185mm Depth Extension For Internal Fine Measuring Gauge, Fits M208.022–024 / M208.052–054 - Metav IndustryLine

Take full advantage of the 185 mm extension to increase measuring depth while keeping handling simple and repeatable; the accessory’s compatibility with the M208.022–024 and M208.052–054 series and its low weight (0.2 kg) make it a practical solution for deeper measurements in small‑scale inspection tasks. Order the depth extension directly via Metav Werkzeuge or consult the technical team for integration advice.

185 mm Depth Extension — Accessory for Fine Measuring Instruments (M208.022–024 / M208.052–054)

A depth extension designed to extend the measuring reach of the fine measuring instruments in the M208 series, enabling reliable measurements at greater depth in assembly, inspection and tooling tasks.

• 185 mm additional measuring depth
• Fits M208.022–024 and M208.052–054 models
• Lightweight at 0.2 kg
• Simple retrofitting to existing gauges

Extend reach for reliable depth measurements

The 185 mm depth extension converts standard fine measuring instruments into a tool for deeper inspections without compromising handling. By adding measurable reach to the base instrument, the accessory enables precise depth readings where the original probe or jaw would fall short. This extension is intended for use in quality control, small‑batch production and toolroom checks where access to recessed features, bores or fixtures is required. The construction keeps added mass to a minimum to preserve the instrument’s balance and measurement behaviour, supporting repeatable results in typical workshop conditions.

Designed for fast retrofit and stable handling

Installation is optimised for straightforward fitment to the listed M208 series models, allowing technicians to adapt existing calibration routines quickly. The extension’s compact form and low weight simplify one‑person handling during inspection cycles and reduce the need for additional fixtures. Where consistency matters, retrofitting this accessory avoids the downtime and cost of acquiring separate long‑reach instruments—providing a pragmatic alternative that maintains the base instrument’s measurement characteristics while extending usable depth.

Practical use and workshop integration

Incorporating this depth extension into regular inspection procedures supports a more versatile measuring fleet without complex changes to process flow. The accessory is categorised as workshop‑grade measurement support for fine measuring instruments and functions as an add‑on to increase capability rather than a standalone calibrated device. For procurement and logistics, the compact size eases storage and handling; for application, it allows teams to measure recesses and internal features that would otherwise require specialised tools.

Contact Metav Werkzeuge to integrate this depth extension with existing M208 series instruments or to discuss suitability for specific measuring tasks

Technical Data

• Article number: M208.054.T
• GTIN: 4054469182322
• Weight: 0.2 kg
• Length: 185 mm
• Category: Fine measuring instruments accessory

Facts

• Additional measuring depth: 185 mm
• Compatibility: M208.022–024; M208.052–054

Special features

• Accessory for extending measuring depth
• Lightweight design for minimal impact on handling
• Intended for retrofit to existing fine measuring instruments
• Packaged as accessory (zubehör)

FAQ

How does the extension attach to existing instruments?
The depth extension is designed for direct fitment to the compatible M208.022–024 and M208.052–054 fine measuring instruments and is installed as a retrofit accessory to extend the probe reach.

Will adding the extension affect measurement repeatability?
The accessory’s low weight and purpose‑built geometry minimise disturbances; however, users should confirm repeatability within their specific test setup when the extension is fitted to any fine measuring instrument.

Is the extension a calibrated device?
The depth extension is an accessory and is supplied to extend measuring capability; it does not replace the calibration status of the base instrument. Calibration procedures remain focused on the complete measuring assembly where applicable.

Can the extension be used for internal and step measurements?
Yes; the extension increases reach for internal measurements and is suitable for stepped or recessed features when fitted to compatible fine measuring instruments.

Which models are supported by this accessory?
Compatibility is explicitly with the M208.022–024 and M208.052–054 series; check instrument mounting interfaces before procurement to ensure fit.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com