Ausführung (DIN 340) und dem 135° Spitzenwinkel, ermöglicht tiefe, saubere Bohrungen in Stahl und Guss. Bestellen Sie den Bohrer direkt über METAV Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 8,5 mm – MetavCUT Standard Line Der Spiralbohrer von MetavCUT ist eine lange, geschliffene Ausführung für präzise Tiefbohrungen in legierten und unlegierten Metallen. Spiralbohrer »53085-FDA« von MetavCUT Standard Line HSS‑G geschliffen für hohe Präzision DIN 340 lange Ausführung für tiefe Löcher Spirallänge 109 mm für bessere Spanabfuhr Spitzenwinkel 135° für harte Werkstoffe Höhere Effizienz durch geschliffene HSS‑Geometrie Die HSS‑G Ausführung mit CNC‑Schliff liefert scharfe Schneidenkanten und hohen Rundlauf, was sich direkt in sauberere Bohrlöcher und reduzierten Nacharbeitbedarf übersetzt. Durch den geschliffenen Aufbau sind Anbohrung und Vorschub leichter, was laut Herstelleraussage bis zu 40 % schnelleres Bohren und etwa 50 % geringere Anpresskraft gegenüber herkömmlichen HSS‑Bohrern erlaubt. Das bedeutet weniger Verschleiß an Maschine und Werkzeug sowie kürzere Taktzeiten in der Werkstatt. Passend für Standard‑Einsätze in Werkstatt und Montage Mit einem Durchmesser von 8,5 mm liegt der Bohrer im Standard‑Bereich (2,0 mm–13,0 mm) und eignet sich damit für typische Werkstattaufgaben: Bohren in Baustahl, Aluminium, Kunststoffe sowie dünnere Profile und Bleche. Die lange Spirallänge macht den Bohrer besonders geeignet für schwer zugängliche Bohrstellen und tiefe Bohrungen, wobei für hohe Genauigkeit ein Anpunkten mit Zentrierbohrer empfohlen wird. Die Geometrie erlaubt den Einsatz an Handbohrmaschinen ebenso wie an stationären Säulenmaschinen. Einsatzhinweise, Kühlung und Werkstoffempfehlung Die lange Ausführung nach DIN 340 bietet Vorteile bei tieferen Bohrungen, verlangt aber eine angepasste Arbeitsweise: Kühlung bei Stahl und Guss sowie moderate Schnittgeschwindigkeit vermeiden Überhitzung und Bruchgefahr. Der Spitzenwinkel von 135° ist ausgelegt für härtere Werkstoffe; für sehr dünnwandige oder filigrane Bauteile sind alternative Verfahren zu prüfen. Für legierte und unlegierte Stähle bis etwa 900 N/mm² liefert die Kombination aus Material und Schliff zuverlässige Ergebnisse. Für präzise Tiefbohrungen empfehlen wir den HSS‑G geschliffenen Spiralbohrer von MetavCUT; bei Fragen technischen Umfangs oder zur Einsatzabstimmung steht METAV Werkzeuge per eMail info@metav-werkzeuge.com, Telefon +49 2822 7131930 oder WhatsApp +49 170 2837271 zur Verfügung Leistungsmerkmale Bezeichnung: Spiralbohrer Artikelnummer: 53085-FDA Marke: MetavCUT Serie: Standard Line Ausführung: lang Norm: DIN 340 Daten: Durchmesser: 8,5 mm Gesamtlänge: 165 mm Spirallänge: 109 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G Schaftausführung: geschliffen Farbe: blank Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 5 Ausführung EN: long FAQ Wie tief kann mit dem MetavCUT Spiralbohrer gebohrt werden? Die lange Ausführung des MetavCUT Spiralbohrers (SKU 53085-FDA) erlaubt tiefere Bohrungen als Standardbohrer; Maßgeblich sind jedoch Bohrmaschinensteifigkeit und Kühlung, daher empfiehlt METAV Werkzeuge die Verwendung stationärer Maschinen für maximale Tiefen. Ist der Bohrer für Edelstahl geeignet? Der HSS‑G Spiralbohrer von MetavCUT ist für härtere Werkstoffe konzipiert; der 135° Spitzenwinkel verbessert das Eindringen in Edelstahl, bei höherer Härte sind reduzierte Schnittgeschwindigkeiten und Kühlung ratsam. Kann der Bohrer in einer Handbohrmaschine eingesetzt werden? Ja, der Spiralbohrer ist auch für Handbohrmaschinen geeignet, wobei bei tieferen Löchern oder hohen Vorschubkräften stationäre Aufnahme bevorzugt wird, um Rundlauf und Standzeit zu erhöhen. Welche Vorteile bietet der CNC‑Schliff gegenüber gewalzten Bohrern? Der geschliffene HSS‑G Bohrer von MetavCUT liefert schärfere Kanten und bessere Rundlaufgenauigkeit, was zu saubereren Bohrbildern und effizienter Spanabfuhr führt; das wirkt sich positiv auf Oberflächenqualität und Nachbearbeitung aus. In welchen Werkstoffen erzielt der Bohrer die besten Ergebnisse? Der MetavCUT Spiralbohrer 8,5 mm liefert besonders gute Ergebnisse in legierten und unlegierten Stählen, Gusseisen und Nichteisenmetallen; für sehr zähe oder gehärtete Materialien sollte geprüft werden, ob Vollhartmetall die wirtschaftlichere Wahl ist.
8mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — Long HSS‑G 8 mm, 135° Point, DIN 340, Bright Finished Drill Bit A Twist Drill by MetavCUT is a long HSS‑G 8 mm drill bit for drilling machines, engineered for deep, precise metal bores. Long version for deeper and hard‑to‑reach bores Fully ground shaft for high concentricity and clean holes 135° point angle optimised for harder materials Conforms to DIN 340 for consistent overall length and quality Bright finished surface for corrosion resistance and easy chip evacuation High‑performance geometry for efficient metal drilling The long HSS‑G design combines extended reach with a ground spiral that provides faster penetration and reduced required feed force compared with rolled bits. This construction is particularly advantageous when working with alloyed and unalloyed steels, cast materials and hard plastics: the fully ground flute geometry yields sharp cutting edges and excellent runout accuracy. For users who need deeper bores or access to recessed holes, the extended overall length ensures reach without compromising hole quality. Cleaner holes and better centring on tough workpieces A 135° point angle reduces walking and improves centring when entering tough materials such as stainless steel. The reduced chisel edge from the point geometry lowers friction and allows for smoother entry, meaning less burr formation and cleaner bores. When paired with appropriate coolant and moderate speeds, the bit delivers precise, repeatable results that decrease post‑processing and rework. Built for workshops and drilling machines This Twist Drill is intended for use with standard drilling machines and is specified to DIN 340, which defines the longer execution for deep drilling tasks. The bright finished surface improves chip flow and offers basic corrosion protection during storage and operation. Its characteristics make it suitable for professional machinists and maintenance workshops that require a reliable, stable standard drill for a broad range of metalworking applications. Recommendations for use and tool care To maximise tool life and performance, use coolant when machining harder alloys and observe recommended cutting speeds for HSS‑G material. Because fully ground HSS bits can be more brittle than rolled variants, avoid shock loading and prefer stationary machines or well‑supported power drills. Regular sharpening restores cutting geometry; ground bits are straightforward to regrind to maintain the original precision and cutting behaviour. For deep, precise metal drilling choose the MetavCUT Twist Drill long HSS‑G 8 mm — METAV Werkzeuge offers expert technical advice and personalised support at info@metav-werkzeuge.com or by phone at +49 2822 7131930, WhatsApp +49 170 2837271 Technical Data Bezeichnung: Twist Drill Marke: MetavCUT SKU: 53080-FDA Diameter: 8 mm Gesamtlänge: 165 mm Spirallänge: 109 mm Spitzenwinkel: 135° Material: HSS-G Ausführung: long Schaft Ausführung: fully ground Für Bohrmaschine: Drilling Machine Farbe: bright finished Norm: DIN 340 Modellserie: Standard Line Anwendungen: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill is mainly used for drilling in metal; it is especially suited for machining high‑strength materials and larger diameters where deeper or recessed bores are required. Its ground geometry allows precise holes and reliable centring even in demanding workpieces. Which three drill types are there? The main categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for that application. Why are twist drills sharpened at the tip? The tip sharpening reduces the chisel edge at the drill point, which significantly lowers friction and required feed force. As a result the MetavCUT Twist Drill centres better in the workpiece and cuts with less resistance. Can a metal twist drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal bits are easier to resharpen and typically exhibit less self‑feeding action than wood‑specific designs. At what drilling depths is the twist drill most commonly used? A twist drill is the standard tool for through‑hole drilling in solid material. For diameters up to around 20 mm and depths up to approximately 100 mm, the twist drill is the most frequently used tool; the long version of the MetavCUT Twist Drill extends this capability for deeper holes.
9.5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Spiralbohrer – HSS-G Langausführung (DIN 340) von MetavCUT Der Spiralbohrer bietet präzise Tiefbohrungen in Stahl und Gusswerkstoffe und eignet sich für anspruchsvolle Werkstatt- und Montagearbeiten mit Handbohrmaschine. HSS-G geschliffen für hohe Rundlaufgenauigkeit DIN 340 Langausführung für tiefere Bohrungen 9,5 mm Durchmesser für Standardanwendungen 175 mm Gesamtlänge mit 115 mm Spirallänge 135° Spitzenwinkel für härtere Werkstoffe Stabilität und Präzision bei tiefen Bohrungen Der geschliffene HSS-G Werkstoff sorgt für eine scharfe Schneide und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher in legierten und unlegierten Stahl ermöglicht. Durch die lange Ausführung nach DIN 340 wird die Zugänglichkeit zu tiefen Bohrstellen verbessert, ohne dass die Stabilität darunter leidet. Dieser Aufbau führt zu einer effizienten Spanabfuhr bei mittleren bis tiefen Bohrungen und reduziert Nacharbeit. Materialverträglichkeit und Leistungsprofil Der Bohrer eignet sich speziell für Stahl, Gusseisen, Temperguss, Sintereisen, Nicht-Eisen-Metalle und Hartkunststoff. Dank des 135° Spitzenwinkels wird das Anbohren harter Werkstoffe erleichtert, zugleich wird das Wandern auf der Oberfläche verringert. Die Kombination aus Material und Geometrie ermöglicht kraftsparendes Arbeiten: bis zu 40 % schnelleres Bohren und rund 50 % geringere Anpresskraft gegenüber herkömmlichen HSS-Varianten. Einsatzempfehlung für Werkstatt und Maschine Für handgeführte Akkubohrschrauber ist der Durchmesser von 9,5 mm ideal, da hier Zylinderschaft und Aufnahme gängige Standards erfüllen. Weil geschliffene Bohrer empfindlicher gegen Kerb- und Stoßbelastung sind, empfiehlt sich bei intensiver Nutzung die stationäre Aufnahme oder die Nutzung mit Kühlung. Die lange Spirallänge von 115 mm unterstützt tiefe Sacklochbohrungen, erfordert aber auf die Späne und Kühlung zu achten, um Verstopfungen zu vermeiden. Praktische Hinweise zur Anwendung Vor dem Bohren empfiehlt sich gegebenenfalls ein Anpicken oder Zentrieren, um die Genauigkeit zu erhöhen. Bei sehr tiefen Löchern ist mehrstufiges Aufbohren sinnvoll; alternativ Schrauben mit geringem Vorschub und ausreichender Kühlung verwenden. Durch die geschliffene Schaftausführung bleibt die Rundlaufpräzision auch bei wiederholtem Einsatz erhalten, was die Standzeit in der Praxis erhöht. Für wen dieses Werkzeug entwickelt wurde Der Spiralbohrer aus der Standard Line von MetavCUT richtet sich an Metallbauer, Instandhalter, Mechaniker und ambitionierte Heimwerker, die Wert auf präzise Bohrbilder und Zuverlässigkeit legen. Die Verpackungseinheit mit 5 Bohrern macht die Beschaffung für Werkstattbedarf effizient und planbar. Empfehlung: Den MetavCUT Standard Line Spiralbohrer direkt bei Metav anfragen, um Tiefbohrungen effizienter und präziser zu realisieren; bei Detailfragen steht der Metav Technikservice per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung. Produktmerkmale Artikelnummer: 53095-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Ausführung: lang Material: HSS-G Norm: DIN 340 Fakten Durchmesser: 9,5 mm Gesamtlänge: 175 mm Spirallänge: 115 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Schaft Ausführung: geschliffen Farbe: Blank (bright finished) Für Bohrmaschine: Handbohrmaschine HSS-G: geschliffen, CNC-Schliff für scharfe Kanten und hohe Rundlaufgenauigkeit FAQ Für welche Materialien ist der Bohrer geeignet? Der MetavCUT Spiralbohrer (Standard Line, SKU 53095-FDA) eignet sich für legierten und unlegierten Stahl, Gusseisen, Temperguss, Sintereisen, Nicht-Eisen-Metalle und Hartkunststoff. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die Ausführung ist für den Einsatz in Handbohrmaschine vorgesehen; bei intensiver oder sehr tiefer Anwendung ist stationäre Aufnahme und Kühlung zu empfehlen. Wie tief kann mit dem langen Spiralbohrer gebohrt werden? Die lange Ausführung mit 115 mm Spirallänge erlaubt tiefere Bohrungen, bei sehr großen Tiefen sollte mehrstufiges Aufbohren oder passende Werkzeugaufnahme verwendet werden. Welchen Vorteil hat der geschliffene Schaft? Die geschliffene Schaftausführung sorgt für bessere Rundlaufgenauigkeit und schärfere Schneiden, was zu saubereren Bohrbildern und höherer Präzision führt. Wieviele Bohrer sind pro Paket enthalten? Die Verpackungseinheit enthält 5 Stück, geliefert als Set der MetavCUT Standard Line Spiralbohrer.
9mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
MetavCUT Twist Drill — Twist Drill, 9 mm, 135° tip, Long, Bright finished, HSS‑G, DIN 340 The MetavCUT Twist Drill is a long HSS‑G Twist Drill engineered for deep, precise metal drilling in demanding applications with a 9 mm diameter and a 135° tip. Long HSS‑G Twist Drill for deep holes 9 mm diameter for precise metal drilling 135° tip for hard materials like stainless steel Fully ground shank for high runout accuracy Conforms to DIN 340 for deep hole performance High cutting performance for tough metals Designed to handle challenging materials, this long HSS‑G Twist Drill excels in drilling legierte und unlegierte Stahl grades and cast irons. The larger 135° tip angle reduces entry forces for harder workpieces and improves centring, while the long flute length allows access to recessed holes. Users benefit from faster advance and reduced effort, since the ground geometry promotes a sharper cutting edge and cleaner chip removal. Precise geometry for accurate bores A fully ground shaft and CNC‑ground flutes ensure high runout accuracy and consistently round holes, which is critical when machining components that require tight tolerances. The ground manufacturing method yields very sharp edges and precise tolerance control; however, the harder geometry is best used with appropriate feed, cooling and, for portable setups, cautious handling to avoid brittle breakage. Practical advantages in workshop and production Because the long variant follows DIN 340, it is suited for deeper bores, bushings and situations with limited accessibility. The bright finished surface aids visual inspection and reduces initial friction during entry. For metalworking tasks in small series or repair work the tool reduces rework thanks to cleaner holes, making it an efficient choice where reliability and repeatability matter most. Who benefits and how to use it safely Engineers, toolroom technicians and maintenance professionals profit from the combination of HSS‑G hardness and long design when working on automotive, mechanical and maintenance applications. When using this Twist Drill in stationary machines, apply cutting fluid and moderate speed for best life expectancy. For handheld Drilling Machines, maintain firm guidance and lower advance rates to minimise breakage risk. We recommend the MetavCUT long HSS‑G Twist Drill for demanding deep metal bores — for personalised advice, drill parameter recommendations or further technical data contact METAV Werkzeuge: info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 53090-FDA Diameter: 9 mm Total length: 175 mm Spiral length: 115 mm Tip angle: 135° Material: HSS‑G Execution: Long Colour: Bright finished Shank execution: Fully ground Standard: DIN 340 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 5 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill is primarily intended for metalworking and is applied for drilling in high‑strength and cast materials where long, stable bores are required; it is especially suitable for deep holes and hard materials. Can the MetavCUT Twist Drill be re‑sharpened and reused? Yes, the MetavCUT Twist Drill made of HSS‑G can be re‑sharpened by grinding; attention should be paid to preserving the original tip angle and flute geometry to maintain performance. For what are Twist Drills used? The MetavCUT Twist Drill is mainly used when machining high‑strength materials and larger diameters; its form is relatively easy to re‑grind and it stands up to higher loads. Which 3 drill types exist? The main categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill type. Why are Twist Drills pointed? The point grind reduces the cross‑cut at the tip of the MetavCUT Twist Drill, lowering friction and required feed forces while improving centring accuracy in the workpiece. Can you drill wood with a Twist Drill? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; metal drills are easier to re‑sharpen and have less self‑feed. At which drilling depths is the Twist Drill most used? Solid drilling for diameters up to around 20 mm and depths up to 100 mm is the most frequent use case; the MetavCUT Twist Drill is a common choice for such through‑holes and deep bores. What is better, HSS or HSSE? Choosing between HSS and HSSE depends on working conditions; the common assumption that HSSE is universally superior is incorrect — evaluate whether the application justifies the higher cost relative to the actual material and speed demands.
Reach deeper with reliable precision
The HSS-G twist drill to DIN 340 (long series), finished bright and ground with a 135° split point and cross grind is engineered for deep-hole tasks where standard drills fall short. Its extended flute length and ground profile combine to deliver precise, repeatable results in fixture making, repair work and bore positions that are difficult to access.
Why this geometry matters in practice
Long-series geometry increases reach without compromising accuracy. Ground flutes and a bright, uncoated surface ensure smooth chip flow along the extra length, while the 135° split point with cross grind provides fast self-centring and lower thrust requirements. These properties make the tool particularly suited to deep drilling in thick components and to situations where chip evacuation is critical.
Tangible production advantages
- Extended reach (DIN 340 long series) — access deep or recessed bores.
- Optimised chip evacuation — ground flutes and bright finish reduce spigot and chip build-up.
- Self-centring 135° split point — reduces or removes the need for centre punching; lowers feed force.
- Uncoated bright finish — minimises built-up edge when machining aluminium and many plastics.
- Higher process reliability — lower risk of tool breakage and fewer reworks during deep drilling.
Metav as a pragmatic sourcing choice
Sourcing the right long-series twist drill is easier with Metav. As a precision partner based in Emmerich, Metav combines decades of expertise with a broad range of measurement and workshop equipment. Over 48,000 customers trust Metav’s consistent quality and dependable supply chain, making it a sensible choice for procurement of HSS-G twist drills and related tooling.
Summary
For demanding deep-hole drilling, the HSS-G twist drill (DIN 340 long series) with bright, ground flutes and a 135° split point offers extended reach, superior chip control and reliable self-centring — a practical solution for fixture shops and repair environments.
key specifications
- Material: HSS-G (high-speed steel)
- Standard: DIN 340, long series
- Point angle: 135° split point with cross grind
- Finish: bright, ground flutes (uncoated)
- Primary applications: deep-hole drilling, thick workpieces, hard-to-reach bores, fixture construction, repair work
- Functional benefits: excellent chip evacuation; reduced built-up edge on aluminium/plastics; improved self-centring; lower thrust force
FAQ
What advantages does a long-series HSS-G twist drill offer over a standard-length drill?
A long-series HSS-G twist drill provides extended reach for deep or recessed bores and, thanks to ground flutes and a bright finish, superior chip evacuation that reduces the risk of jamming and tool breakage.
Is the 135° split point suitable for materials like aluminium or plastics?
Yes. The 135° split point with cross grind gives reliable self-centring and lower thrust; combined with the bright, uncoated finish this helps prevent built-up edge when machining aluminium and many plastics.
Do I still need to pre-centre or use a centre punch with this drill?
In most cases the HSS-G twist drill with 135° split point self-centres sufficiently to eliminate the need for a centre punch, particularly on flat or accurately fixtured workfaces.
Can these drills be used in jigs and fixtures or only in handheld drilling?
They are well suited to both fixtured drilling and machine-mounted operations; the long-series geometry is especially valuable in jigs, fixtures and repair settings where bores are deep or hard to access.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com