Durable indexable inserts for efficient metalcutting
Indexable inserts are hardened cutting elements designed to deliver consistent material removal in metalworking, providing cost-effective tool life management and repeatable results for turning, milling and drilling operations. Suited for machining steel, stainless and heat-resistant alloys, these inserts offer rapid edge renewal and reduced downtime through simple indexing, while versions optimised for internal coolant significantly improve chip control and thermal management in demanding applications. By choosing the right insert grade and geometry you gain improved tool life, predictable wear behaviour and better surface finish thanks to enhanced chip control, with key benefits including wear-resistant carbide, internal coolant compatibility and reliable chip breaking.
ADMT 17T308 T3130 Wendeplatten - Tungaloy
Benefit from the combination of T3130 wear resistance and a 0.8 mm corner radius for stable cutting and consistent surface finish; order directly via Metav Werkzeuge or consult our advisors for application guidance. ADMT 17T308 T3130 – Indexable milling insert for milling (Tungaloy) ADMT 17T308 T3130 is an indexable milling insert engineered for productive milling tasks within compatible Tungaloy tool families T3130 grade for wear resistance and toughness Parallelogram shape, 17 mm size 0.8 mm corner radius for improved finish Cylindrical hole with 40°–60° countersink Consistent machining performance through optimised grade and substrate The insert uses the T3130 grade on a carbide substrate to deliver a dependable balance of wear resistance and toughness. This combination reduces flank wear under mixed cutting conditions and helps maintain a stable cutting edge over longer tool lives, which translates into fewer interruptions for tool change and more predictable cycle times. The engineering behind the grade aims to support a wide range of milling operations while preserving edge stability under varying feed and speed regimes, so process reliability is improved without complex parameter changes. Precision geometry for improved surface quality and chip control A parallelogram form and a 0.8 mm corner radius produce a controlled engagement with the workpiece, supporting repeatable surface finishes and edge strength. The insert’s seating geometry must match the tool body to ensure correct rake and clearance; the geometry provides an 85° approach and a 15° relief angle for predictable chip formation and reduced vibration in many milling scenarios. The single-sided chipbreaker helps moderate chip thickness and evacuation, which is especially useful on interrupted cuts or varied engagement patterns, contributing to consistent part quality. Fast integration into modular milling systems and straightforward mounting Designed for use in Tungaloy milling systems, the insert features a cylindrical hole with a 40°–60° countersink to secure the insert with a clamping screw and, where required, a supporting shim. The system composition — comprising the milling body, the indexable insert, clamping screw and possibly a backing plate — ensures repeatable seating and simple replacement during maintenance cycles. Correct matching of seat, geometry and body is crucial; the modular approach enables quick insert indexing, reducing downtime and supporting higher overall equipment effectiveness. Reliable in varied milling tasks with a focus on productivity The insert is intended for face, shoulder, slot, high-feed and contour milling depending on the chosen tool family. The combination of robust substrate, T3130 coating behaviour and chip control supports stable cutting in many everyday production tasks, promoting improved throughput and tool-life consistency. For manufacturers aiming for reproducible results and low process variability, this solution provides a practical balance between performance and versatility while remaining compatible with established milling tool systems. Contact Metav Werkzeuge for application-specific selection and availability of the Tungaloy ADMT17T308 T3130 indexable milling insert and for swift technical advice Technical data Article number: 6853805 Manufacturer SKU: TUN6853805 Seller SKU: 6853805-Tungaloy Series: Indexable milling inserts Manufacturer: Tungaloy Facts Corner radius: 0.8 mm Insert size: 17 mm Plate thickness: 3.97 mm Approach angle: 85° Relief (free) angle: 15° Special features Material: Carbide Grade: T3130 Shape: Parallelogram With hole: yes Hole style: cylindrical hole + one-side countersink (40°–60°) Chipbreaker: single-sided Intended application: milling Typical uses: face, shoulder, slot, high-feed, contour milling System composition: milling body, indexable insert, clamping screw, possible shim FAQ Which milling operations is this insert suited for? The ADMT17T308 T3130 indexable milling insert is suitable for face, shoulder, slot, high-feed and contour milling when used in the matching Tungaloy tool family. What is the insert made from and what does the T3130 grade provide? The insert is made from carbide; the T3130 grade provides a balanced combination of wear resistance and toughness for extended edge stability during milling. What mounting and geometric features ensure secure clamping? Secure clamping is achieved via the cylindrical hole with a one-side countersink (40°–60°); the parallelogram form and correct seat geometry of the tool body ensure consistent rake and clearance. What corner radius and angles does the insert offer? The insert features a 0.8 mm corner radius, an 85° approach angle and a 15° relief angle to support surface finish and controlled chip formation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
ADMT 180712 Indexable Insert for Aluminium - MetavCUT
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Product features ADMT 180712 insert from MetavCUT Brand: MetavCUT Manufacturer Order Number: ADMT180712R-Aluminium ISO-Code: ADMT180712 Usage for: Aluminium Material: cemented carbide Form: parallelogram Usable to the work on: Aluminium Clearance Angle: 15° with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Thickness: 7,94mm Radius: 1.2 Chip Breaker: single-sided Angle: 85° Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-ADMT-180712-Aluminium-MetavCUT 40END
ADMT 180712 Indexable Insert for Cast Iron - MetavCUT
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com Product specifications indexable inserts ADMT 180712 from MetavCUT Brand: MetavCUT Manufacturer Order Number: ADMT180712R-CastIron Data & Figures: ISO-Code: ADMT180712 Clearance Angle: 15° Angle: 85° Thickness: 7,94mm Radius: 1.2 Special features Material: cemented carbide Usage for: Cast steel with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-ADMT-180712-Cast Iron-MetavCUT 40END
ADMT 180712 Indexable Insert for Stahl - MetavCUT
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com Detail specifications for ADMT 180712 indexable inserts from MetavCUT Brand: MetavCUT Manufacturer Order Number: ADMT180712R-Steel Facts & Figures: ISO-Code: ADMT180712 Clearance Angle: 15° Angle: 85° Thickness: 7,94mm Radius: 1.2 Features Material: cemented carbide Usage for: Steel with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-ADMT-180712-Stahl-MetavCUT 40END
ADMT 180712 Indexable Insert for Stainless Steel - MetavCUT
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Product characteristics indexable inserts ADMT 180712 from MetavCUT Brand: MetavCUT Manufacturer Order Number: ADMT180712R-Stainless Dataand Figures: ISO-Code: ADMT180712 Clearance Angle: 15° Angle: 85° Thickness: 7,94mm Radius: 1.2 Special features Material: cemented carbide Usage for: Stainless steel with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-ADMT-180712-Stainless Steel-MetavCUT 40END
ADMT 210408 AH120 Wendeplatten - Tungaloy
The PVD‑coated AH120 grade and the precise 0.8 mm corner radius deliver a balance of sharp cutting action and process stability for milling operations; the ADMT series design ensures secure clamping and predictable chip control. Order the insert directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. ADMT 210408 AH120 – Milling indexable insert by Tungaloy, parallelogram form, 0.8 mm radius ADMT 210408 AH120 is an indexable insert designed for Tungaloy milling systems, optimised for face, shoulder, slot, high‑feed and contour milling tasks. Parallelogram form for versatile milling PVD-coated cemented carbide AH120 Cylindrical hole with single-side countersink Sharp edge and process-secure performance Engineered geometry for consistent cutting performance The ADMT210408 AH120 insert combines a parallelogram plate form with a 0.8 mm corner radius and a precisely ground relief to generate a stable cutting edge that supports predictable chip formation and consistent surface finish. The PVD‑coated cemented carbide substrate provides a balance between hardness and toughness, meaning fewer interruptions for edge refurbishment. For practical terms, this geometry reduces vibration in interrupted cuts and improves repeatability across batches, which translates into higher uptime and more consistent component quality. Compatibility and secure clamping for production environments Designed for use in Tungaloy milling systems, the insert must be used with a matching seat and clamping arrangement: the system typically comprises the milling body, indexable insert, a clamping screw and, if required, a backing shim. The plate includes a cylindrical hole with a single‑side countersink (40°–60°) to ensure reliable axial and radial location, while the parallelogram shape offers cutting edge options suited to different tool families. Typical applications include face milling, shoulder milling, slot milling, high‑feed milling and contour milling, where the geometry supports flexible tool set‑ups and reduces the need for multiple specialised inserts. Durability, process security and efficient machining The AH120 grade is a wear‑ and breakage‑resistant option formulated for milling, providing a sharp cutting edge and enhanced process security in general production work. The PVD coating contributes to reduced adhesion and thermal wear, helping to extend effective tool life and maintain dimensional accuracy over longer runs. For production managers, this means fewer tool changes, lower scrap risk and improved productivity; for operators, it delivers confidence in repeatable performance and surface quality. Metav Werkzeuge can advise on matching insert geometry to the chosen milling body to maximise tool life and machining economy. Contact Metav Werkzeuge for tailored application advice on Tungaloy ADMT210408 AH120 inserts and to arrange supply or technical guidance; eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 Technical Data Article number: 6816610 SKU: 6816610-Tungaloy Manufacturer SKU: TUN6816610 Model series: Milling indexable inserts Type designation: ADMT210408 Facts Corner radius: 0.8 mm Thickness: 4.76 mm Inscribed circle / size: 21 mm Included angle: 85° Clearance angle: 15° Countersink angle: 40°–60° Special features PVD‑coated cemented carbide Grade AH120 One‑sided chipbreaker Parallelogram plate form With cylindrical hole and single‑side countersink For face, shoulder, slot, high‑feed and contour milling Requires matching seat, geometry and milling body for correct assembly FAQ What is the primary advantage of the ADMT210408 AH120 insert? The ADMT210408 AH120 insert (Tungaloy milling indexable insert, SKU 6816610‑Tungaloy) provides a sharp cutting edge with wear‑ and breakage‑resistant performance thanks to the AH120 grade and PVD coating, improving process stability in milling operations. Which milling operations suit this insert? This indexable insert is suited to face milling, shoulder milling, slot milling, high‑feed milling and contour milling, depending on the chosen milling body and assembly. How is the insert clamped in the tool body? Clamping is achieved via the cylindrical hole with a single‑side countersink; the system requires the appropriate clamping screw and, if necessary, a backing shim to match the milling body. Does the insert require a specific tool body? Yes, the insert must be used with a compatible Tungaloy milling body; seat geometry and plate form must technically match to ensure correct locating and secure clamping. What benefits does the AH120 grade and PVD coating provide? The AH120 grade offers enhanced resistance to wear and chipping during milling, while the PVD coating reduces adhesion and thermal degradation, extending tool life and maintaining cutting performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
ADMT 210408 AH140 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide AH140, precise 85° cutting geometry and a secure clamping hole for consistent, repeatable milling results; order the ADMT210408 AH140 insert directly via Metav Werkzeuge or ask the Metav Werkzeuge consultants for application advice. ADMT210408 AH140 ADMT indexable insert for milling – Tungaloy The ADMT210408 AH140 is an indexable milling insert for Tungaloy systems, designed for face, shoulder, slot, high‑feed and contour milling where a sharp cutting edge and process security are required PVD-coated carbide grade AH140 Parallelogram form with 85° cutting angle 0.8 mm corner radius for controlled edge strength Cylindrical hole with single-sided countersink (40°–60°) Longer tool life through optimised coating and grade The combination of a PVD-coated carbide substrate and the AH140 grade delivers enhanced wear resistance and reduced chipping in interrupted or medium-duty milling cycles. The coating reduces adhesive and abrasive wear on the cutting edge, which in turn extends tool life and reduces changeover frequency. For production environments this translates into greater process reliability and fewer unexpected interruptions, helping to keep cycle times stable. Geometry engineered for secure engagement and consistent finishing The parallelogram shape and 85° cutting angle provide a predictable contact geometry with the workpiece, balancing shear conditions and radial engagement. The 0.8 mm corner radius increases edge strength compared with very small radii while still allowing good surface finish; it is particularly effective where a compromise between edge robustness and fine detail is required. The insert’s single‑sided chipbreaker controls chip formation to aid evacuation and avoid built‑up edge, improving repeatability across batches. System integration, flexibility and application scope Designed as part of a full milling system, the insert must be matched with the correct insert seat, cutter geometry and clamping components for full performance. The built‑in cylindrical hole with a single‑sided countersink (40°–60°) ensures secure clamping and repeatable seating, which is essential for high‑precision operations. Typical uses include face, shoulder, slot, high‑feed and contour milling depending on the assigned cutter family; the insert therefore offers flexibility across multiple milling tasks while maintaining process security. Contact Metav Werkzeuge today for guidance on integrating Tungaloy ADMT210408 AH140 inserts into production setups and for availability details — info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 6820626 Manufacturer SKU: TUN6820626 SKU: 6820626-Tungaloy Designation: ADMT210408 AH140 Model series: Fräswendeschneidplatten Numerical data Cutting angle: 85° Corner radius: 0.8 mm Plate thickness: 4.76 mm Plate size: 21 mm Relief angle: 15° Special features Material: PVD-coated carbide Shape: Parallelogram Chipbreaker: one-sided Hole: cylindrical hole with single-sided countersink (40°–60°) Typical applications: face, shoulder, slot, high‑feed and contour milling System note: insert seat, geometry and cutter body must match FAQ Which milling operations are suitable for this insert? The ADMT210408 AH140 insert is intended for face, shoulder, slot, high‑feed and contour milling when used in compatible Tungaloy milling systems. How does the AH140 grade affect performance? AH140 is a PVD‑coated carbide grade that emphasises wear resistance and breakage control; the grade supports consistent cutting edges under typical milling loads for the specified applications. What effect does the 0.8 mm corner radius have on machining results? A 0.8 mm corner radius increases edge strength and reduces susceptibility to chipping compared with smaller radii, while still permitting a good surface finish when correctly applied. What type of clamping does the insert require? The insert features a cylindrical hole with a single‑sided countersink (40°–60°) to provide secure clamping and repeatable seating in the corresponding cutter body. Can the ADMT210408 AH140 be used in any milling body? The insert is compatible only with bodies that match the ADMT210408 seat geometry; correct matching of insert seat, geometry and cutter body is essential for safe and repeatable operation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
ADMT 210408 T3130 Wendeplatten - Tungaloy
Combine robust carbide construction, the wear-resistant T3130 grade and a precise 0.8 mm corner radius to secure reliable performance across face, shoulder and high-feed milling. Order the ADMT210408 directly via Metav Werkzeuge or contact our consultants for application advice. ADMT210408 T3130 parallelogram indexable insert for milling by Tungaloy — 0.8 mm radius, with hole ADMT210408 T3130 is an indexable milling insert designed for face, shoulder, slot and high-feed operations within Tungaloy milling systems, offering stable cutting-edge behaviour and reliable chip control. T3130 grade for wear resistance and toughness Parallelogram form for versatile milling operations 0.8 mm corner radius for precise edge definition Cylindrical hole with single-sided countersink (40°–60°) Engineered for consistent chip control and process stability The ADMT210408 combines a carbide substrate with the proprietary T3130 grade to balance wear resistance and edge stability. This balance reduces flank wear and maintains dimensional accuracy over extended tool life, which in turn improves process stability on medium to high-duty milling tasks. The parallelogram shape contributes to favourable cutting geometries for face and shoulder milling, while the single-side chipbreaker geometry supports predictable chip formation and evacuation. These characteristics translate directly into fewer interruptions and higher overall productivity on the shop floor. Secure clamping and geometry compatibility for reliable assembly A secure mechanical interface is essential for repeatable performance: the insert features a cylindrical hole with a single-sided countersink (40°–60°), ensuring secure clamping in compatible tool bodies. The specified 15° relief angle and an 85° approach angle support a broad spectrum of milling tasks without compromising the seating or stability of the insert. It is essential that the insert seat, geometry and milling body are technically matched; correct mating prevents micro-movements that can reduce surface quality and tool life. Clear compatibility ensures predictable results across varied workpiece materials. Practical benefits for diverse milling applications This insert is suited to planing, shoulder, slot and contour milling as determined by the chosen tool family. The defined 0.8 mm corner radius provides a good compromise between strength and detail, helping to maintain corner integrity while allowing fine edge finishes where required. The insert thickness and parallelogram form enable flexibility in cutter design, permitting the same grade to be employed across several operations, thereby simplifying tooling inventories and supporting quicker changeovers and consistent part quality. Material suitability and handling recommendations Selected for general milling use, the grade complements the geometry to enhance chip control and cutting-edge robustness. The insert is manufactured from carbide and intended for use in Tungaloy milling systems; combination with matching cutter bodies is required for optimal results. When replacing inserts, ensure correct torque on the clamping screw and verify seating surfaces for cleanliness to preserve the intended performance and service life. Proper mounting and verified compatibility contribute directly to reduced downtime and improved machining repeatability. For reliable, long-lasting milling performance with Tungaloy technology, request the ADMT210408 T3130 through Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical guidance and ordering assistance Technical Data Article number: 6853806 Manufacturer SKU: TUN6853806 Model series: Fräswendeschneidplatten Material: Carbide Facts Corner radius: 0.8 mm Plate size: 21 mm Plate thickness: 4.76 mm Relief angle: 15° Approach angle: 85° Special features Grade: T3130 Shape: Parallelogram Hole: cylindrical hole with single-sided countersink (40°–60°) Chipformer: one-sided Application: Milling (face, shoulder, slot, high-feed, contour) FAQ What milling operations is this insert suitable for? The ADMT210408 T3130 indexable insert by Tungaloy is designed for face, shoulder, slot, high-feed and contour milling depending on the selected cutter family. Does the insert require a specific tool body? The insert must be used in a tool body with matching seat geometry; the ADMT210408 requires compatible Tungaloy milling bodies to ensure correct seating and clamping. Which material is the insert made from and what advantages does it offer? Manufactured from carbide and supplied in the T3130 grade, the ADMT210408 offers a balance of wear resistance and toughness for longer tool life and stable cutting-edge performance. What does the hole style mean for clamping? The cylindrical hole with a single-sided countersink (40°–60°) ensures secure clamping and correct axial positioning when used with the appropriate clamping screw and cutter body. What does the 0.8 mm corner radius affect in machining? A 0.8 mm corner radius improves corner robustness while allowing acceptable surface finish; it is suitable for many general milling tasks without compromising edge strength. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
ADMT080302R-F56 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, precise parallelogram 85° geometry and a controlled F56 chipbreaker for stable, productive milling of steel and cast iron; order directly via Metav Werkzeuge or request expert advice from the consultancy team. ADMT080302R-F56 WKP35G — Indexable milling insert, Tiger·tec Gold (Walter Tools) The ADMT080302R-F56 WKP35G is an indexable milling insert engineered for productive machining of steel and cast iron, offering a tight tolerance class and a geometry optimised for reliable chip control. Tiger·tec Gold coating for extended tool life Suitable for steel and cast iron machining Parallelogram 85° form for versatile engagement WKP35G grade for consistent wear resistance Increased throughput through optimised coating and grade The combination of Tiger·tec Gold coating and the WKP35G grade provides a balance between adhesive and abrasive wear resistance, which directly translates into longer tool life and fewer changes on the machine. The coated cemented carbide substrate is designed to withstand the thermal and mechanical stresses typical when cutting steel, while also managing the abrasive tendencies of cast iron. This results in fewer interruptions, more consistent component quality and a measurable improvement in process economy when compared with uncoated alternatives. Geometry tuned for reliable chip control and surface finish The parallelogram 85° plate form and F56 chipbreaker create a cutting geometry that promotes predictable chip formation and evacuation. The positive engagement angle reduces cutting forces and vibration, improving stability in interrupted cuts and slotting operations. A 0.2 mm corner radius contributes to edge strength without compromising the achievable surface finish, making the insert suitable for both roughing and light finishing passes where stability and repeatability are required. Dimensional consistency and process integration Manufactured to a tolerance class M, the insert maintains repeatable seating and predictable tool life across batches, simplifying toolholder setup and calibration. The standard plate size (08) with a plate thickness of 03 ensures compatibility with common mill toolholders for indexable inserts of this geometry. The 15° relief angle supports a favourable cutting edge orientation that lowers heat generation at the flank, reducing the risk of early edge degradation and supporting longer cutting intervals. Practical benefits for production planning Specifying the ADMT080302R-F56 WKP35G enables planners to standardise inserts across a range of steel and cast iron operations, reducing inventory complexity and streamlining reordering. The design supports higher cutting speeds and promotes consistent chip breaking, which can reduce cycle times and improve machine uptime. Clear, catalogued material suitability and series information supports efficient process selection and easier integration into production recipes and CAM tool libraries. For ordering or to discuss machining strategies with Metav Werkzeuge, please contact the sales team via info@metav-werkzeuge.com or call +49 2822 7131930 — expert guidance and rapid supply options are available Technical data Article number: ADMT080302R-F56-WKP35G-WALTER Name: Fräswendeschneidplatte ADMT080302R-F56 WKP35G Walter Tools Manufacturer: Walter Tools Facts Plate size: 08 Plate thickness: 03 Corner radius: 0.2 mm Relief angle: 15° Plate form: Parallelogram 85° Chipbreaker: F56 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WKP35G Material designation: P / K Applicable materials: Steel, Cast iron Execution: T ISO designation: ADMT080302R-F56 WKP35G FAQ What materials is this insert suitable for? The ADMT080302R-F56 WKP35G insert from Walter Tools is specified for steel (P) and cast iron (K), reflecting the design and coating choices of the Tiger·tec Gold series. How does the F56 chipbreaker affect cutting performance? The F56 chipbreaker on the ADMT080302R-F56 WKP35G promotes controlled chip formation and evacuation, which reduces the risk of chip re-cutting and supports stable cutting conditions in both roughing and lighter finishing operations. Is this insert compatible with common toolholders for parallelogram inserts? Yes; the parallelogram 85° form and standard size (08) make the insert compatible with typical indexable milling toolholders designed for this geometry, enabling straightforward interchangeability. What advantage does the WKP35G grade offer in production use? The WKP35G grade provides a robust, coated carbide solution optimised for mixed demands of adhesive and abrasive wear, offering consistent tool life and predictable performance across batches — particularly valuable for repetitive production environments. How does the 0.2 mm corner radius influence tool life and finish? A 0.2 mm corner radius increases edge strength to resist chipping under load while remaining small enough to achieve acceptable surface finishes in finishing passes, striking a compromise between durability and appearance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The item offered is original, factory-new goods of the manufacturer.
ADMT080302R-F56 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of consistent wear resistance, versatile material compatibility and a geometry engineered for stable chip control to increase productivity in milling operations; order directly via Metav Werkzeuge or consult our experts for application support. ADMT080302R-F56 WKP35S milling indexable insert — Parallelogram 85°, Tiger·tec Silver ADMT080302R-F56 WKP35S is a precision milling indexable insert designed for high-productivity finishing and semi-finishing in Stahl and Gusseisen applications. Tiger·tec Silver coating for reliable wear resistance WKP35S grade optimised for Stahl and Gusseisen Parallelogram 85° form with 15° clearance angle Corner radius 0.2 mm for consistent surface finish High-efficiency cutting performance that stabilises cycle times The insert offers a combination of a robust coated grade and a defined geometry to deliver predictable tool life and repeatable results. The WKP35S grade, part of the Tiger·tec Silver family, is formulated for the thermal and abrasive conditions typical of machining Stahl and Gusseisen; this results in improved process security and reduced unplanned tool changes. The parallelogram 85° shape and 15° clearance angle provide an effective balance between cutting edge strength and chip evacuation, enabling higher feed rates without sacrificing surface integrity. For production environments where throughput and consistency matter, this geometry supports a smoother production flow and more reliable cycle planning. Durable coating and edge control for consistent component quality A multilayer coating strategy in the Tiger·tec Silver technology enhances resistance to abrasive wear and thermal loading, helping to maintain a sharp cutting edge over longer lifetimes. The small corner radius (0.2 mm) is optimised for achieving fine surface finishes in finishing passes while still offering sufficient strength to withstand moderate interruptions. The integrated chipbreaker F56 promotes controlled chip formation and evacuation, which reduces the risk of chip re-cutting and surface defects. Together these features contribute to consistent part tolerance and surface quality, lowering downstream finishing costs and improving first-pass yield. Practical application benefits and operational guidance This insert is configured for flexible deployment in milling applications where Stahl and Gusseisen workpieces are common. The classification P / K reflects its suitability across those ISO material groups, so the same insert can cover a range of components without frequent tool changes. From a maintenance and inventory perspective, the standardised designation supports straightforward identification and replacement in tool carriers. For operators and process engineers, noting the grade and chipbreaker combination allows optimised selection of cutting parameters and coolant strategy to eke out extended life and predictable results. Technical consultation is available for cutting data recommendations tailored to machine power and workpiece geometry. For tailored cutting data and to source genuine Walter Tools inserts, contact Metav Werkzeuge for expert advice and availability. Technical Data Article number: ADMT080302R-F56-WKP35S-WALTER Designation: ADMT080302R-F56 WKP35S Series: Tiger-tec Silver Grade: WKP35S Form: Parallelogram 85° Chipbreaker: F56 Manufacturer: Walter Tools Facts Clearance angle: 15° Corner radius: 0.2 mm Plate size: 08 Plate thickness: 03 Tolerance class: M Special features Coating: Tiger·tec Silver Material suitability: Stahl Material suitability: Gusseisen Sortenbeschreibung: beschichtetes Hartmetall Baureihe: Tiger-tec Silver FAQ What materials is this insert intended for? The ADMT080302R-F56 WKP35S insert is specified for machining Stahl and Gusseisen, reflecting the P / K ISO grouping of the grade. Which grade and coating are used on this insert? This indexable insert uses the WKP35S grade within the Tiger·tec Silver coating family, chosen to balance thermal resistance and abrasive wear performance. How does the parallelogram 85° form affect milling operations? The parallelogram 85° form combined with a 15° clearance angle enhances edge stability and chip flow, improving process security during finishing and semi-finishing passes. Is the chipbreaker suitable for mixed operations? The F56 chipbreaker is designed for controlled chip formation across a range of feeds, supporting consistent surface quality in mixed Stahl and Gusseisen workloads. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original, brand-new goods from the manufacturer (Walter Tools).
ADMT080302R-F56 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WSM35G grade for consistently stable chip formation and extended edge life when machining stainless steels and heat‑resistant superalloys; order directly via Metav Werkzeuge or consult their specialists for application‑specific recommendations. ADMT080302R-F56 WSM35G — Parallelogram 85° milling indexable insert, Tiger‑tec Gold, Walter Tools ADMT080302R-F56 WSM35G is a Tiger‑tec Gold coated milling indexable insert engineered for reliable machining of stainless steels and heat‑resistant superalloys in demanding production environments Tiger‑tec Gold grade WSM35G Optimised for stainless steels (ISO M) Also for superalloys and titanium (ISO S) Parallelogram 85°, 15° relief angle High‑temperature performance for tough materials The WSM35G grade, part of the Tiger‑tec Gold series, combines a coated carbide substrate with a specialised coating to provide improved wear resistance and thermal stability when cutting difficult materials. For components where heat builds up at the cutting edge—typical of stainless steels and superalloys—this material pairing reduces flank wear and preserves cutting geometry, which helps maintain dimensional accuracy and surface finish over longer tool life spans. Geometry that secures chip control and repeatability The parallelogram 85° form and the specified chipbreaker F56 work together to produce predictable chip formation and evacuation in interrupted and continuous cuts. A 15° relief angle and a 0.2 mm corner radius balance edge strength with cutting finesse, allowing the insert to deliver consistent performance across a range of feed rates. These geometric choices translate into fewer unplanned tool changes and steadier cycle times on production lines. Productivity gains through stable edge life By favouring a coating and grade combination designed for adhesion resistance and thermal management, the insert supports higher process reliability and improved economy per cutting length. The coated carbide technology reduces the tendency to form built‑up edge on reactive materials, resulting in better surface integrity and less scrap. In practice, this can reduce downtime and help achieve predictable batch throughput in series production. Practical use and application tips This indexable insert is tailored to ISO groups M (stainless steels) and S (heat‑resistant superalloys and titanium). Selection of appropriate cutting data—moderate cutting speeds for stainless steels and adjusted feeds for titanium alloys—will leverage the WSM35G properties best. If further machining parameters or compatibility checks are required for specific component geometries or machines, Metav Werkzeuge’s technical advisers can provide cutting data and optimisation guidance. For production tasks that demand secure chip control and sustained edge stability, choose Walter Tools’ Tiger‑tec Gold inserts and contact Metav Werkzeuge for tailored machining advice and expedited supply arrangements Technical Data Article number: ADMT080302R-F56-WSM35G-WALTER Designation: ADMT080302R-F56 WSM35G Product type: milling indexable insert Manufacturer: Walter Tools Core specifications Size code: 08 Thickness code: 03 Relief angle: 15° Corner radius: 0.2 mm Shape: Parallelogram 85° Chipbreaker: F56 Tolerance class: M Features & suitability Series: Tiger‑tec Gold Grade: WSM35G (coated carbide) Applicable materials: ISO M (stainless steels); ISO S (superalloys, titanium) Stable chip formation High temperature resistance Execution: T FAQ Which materials is the ADMT080302R-F56 WSM35G suitable for? The ADMT080302R-F56 WSM35G insert from Walter Tools is intended for stainless steels (ISO M) and heat‑resistant superalloys and titanium (ISO S), offering improved chip control and edge stability in these groups. What are the key geometric specifications of the insert? This insert features a parallelogram 85° shape, a 15° relief angle and a 0.2 mm corner radius, with chip control provided by the F56 breaker to ensure consistent evacuation. What is the benefit of the F56 chipbreaker? The F56 chipbreaker is designed to promote short, controllable chips in difficult materials, reducing the risk of entanglement and improving process stability during milling operations. How does the Tiger‑tec Gold coating affect performance? The Tiger‑tec Gold coating increases wear resistance and thermal stability, which helps maintain edge integrity under elevated temperatures and reduces the frequency of insert changes. Is this insert better for roughing or finishing operations? Depending on insert geometry and cutting parameters, the ADMT080302R-F56 WSM35G can be applied for both finishing and semi‑finishing in stainless steels and superalloys; appropriate feeds and speeds should be selected to match the desired surface quality and tool life. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanatory purposes only. There is no connection between our company and the named brands beyond the sale of original, brand‑new manufacturer products.
ADMT080302R-F56 WSM35S T Wendeplatten - Walter Tools
Maximise machining reliability by combining the Tiger·tec Silver coating with the WSM35S grade for stable cutting edges and improved chip control; order directly via Metav Werkzeuge or consult the technical advisers for application-specific recommendations. ADMT080302R-F56 WSM35S indexable milling insert for rostfreier Stahl & superalloys — Walter Tools ADMT080302R-F56 WSM35S is a parallelogram 85° indexable insert designed for heavy-duty and high-temperature materials, optimised for machining rostfreier Stahl and heat-resistant superalloys. Tiger·tec Silver coating technology Optimised for rostfreier Stahl machining Parallelogram 85° form for reliable engagement 15° relief and 0.2 mm corner radius High-performance grade and coating for consistent cutting The ADMT080302R-F56 WSM35S pairs the WSM35S coating grade with Tiger·tec Silver technology to reduce flank wear and support stable cutting edge behaviour under thermal stress. This engineered combination improves tool life when confronting tough, adhesive materials: the result is more predictable tool-change intervals and fewer interruptions in production. The coating and grade jointly promote controlled chip control, which lowers the risk of built-up edge and supports consistent part quality during medium to heavy cut applications. Geometry and chip control that stabilise the machining process The insert’s Parallelogram 85° geometry and F56 chipbreaker are specified to deliver repeatable engagement and reliable chip formation. A 15° relief reduces rubbing and heat generation at the cutting face, while the 0.2 mm corner radius balances edge strength with acceptable surface finish. These geometric choices translate directly into reduced downtime, fewer edge failures and improved first-pass yield in serial production—advantages that feed into a measurable improvement in process throughput. Application focus and integration into workshop routines Designed for the material groups S / M, this insert is especially effective on rostfreier Stahl and heat-resistant alloys where thermal resistance and edge stability are critical. As an indexable insert, it integrates with common milling toolholders and supports quick index changes to maintain cycle times. For workshops seeking process reliability when working with demanding materials, the combination of grade, coating and geometry offers a pragmatic solution that lowers scrap risk and enhances surface consistency without adding machining complexity. Contact Metav Werkzeuge for tailored application advice on the ADMT080302R-F56 WSM35S insert and to discuss optimal cutting parameters and tooling assemblies Technical data Article number: ADMT080302R-F56-WSM35S-WALTER Designation: ADMT080302R-F56 Product type: Indexable milling insert Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 0.2 mm Size: 08 Thickness: 03 Form: Parallelogram 85° Special features Series: Tiger·tec Silver Grade: WSM35S Chipbreaker: F56 Tolerance class: M Material groups: S / M Suitable for: rostfreier Stahl and heat-resistant superalloys Execution: T FAQ Is this insert suitable for rostfreier Stahl? Yes. The ADMT080302R-F56 WSM35S insert and its Tiger·tec Silver grade are specified for rostfreier Stahl and support stable chip formation when machining these materials. Which chipbreaker is fitted and what is its benefit? The insert uses the F56 chipbreaker, which is designed to promote controlled chip formation and reduce the risk of built-up edge in demanding cuts. What are the key geometry parameters to note? The insert features a parallelogram 85° form, a 15° relief angle and a 0.2 mm corner radius, optimised for balance between edge strength and surface finish. Can the insert be used for titanium or superalloys? Yes. The WSM35S grade and Tiger·tec Silver series are suitable for heat-resistant superalloys and titanium (material group S), offering thermal stability and edge robustness. How does the geometry influence tool life? The 15° relief and 0.2 mm corner radius reduce rubbing and distribute cutting forces, which helps maintain the integrity of the cutting edge and extends tool life under cyclic thermal loads. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany; info@walter-tools.com Protected trademarks and product names are the property of their respective owners and are mentioned solely for explanation. There is no affiliation between Metav Werkzeuge and the trademark owners. The offered article is an original, factory-new product of the manufacturer.
ADMT080302R-F56 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, broad material applicability (P / M / S) and a stable parallelogram geometry for reliable, productive milling; order the ADMT080302R-F56 WSP45G directly via Metav Werkzeuge or consult our specialists for cutting data. ADMT080302R-F56 WSP45G – Milling insert, Tiger·tec Gold, Walter Tools The ADMT080302R-F56 WSP45G is a parallelogram 85° milling insert engineered for versatile face and shoulder milling of Stahl, rostfreier Stahl and high‑temperature alloys in industrial machining. Tiger·tec Gold PVD‑coated carbide Suitable for Stahl, rostfreier Stahl and high‑alloy S Parallelogram 85° geometry for stable milling 15° clearance and 0.2 mm corner radius Higher productivity through advanced coating and grade The combination of the Tiger·tec Gold coating and the WSP45G grade delivers improved thermal resistance and edge stability under typical milling loads. This PVD‑coated carbide is optimised for demanding cutting conditions, reducing flank wear and extending tool life which leads to longer uninterrupted production runs and fewer tool changes. The coating technology supports consistent chip formation and helps maintain surface quality when working with tougher materials. Broad material range for fewer tool changes Designed for the ISO groups P / M / S, this insert offers practical flexibility: P indicates suitability for unalloyed and alloyed Stahl, M denotes compatibility with rostfreier Stahl, and S covers heat‑resistant superalloys and Titan. Such versatility reduces the need for multiple tool families on the shop floor, simplifying inventory while ensuring process stability across a range of components. The grade’s toughness supports secure chip control and helps to prevent build‑up edge when machining sticky or heat‑sensitive workpieces. Geometry and edge design for consistent surface quality The parallelogram 85° shape, combined with a 15° clearance and a 0.2 mm corner radius, provides a robust cutting edge that resists chipping during interrupted cuts. The F56 chipbreaker encourages predictable chip flow for improved evacuation, which in turn reduces rework and downtime. With tolerance class M and execution T, the insert sits securely in the toolholder, delivering repeatable results and reliable run‑out behaviour—key for maintaining tight tolerances in serial production. Practical application guidance for process security For high‑productivity milling, the insert’s balance of edge stability and toughness permits increased feed rates while maintaining acceptable surface finish and tool life. In applications where thermal load and adhesion are critical—such as when machining rostfreier Stahl or superalloys—the coated grade supports stable cutting edges and consistent performance. For specific cutting speeds and feed recommendations, Metav Werkzeuge’s technical advisors can supply matching parameters to integrate the insert into existing machining cycles and tool assemblies. Contact Metav Werkzeuge for tailored cutting data and procurement: info@metav-werkzeuge.com | +49 2822 7131930 — discuss the ADMT080302R-F56 WSP45G to determine optimal feeds, speeds and toolholder configuration Technical data SKU: ADMT080302R-F56-WSP45G-WALTER Item designation: ADMT080302R-F56 WSP45G Label: Fräswendeschneidplatte ADMT080302R-F56 WSP45G Walter Tools Series: Tiger-tec Gold Manufacturer: Walter Tools Core specifications Relief angle: 15° Corner radius: 0.2 mm Insert size: 08 Thickness: 03 Shape: Parallelogram 85° Tolerance class: M Features Coating / grade: Tiger·tec Gold / WSP45G Chipbreaker: F56 Material groups: P / M / S Execution: T Type: Fräswendeschneidplatte FAQ What materials is the ADMT080302R-F56 WSP45G suitable for? The ADMT080302R-F56 WSP45G insert is specified for ISO groups P / M / S, meaning it is suitable for machining Stahl, rostfreier Stahl and heat‑resistant superalloys including Titan. What advantage does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WSP45G grade enhances thermal resistance and edge life, allowing the ADMT080302R-F56 WSP45G to maintain cutting performance and surface quality under elevated cutting temperatures. How does the parallelogram 85° geometry affect milling? The parallelogram 85° form offers stable radial engagement and improved edge support, which helps to reduce vibration and deliver consistent surface finishes when milling shoulders and faces with the ADMT080302R-F56 WSP45G insert. Is the insert suitable for interrupted cuts and heavy engagement? Yes, the combination of the WSP45G grade, a 0.2 mm corner radius and the robust geometry provides resistance to chipping, making the ADMT080302R-F56 WSP45G well suited for interrupted cuts and demanding milling operations. Which chipbreaker should be selected for general milling with this insert? The ADMT080302R-F56 WSP45G is supplied with the F56 chipbreaker, which is optimised for controlled chip formation and reliable evacuation in a range of milling applications. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT080304L-F56 WKP35G Wendeplatten - Walter Tools
Take advantage of the proven combination of the Tiger·tec Gold coating and the WKP35G grade for efficient machining of steel and cast iron; the geometrical design with 15° clearance and a 0.4 mm corner radius supports stable chip formation and consistent surface quality. Order directly via Metav Werkzeuge or consult their advisors for tailored application advice. ADMT080304L-F56 WKP35G milling insert – Tiger·tec Gold, for steel and cast iron by Walter Tools The ADMT080304L-F56 WKP35G is a parallelogram 85° milling insert designed for productive finishing and roughing in steel and cast iron applications. Tiger·tec Gold coating for enhanced wear resistance WKP35G grade for steel and cast iron machining Parallelogram 85° form with 15° clearance 0.4 mm corner radius; chipbreaker F56 for stable chips Broad material coverage and durable coating for long tool life The insert’s Tiger·tec Gold technology and WKP35G grade combine to deliver a coated carbide construction optimised for the thermal and abrasive conditions encountered when machining steel and cast iron. Coated carbide means a hard substrate with engineered surface layers that reduce wear and improve edge stability; this results in longer tool life and lower tool-change frequency. For production environments where predictable tool life is essential, the coating and grade are selected to provide stable chip formation and resistance to flank wear, supporting higher machine utilisation and reduced process interruptions. Geometry and edge design that control chips and surface finish The insert’s parallelogram 85° form together with 15° clearance and a 0.4 mm corner radius is intended to balance cutting strength and surface integrity. The geometry channels chips effectively and reduces cutting forces during engagement, while the chipbreaker F56 promotes breakage into controllable segments, which eases evacuation and lessens re-cutting. These characteristics translate into improved component finish and reduced vibration in many milling operations. The design is particularly suitable where a compromise is needed between finishing quality and robust cutting performance. Productivity advantages and process reliability in daily use As an indexable insert, this design allows quick, repeatable insert changes and supports stable productivity across series production runs. The combination of grade and geometry is aimed at achieving productive machining with predictable tool behaviour, facilitating consistent cycle times and surface results. Walter Tools’ specifications for this family focus on reproducible performance across a broad range of cutting conditions, making the insert a practical choice where both reliability and flexibility are required. For further process optimisation or application-specific recommendations, Metav Werkzeuge can provide technical guidance and supply options. For process-stable machining with Walter Tools' Tiger·tec Gold inserts, contact Metav Werkzeuge for expert application advice and reliable supply. Technical data SKU: ADMT080304L-F56-WKP35G-WALTER Designation: ADMT080304L-F56 WKP35G Type: Milling indexable insert Manufacturer: Walter Tools Core data Clearance angle: 15° Corner radius: 0.4 mm Form: Parallelogram 85° Plate size: 08 Plate thickness: 03 Tolerance class: M Chipbreaker: F56 Special features Series: Tiger·tec Gold Grade: WKP35G (coated carbide) Applicable materials: Steel (P), Cast iron (K) Execution: T FAQ Which materials are best suited for this insert? The ADMT080304L-F56 WKP35G is specified for steel (P) and cast iron (K); the WKP35G grade and Tiger·tec Gold coating are selected to handle the thermal and abrasive demands of these materials. What is the purpose of the 0.4 mm corner radius? A 0.4 mm corner radius increases edge strength compared with sharper radii, improving tool life and offering a balance between surface finish and robustness in interrupted or heavy cuts. How does the chipbreaker affect machining performance? The chipbreaker F56 is designed to produce short, controllable chips during milling, which enhances evacuation, reduces recutting, and contributes to a more stable cutting process with improved surface results. Is this insert suitable for finishing and roughing operations? Yes, the combination of WKP35G and the insert geometry makes it adaptable for both finishing and moderate roughing, with adjustments to cutting parameters to match the required material removal and surface quality. Can the insert be used in standard tool holders for parallelogram inserts? The form is a parallelogram 85° design; compatibility depends on the tool holder system, so the specific holder geometry should be confirmed against the ADMT080304L-F56 WKP35G dimensions. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, factory-new goods of the manufacturer.
ADMT080304L-F56 WKP35S Wendeplatten - Walter Tools
The combination of Tiger·tec Silver coating, WKP35S grade and precise parallelogram 85° geometry delivers stable chip control and prolonged tool life, supporting continuous, productive milling of steel and cast iron; order the ADMT080304L-F56 WKP35S directly via Metav Werkzeuge or consult the technical advisors for application-specific guidance. ADMT080304L-F56 WKP35S milling insert — Tiger·tec Silver grade for steel and cast iron (Walter Tools) The ADMT080304L-F56 WKP35S is a parallelogram 85° milling insert with a 15° clearance angle, optimised for reliable machining of steel (P) and cast iron (K) Tiger·tec Silver coating for long tool life WKP35S grade for steel and cast iron Parallelogram 85° insert geometry 15° clearance angle with 0.4 mm nose radius Higher throughput through coating and grade synergy The combination of the Tiger·tec Silver coating and the WKP35S carbide grade is engineered to improve life under industrial conditions. The coating reduces abrasive wear while the grade manages heat and maintains edge stability during extended cycles, which translates into fewer tool changes and increased uptime. For production environments where repeatability and consistent component quality are crucial, this pairing supports higher material removal rates without sacrificing surface integrity. The chipformer F56 contributes to controlled chip shape, reducing recutting and stabilising machining forces for smoother cycle times. Consistent results from stable geometry and tolerances The parallelogram 85° shape with a 15° clearance angle and a 0.4 mm nose radius provides robust contact geometry for shoulder and face milling operations. The geometry distributes cutting forces predictably, helping to avoid vibration and minimise edge chipping in interrupted cuts. Tolerance class M ensures interchangeability and reliable seat fitting in indexable toolholders, which helps maintain repeatable positioning and surface finish across multiple inserts. These geometric features make the insert suited to setups where accuracy and repeatable tool performance are operational priorities. Broad material range with focused chip control Designed for ISO groups P (steel) and K (cast iron), this insert offers versatile application potential across common workshop and production materials. The built-in F56 chipbreaker is tuned to the chip behaviour typical of these groups, favouring short, manageable chips in cast iron and reliable chip formation in steels. This tailored chip control reduces cycle interruptions and improves process security, particularly in automated or lights-out machining scenarios. Integration into existing ADMT-style tool systems is straightforward, enabling quick changeover and predictable process behaviour. Production advantages and brand reliability The insert offers a practical balance between wear resistance and toughness, supporting productive milling with fewer tool interventions. Walter Tools' design focus on stable cutting edges and predictable wear patterns contributes to consistent surface quality and lower scrap rates. For operations seeking measurable efficiency gains, the ADMT080304L-F56 WKP35S offers durable performance and process stability, making it an economical choice for medium- to high-volume milling tasks under industrial conditions. Contact Metav Werkzeuge for tailored holder recommendations and delivery options for Walter Tools ADMT080304L-F56 WKP35S milling inserts, including advice on speeds, feeds and compatible tool systems. Technical Data Article number: ADMT080304L-F56-WKP35S-WALTER Designation: ADMT080304L-F56 WKP35S Type: Milling insert (indexable) Series: Tiger·tec Silver Grade: WKP35S Manufacturer: Walter Tools Core data Clearance angle: 15° Nose radius: 0.4 mm Thickness: 3 mm Size code: 08 Tolerance class: M Special features Geometry: Parallelogram 85° Chipbreaker: F56 Material groups: P (steel), K (cast iron) Substrate/coating: Coated cemented carbide (Tiger·tec Silver) Execution: T FAQ What materials is this insert suitable for? The ADMT080304L-F56 WKP35S insert is specified for ISO material groups P and K, meaning it is suitable for machining steel and cast iron. How does the Tiger·tec Silver coating help in production? The Tiger·tec Silver coating on the WKP35S grade reduces abrasive wear and improves heat resistance, extending tool life and supporting consistent productivity in milling operations. What applications benefit most from the parallelogram 85° geometry? The parallelogram 85° geometry is advantageous for shoulder and face milling where stable cutting engagement and predictable force direction are required. Is the chipbreaker suitable for automated machining? Yes, the F56 chipbreaker promotes controllable chip formation for steel and cast iron, which helps reduce cycle interruptions in automated and lights-out machining. Can this insert be used in standard ADMT toolholders? The insert follows the ADMT designation and tolerance class M, allowing compatibility with toolholders designed for ADMT-style indexable inserts when the correct seat geometry is used. Walter Tools (brand appearance: Walter Tools) is part of the Walter AG product family and is recognised for precision machining solutions; the company is associated with high-quality cutting tool technology and global service networks. Protected trademarks and brand names remain the property of their respective owners. The item offered is an original, brand-new product from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
ADMT080304L-F56 WSP45G WSP45G Wendeplatten - Walter Tools
High-performance PVD-coated carbide and a geometry tuned for secure cutting deliver consistent chip control and extended tool life; combine these strengths for efficient milling across steel, stainless steel and high-temperature alloys — order directly via Metav Werkzeuge or request application advice from our consultants. ADMT080304L-F56 WSP45G — Milling indexable insert, Tiger·tec Gold PVD, Walter Tools The ADMT080304L-F56 WSP45G is a parallelogram milling indexable insert with a 15° relief angle, developed for versatile milling of steel, stainless steel and heat-resistant alloys. Tiger·tec Gold PVD coating Suitable for steel, stainless steel, superalloys 15° relief angle for secure engagement Parallelogram 85° form, 0.4 mm nose radius Delivering stable cutting across diverse materials The Tiger·tec Gold chemistry combined with a PVD-coated substrate provides a balanced mix of wear resistance and toughness suited to the P/M/S material groups. This WSP45G grade is formulated to cope with the high temperatures and adhesive tendencies of stainless steels while maintaining edge security when machining alloyed steels and heat-resistant superalloys. The result is stable chip formation and predictable tool behaviour, which supports higher process reliability in both mixed-batch production and serial milling tasks. Geometry designed for predictability and edge security A 15° relief angle and a 0.4 mm nose radius create a cutting geometry that reduces edge loading while preserving profile accuracy. The parallelogram 85° form gives an advantageous entering angle for face and shoulder milling, promoting efficient chip split and lower cutting forces. Combined with the F56 chipbreaker, the insert moderates chip size for safe evacuation and consistent surface finish, supporting repeatable results and fewer interruptions for rework. Productivity gains with lower total machining cost By pairing coated carbide metallurgy with optimised geometry, the insert extends effective tool life and reduces the frequency of index changes. Less tool handling and fewer tool changes translate into reduced machine downtime and improved throughput. For operations where consistent surface quality and dimensional control matter, this component contributes to a lower cost per part through longer edge life and better process stability — a rational investment in productivity rather than a speculative upgrade. Application recommendations and machining approach The ADMT080304L-F56 WSP45G is suitable for a wide range of milling operations, from semi-finish passes to continuous profiling, when working with steels, stainless steels and heat-resistant alloys. For best results, combine the insert’s Tiger·tec Gold coating with cutting parameters that control heat at the cutting zone and ensure appropriate coolant or high-pressure air management as required by the workpiece material. For tailored cutting data and feed/speed suggestions specific to machining centres or bar-feed setups, consult Metav Werkzeuge’s technical advisors to match cutting conditions to production goals. Contact Metav Werkzeuge today to discuss application-specific cutting data or to request the ADMT080304L-F56 WSP45G from Walter Tools for improved milling performance and process reliability. Technical Data Article number: ADMT080304L-F56-WSP45G-WALTER Designation: Fräswendeschneidplatte ADMT080304L-F56 WSP45G Walter Tools Product type: milling indexable insert Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Insert size: 08 Thickness: 03 (code) Corner radius: 0.4 mm Relief angle: 15° Tolerance class: M Special features Grade: WSP45G (PVD-coated carbide) Chipbreaker: F56 Shape: parallelogram 85° Applicable materials: P / M / S Execution: T FAQ Which materials are suitable for this milling insert? The ADMT080304L-F56 WSP45G is specified for the P/M/S groups, meaning it machines unalloyed and alloyed steel, stainless steel and heat-resistant superalloys effectively. What advantage does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the insert enhances wear resistance and edge life while retaining sufficient toughness to resist chipping, offering balanced performance across varied milling tasks. How does the insert geometry affect surface finish and tool life? The combination of 15° relief angle, 0.4 mm nose radius and the F56 chipbreaker reduces cutting forces and improves chip control, which helps maintain surface quality and extends effective tool life. Is this insert suitable for finishing operations? Yes — with appropriate feeds and speeds, the insert’s geometry and coating support both semi-finish and finishing passes while delivering consistent dimensional accuracy. How to choose cutting parameters for the insert? Select parameters that control heat generation for the workpiece material: moderate depths of cut and feeds for stainless steels and superalloys, while higher material removal rates can be used for unalloyed steels; consult Metav Werkzeuge for application-specific data. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
ADMT080304R-D56 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of sharp aluminium‑grade cutting geometry, stable chip control and predictable edge life to increase throughput in non‑ferrous milling operations. Order the inserts directly via Metav Werkzeuge or request application guidance from the technical consultants. ADMT080304R-D56 WAK15 — Fräswendeschneidplatte (indexable milling insert) by Walter Tools, for aluminium and non‑ferrous metals ADMT080304R-D56 WAK15 is an indexable milling insert designed for productive machining of aluminium and other non‑ferrous materials, combining a dedicated insert grade with a chipbreaker geometry for consistent performance Uncoated carbide for aluminium machining 15° relief angle for sharp cutting Parallelogram 85° geometry for versatile milling 0.4 mm corner radius for fine edge definition Faster, cleaner aluminium machining with a purpose‑built grade The WAK15 grade is an uncoated carbide specifically developed for machining aluminium and other non‑ferrous metals (ISO group N). In practice, this means the cutting edge is optimised for low adhesion and minimal built‑up edge, while the chipbreaker D56 promotes controlled chip formation and evacuation. For operations that prioritise cycle time and surface quality in soft, sticky materials, the ADMT080304R‑D56 WAK15 delivers a predictable cutting behaviour that reduces rework and improves first‑pass yield. Geometry that balances sharpness and edge security The insert’s Parallelogram 85° shape and 15° relief angle combine to create a sharp, accessible cutting edge with reduced interference on radial engagements. The modest 0.4 mm corner radius supports a fine edge geometry that enhances surface finish without compromising strength for light to moderate depths of cut. These geometry choices give reliable edge contact and stable milling characteristics, particularly in interrupted cuts or trochoidal strategies where consistent edge performance is essential. Process reliability through material and series design As part of the Walter N‑Sortensystem, this insert benefits from a production philosophy focused on stable chip formation and broad applicability across non‑ferrous alloys. The uncoated hardness and edge form provide repeatable life and predictable dressing intervals, which supports planning for tool changeovers and inventory rotation. Using this insert helps to reduce unexpected downtime and contributes to a steady production rhythm in aluminium component machining. Practical fitment and shop‑floor benefits Available in size 08 with thickness 03, the insert fits standard toolholders designed for parallelogram‑style inserts and suits many common milling set‑ups used for non‑ferrous work. The combination of chipbreaker D56 and the WAK15 grade reduces the tendency for built‑up material on the edge, improving surface integrity and decreasing manual cleaning. For production planners and operators aiming for consistent part finish and efficient toolhandling, these characteristics simplify process control and quality assurance. Contact Metav Werkzeuge for tailored application advice and reliable supply of Walter Tools ADMT080304R-D56 WAK15 inserts; technical consultants are available to discuss integration into existing milling processes Technical data SKU: ADMT080304R-D56-WAK15-WALTER Article designation: ADMT080304R-D56 WAK15 Manufacturer: Walter Tools Product type: Indexable milling insert (milling insert) Facts Relief angle: 15° Corner radius: 0.4 mm Plate form: Parallelogram 85° Plate size: 08 Plate thickness: 03 Chipbreaker: D56 Tolerance class: M Special features Walter N‑Sortensystem Grade WAK15 — uncoated carbide for non‑ferrous metals Optimised chip formation for aluminium and NE‑metals Suitable for aluminium machining FAQ What materials is this insert suited for? The ADMT080304R‑D56 WAK15 insert is intended for aluminium and other non‑ferrous metals, following the ISO group N designation for minimal adhesion and optimised chip control. How does the chipbreaker D56 affect performance? The chipbreaker D56 on the ADMT080304R‑D56 WAK15 promotes consistent, segmented chips and improves evacuation, which lowers the risk of edge build‑up during aluminium milling. What benefits does the Parallelogram 85° shape provide? The parallelogram 85° geometry delivers flexible cutting edge orientation and reliable engagement in a range of milling strategies, aiding stability and surface quality when using the WAK15 grade. Is the insert coated or uncoated? This item is uncoated carbide (WAK15), a deliberate choice that reduces material adhesion and yields better performance in soft, sticky non‑ferrous alloys. What are the key dimensions to check for toolholder compatibility? Check plate size 08 and thickness 03, plus the parallelogram form and seat, to ensure proper fitment with the corresponding milling toolholder system. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Mention of brand names and trade marks is for explanation only and does not imply any connection between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer.
ADMT080304R-D56 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WKP25S grade for reliable chip control and prolonged tool life; the D56 chipbreaker and parallelogram 85° form ensure stable clamping and consistent machining of steel and cast iron. Order directly via Metav Werkzeuge or request application advice from our consultants. ADMT080304R-D56 WKP25S Fräswendeschneidplatte – Tiger‑tec Silver coated insert for steel and cast iron (Walter Tools) The ADMT080304R-D56 WKP25S is a parallelogram milling insert designed for secure clamping and high-performance finishing operations on steel and cast iron components. Tiger‑tec Silver coated for extended tool life Optimised D56 chipbreaker for consistent chips Parallelogram 85° form for secure clamping Suitable for steel and cast iron machining Durable coating and grade for predictable productivity The combination of the Tiger‑tec Silver series and the WKP25S grade provides a balanced solution for machining where both wear resistance and edge stability are required. The coated carbide substrate resists thermal and abrasive wear, which translates into longer tool life and fewer indexings during production. For shops running mixed batches of alloyed and unalloyed steels alongside cast components, this configuration supports sustained cycle times and predictable tool-change intervals, contributing to overall process efficiency. Controlled chip formation and machining quality The insert’s D56 chipbreaker is engineered to produce compact, controllable chips when cutting both steels and cast irons, reducing the risk of built-up edge and improving surface finish. Paired with a 15° relief angle and a 0.4 mm corner radius, the geometry minimises cutting forces and supports consistent dimensional results. These aspects help to lower scrap rates and reduce rework, while also enabling stable finishing passes where surface integrity is decisive. Secure clamping and dimensional consistency The parallelogram 85° plate form delivers secure seating in compatible toolholders, improving repeatability and reducing micro‑movement under load. The insert’s size 08 and thickness code 03 match common holder standards, easing integration into existing tooling systems. The coated carbide construction ensures the cutting edge retains geometry across longer series runs, which is especially relevant for repetitive production where tool-change downtime must be minimised. Application guidance and quality assurance Manufactured to tolerance class M, this insert supports consistent interchangeability and predictable performance in standard milling setups. Its designation reflects suitability for ISO groups P and K, meaning the insert is intended for machining steel and cast iron in a range of operations from roughing to finishing, depending on toolpath and cutting data. For customers seeking to align cutting parameters with material batches, technical data sheets and recommended speeds/feed ranges are available to support process validation. Contact Metav Werkzeuge for tailored machining advice on Walter Tools Tiger‑tec Silver inserts and to arrange supply or technical information via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: ADMT080304R-D56-WKP25S-WALTER SKU: ADMT080304R-D56-WKP25S-WALTER Label: Fräswendeschneidplatte ADMT080304R-D56 WKP25S Walter Tools Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Grade/series: WKP25S / Tiger‑tec Silver Material designation: P / K Core technical figures Relief angle: 15° Corner radius: 0.4 mm Plate size: 08 Plate thickness code: 03 Chipbreaker: D56 Tolerance class: M Special features and suitability Coated carbide (Tiger‑tec Silver) Optimised chip control for steel and cast iron Parallelogram 85° plate form Intended for machining ISO groups P (steel) and K (cast iron) FAQ What materials is this insert suitable for? The ADMT080304R-D56 WKP25S is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron with optimised performance using the Tiger‑tec Silver grade. How does the D56 chipbreaker affect machining? The D56 chipbreaker promotes compact, consistent chips, improving surface quality and reducing chip‑related interruptions when milling steels and cast irons with this Walter Tools insert. What does the 0.4 mm corner radius mean for my parts? A 0.4 mm corner radius balances edge strength and surface finish; it reduces the risk of chipping on interrupted cuts while supporting fine finishing where a small radius is required. Is the insert compatible with standard holders? The parallelogram 85° plate form and size 08 designation match common toolholder standards; check holder compatibility and clamping specifications for secure fitting. What advantages does the Tiger‑tec Silver series provide? Tiger‑tec Silver coating enhances wear resistance and thermal stability, extending useful tool life and supporting stable cutting performance across mixed steel and cast iron applications. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools), with headquarters in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names are used for explanation only; there is no affiliation between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer.
ADMT080304R-D56 WKP35G Wendeplatten - Walter Tools
Combine long tool life, stable chip control and precise geometry for reliable, repeatable milling results; suitable for steel and cast iron applications. Order the ADMT080304R-D56 WKP35G directly via Metav Werkzeuge or consult the technical team for application advice. ADMT080304R-D56 WKP35G indexable milling insert — Tiger·tec Gold, D56 chipbreaker (Walter Tools) The ADMT080304R-D56 WKP35G is an indexable milling insert designed for precision milling of steel and cast iron, offering a balanced combination of wear resistance and consistent chip formation for industrial milling operations Tiger·tec Gold coating for longer tool life WKP35G: coated carbide grade Parallelogram 85° with 15° clearance 0.4 mm corner radius for stable cuts Improved productivity through advanced coating and grade The combination of the Tiger·tec Gold coating and the WKP35G carbide grade delivers a measurable increase in process stability and tool life. The engineered coating reduces abrasive wear on the cutting edge, which results in fewer tool changes and less machine downtime. For production environments where cycle time and repeatability matter, this insert provides consistent performance under the thermal and mechanical stresses typical of milling steel and cast iron. The result is a higher material removal rate and predictable insert life, supporting leaner machining processes and lower cost per part. Broad material compatibility and reliable chip control Rated for the ISO material groups P and K, the insert is optimised for unalloyed and alloyed steel as well as cast iron, addressing the common requirements in general machining and component production. The designed chipbreaker geometry D56 promotes controlled chip segmentation and evacuation when machining these materials, reducing the risk of re-cutting and improving surface integrity. The grade and geometry combination helps to manage heat generation and brittle chip formation in cast iron, while maintaining edge stability during continuous cuts in steel. Geometry and handling that support precision milling The insert’s parallelogram 85° form and 15° clearance angle provide a reliable cutting orientation for versatile milling strategies, including face and shoulder operations. The 0.4 mm corner radius increases edge robustness, helping to avoid premature chipping in interrupted cuts. Dimension codes such as size 08 and thickness code 03 reflect industry-standard insert sizing for straightforward toolholder compatibility. Tolerance class M ensures consistent dimensional accuracy across batches, which simplifies tool setup and repeatable fixture planning in series production. Contact Metav Werkzeuge today for detailed application guidance, availability and recommendations for Walter Tools Tiger·tec Gold inserts such as the ADMT080304R-D56 WKP35G — Metav Werkzeuge is available by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: ADMT080304R-D56-WKP35G-WALTER Designation: ADMT080304R-D56 WKP35G Manufacturer: Walter Tools Product type: Indexable milling insert Facts Tolerance class: M Clearance angle: 15° Corner radius: 0.4 mm Plate form: Parallelogram 85° Size designation: 08 Chipbreaker: D56 Plate thickness code: 03 Special features Coating: Tiger·tec Gold Grade: WKP35G (coated carbide) Application: Steel (P) and cast iron (K) Series note: WKP35G is part of the Tiger·tec Gold family, optimised for stable chip formation and wear resistance FAQ What materials can be machined with this insert? The ADMT080304R-D56 WKP35G insert is designed for machining steel (P) and cast iron (K), reflecting the WKP35G grade characteristics for these ISO groups. How does the D56 chipbreaker influence performance? The D56 chipbreaker promotes segmented chip formation and controlled evacuation when milling steel and cast iron, which improves surface finish and reduces tool load spikes with the ADMT080304R-D56 WKP35G. What does the 0.4 mm corner radius mean for machining? A 0.4 mm corner radius increases edge strength and resistance to chipping, particularly beneficial for interrupted cuts and when stability is required across repeated passes. Is this insert compatible with standard toolholders for size 08? The insert uses the industry size designation 08 and the parallelogram 85° form, making it suitable for compatible Walter Tools holders and common carrier designs specified for this insert geometry. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names belong to their respective owners. Brand names and trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory-new goods from the manufacturer.
ADMT080304R-D56 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance and a proven WKP35S grade for stable, productive milling of Stahl and Gusseisen; the D56 chipbreaker and 85° parallelogram form help secure predictable chip control and consistent surface quality. Order directly via Metav Werkzeuge or contact our consultants for cutting data and tool recommendations. ADMT080304R-D56 WKP35S milling indexable insert — Tiger·tec Silver, for Stahl and Gusseisen (Walter Tools) ADMT080304R-D56 WKP35S is a milling indexable insert designed for medium-duty face and shoulder milling in Stahl and Gusseisen, combining Tiger·tec Silver coating technology with a D56 chipbreaker and a 15° relief for process stability Tiger·tec Silver coating for improved wear resistance Optimised for Stahl and Gusseisen machining Parallelogram 85° form for stable cutting 0.4 mm corner radius for enhanced finish Durable wear resistance that keeps production moving The combination of Tiger·tec Silver coating and the WKP35S grade delivers long-lasting edge life under typical milling stresses. Coated cemented carbide reduces flank wear and crater formation, which translates into fewer indexings and more uninterrupted production time. For users working across mixed batches, the insert’s construction supports consistent surface quality, reducing downstream rework and machine downtime. The controlled wear behaviour also simplifies tool-change planning and cost forecasting, making the insert an efficient choice for repeatable operations. Reliable chip control for safer, predictable machining The integrated D56 chipbreaker and the parallelogram geometry produce short, controllable chips when machining Stahl and Gusseisen, lowering the risk of built-up edge and workpiece damage. Efficient chip formation maintains heat dissipation at the cutting zone and supports stable cutting forces, which is particularly valuable on long tool paths or interrupted cuts. The insert’s 0.4 mm corner radius helps to balance edge strength with surface finish, enabling tight tolerances without sacrificing productivity. Geometry and grade tailored for practical application A defined relief angle of 15° and the 85° parallelogram form prioritise rigidity and repeatability in common milling setups. The manufactured tolerances (class M) and the plate dimensions correspond to established clamping systems, allowing straightforward integration into existing toolholders. Material marking P / K indicates suitability for the ISO workpiece groups for Stahl (P) and Gusseisen (K); this labelling helps to select the insert that matches component material and expected thermal and abrasive conditions. The net result is a versatile, practical insert that supports stable cycle times and reproducible part quality. Contact Metav Werkzeuge to discuss Tiger·tec Silver performance for the ADMT080304R-D56 WKP35S insert and request tailored cutting data or a technical quote — eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data Article number: ADMT080304R-D56-WKP35S-WALTER SKU: ADMT080304R-D56-WKP35S-WALTER Product type: Milling indexable insert Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKP35S Facts Insert size: 08 Thickness: 03 Relief angle: 15° Corner radius: 0.4 mm Shape: Parallelogram 85° Chipbreaker: D56 Tolerance class: M Special features Substrate/coating: coated cemented carbide (Tiger·tec Silver) Workpiece suitability: Stahl, Gusseisen Execution: T Plate designation: ADMT080304R-D56 ISO designation: ADMT080304R-D56 WKP35S FAQ What materials is this insert suitable for? The ADMT080304R-D56 WKP35S insert is optimised for machining Stahl and Gusseisen, corresponding to the ISO P and K groups identified for the WKP35S grade. What advantage does the Tiger·tec Silver coating provide? Tiger·tec Silver enhances the coated cemented carbide’s wear resistance and thermal stability, which extends flank life and supports more consistent tool performance under milling loads. How does the D56 chipbreaker affect machining? The D56 chipbreaker is designed to produce short, controlled chips in common milling operations, improving chip control and reducing the chance of chip-related interruptions during production. Is the geometry suitable for finishing operations? With a 0.4 mm corner radius and an 85° parallelogram form, the insert balances edge strength and surface quality, making it suitable for operations where repeatable finishes are required. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original, factory-new goods of the manufacturer Walter Tools.
ADMT080304R-D56 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of high process security and versatile material performance for consistent milling results; the PVD-coated Tiger·tec Gold grade and positive parallelogram geometry ensure reliable chip control and extended tool life. Order the insert directly via Metav Werkzeuge or consult their specialists for application advice. ADMT080304R-D56 WSP45G milling indexable insert — Walter Tools (Tiger·tec Gold, PVD-coated, 15° clearance) The ADMT080304R-D56 WSP45G is a parallelogram-shaped milling indexable insert designed for versatile slotting and face-milling applications across steels, stainless steels and heat-resistant alloys Tiger·tec Gold PVD coating for wear resistance Parallelogram 85° geometry for positive entry 15° clearance angle for smooth cutting action Corner radius 0.4 mm for balanced edge strength Prolonged tool life through advanced coating and grade The Tiger·tec Gold series combines a PVD-coated cemented carbide substrate with a modern multilayer design that improves wear resistance and supports stable chip formation. This insert grade, WSP45G, is tailored for applications where both edge stability and versatility are required; the coating reduces adhesion and thermal damage, which in turn extends effective cutting intervals. For production environments seeking predictable downtimes and fewer indexings, the result is a measurable increase in productivity and lower overall tooling costs. Geometry that promotes secure cutting and consistent surfaces The parallelogram 85° shape together with a 15° clearance angle produces a positive cutting action that reduces entry shock and supports smooth surface finishes. The 0.4 mm corner radius balances edge robustness with acceptable surface quality—suitable for medium-depth roughing and finishing passes without aggressive vibration. The D56 chipbreaker geometry promotes controlled chip segmentation, improving evacuation in interrupted cuts and reducing the risk of built-up edge on long continuous cuts. Broad material capability for mixed-production environments Manufactured for multi-material use, the insert is optimised for the ISO groups P, M and S: steels, stainless steels and heat-resistant superalloys/titanium. The combination of the WSP45G grade and coating addresses typical challenges such as heat generation in steels, edge build-up in stainless steels and thermal resistance required for nickel-based alloys. This makes the insert particularly suited to shops that process mixed batches and require one reliable tool grade to cover a wide material mix. Practical benefits for machining processes and process planning Adopting this insert reduces the need for frequent tool changes and simplifies inventory by covering multiple workpiece groups with one grade. The positive geometry aids in reducing cutting forces, which can allow higher feed rates under stable setups; the robust coating supports repeatable component quality. For production engineers, these attributes translate into improved cycle-time predictability and enhanced process security. Contact Metav Werkzeuge for tailored application support on the Tiger·tec Gold ADMT080304R-D56 WSP45G insert to optimise cutting parameters and secure consistent milling performance Technical Data Article number: ADMT080304R-D56-WSP45G-WALTER Product: milling indexable insert Designation: ADMT080304R-D56 WSP45G Brand: Walter Tools Series: Tiger·tec Gold Grade: WSP45G Chipbreaker: D56 Facts Relief/clearance angle: 15° Corner radius: 0.4 mm Plate size: 08 Plate thickness: 03 Insert shape: Parallelogram 85° Tolerance class: M Special features Coating: Tiger·tec Gold (PVD-coated cemented carbide) Material suitability: Steel (P), Stainless steel (M), Superalloys & Titanium (S) Application: milling (face and slot milling) Positive entry geometry for reduced cutting forces FAQ What materials can be machined with this insert? The ADMT080304R-D56 WSP45G insert is suitable for steel (P), stainless steel (M) and heat-resistant superalloys/titanium (S) due to its WSP45G grade and Tiger·tec Gold coating. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold PVD coating improves wear resistance and reduces adhesion, which supports longer edge life and more consistent chip control during milling. What is the benefit of the parallelogram 85° shape? The parallelogram 85° geometry provides a positive cutting entry that lowers impact at tool engagement, aiding surface quality and enabling reliable performance in interrupted cuts. Is the 0.4 mm corner radius suitable for finishing? A 0.4 mm corner radius offers a compromise between edge strength and surface finish; it is suitable for semi-finishing and finishing where a balance of robustness and quality is required. Can this insert be used for mixed-batch production? Yes; the WSP45G grade and Tiger·tec Gold coating are intended for versatile applications, making the insert a practical choice for workshops processing a variety of materials. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT080304R-F56 WAK15 Wendeplatten - Walter Tools
Taking advantage of a sharp 15° relief and the WAK15 uncoated carbide grade results in reliable, burr‑free machining of aluminium and other non‑ferrous metals; order the ADMT080304R‑F56 WAK15 through Metav Werkzeuge or contact our consultants for application advice. ADMT080304R-F56 WAK15 Fräswendeschneidplatte – for aluminium and non‑ferrous metals | Walter Tools The ADMT080304R‑F56 WAK15 is an indexable milling insert designed for high‑performance machining of aluminium and other non‑ferrous materials, offering a sharp geometry and optimised chip control for stable, productive cutting. Uncoated carbide grade WAK15 15° relief angle for sharp cutting Parallelogram 85° form, 0.4 mm corner radius Chipbreaker F56 optimised for aluminium Faster material removal on aluminium and non‑ferrous metals The combination of the WAK15 uncoated carbide and the chipbreaker F56 enables efficient evacuation of soft chips and reduces built‑up edge when machining aluminium, copper or brass. The insert’s geometry is adapted to the specific demands of non‑ferrous ISO group N, which means that cutting forces are lower and feed rates can be increased without compromising surface quality. This results in shorter cycle times and more parts per shift, supporting higher throughput in production environments. Reduced adhesion and cleaner surfaces through sharp geometry A 15° relief angle combined with a fine 0.4 mm corner radius produces a very sharp cutting edge that minimises material adhesion and smear on the cutting edge. For components where surface appearance and dimensional consistency matter, this geometry helps to maintain a clean contact zone and reduces secondary finishing. The insert’s form also helps to limit vibration at the cutting edge, which further supports improved surface finish on profiles and thin‑wall workpieces. Consistent edge life and reproducible results The ADMT080304R‑F56 WAK15 is manufactured to a tolerance class M and the parallelogram 85° form ensures repeatable seating in compatible toolholders. These controlled tolerances lead to predictable tool life and simpler tool‑change planning. For operations that require batch‑to‑batch consistency, the reproducible performance of this insert reduces inspection effort and supports continuous, reliable production. Seamless integration into Walter N‑series tooling systems Designed for the Walter N‑series, the insert fits holders that are optimised for efficient chip formation and secure clamping. The standardised geometry and clear designation help with quick tool selection and straightforward inventory management. Where toolroom flexibility is needed, the insert’s familiar form factor allows rapid exchange between operations without additional set‑up time, supporting lean processes on the shop floor. Practical benefits for workshop and production planners Beyond cutting performance, the insert aids process planning by simplifying grade selection: the WAK15 grade is expressly intended for non‑ferrous work, such as aluminium and similar alloys. Choosing the correct chipbreaker and edge preparation avoids common issues like material build‑up and erratic tool wear, which translates into lower scrap rates and reduced rework. For teams aiming to raise productivity without complex process changes, this insert offers an effective, low‑risk upgrade. For precision milling of aluminium and non‑ferrous metals, choose the Walter Tools ADMT080304R‑F56 WAK15 and contact Metav Werkzeuge for tailored application support and availability. Technical Data SKU: ADMT080304R-F56-WAK15-WALTER Product type: Fräswendeschneidplatte (milling insert) Manufacturer: Walter Tools Series: Walter N-Sortensystem Grade: WAK15 Chipbreaker: F56 Form: Parallelogramm 85° Execution: T Tolerance class: M Facts Relief angle: 15° Corner radius: 0.4 mm Size code: 08 Thickness code: 03 Special features Uncoated cemented carbide (WAK15) Intended for aluminium and non‑ferrous metals (ISO group N) Optimised chip control for soft chips Stable seating in Walter N‑series holders Parallelogram 85° insert geometry FAQ What materials is this insert suited for? The ADMT080304R‑F56 WAK15 is specifically intended for aluminium and other non‑ferrous materials (ISO group N), offering geometry and a chipbreaker tuned to prevent material adhesion. How does the chipbreaker F56 affect cutting? The chipbreaker F56 on this indexable insert promotes controlled chip formation when machining soft alloys, reducing the risk of long, stringy chips and improving surface consistency. Is the insert coated? No, the WAK15 designation denotes an uncoated cemented carbide grade optimised for sharp edges and low friction on non‑ferrous materials. What does the 0.4 mm corner radius mean for component finish? A corner radius of 0.4 mm helps balance edge strength and finish quality; it supports a smoother surface while remaining sharp enough to limit material build‑up. Can this insert be used in standard Walter N‑series holders? Yes, the ADMT080304R‑F56 WAK15 is made for the Walter N‑series system and will seat correctly in compatible holders designed for the parallelogram 85° form. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
ADMT080304R-F56 WKP25S Wendeplatten - Walter Tools
Take advantage of the WKP25S grade and Tiger·tec Silver coating to increase process reliability and tool life; the parallelogram 85° geometry and F56 chipbreaker ensure controlled chips and simple indexing. Order directly via Metav Werkzeuge or ask the Metav consultants for application advice. ADMT080304R-F56 WKP25S – indexable milling insert, parallelogram 85° (Walter Tools) The ADMT080304R-F56 WKP25S is an indexable milling insert designed for high-productivity machining of steel and cast iron, offering robust edge performance and consistent chip control for batch and single-part production Tiger·tec Silver coating for extended tool life WKP25S grade for steel and cast iron machining Parallelogram 85° geometry for flexible indexing 15° clearance with 0.4 mm corner radius Maximise uptime with advanced coating and grade The combination of the Tiger·tec Silver coating and the WKP25S carbide grade provides a reliable balance between wear resistance and toughness. This results in improved tool life and stable cutting under typical steel and cast iron conditions. The coating reduces flank wear and thermal softening during interrupted cuts, which supports consistent cycle times and fewer tool changes — a clear advantage for high-volume milling and mixed-production environments. Predictable chip control for productive machining Equipped with the F56 chipbreaker, the insert delivers controlled chip formation across a broad range of feed rates. For materials in ISO groups P (steel) and K (cast iron) the chip geometry helps avoid long, stringy chips and encourages short, manageable segments. Better chip control reduces downtime for clearing and improves surface finish, contributing directly to process efficiency and safer operation at the machine. Flexible indexing and secure cutting geometry The parallelogram 85° shape offers multiple usable cutting edges and straightforward indexing, reducing tooling costs per edge. The 15° clearance angle and 0.4 mm corner radius combine to provide a secure cutting edge that tolerates moderate interruptions while maintaining a good balance between strength and edge sharpness. These geometric choices support repeatable programme results and make the insert suitable for diverse milling strategies. Clear specifications that aid planning and procurement Tolerance class M and the plate designation reflect consistent manufacturing accuracy, simplifying tool-holder matching and replacement planning. The insert thickness and plate size align with standard holders for the ADMT family, enabling predictable setup times and inventory handling. Using a dedicated grade from a recognised range reduces qualification effort and helps maintain stable production quality. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Silver inserts and to discuss integration into existing toolsets — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: ADMT080304R-F56-WKP25S-WALTER Label: Fräswendeschneidplatte ADMT080304R-F56 WKP25S Walter Tools Product type: Fräswendeschneidplatte Facts Clearance angle: 15° Corner radius: 0.4 mm Plate size: 08 Thickness: 03 Geometry: Parallelogram 85° Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WKP25S Chipbreaker: F56 Material suitability: P / K (Steel, Cast iron) Series: Tiger-tec Silver Execution: T Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The ADMT080304R-F56 WKP25S is specified for ISO groups P and K, meaning it is intended for machining steel and cast iron. What is the benefit of the Tiger·tec Silver coating? The Tiger·tec Silver coating increases wear resistance and thermal stability, which leads to longer cutting life and more consistent performance on the WKP25S grade. How does the F56 chipbreaker affect machining? The F56 chipbreaker promotes short, controlled chips across typical feeds, improving chip evacuation and reducing the risk of entanglement during milling. Why choose the parallelogram 85° shape? The parallelogram 85° geometry offers multiple indexable edges and flexible mounting options, supporting economical edge use and easy re-indexing. What does the 0.4 mm corner radius mean for surface finish? A 0.4 mm corner radius balances edge strength with finish quality: it resists chipping while still enabling a good surface result on general-purpose milling tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
ADMT080304R-F56 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, the WKP35G grade and precise geometry to improve machining stability and extend tool life; order directly via Metav Werkzeuge or ask our consultants for application advice. ADMT080304R-F56 ADMT080304R-F56 WKP35G WKP35G Milling insert, Tiger‑tec Gold, for steel & cast iron — Walter Tools The ADMT080304R-F56 WKP35G is a Tiger‑tec Gold‑coated milling insert developed for productive machining of steel and cast iron, offering reliable chip control and consistent tool life in industrial applications. Tiger·tec Gold coating for extended tool life Optimised F56 chip control for stable chips 15° relief angle for secure cutting engagement Parallelogram 85° shape with 0.4 mm corner radius Higher productivity through coated‑carbide performance The combination of the Tiger‑tec Gold series and the WKP35G grade delivers a wear‑resistant, coated carbide chemistry that is tuned to the thermal and abrasive conditions of machining steel and cast iron. Coated carbide means a hard substrate covered by a protective layer; this reduces flank wear and maintains the cutting edge for longer intervals, which in turn reduces interruptions for tool changes and increases net machining time. The result is measurable process stability and predictable performance in production runs. Geometry engineered for stable cutting and surface quality A 15° relief angle and the parallelogram 85° form combine with a 0.4 mm corner radius to provide a balance between edge strength and accessibility for common milling tasks. The F56 chipbreaker is optimised to break and guide chips reliably in mixed steel and cast‑iron workpieces, preventing long stringing chips and minimising rework. These geometric choices directly improve surface finish and reduce the risk of edge chipping during interrupted cuts, offering tangible benefits for both roughing and semi‑finishing operations. Consistent integration and process reliability Tolerance class M, standard plate dimensions and the proven series specification simplify tool logistics and ensure reproducible seating in compatible toolholders. The ADMT080304R‑F56 series from Walter Tools is designed for repeatable changeovers and predictable wear progression, which supports lean production practices and maintenance planning. Where process stability and reduced scrap rates are priorities, this insert contributes to fewer unplanned stoppages and steadier output quality. Contact Metav Werkzeuge for application‑specific recommendations on the Walter Tools ADMT080304R‑F56 WKP35G milling insert, or to request a tailored proposal: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: ADMT080304R-F56-WKP35G-WALTER Label: Fräswendeschneidplatte ADMT080304R-F56 WKP35G Walter Tools Manufacturer: Walter Tools Product type: Milling insert Facts Relief angle: 15° Corner radius: 0.4 mm Plate size: 08 Plate thickness: 03 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKP35G (coated carbide) Chipbreaker: F56 Shape: Parallelogram 85° Machinable materials: steel (P), cast iron (K) Execution: T FAQ What materials is this insert intended for? The ADMT080304R‑F56 WKP35G insert from Walter Tools is specified for steel (P) and cast iron (K) applications according to its Tiger‑tec Gold technology. How does the F56 chipbreaker affect machining? The F56 chipbreaker on the ADMT080304R‑F56 WKP35G promotes short, controllable chips in both steel and cast iron, reducing chip entanglement and improving component quality. Is the insert compatible with standard toolholders? Yes; the ADMT080304R‑F56 family is produced to standard dimensions and tolerance class M for consistent seating in compatible milling holders. What benefits does the Tiger‑tec Gold series provide? Tiger‑tec Gold coating on the WKP35G grade enhances wear resistance and thermal stability, which extends cutting life and supports uninterrupted machining cycles. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are cited solely for clarification. There is no affiliation between our company and the mentioned brands. The offered article is original, factory‑new goods of the manufacturer.
Why indexable inserts are indispensable in modern machining
Indexable inserts, also known as cutting inserts or indexable cutting inserts, are standardised, replaceable cutting elements that mount on tool holders such as turning bits, milling cutters or drills. Made from wear-resistant materials like carbide, cermet, ceramic or other superhard grades, they carry the actual cutting edge and allow a worn corner to be rotated or flipped instead of replacing or regrinding the entire tool body.
How these inserts work and when to choose them
In everyday workshop and production settings, indexable inserts perform the direct material removal on the workpiece. Standard inserts for tool systems without internal coolant typically feature closed faces or a single central fixing hole, with heat evacuation handled by external machine nozzles. Inserts designed for systems with internal coolant are engineered to support coolant flow: they include calculated chipbreaker geometries that guide an internal coolant jet under the chip or, in specialised designs, contain sintered microchannels to direct coolant right to the cutting edge. Such coolant-compatible inserts are essential for machining heat-resistant alloys, heavy cutting operations and deep internal machining, where thermal load and chip control are critical.
Tangible benefits for production and workshop efficiency
Choosing the right indexable inserts delivers measurable operational advantages:
- Reduced downtime: faster changeover because a worn insert is simply indexed rather than the whole tool being replaced.
- Extended cutting-edge life: targeted coolant application and optimised chipbreaker design lower thermal stress and improve tool life.
- Consistent part quality: predictable cutting-edge geometry from standardised inserts maintains tolerances across batches.
- Versatility: availability in carbide, cermet, ceramic and superhard grades permits selection according to workpiece material and cutting conditions.
- Lower tooling costs over time: fewer full-tool replacements and less regrinding required.
Metav as a dependable source for inserts and tooling systems
Metav combines decades of precision expertise with a wide-ranging supply chain, positioning itself as a practical partner for industry, craft and trade. From Emmerich on the Rhine, Metav operates as a quality filter for the European market, offering more than 250,000 products and serving over 48,000 customers. For procurement teams aiming to reduce supplier count while retaining technical reliability, Metav’s assortment of indexable inserts and compatible tool holders provides a central, trustworthy solution.
Quick summary
Indexable inserts (cutting inserts or indexable cutting inserts) enable economical, repeatable material removal by allowing worn cutting edges to be indexed or replaced quickly; coolant-adapted designs further reduce thermal load and enhance chip control for demanding applications.
FAQ
What materials are indexable inserts available in?
Indexable inserts are available in wear-resistant grades such as carbide, cermet, ceramic and other superhard materials, selected according to the workpiece material and cutting conditions.
When should I choose inserts with internal coolant support?
Choose inserts designed for internal coolant when machining heat-resistant alloys, performing heavy cuts or working in deep internal features, because the coolant reduces thermal load at the cutting edge and actively improves chip breakage.
How do chipbreaker geometries affect performance?
Chipbreaker geometries on indexable inserts guide the chip flow and, when matched to an internal coolant jet, direct the coolant under the chip to control temperature and facilitate reliable chip formation, which extends edge life and stabilises machining.
Can standard inserts be used with external coolant only?
Yes; standard inserts for tool systems without internal coolant typically have closed faces or a central fixing hole and rely on external machine nozzles for heat evacuation, which is sufficient for many routine, accessible cuts.
Why source inserts through Metav?
Metav supplies a broad range of indexable inserts and tooling, backed by decades of expertise and a comprehensive European stock, making it a practical choice for consistent quality and dependable delivery.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com