2000mm Assembly Rule Double‑T Aluminium‑Magnesium Alloy With Relief Holes, Grade 1 - Metav IndustryLine

Benefit from the combination of large-format reach, controlled flatness and reduced handling weight for consistent alignment of fixtures and assemblies; order the Assembly Straightedge M214.747 directly via Metav Werkzeuge or consult our advisors for application support.

Assembly Straightedge M214.747 — 2,000 mm Al‑Mg alloy, Grade 1 (Metav IndustryLine)

The Assembly Straightedge M214.747 is a 2,000 mm Grade 1 straightedge in an aluminium‑magnesium alloy, designed for precise alignment and fixture work in production and toolroom environments.

• Length 2,000 mm for large-format components
• Al‑Mg alloy construction, lightweight yet stiff
• Flatness 0.022 mm; parallelism 0.027 mm

Reproducible alignment across long spans

The long and rigid profile of this straightedge delivers reliable reference geometry for assembly, jigs and large components. With a verified flatness of 0.022 mm and parallelism of 0.027 mm, the bar preserves measurement integrity along its full length, reducing the need for repeated checks and lowering scrap rates. These tolerances make it particularly effective where reproducible planar references are required during setup or when aligning multiple sub‑assemblies.

Lightweight alloy benefits for frequent handling

Forged from an aluminium‑magnesium alloy, the tool balances low mass (6 kg) with sufficient stiffness for shop use; this reduces fatigue during repetitive positioning and simplifies two‑person handling. A hardness rating of HV 80 together with a specified yield strength of 110 kg/mm² and tensile strength of 47 kg/mm² indicate a material selection that resists everyday wear while remaining easier to manoeuvre than comparable steel alternatives. The inclusion of relief holes lowers the centre‑of‑gravity and enables secure clamping points without compromising the datum surface.

Designed for integration in workshop workflows

The straightedge’s cross‑section and 100 mm overall height provide an accessible datum for fixtures and alignment tools, while the 40 mm width keeps the profile compact for clamping into standard jig plates. At 2,000 mm length it addresses large assemblies without losing handling practicality; the measured weight and alloy choice support frequent use on benches and assembly rigs. Supplied as a Grade 1 tool, the component is suited to production and maintenance environments where consistent reference geometry shortens setup times and improves process repeatability.

For dependable alignment of large-format parts, request the Metav IndustryLine assembly straightedge via Metav Werkzeuge or contact our specialists for tailored advice at info@metav-werkzeuge.com or +49 2822 7131930

Technical Data

• Article number: M214.747
• GTIN: 4054469184548
• Manufacturer: Metav IndustryLine

Key dimensions

• Length: 2,000 mm
• Height: 100 mm
• Width: 40 mm
• Weight: 6 kg

Materials & features

• Material: Aluminium‑magnesium alloy
• Grade: Güte 1
• Flatness: 0.022 mm
• Parallelism: 0.027 mm
• Hardness: HV 80
• Yield strength: 110 kg/mm²
• Tensile strength: 47 kg/mm²
• Special feature: Relief holes

FAQ

What applications is this straightedge suited for?
The Assembly Straightedge M214.747 is intended for alignment, fixture setup and reference measurements on large components in production and toolroom environments; its 2,000 mm length suits assemblies and jigs requiring an extended datum.

How does the flatness value affect everyday use?
A flatness of 0.022 mm ensures that planar measurements and references remain consistent across the full length of the Metav IndustryLine straightedge, reducing rework and improving process repeatability.

Are the relief holes intended for clamping or weight reduction?
The relief holes on the Assembly Straightedge M214.747 serve both to reduce handling weight and to provide practical clamping or mounting positions when integrating the straightedge into jigs or assembly fixtures.

What material properties support durability during shop use?
The aluminium‑magnesium alloy, combined with a hardness of HV 80 and the indicated strength values, provides a balance of wear resistance and manageable weight for frequent handling in workshop conditions.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com