300mm Depth Gauge Digital Inductive Display mm/inch 0.01mm Resolution IP67 Plastic Case - Metav IndustryLine

Take advantage of a robust, workshop-ready digital depth caliper that pairs an inductive measuring system with IP67 protection for reliable results in daily production and inspection. The hardened stainless steel construction and DIN 862 conformity ensure long service life and traceable measurement practice — order the instrument directly via Metav Werkzeuge or ask the consultants for assistance.

M218.122 Depth Caliper — Digital depth gauge, 300 mm, IP67 (Metav IndustryLine)

The M218.122 Depth Caliper is a digital depth gauge designed for workshop and machine‑shop quality control, offering a 0–300 mm measuring range and a sealed enclosure for use in demanding production environments.

• IP67 dust and water protection
• Inductive measuring system for stable readings
• Hardened stainless steel construction
• Digital mm/inch display with 0.01 mm resolution

Consistent accuracy that speeds up inspection routines

The instrument provides a 0.01 mm resolution on a clear digital readout, reducing interpretation time and helping to avoid rework. The inductive measuring system minimises mechanical play and contact variability, which translates into fewer measurement errors and faster quality checks on the shop floor. Conformity with DIN 862 gives a standardised baseline for internal procedures and documentation, enabling comparability across batches and suppliers while supporting efficient process control.

Built to withstand workshop conditions and heavy use

A hardened stainless steel frame resists wear and maintains jaw geometry over time, so reproducibility is preserved even under frequent handling. The sealed construction rated IP67 protects the electronics from coolant, chips and dust, lowering downtime for maintenance. Supplied in a protective transport case, the gauge stays safe during storage and transfer between workstations — a practical detail that supports uninterrupted measurement workflows in production or maintenance settings.

Practical design for everyday metrology and traceability

With a 300 mm measuring range the tool fits the Standard caliper category, balancing reach and rigidity for common machine‑shop tasks such as checking bores, recess depths and component seats. The digital display toggles between mm/inch, simplifying cross‑standard checks and documentation. Lightweight at approximately 0.6 kg, the device is easy to position for repetitive depth measurements while providing the stability required for reliable results.

For robust depth measurement in production and inspection, choose the Metav IndustryLine M218.122 and contact Metav Werkzeuge in Emmerich for personalised advice and rapid supply — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930

Technical data

• Article number: M218.122

• GTIN: 4054469146188

• Manufacturer: Metav IndustryLine

• Measuring range: 0–300 mm

• Resolution (display): 0.01 mm / 0.0005 in

• Weight: 0.6 kg

• Protection rating: IP67

• Material: hardened stainless steel

• Measuring system: inductive

• Display: digital with mm/inch and 0/ON/OFF button

• Standard: DIN 862

• Tariff number: 90173000

FAQ

What measuring tasks is this depth caliper best suited for?
This depth caliper is optimised for standard workshop tasks such as depth checks on bores, recesses and seats up to 300 mm, offering a practical balance between reach and stiffness.

How does the inductive measuring system improve results?
The inductive measuring system reduces mechanical play and stabilises the signal, so readings from the M218.122 are less affected by operator contact forces and repeat more reliably.

Is the caliper protected against coolant and dust?
Yes, the device is rated IP67, which protects the electronics from dust ingress and temporary immersion, making it suitable for harsher production environments.

Can measurements be read in inches as well as millimetres?
The digital readout switches between mm/inch, enabling straightforward checks and documentation for mixed‑unit workflows.

Does the device comply with recognised measurement standards?
The instrument is compliant with DIN 862, providing a consistent basis for workshop metrology and internal quality procedures.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com