800mm Workshop Caliper With 300mm Jaws, Fine Adjustment, Monoblock, 0.05mm Vernier, Stainless Steel, Supplied In Case - Metav IndustryLine

Take advantage of the combination of robust stainless‑steel construction, an 800 mm measuring range and a precise fine‑adjustment mechanism for reproducible large‑format measurements in the workshop. Order the Metav IndustryLine Workshop Caliper M201.338.2 directly via Metav Werkzeuge or ask our consultants if needed.

Metav IndustryLine Workshop Caliper M201.338.2 — 800 mm stainless monoblock with fine adjustment

A robust Metav IndustryLine Workshop Caliper M201.338.2 engineered for heavy‑duty external, internal and step measurements up to 800 mm in demanding workshop environments

• Hardened stainless‑steel construction
• Monoblock design for high rigidity
• Fine‑adjustment wheel for precise setting
• Delivered in a protective transport case

Large‑range accuracy for heavy workshop work

The caliper offers an 800 mm range, placing it in the large‑range category for workshop measurement where profile stiffness and repeatability are decisive. The hardened stainless steel beam with a matt‑chromed scale resists wear and ensures legible graduations throughout its service life. With a vernier system reading of 0.05 mm and a combined inch/mm vernier — 1/128" (top) and 1/20 mm (bottom) — the instrument supplies a clear analogue indication that is well suited to routine quality checks and set‑up tasks on sizeable components. This configuration supports efficient process control where quick, verifiable readings are required without the need for electronic power.

Practical handling and repeatable results

A finely machined fine‑adjustment wheel allows slow, controlled closing of the jaws to the actual measuring faces, reducing the risk of overshoot and improving repeatability when setting to reference sizes. The monoblock design increases transverse stiffness, which lowers deformation during measurement and contributes to consistent readings over the entire measuring length. Pointed jaws are fitted for access to narrow recesses and for locating on specific features, while the hardened surfaces maintain dimensional integrity under frequent use. These mechanical advantages translate into measurable time savings and reduced rework in production and fixturing workflows.

Compliance, transport and workshop integration

The caliper is produced to match the referenced guideline DIN 862 (with specified conditions for jaw length), which underpins its suitability for industrial metrology routines. Delivery includes a protective transport case, appropriate for large instruments; for items of this scale the case is primarily intended for transport protection rather than long‑term storage. Marked technical identifiers and traceable codes simplify stockkeeping and integration into workshop tool inventories. For additional technical data or calibration queries, Metav’s specialists can supply extended details and support via email or telephone to ensure the instrument fulfils the specific application requirements.

Contact Metav Werkzeuge today to arrange supply of the Metav IndustryLine workshop caliper M201.338.2 and to benefit from expert advice and reliable delivery from Emmerich.

Technical data

• Article number: M201.338.2
• GTIN: 4054469101811
• ECLASS: 21170344
• Tariff number: 90173000

Facts

• Measuring range: 0–800 mm
• Jaw length: 300 mm
• Vernier readings: 1/128" (top) and 1/20 mm (bottom)
• Resolution / graduation: 0.05 mm
• Conformity note: DIN 862 (see jaw‑length conditions)

Special features

• Material: hardened stainless steel, matt‑chromed scale
• Monoblock construction for increased stiffness
• Fine‑adjustment mechanism for controlled setting
• Pointed jaws for access to narrow features
• Protective transport case included (for transport protection)

FAQ

What measuring tasks is this caliper best suited to?
The Metav IndustryLine Workshop Caliper M201.338.2 is intended for large‑format workshop measurements such as external, internal and step dimensions on fixtures, housings and clamping components up to 800 mm.

How precise is the analogue reading on this caliper?
The sliding scale provides a graduation of 0.05 mm and a dual vernier (1/128" top; 1/20 mm bottom), giving a robust analogue reading suitable for workshop tolerance checks and set‑up operations.

Does the instrument meet recognised standards?
Yes—the design and scale follow the conditions referenced in DIN 862, with applied requirements depending on jaw length as noted by the manufacturer.

Is the caliper supplied ready for immediate use and safe for transport?
The caliper is delivered in a protective transport case appropriate for large tools; the case is designed primarily for transport protection. For further handling or calibration details, Metav Werkzeuge can be contacted.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com