300mm Digital Precision Caliper With Preset, Stainless Hardened, Removable Measuring Inserts, Supplied In Case - Metav IndustryLine

Take advantage of a slim, purpose-made measuring insert that combines a flat measuring face with corrosion‑resistant construction and direct compatibility with the Digital‑Uni caliper series 240.201–240.204; order supply or request advice through Metav Werkzeuge for fast technical support. M240.261 — Measuring insert for groove measurement, flat measuring face, 40 mm (Metav IndustryLine) The M240.261 is a 40 mm stainless steel measuring insert designed for precise groove measurement on Digital‑Uni calipers series 240.201–240.204, offering a flat contact surface and slim profile for narrow access. Flat measuring face for parallel contact Slim profile for confined grooves Stainless steel, corrosion‑resistant Accurate groove measurements where space is limited The slim measuring tip and flat measuring face provide a reliable contact geometry for narrow grooves and shoulder features, reducing measurement scatter and supporting repeatable readings. With a contact area of 8×4×0.5 mm, the insert stabilises the probe-to-workpiece interface and helps produce consistent results when checking slot widths or internal recesses. This focused design is particularly useful in routine workshop inspections and small-series quality control, where efficient, verifiable measurements increase throughput without compromising traceability. Robust material and low maintenance for daily use Constructed from stainless steel, the insert resists corrosion and wear in typical shop environments, which reduces downtime for replacement and maintenance. The solid build and compact 40 mm length deliver a stable feel during handling while remaining light at 0.1 kg, easing repetitive use. These attributes translate into lower total cost of ownership through fewer tool changes and reliable long‑term service life in metalworking and assembly contexts. Seamless integration with Digital‑Uni calipers to speed workflows Engineered for direct fitment to the Digital‑Uni caliper series 240.201–240.204, the insert simplifies tool swaps and reduces setup time on the shop floor. Compatibility with the caliper family ensures measured values remain traceable within existing metrology equipment chains and allows teams to maintain a consistent measuring strategy across different stations. The short installation time and standardised interface support lean inspection processes and quicker decision cycles. Practical handling and application benefits At 40 mm overall length and with a narrow contact geometry, the insert reaches into grooves, steps and recesses that standard jaws cannot access, facilitating internal measurements without complex fixtures. The modest dimensions and corrosion‑resistant surface make cleaning and visual inspection straightforward, aiding calibration routines and keeping inspection intervals efficient. Marked repeatability and the clear contact specification help technicians interpret results with confidence and document quality checks for audits. Choose the Metav IndustryLine M240.261 for dependable groove measurements and contact Metav Werkzeuge in Emmerich for technical advice or to arrange supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M240.261 SKU: M240.261 GTIN: 4061905053863 Manufacturer: Metav IndustryLine Facts Measuring face: 8 x 4 x 0.5 mm Length: 40 mm Weight: 0.1 kg Special features Flat measuring face For groove measurement and internal recesses Compatible with Digital‑Uni calipers series 240.201–240.204 Corrosion‑resistant stainless steel construction FAQ How does the insert fit the caliper? The M240.261 is designed for direct compatibility with Digital‑Uni calipers (series 240.201–240.204) and connects via the caliper’s accessory interface for straightforward installation. What are the contact area dimensions? The measuring face measures 8 x 4 x 0.5 mm, providing a defined, flat contact for groove checks with the M240.261 insert. Is the insert suitable for use in humid or oily environments? Yes — the stainless steel construction of the insert offers corrosion‑resistant properties that make it suitable for typical workshop and production environments. Can this insert access very narrow slots? The slim profile and 40 mm length enable access into confined grooves and recesses where standard jaws are unsuitable, supporting internal groove and step measurement tasks. Is the insert repeatable for quality control tasks? The flat contact geometry and defined measuring face support repeatable readings, making the insert appropriate for routine inspection and traceable quality checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Compact and robust, the insert pairs a flat measuring face (8×8×0.8 mm) with a narrow beak engineered for precise groove contact, delivering repeatable results on profile and slot measurements. Order the M240.262 measuring insert directly via Metav Werkzeuge or ask our consultants for fitting advice and application support. M240.262 measuring insert for groove measurement — flat 8×8×0.8 mm face, 60 mm (Metav IndustryLine) The M240.262 measuring insert is a precision caliper accessory designed for groove measurement and fine slot inspection, compatible with Digital Uni caliper series 240.201–240.204. Narrow beak for groove measurement Flat measuring face 8×8×0.8 mm Length 60 mm for extended reach Stainless steel construction Precision where grooves matter The M240.262 is crafted to turn a standard caliper into a specialist gauge for slots and grooves. The flat measuring face with dimensions 8×8×0.8 mm ensures a stable contact area that reduces local deflection and improves reproducibility compared with pointed probes. Together with the narrow beak, this geometry grants improved access to tight grooves and narrow recesses, resulting in clearer contact definition and fewer ambiguous readings during quality checks. The design supports consistent alignment against slot shoulders, which aids traceable inspection routines in small-batch production or workshop quality control. Built for reliable workshop use Made from stainless steel, the insert is corrosion-resistant and tolerant to routine workshop environments, helping to maintain measurement integrity over repeated use. At approximately 0.1 kg, the component is lightweight yet stiff enough to avoid significant bending when used for typical hand-held caliper checks. The robust material and simple geometry make cleaning and visual inspection straightforward, which reduces downtime and supports fast changeover between measuring tasks. These attributes contribute to lower maintenance demands and longer service life for the caliper setup. Seamless fit and practical applications Compatibility with the Digital Uni caliper series 240.201–240.204 ensures straightforward integration without special adapters, extending the caliper’s capability to groove and slot inspection. As a caliper accessory, it is well suited to machining shops, tool rooms and component inspection where grooves, keyways or narrow recesses require rapid verification. The insert supports routine dimensional checks as part of in-process control or final inspection, enabling efficient workflows and clearer pass/fail decisions for repetitive features. Choose the Metav IndustryLine M240.262 for dependable groove measurement — contact Metav Werkzeuge in Emmerich for stock status, compatibility guidance and specialist application advice. Technical Data SKU: M240.262 GTIN: 4061905053870 Category: Caliper accessory Facts Length: 60 mm Flat face dimensions: 8×8×0.8 mm Weight: 0.1 kg Material: stainless steel Special features Narrow beak for groove measurement Flat measuring face for stable contact For Digital Uni caliper series 240.201–240.204 Suitable for slot and groove inspection FAQ What is the M240.262 intended to measure? The M240.262 is intended for groove and slot measurement, improving contact stability when inspecting narrow recesses and keyways with a compatible caliper. Which calipers is this insert compatible with? This insert fits the Digital Uni caliper series 240.201–240.204 and converts those instruments into dedicated groove-measurement tools. What material is the insert made from and why is that relevant? The insert is made from stainless steel, offering corrosion resistance and durable contact surfaces that preserve measurement accuracy during regular workshop use. How does the flat measuring face improve results? A flat measuring face of 8×8×0.8 mm increases the contact area against slot shoulders, reducing local deformation and improving the repeatability of readings compared with finer-point probes. Is the insert suitable for production inspection tasks? Yes, the M240.262 is designed for repetitive groove and slot checks in machining and inspection environments, supporting efficient in-process control and quality assurance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, precision‑engineered measuring insert that combines durable stainless steel construction with a defined 60 × 8 mm contact area for consistent external measurements; this replacement part restores original accuracy and keeps inspection workflows running without unnecessary downtime. Order the measuring insert directly via Metav Werkzeuge or request advice from our consultants if further help is needed. M240.264 measuring insert for external measurement — 60×8 mm, stainless steel (Metav IndustryLine) The M240.264 is a dedicated measuring insert for external measurement, designed for use with Digital‑Uni calipers in the 240.201–240.204 series and intended to restore accurate contact geometry in compact workshop and production environments. Precision-cut stainless steel insert 60×8 mm Fits Digital‑Uni calipers 240.201–240.204 Replacement part for reliable external measurement Lightweight design for straightforward handling Restores repeatable external measuring points for inspection tasks The replacement insert delivers a precisely defined contact face that supports repeatable measurement results on compact calipers. Manufactured from stainless steel, the component maintains its geometry under frequent use and resists common workshop contaminants. By reinstating the original contact area of the caliper head, the insert helps preserve traceable readings and reduces measurement scatter that can arise from worn or damaged jaws. The measured contact width of 60 × 8 mm provides a stable bearing for flat surfaces, improving stability during routine checks. Built for workshop durability and predictable service life A corrosion‑resistant stainless construction reduces the need for frequent part swaps and protects the contact surface against pitting and wear in standard industrial atmospheres. The modest mass and compact form factor aid handling during replacement and minimise added inertia that might affect delicate setups. These characteristics translate into fewer interruptions to production and longer intervals between maintenance operations, which is particularly valuable in busy inspection benches or when performing batch checks. Quick replacement and assured compatibility with existing calipers The insert is produced to fit the Digital‑Uni caliper family 240.201–240.204, enabling fast retrofitting without special tools. The design intent is to provide a reliable fit so that alignment and zeroing are straightforward after installation, reducing downtime. For operators managing multiple calipers, having a spare M240.264 on the bench ensures continuity of measurement tasks and avoids ad‑hoc repairs that can introduce uncertainty to quality control procedures. Ideal use cases and the measurement class it supports With a contact length of 60 mm, the insert is suitable for compact external measuring tasks typically performed with small calipers used in fine mechanical and general workshop contexts. This dimension aligns with the compact (micro) category of caliper work where short, stiff jaws deliver the best compromise between reach and rigidity. The part is therefore well suited to shopfloor checks, assembly inspection and service replacement where consistent external measurement is the priority. Contact Metav Werkzeuge today to obtain the M240.264 insert or to discuss compatible measurement accessories and replacements with our Emmerich team Technical data Article number: M240.264 GTIN: 4061905053887 Designation: Measuring insert for external measurement, 60×8 mm Manufacturer: Metav IndustryLine Core specifications Length: 60 mm Width: 8 mm Material: stainless steel Weight: 0.1 kg Features Compatible with Digital‑Uni calipers series 240.201–240.204 For external measurements Replacement measuring insert Corrosion‑resistant finish FAQ Is the insert compatible with Digital‑Uni calipers 240.201–240.204? The M240.264 is manufactured to fit Digital‑Uni calipers in the 240.201–240.204 series and provides a direct replacement for the external measuring face. What material is used for the measuring face? The measuring insert M240.264 is made from stainless steel, offering corrosion resistance and stable contact geometry for repeated measurements. Can the M240.264 be used for internal measurements? No, the M240.264 is designed specifically for external measurement applications and restores the caliper's external contact surface. How does the insert affect measurement consistency? By replacing worn contact geometry, the M240.264 restores repeatable bearing and helps reduce measurement scatter during routine external checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Robust stainless-steel measuring insert for reliable gauge mounting: the compact 60 × 4 mm body with an M2.5 threaded mount provides secure integration into Digital‑Uni caliper systems while keeping mass and thermal influence low. Order the M240.265 directly via Metav Werkzeuge or consult our advisors for application guidance. M240.265 — Precision measuring insert for digital calipers, stainless steel, M2.5 The M240.265 is a measuring insert designed to accept dial‑ or gauge‑type inserts, offering a compact 60 × 4 mm mounting face with an M2.5 threaded connection for use with the Digital‑Uni‑Caliper series 240.201–240.204. Stainless steel construction M2.5 threaded mounting 60 x 4 mm compact mounting face Compatible with Digital‑Uni‑Caliper series 240.201–240.204 Secure mounting for consistent measurement results A stable interface between gauge insert and caliper is essential for repeatable readings; the M240.265 provides precisely machined seating that reduces axial play and wobble. The M2.5 threaded mount secures common indicator inserts used in workshop metrology, which helps maintain contact force and alignment during inside, outside and depth measurements. By eliminating unintended movement at the gauge seat, the insert supports lower measurement scatter and a more reliable quality control process. Compact design that simplifies integration and handling With a nominal face of 60 x 4 mm and a mass of just 0.1 kg, the insert is optimised for compact digital caliper systems where space and balance matter. The small footprint minimises reach‑related deflection, preserving the overall stiffness of the measuring assembly and making it suitable for fine mechanical tasks and routine shop measurements. Low weight and a slim profile also facilitate quick replacement and tool changes in production environments without disturbing the instrument’s ergonomics. Corrosion resistance and long service life Manufactured from stainless steel, the insert resists corrosion and surface wear that can otherwise degrade seating geometry over time. The material choice reduces maintenance intervals and keeps the mating surfaces dimensionally stable even in humid or mildly contaminated workshop atmospheres. For operations that demand durable accessories that remain accurate under frequent use, this accessory contributes to predictable long‑term performance. Designed for practical metrology workflows Intended primarily for the Digital‑Uni‑Caliper family 240.201–240.204, the insert functions as a straightforward accessory to expand the measuring capabilities of existing instruments. The compact mounting face and standard thread allow repair shops, inspection benches and small series production to adapt calipers to specific measurement tasks quickly, supporting efficient setup and reduced downtime while preserving instrument traceability. Contact Metav Werkzeuge today to order the M240.265 or to request application advice from our precision specialists. Technical data Article number: M240.265 GTIN: 4061905053894 Facts Length: 60 mm Diameter: 60 x 4 mm Weight: 0.1 kg Thread: M2.5 Special features Material: stainless steel Compatible with Digital‑Uni‑Caliper series 240.201–240.204 Acceptance for dial/gauge inserts FAQ What is the primary function of this measuring insert? The M240.265 is a mounting insert that accepts dial‑ or gauge‑type inserts, enabling their use with Digital‑Uni‑Caliper series 240.201–240.204 for precise contact measurements. What material is the insert made from? The insert is manufactured from stainless steel, chosen for corrosion resistance and dimensional stability under workshop conditions. What are the key dimensions and thread specification? The mounting face measures 60 x 4 mm, the overall length is 60 mm and the threaded connection is M2.5; weight is 0.1 kg. Is the insert limited to the listed caliper series? The M240.265 is specified for Digital‑Uni‑Caliper series 240.201–240.204; it may also be compatible with other instruments that accept M2.5 gauge inserts, subject to confirmation of mating geometry. How can the part be identified for procurement or traceability? Identification is possible via the article number M240.265 and GTIN 4061905053894 for ordering and stock control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of robust stainless steel construction and large 25 x 20 mm jaws for reliable contact on broader workpieces; the compact insert provides a precise, repeatable fit and straightforward replacement. Order the M240.266 measuring insert directly via Metav Werkzeuge or ask our consultants if needed. M240.266 measuring insert for Digital‑Uni calipers — large jaws, stainless steel A M240.266 measuring insert designed to extend jaw reach and improve contact consistency for Digital‑Uni digital calipers in workshop and quality‑control environments. Large 25 x 20 mm measuring jaws Precision stainless steel construction Compatible with Digital‑Uni series 240.201–240.204 Compact replacement insert, workshop fit Stable contact for larger surfaces and assemblies The large jaw footprint delivers a more secure contact surface when measuring uneven or larger components. The 25 x 20 mm jaw geometry increases contact area, reducing local deformation and lowering the risk of slippage during measurement. Constructed from stainless steel, the insert resists corrosion and retains dimensional stability in workshop conditions, which supports consistent measurement results across repetitive checks. Precision fit that keeps inspections efficient Manufactured to tight tolerances, the insert ensures a repeatable connection with the caliper head and thus predictable measurement behaviour. Low mass and compact geometry improve handling without adding bulk; the item weight of 0.1 kg contributes to ease of use while preserving the rigidity needed for accurate readings. The result is reduced setup time and fewer discarded readings during routine inspections, supporting efficient production and quality workflows. Seamless integration into digital-caliper workflows Compatibility with the Digital‑Uni series 240.201–240.204 allows straightforward replacement and minimal downtime when a specialised jaw profile is required. The insert adapts existing digital calipers for measurements on broader contact faces, enabling technicians to switch between standard and large‑jaw configurations quickly. Clear model compatibility simplifies procurement and ensures the accessory supports established metrology procedures. Contact Metav Werkzeuge today for matching accessories or model advice — Metav IndustryLine components are stocked and quality‑checked in Emmerich to ensure timely delivery and consistent fit Technical data Article number: M240.266 GTIN: 4061905053900 Brand: Metav IndustryLine Facts Weight: 0.1 kg Jaw dimensions: 25 x 20 mm EClass: 21170324 Special features Material: stainless steel Compatible with Digital‑Uni caliper series 240.201–240.204 Intended use: replacement measuring insert for digital calipers Images and technical drawing available FAQ What models is this measuring insert compatible with? The M240.266 measuring insert is compatible with the Digital‑Uni caliper series 240.201–240.204 and is designed for straightforward replacement on those digital caliper heads. Will the stainless steel construction resist workshop corrosion? Yes, the stainless steel material used for the insert ensures good corrosion resistance and long‑term dimensional stability under normal workshop conditions. Can the large jaws be used for precision quality checks on flat surfaces? The larger 25 x 20 mm jaws increase contact area and improve stability on broader flat surfaces, making the insert suitable for repeatable quality checks where a wider contact face is advantageous. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a corrosion‑resistant stainless steel spare that restores precise contact with a round Ø 5 mm measuring pin and a practical 60 mm pin length, ensuring consistent results when replaced in compatible calipers; order the part directly via Metav Werkzeuge or consult our specialists for installation advice. M240.267 — Measuring insert for Digital‑Uni calipers, Ø 5 mm round pin M240.267 is a stainless steel measuring insert intended as a direct spare for Digital‑Uni calipers series 240.201–240.204, providing a durable, precise contact point for routine workshop measurements. Stainless steel construction Ø 5 mm round measuring pin Compatible with Digital‑Uni 240.201–240.204 Precision restored with a purpose‑made contact tip The exchange insert delivers a clean mechanical interface designed to return a caliper to repeatable measurement behaviour. The Ø 5 mm round pin concentrates contact force on a predictable surface, reducing wobble during small‑diameter checks and helping to maintain measurement stability. Manufactured in stainless steel, the tip resists corrosion and wear, which contributes to sustained precision over many cycles and reduces the need for frequent replacements. Durable materials for workshop conditions Constructed from stainless steel, this spare is specified to withstand typical shop environments where oils, coolants and handling can accelerate wear. The 60 mm pin length is balanced for accessibility without compromising rigidity, translating into fewer re‑checks and faster inspection loops; the modest mass also keeps handling straightforward. Together these properties deliver a reliable, low‑maintenance component that supports production continuity and longer service intervals. Practical spare and simple retrofitting As a purpose‑built measuring insert for the Digital‑Uni series, the component is designed for straightforward replacement with standard workshop tools, enabling fast downtimes and minimal instrument out‑of‑service time. The lightweight construction eases handling during fitment. For customers maintaining a fleet of calipers, stocking this spare part supports predictable maintenance planning and reduces interruptions in quality control procedures. For retrofit parts or technical support on Metav IndustryLine measuring inserts, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss fitment and delivery options Technical Data Article number: M240.267 GTIN: 4061905053917 Material: Stainless steel Weight: 0.1 kg Measuring pin Ø: 5 mm Pin length: 60 mm Overall length: 70 mm Facts Compatible series: Digital‑Uni 240.201–240.204 Measuring range outside: 0‑X Measuring range inside: 10‑X Special features Round measuring pin Corrosion‑resistant stainless steel Lightweight spare part for calipers FAQ What calipers does this insert fit? This insert fits the Digital‑Uni calipers series 240.201–240.204 and is supplied as the Metav IndustryLine spare part M240.267. Is the measuring pin resistant to corrosion? Yes, the measuring pin is made of stainless steel, which provides corrosion resistance suitable for standard workshop conditions. Can this insert be fitted without special tools? The insert is designed for straightforward retrofitting using common workshop tools and can be replaced quickly to minimise instrument downtime. What are the dimensions of the pin and its length? The pin diameter is Ø 5 mm and the contact pin length is 60 mm; the overall part length is 70 mm. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of a flat 1 x 0.4 mm measuring face, corrosion‑resistant stainless steel construction and a compact L = 12 mm tip for reliable groove and slot measurement. Order the accessory directly via Metav Werkzeuge or consult our specialists for application advice and compatibility checks. M240.211 interior measuring insert — flat 1 x 0.4 mm tip for Digital‑Uni calipers The M240.211 interior measuring insert is a precision flat‑faced inside measuring tip intended for accurate slot and groove measurement on Digital‑Uni calipers series 240.201–240.205, suitable for inside measurements starting at 5 mm. Flat 1 x 0.4 mm measuring face Fits Digital‑Uni calipers series 240.201–240.205 Designed for inner measurements from 5 mm Stainless steel construction Precision contact for narrow grooves and slots The insert provides a flat measuring face of 1 x 0.4 mm, enabling stable contact in narrow grooves where a pointed tip would slip or deform the part. The small, flat contact area reduces local deformation and contact uncertainty, which improves repeatability when checking multiple identical features. Manufactured from stainless steel, the tip maintains its geometry under frequent use and resists corrosion, ensuring consistent dimensional control for workshop and inspection tasks. Robust design that keeps measurement workflow efficient A compact tip length of L = 12 mm gives access into confined recesses while keeping the lever arm short to limit bending and play; this improves handling and supports quick, one‑person measurement routines. The modest mass of the insert reduces inertia on the caliper slide, helping to preserve the instrument's original feel and accuracy. Because the accessory is engineered for routine industrial use, the result is fewer re‑measurements and a faster quality control loop. Seamless integration with Digital‑Uni calipers for dependable results The insert is made specifically for the Digital‑Uni calipers series 240.201–240.205, so mechanical fit and alignment are assured and calibration offsets remain minimal after fitting. That compatibility streamlines tool management: the measuring tip becomes a simple, replaceable extension of the caliper's functionality, ideal for workshops that require both general‑purpose and specialised inside measurements without investing in separate gauges. For groove and slot measurement tasks that demand repeatable contact and corrosion resistance, request the Metav IndustryLine M240.211 interior measuring insert from Metav Werkzeuge — contact our Emmerich team by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for technical clarification and delivery options. Technical Data Article number: M240.211 GTIN: 4061905053689 Brand: Metav IndustryLine Facts Weight: 0.04 kg Measuring face: 1 x 0.4 mm Tip length L: 12 mm Inner measurement from: 5 mm Special features Material: stainless steel Flat measuring face for groove measurement Compatible with Digital‑Uni calipers series 240.201–240.205 Intended for inside measurements and slot inspection FAQ What is the primary purpose of this measuring insert? The M240.211 insertion tip is designed for precise groove and slot measurement, providing a flat contact surface that improves stability and repeatability when measuring internal features. Which calipers are compatible with the insert? Compatibility is specified for the Digital‑Uni calipers series 240.201–240.205; the M240.211 is manufactured to fit those models and align with their measuring axis. What material is the insert made from and why does that matter? The insert is made of stainless steel, which preserves tip geometry under repeated use and provides corrosion resistance, helping to maintain consistent measurement results over time. Is a calibration certificate supplied with the insert? The M240.211 is an accessory part; a calibration certificate is not automatically included unless explicitly stated on the product labelling or order documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combine compact, flat measuring faces with stainless‑steel robustness for reliable internal and groove measurement; benefit from simple retrofitting to existing Digital‑Uni calipers and order the insert directly via Metav Werkzeuge or consult our advisers for application support. Internal measuring insert M240.212 – flat measuring faces 2 x 0.4 mm, for Digital‑Uni calipers (Metav IndustryLine) An Internal measuring insert M240.212 designed for precise internal and groove measurements on Digital‑Uni calipers series 240.201–240.205 Flat measuring faces 2 x 0.4 mm Suitable for internal measurements from 7 mm Precision stainless steel construction Compatible with Digital‑Uni calipers series 240.201–240.205 Precise groove and slot measurement where space is tight The compact measuring tip is engineered for internal measurement in confined geometries. The flat measuring faces (2 x 0.4 mm) concentrate contact on narrow edges, which reduces tilting and improves repeatability when checking grooves, slots and bores that start at about 7 mm. This design translates into faster inspection loops in small‑batch production: fewer re‑measures, clearer go/no‑go decisions and a lower risk of damaged workpieces or wasted cycles. Robust construction for consistent results Manufactured from stainless steel, the insert offers corrosion resistance and mechanical stability that support long‑term repeatability. At a low mass, the attachment minimises added inertia on the caliper slide, maintaining the instrument’s tactile handling. The metal finish also keeps wear to a minimum on the contact faces, which preserves the nominal geometry and reduces drift over repeated cycles — a direct benefit to process control and measurement traceability. Seamless compatibility with Digital‑Uni calipers for workshop efficiency This measuring insert fits the Digital‑Uni caliper series 240.201–240.205 and is supplied under SKU M240.212, enabling quick swaps between different tip geometries without bespoke adapters. For workshops and quality departments, the modular approach reduces tool changeover time and supports a standardised inspection setup across multiple machines or benches. The result is measurable time savings during set‑up and inspection, supporting higher throughput without sacrificing accuracy. Contact Metav Werkzeuge today to confirm fitment for your calipers, request availability of the M240.212 insert and receive tailored advice from our technical team at Metav Werkzeuge Technical data Article number: M240.212 GTIN: 4061905053696 Manufacturer: Metav IndustryLine Core technical data Weight: 0.04 kg Measuring faces: 2 x 0.4 mm Inner measurement range: from 7 mm Special features Material: stainless steel Application: groove and internal measurements Compatibility: Digital‑Uni calipers series 240.201–240.205 SKU: M240.212 FAQ How small an internal diameter can be measured with this insert? The insert supports internal measurements starting at approximately 7 mm thanks to its narrow flat measuring faces. Is the insert suitable for groove and slot checks? Yes, the flat measuring faces (2 x 0.4 mm) are specifically designed to measure grooves and narrow slots with improved contact stability. Which calipers is this insert compatible with? Compatibility is specified for the Digital‑Uni calipers series 240.201–240.205; the item is supplied as M240.212 for those models. What material is the measuring tip made from? The measuring insert is manufactured from stainless steel to ensure corrosion resistance and stable measurement behaviour. Does the product data indicate calibration is included? The product data does not specify a calibration certificate; calibration status is not indicated for this insert. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of flat measuring face geometry and stainless steel durability to measure narrow grooves reliably from 15 mm; the compact profile and light weight ensure quick mounting on compatible digital calipers. Order the insert directly via Metav Werkzeuge or consult the Metav team for compatibility advice. Metav IndustryLine M240.213 internal measuring insert — flat 5 x 0.6 mm, L = 25, from 15 mm The M240.213 internal measuring insert for Digital Uni Calipers series 240.201–240.205 extends internal measuring capability from 15 mm, offering precise groove and notch measurement in confined spaces. Flat measuring face 5 x 0.6 mm for narrow grooves For internal measurements starting at 15 mm Stainless steel construction for corrosion resistance Precise groove measurement in compact spaces The insert’s flat measuring face (5 x 0.6 mm) and short jaw length L = 25 mm were developed specifically for narrow groove and slot inspection. The slim contact geometry concentrates the measuring edge without enlarging the profile, which reduces the risk of interfering with neighbouring features; this results in more reproducible internal readings when used with a compatible digital caliper. The component’s form is particularly beneficial for quality control tasks where access is limited and repeatability is essential, such as assembly checks and finishing inspections. Robust, lightweight construction for reliable handling Made from stainless steel, the insert combines corrosion resistance with dimensional stability. At a weight of 0.04 kg, the accessory adds minimal mass to the caliper, maintaining the instrument’s balance and ease of use during repetitive measurement cycles. The durable material reduces maintenance needs and prolongs service life in workshop environments, while the compact design supports fast tool changes and secure clamping on the caliper jaw, improving throughput in routine inspection processes. Compatibility and practical application in production Designed for direct installation on the Digital Uni Calipers series 240.201–240.205, the insert enables internal measurements starting at 15 mm, making it suitable for groove, notch and small-diameter internal checks. The flat measuring surface improves contact on step-like geometries and prevents rocking that can occur with rounded jaws. In machining, toolroom and maintenance settings, the insert provides a pragmatic extension of a caliper’s functionality, reducing the need for separate specialised gauges and supporting faster in-process decisions. For advice on fitment and to procure the Metav IndustryLine M240.213 insert from Emmerich, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M240.213 GTIN: 4061905053702 Material: stainless steel Weight: 0.04 kg Length: 50 mm Facts Measuring face: 5 x 0.6 mm Measuring jaw length: L = 25 mm Internal measurement from 15 mm Suitable for groove and notch measurements Special features Compatible with Digital Uni Calipers series 240.201–240.205 Flat measuring surface for narrow grooves Lightweight design for easy handling FAQ What tasks is the insert intended for? The Metav IndustryLine M240.213 internal measuring insert is intended for narrow groove, notch and small internal-diameter measurements beginning at 15 mm when fitted to Digital Uni Calipers series 240.201–240.205. Is the insert resistant to corrosion? Yes. The measuring insert is manufactured from stainless steel, providing corrosion resistance and stable performance in workshop and production environments. Will the insert affect caliper handling significantly? No. At 0.04 kg the accessory is lightweight and maintains the caliper’s balance, enabling reliable manual handling during repetitive inspection sequences. Can the insert be used for step and slot checks? Yes. The flat 5 x 0.6 mm measuring face and 25 mm jaw length are optimised for step-like geometries, narrow slots and grooves where a slim contact area improves measurement repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a precise, durable measuring accessory that extends the capability of existing digital calipers for groove and internal profile inspection. The stainless steel construction and flat measuring face (6.5 × 1 mm, L = 30 mm) provide reproducible contact geometry and long service life. Order the insert directly via Metav Werkzeuge or consult the team for application advice. M240.214 Inside Measuring Insert for Digital‑Uni Calipers – Flat 6.5 × 1 mm, L 30 mm A M240.214 inside measuring insert designed to equip Digital‑Uni calipers for accurate groove and internal profile measurement from 20 mm upwards Flat measuring face 6.5 x 1 mm Compatible with Digital‑Uni series 240.201–240.205 Stainless steel construction for longevity Intended for internal measurements from 20 mm Precise contact geometry optimised for groove measurement The insert features a flat measuring face of 6.5 × 1 mm and an effective contact length of 30 mm, a combination that narrows the contact area to a stable, repeatable surface for groove and slot inspection. This geometry reduces measurement scatter on narrow features and converts the basic caliper into a specialised internal probe for profile checks. The result is improved reproducibility when comparing production parts against drawings or gauges, enabling faster go/no‑go decisions on the shop floor. Robust stainless construction for reliable duty Manufactured from stainless steel, the insert resists corrosion and maintains dimensional stability in typical workshop atmospheres. The material choice supports regular use and cleaning without surface degradation, which preserves the calibrated contact geometry over time. Because the part is small and mechanically simple, wear is limited to contact areas; periodic inspection suffices to confirm ongoing accuracy, making maintenance straightforward and cost‑effective in continuous production environments. Fast retrofit to Digital‑Uni calipers for workflow efficiency Designed specifically for the Digital‑Uni caliper family (series 240.201–240.205), the insert delivers a quick, tool‑free upgrade path for existing instruments. Retrofit capability allows established measuring routines to be extended without purchasing a dedicated specialised gauge, improving resource utilisation and reducing capital expense. The compatibility also preserves the digital readout and data capture workflow of the parent instrument, keeping inspection records consistent and traceable. Practical handling and application benefits in everyday use With a compact overall footprint and a mass of only 0.04 kg, the insert is easy to mount and manoeuvre within assemblies or confined areas. The narrow, flat face gives clear tactile feedback when seating into a groove, translating operator action into a reliable measurement trace. This accessory suits workshop and toolroom tasks where internal features start at 20 mm and precision is required without complex setup. For traceable inspection, the insert is supplied as an accessory for the caliper family and integrates into existing quality routines. Choose the Metav IndustryLine M240.214 insert to extend the capability of Digital‑Uni calipers with a corrosion‑resistant, groove‑optimised contact; contact Metav Werkzeuge for application advice or to request a quotation through the Emmerich quality centre Technical data Article number: M240.214 GTIN: 4061905053719 Weight: 0.04 kg Material: stainless steel Facts Measuring face: 6.5 x 1 mm Insert contact length: 30 mm Overall length: 54 mm Internal measurement start: from 20 mm Special features Compatible with Digital‑Uni calipers series 240.201–240.205 Flat measuring face for groove measurement Corrosion‑resistant construction Compact, light accessory for retrofit FAQ Can this insert be used with any digital caliper? The insert is designed specifically for the Digital‑Uni caliper family (series 240.201–240.205); use with other models may require adaptation or may not provide secure mounting. The M240.214 inside measuring insert is intended to preserve the original caliper fit and function. What types of features is the insert best suited to measure? This accessory is optimised for grooves, narrow slots and internal profiles where a flat measuring face improves contact repeatability. The M240.214 performs best on internal features starting at 20 mm and where a defined contact geometry is required. How does the flat measuring face improve measurement results? The 6.5 × 1 mm flat face concentrates contact to a stable surface, reducing rocking and undefined contact conditions in narrow slots. This yields more reproducible readings compared with blunt or rounded probes when assessing groove widths or profile dimensions. Is a calibration certificate supplied with the insert? The M240.214 is supplied as a measuring accessory; calibration status is managed at the instrument level. If a certified calibration is required for a complete measuring system, please clarify requirements when ordering so the appropriate calibration workflow can be arranged. What material is used and how does it affect longevity? The insert is made from stainless steel, offering corrosion resistance and dimensional stability under normal workshop conditions, which supports sustained accuracy and reduces the need for frequent replacement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Taking advantage of a flat measuring face (10 x 1.5 mm) and a compact stainless steel body, this internal measuring insert delivers precise groove and recess checks from 44 mm internal diameter; order the M240.215 insert directly via Metav Werkzeuge or consult our technical team for application guidance. M240.215 internal measuring insert for Digital‑Uni calipers — flat measuring face 10 x 1.5 mm M240.215 is an internal measuring insert designed for precise groove and recess measurement, compatible with the Digital‑Uni caliper series 240.201–240.205. Flat measuring face 10 x 1.5 mm for groove checks Internal measurement from 44 mm onward Stainless steel construction for corrosion resistance Compatible with Digital‑Uni calipers series 240.201–240.205 Accurate groove measurement for quality assurance The insert provides a flat measuring face that is 10 x 1.5 mm, specifically shaped to access narrow grooves and slots with repeatable contact. By concentrating the contact area, the design reduces tilting and measurement scatter, which translates into more consistent internal diameter readings. This targeted geometry benefits workshop and production environments where quick verification of recesses is required without swapping to specialist gauges. Durable stainless‑steel design for reliable results Manufactured from stainless steel, the insert resists corrosion and maintains its geometry through frequent use. The material choice supports stable thermal behaviour and eases cleaning after exposure to cutting fluids or shop contaminants, thereby safeguarding long‑term accuracy. With a compact mass of 0.1 kg and robust construction, the accessory remains rigid during measurement, helping to reduce operator‑induced variability and maintain process control. Fast integration into existing caliper workflows Engineered for straightforward mounting on the Digital‑Uni calipers (series 240.201–240.205), this insert simplifies tool changes and minimises downtime. The insert’s 80 mm active length and compatibility mean the caliper can be adapted quickly from external to internal groove measurement without additional instruments, supporting a more efficient inspection routine and a reduced error budget. This integration supports lean inspection flows and helps keep throughput steady. For precise groove and recess checks, request the M240.215 internal measuring insert from Metav Werkzeuge in Emmerich or get tailored advice from our technical consultants via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M240.215 SKU: M240.215 GTIN: 4061905053726 Material: stainless steel Facts Weight: 0.1 kg Overall length: 100 mm Measuring face: 10 x 1.5 mm Insert active length L: 80 mm Internal measurement from: 44 mm Special features Compatibility: Digital‑Uni calipers series 240.201–240.205 Application: groove and recess measurement Construction: flat measuring face for stable contact Finish: corrosion‑resistant stainless steel FAQ Is this insert suitable for measuring narrow grooves? Yes. The M240.215 insert features a flat measuring face (10 x 1.5 mm) that is specifically intended for groove and slot measurement, allowing stable contact and repeatable internal readings. Which calipers does the insert fit? The insert is compatible with the Digital‑Uni caliper series 240.201–240.205 and mounts to those units to enable internal groove and recess checks without additional adapters. What material is the insert made from and why does that matter? The insert is made from stainless steel, chosen for corrosion resistance and dimensional stability; this supports long‑term accuracy under normal workshop conditions. From what internal diameter can this insert be used? The design allows internal measurement from 44 mm onwards, making it suitable for medium‑sized bores, recesses and grooves within that range. Can this insert be used for external measurements? This accessory is designed for internal applications; external measurement capability is provided by the caliper body when fitted with the standard external jaws. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise internal and groove measurement with a compact, corrosion‑resistant probe that fits the Digital Uni Calipers series 240.201–240.205; order the accessory via Metav Werkzeuge or consult our specialists for integration advice. M240.221 Inside Measuring Insert — 2 x 1 mm probe, L 20 for Digital Uni Calipers (Series 240.201–240.205) The M240.221 inside measuring insert is an accessory designed to extend the internal measuring capability of digital uni calipers, enabling reliable groove and bore checks from 10 mm onward. 2 x 1 mm probe measuring faces Stainless steel construction Compatible with Digital Uni Calipers series 240.201–240.205 Compact design for narrow grooves and bores Precise internal and groove measurement for reliable results The insert provides a defined contact geometry with 2 x 1 mm probe faces and a probe length of L 20 mm, enabling measurements in narrow grooves and compact bores where standard jaws cannot reach. The small, flat probe surfaces reduce local deformation and ensure reproducible contact conditions, which supports consistent readings on the display. By converting hard-to-reach features into measurable surfaces, the accessory delivers a measurable improvement in inspection efficiency and traceability. Robust stainless‑steel design for workshop durability Manufactured from stainless steel, the insert resists corrosion and maintains dimensional stability under normal workshop conditions. With an overall length of 46 mm and a lightweight construction of 0.04 kg, the component adds negligible inertia to the caliper while providing a durable contact tip for repeated use. The combination of durable material and compact mass minimises thermal and handling influences, improving the repeatability of routine internal checks in machining and assembly environments. Seamless compatibility and straightforward handling The insert is engineered for direct fitment to the Digital Uni Calipers series 240.201–240.205, delivering a practical upgrade path without the need for custom adaptors. Installation is designed to be quick and secure, enabling fast changeover between standard jaws and the specialised probe. Metav’s position as a precision partner ensures that the accessory is stocked and delivered with clear identification, supporting traceable inventory and simplified tool management for workshops and quality departments. Speak to Metav Werkzeuge for tailored advice on integrating the M240.221 inside measuring insert with existing digital calipers and to confirm suitability for specific groove and bore inspection tasks Technical Data Article number: M240.221 GTIN: 4061905053733 Manufacturer: Metav IndustryLine Dimensions & Weight Overall length: 46 mm Probe length (L): 20 mm Probe measuring faces: 2 x 1 mm Weight: 0.04 kg Measuring range (internal): from 10 mm Measuring range (external): from 6 mm Compatibility & Features Compatible with Digital Uni Calipers series 240.201–240.205 Material: stainless steel Intended use: internal and groove measurements Compact probe for narrow features FAQ What is the primary use of this insert? The M240.221 inside measuring insert is intended for internal and groove measurements where standard caliper jaws cannot access the feature, converting narrow bores and slots into measurable contact surfaces. Which calipers is the insert compatible with? This insert is compatible with the Digital Uni Calipers series 240.201–240.205 and fits as a direct accessory to extend internal measuring capability. Are the probe faces suitable for very narrow grooves? Yes, the 2 x 1 mm probe measuring faces are designed specifically for narrow grooves and small bore features, offering defined contact geometry for repeatable readings. Is the insert corrosion‑resistant? The insert is manufactured from stainless steel, providing resistance to corrosion and ensuring dimensional stability under typical workshop conditions. How heavy is the accessory and does it affect caliper handling? At approximately 0.04 kg, the insert adds minimal weight, preserving the caliper’s balance and ease of handling during inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise internal measurement starting at 20 mm, a compact 5 × 2 mm pin measuring face and robust stainless‑steel construction for repeatable shop‑floor results; order the insert directly via Metav Werkzeuge or consult our advisors for integration support. Internal measuring insert M240.222 — stainless steel, 5×2 mm pin measuring face for Digital‑Uni calipers The Internal measuring insert M240.222 is an accessory for extending the internal measuring capability of Digital‑Uni calipers in the 240.201–240.205 series, enabling reliable measurement of bores and grooves from 20 mm upwards. Precision pin measuring face 5 x 2 mm Stainless steel construction for wear resistance Fits Digital‑Uni calipers series 240.201–240.205 Confident internal measurement for bores and grooves The insert converts a standard digital caliper into a specialised internal gauge for bores, slots and grooves starting from 20 mm, delivering a controlled contact area with its 5 × 2 mm pin measuring face. The reduced contact footprint permits access to narrow features while maintaining a defined seating point, which reduces measurement variability. Because the accessory is purpose‑made for internal checks, it supports quicker inspection cycles and fewer tool changes, helping to keep production flowing with measurable consistency. Robust stainless‑steel design for repeatable results Manufactured from stainless steel, the insert resists corrosion and abrasion encountered in typical workshop environments, so dimensional stability is preserved over repeated use. The modest mass contributes negligible inertia at the caliper jaws, while the construction ensures that the contact geometry remains intact under normal handling. These attributes together increase repeatability of internal measurements and lower the risk of wear‑induced deviation that otherwise necessitates frequent replacement or rework. Fast retrofit and reliable compatibility with existing calipers Engineered to match the mounting geometry of the Digital‑Uni series 240.201–240.205, the insert installs with minimal adjustment, reducing downtime during tool changes. The compact overall profile and a pin length of 40 mm balance reach and rigidity, while the overall length of 65 mm keeps handling comfortable. For workshops standardising inspection tooling, this accessory offers a pragmatic upgrade route that extends the capability of existing Digital‑Uni calipers without the need for additional dedicated instruments. For advice on integrating the Metav IndustryLine internal measuring insert into inspection routines, or to arrange supply from Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists will advise on compatibility and delivery. Technical data Article number: M240.222 GTIN: 4061905053740 Weight: 0.05 kg Material: rostfreier Stahl Length (overall): 65 mm Pin length: 40 mm Facts Internal measuring from 20 mm Pin measuring face: 5 x 2 mm Compatible series: 240.201–240.205 Weight: 0.05 kg Special features Stainless‑steel construction Designed for internal bore and groove measurement Retrofit for Digital‑Uni calipers Compact, low‑mass accessory for minimal inertia FAQ What measurement range does the insert cover? The insert enables reliable internal measurement from 20 mm upwards when mounted on the Digital‑Uni caliper series; the defined pin face is intended for bores and narrow grooves. Which calipers are compatible with this accessory? This accessory is made for Digital‑Uni calipers in the 240.201–240.205 range; the mount and dimensions match those models for a secure retrofit. What is the contact geometry of the measuring face? The measuring face on the insert is a 5 x 2 mm pin, offering a small, well‑defined contact area for repeatable internal checks. How durable is the insert in a workshop environment? Constructed from stainless steel, the insert resists corrosion and wear typical of shop use, preserving contact geometry and repeatability over time. How does the insert affect handling and balance of the caliper? With a low mass of 0.05 kg and compact dimensions, the accessory imposes minimal additional inertia, maintaining the caliper’s handling characteristics while extending its function. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the precise pin geometry and robust stainless steel construction for reliable groove and bore measurements; compatible with the Digital‑Uni caliper series for quick retrofitting. Order the insert via Metav Werkzeuge or consult the Metav team for application advice. M240.223 Inside measuring insert — pin measuring faces 10 x 2 mm, L=80 The M240.223 is an inside measuring insert designed to extend the inside‑measurement capability of Digital‑Uni calipers 240.201–240.205, ideal for groove and bore checks from 44 mm. Pin measuring faces 10 x 2 mm For inside measurements from 44 mm Stainless steel construction Compatible with Digital‑Uni calipers Precision slot and bore measurement with defined contact geometry The insert provides repeatable precision by using narrow pin measuring faces (10 x 2 mm) that access slots and grooves which standard jaws cannot reach. Fitted to the Digital‑Uni series, the accessory converts a general‑purpose caliper into a specialised inside gauge without altering the instrument’s core accuracy. The narrow contact pads reduce contact area, making it easier to locate and measure small recesses while preserving a stable reference point. Robust material and design for workshop use Made from stainless steel, the attachment resists corrosion and maintains its measuring edges during regular use. The compact mass (approx. 0.1 kg) and the defined insert length (L=80 mm as specified in the article description) ensure stable handling and minimal added flex when mounted. Because the insert is designed for inside measurements starting at 44 mm, it is particularly useful for slot, bore and groove inspection tasks in mechanical engineering and assembly lines where access is limited. Practical compatibility and workflow benefits Integration with the Digital‑Uni calipers series 240.201–240.205 keeps the measurement workflow efficient: no separate gauge set is required and familiar caliper handling is retained. The accessory supports faster inspection cycles and reduces the need for improvised fixtures, helping to cut measurement time while maintaining traceable results. When paired with a digital caliper, readings remain clear and can be recorded according to existing shop procedures. Trust and service from a precision partner Metav IndustryLine supplies this insert with the backing of a broad metrology programme: dependable supply, transparent ordering and expert advice from the Metav team. The product fits Metav’s mission to make precise measurement tools accessible and reliable for workshops and industry alike, supported by a European quality filter and customer service for technical queries. For compatibility checks, application advice or to request the M240.223 inside measuring insert, contact Metav Werkzeuge GmbH — Metav consultants provide practical assistance from Emmerich to keep inspection processes running smoothly. Technical data Article number: M240.223 GTIN: 4061905053757 Label: Inside measuring insert ab 44 mm, pin measuring faces 10 x 2 mm, L=80 for Digital‑Uni calipers series 240.201–240.205 Facts Measuring length L: 80 mm Weight: 0.1 kg Pin measuring faces: 10 x 2 mm Measuring range (inside): from 44 mm Special features Material: stainless steel Compatibility: Digital‑Uni calipers series 240.201–240.205 Intended for groove and bore inside measurements Compact accessory for enhanced caliper functionality FAQ How is the M240.223 attached to a caliper? The M240.223 attaches directly to Digital‑Uni calipers 240.201–240.205 by replacing or mounting on the existing inside jaws according to the series’ accessory interface, creating a secure measuring extension for slots and bores. Which measurements are best suited for this insert? The insert is intended for inside measurements from 44 mm and is optimised for narrow grooves, slots and bores where the 10 x 2 mm pin measuring faces provide a defined contact point and repeatable results. Is the material resistant to workshop conditions? Yes, the M240.223 is made of stainless steel, offering corrosion resistance and durability for routine workshop and production environments. Can the insert affect caliper accuracy? When correctly mounted on the compatible Digital‑Uni caliper series, the insert preserves the instrument’s measuring concept; the defined pin geometry supports repeatable contact without introducing undue flex or uncertainty. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of a ball-ended measuring face, a defined Ø4 mm contact and 70 mm reach to achieve reproducible external measurements; the stainless steel construction adds corrosion resistance for reliable workshop use. Order the part directly via Metav Werkzeuge or ask our consultants for compatibility details. M240.232 External measuring jaw insert — ball-ended Ø4 mm, 70 mm reach (Metav IndustryLine) The M240.232 external measuring jaw insert is an accessory for extending the external measuring capability of Digital Uni calipers, providing a ball-shaped contact for precise measurements from 42 mm and above on the associated caliper series. Ball-ended contact for defined contact point Ø4 mm contact diameter for small features 70 mm reach for extended measuring access Stainless steel for corrosion resistance Defined contact for reproducible external measurements The ball-shaped contact provides a defined contact that reduces variability when measuring edges or slightly curved surfaces. With a Ø4 mm contact diameter and a clear single-point interface, the insert gives repeatability that is superior to blunt or uneven contacts; this helps to reduce measurement scatter during routine quality checks and supports faster decision-making on shop-floor tolerances. The measured contact geometry also minimises indentation on softer finishes, preserving part integrity. Robust design that extends caliper functionality without compromise Made from stainless steel, the insert resists corrosion and stands up to regular workshop handling. The 70 mm reach of the measuring face adds measurable access without compromising stiffness, making the component suitable when the standard jaws cannot reach recessed features. Compatibility with the Digital Uni Calipers series 240.201–240.205 allows a straightforward retrofit: the part extends existing instruments with a reliable, metal contact that keeps calibration intervals predictable and maintenance simple. Practical benefits for production and inspection workflows Fitting the insert increases the versatility of a single caliper, reducing the need for multiple specialised gauges and supporting leaner toolsets in inspection stations. The defined ball contact improves measurement confidence on edges, grooves and rounded profiles, which is particularly useful in small-batch production or repair work where repeatable checks are essential. For queries about fitment or to ensure the right configuration for a particular application, Metav’s technical team is available to advise on integration and best practice handling. Contact Metav Werkzeuge for bespoke advice on integrating the M240.232 into existing calipers and to confirm compatibility with specific measuring tasks; consultants in Emmerich will assist with technical details and dispatch options. Technical data Article number: M240.232 GTIN: 4061905053771 Material: stainless steel Weight: 0.08 kg Compatible with: Digital Uni Calipers series 240.201–240.205 Contact diameter: 4 mm Measuring face length: 70 mm Facts Contact diameter: 4 mm Measuring face length: 70 mm Weight: 0.08 kg SKU: M240.232 Special features Ball-shaped measuring face For external measurements from 42 mm Stainless steel construction Designed for retrofit to caliper series 240.201–240.205 FAQ How does the ball-ended face affect measurement results? The ball-ended face on the M240.232 creates a single, defined contact point that improves repeatability and reduces surface indentation compared with flat contacts, making it suitable for edges and slightly curved profiles. Which calipers are compatible with this insert? This insert is designed for the Digital Uni Calipers series 240.201–240.205 and is supplied as SKU M240.232 for direct identification during ordering. What material is used for the measuring face and how durable is it? The M240.232 is manufactured from stainless steel, offering corrosion resistance and mechanical robustness for routine workshop use. From which internal dimension can this insert be used for external measurement? The measuring jaw is intended for external measurements starting at an internal reference of 42 mm on the corresponding caliper configuration. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the precise contact geometry and corrosion‑resistant material to extend caliper functionality for delicate or rounded surfaces; the 7 x 2 mm tip and ball‑shaped measuring face ensure repeatable outside measurements on the Digital‑Uni caliper series. Order this insert directly via Metav Werkzeuge or consult the advisors for matching accessories. M240.231 Outside measuring insert — ball‑shaped measuring face, 7 x 2 mm, 70 mm length (Metav IndustryLine) A M240.231 outside measuring insert designed to convert a Digital‑Uni caliper into a specialist gauge for rounded or sensitive components, enabling reliable point contact where standard jaws are unsuitable Ball‑shaped contact for delicate and rounded surfaces Stainless steel construction for corrosion resistance Compatibility with Digital‑Uni Series 240.201–240.205 Reliable contact on curved and delicate geometries The ball‑shaped measuring face provides a defined point of contact that minimises surface damage and concentrates force predictably, which is particularly useful for measuring radii, small domes or parts with fragile finishes. With a compact 7 x 2 mm tip and a nominal working length of 70 mm, this insert converts a standard caliper into a specialist tool without compromising handling. The intentional contact geometry improves precision by reducing ambiguous contact points common with flat jaws. Durable material for workshop and inspection environments Machined from stainless steel, the measuring insert resists corrosion and maintains surface integrity in humid or coolant‑rich environments. The small mass and compact profile contribute to repeatability during routine checks: the unit’s light weight (0.08 kg) lowers inertia, easing manual positioning and reducing measurement variation caused by excessive leverage. The robust material also supports repeated cleaning and decontamination, extending service life and keeping maintenance straightforward. Seamless integration to accelerate inspection workflows Designed for plug‑and‑play use with the Digital‑Uni caliper series 240.201–240.205, the insert simplifies tool changes and reduces downtime in mixed‑part inspection routines. Its defined contact point shortens setup and alignment times, supporting faster batch checks and a more efficient quality process. Where traceable or specialised measurement procedures are required, the clear mechanical function of the insert makes documentation and process planning easier without adding complexity to the metrology chain. Contact Metav Werkzeuge for tailored advice on fitting and delivery from Emmerich; technical consultants can confirm compatibility with existing Digital‑Uni calipers and recommend matching accessories — info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: M240.231 GTIN: 4061905053764 Description: Outside measuring insert 7 x 2 mm, ball‑shaped measuring face, length 70 mm for Digital‑Uni calipers series 240.201–240.205 Facts Tip dimensions: 7 x 2 mm Contact diameter: 2 mm Length: 70 mm Weight: 0.08 kg Special features Material: stainless steel Ball‑shaped measuring face for rounded or delicate surfaces Compatible with Digital‑Uni series 240.201–240.205 FAQ Are these inserts compatible with the Digital‑Uni caliper series? The M240.231 insert is made specifically for the Digital‑Uni caliper series 240.201–240.205 and fits the standard attachment points for those models. What types of measurements are suitable with this insert? The ball‑ended contact is intended for outside measurements on rounded edges, domes and delicate surfaces where flat jaws would risk deformation or ambiguous contact. What material is the insert manufactured from and how durable is it? The insert is manufactured from stainless steel, offering corrosion resistance and suitability for regular cleaning and use in workshop or inspection environments. Is a calibration certificate supplied with the insert? This listing does not indicate an included calibration certificate; calibrated variants or procedure advice can be provided on request through Metav Werkzeuge. How is the insert mounted and aligned on the caliper? The insert mounts into the caliper’s designated external jaw attachment; alignment should be checked by a short reference measurement to ensure correct seating and repeatability Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, purpose‑built internal measuring insert that combines durable stainless steel construction with a rounded measuring face for reproducible contact and minimal part damage; the design is optimised for internal measurements starting at 26 mm and integrates directly with the Digital‑Uni caliper family for fast retrofit. Order via Metav Werkzeuge or consult our specialists for compatibility advice. M240.241 internal measuring insert for Digital‑Uni calipers – stainless steel, rounded face The M240.241 is an internal measuring insert designed for internal measurements from 26 mm, offering a 7 x 2 mm profile and a ball‑shaped measuring face for secure contact in confined bores on Digital‑Uni calipers series 240.201–240.205. Internal measuring insert from 26 mm Rounded (ball) measuring face for safe contact Compatible with Digital‑Uni calipers series 240.201–240.205 Consistent internal contact for repeatable results The insert is engineered to provide repeatable internal measurement where restricted access or delicate surfaces demand a gentle touch. The rounded measuring face distributes contact force more evenly than a sharp tip, reducing local indentation and producing more consistent results on bore diameters. Made from stainless steel, the measuring tip resists corrosion and maintains geometric integrity under frequent use, supporting stable measurement routines in workshop and inspection settings. This construction helps the measuring system preserve calibration and reduces downstream rework. Compact geometry that fits tight bores and precision tools With a slender 7 x 2 mm profile and a measuring section specified at 70 mm length, the insert is suited to small‑diameter bores and deep features where standard jaws are impractical. The slim profile enables access without extensive modification to the caliper, so integration into existing measuring setups is efficient. The part’s low mass (approx. 0.08 kg) minimises inertial effects, which supports steady handling and precise positional control during measurement cycles on both manual and semi‑automated inspection stations. Direct compatibility reduces setup time Designed specifically for the Digital‑Uni calipers series 240.201–240.205, this insert allows rapid replacement of existing internal jaws with minimal tooling. Compatibility ensures that digital readout characteristics and mechanical alignment are preserved, so traceability and measurement documentation remain consistent. The insert’s geometry was chosen to match the mounting and guidance of the host calipers, avoiding the need for special adapters and thereby reducing machine downtime during tool changes. Practical benefits for production and quality control The combination of a ball‑shaped contact and stainless material makes the component a reliable choice for repeated internal checks, particularly during in‑process inspection or final quality control. The insert supports precise bore verification without marking, which is beneficial when working with finished surfaces or soft materials. For procurement managers and metrology technicians, this means a straightforward upgrade path to improve measurement coverage while keeping existing instruments in service. Contact Metav Werkzeuge for tailored technical advice and to secure the M240.241 internal measuring insert for seamless integration into the Digital‑Uni caliper family; call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss delivery and compatibility details Technical data Article number: M240.241 GTIN: 4061905053818 Weight: 0.08 kg Material: stainless steel Measuring face length: 70 mm Internal measurement start: 26 mm Compatibility: Digital‑Uni calipers series 240.201–240.205 Core specifications Diameter: 2 mm Profile: 7 x 2 mm Applicable measurement: internal Mass: 0.08 kg Special features Ball‑shaped (rounded) measuring face Corrosion‑resistant stainless steel construction Designed for direct retrofit into listed Digital‑Uni calipers FAQ Is this insert suitable for all Digital‑Uni calipers? The insert is compatible with the Digital‑Uni calipers series 240.201–240.205; compatibility with other models should be confirmed against the caliper’s mounting interface. What is the measuring range for internal measurement? The insert enables internal measurements starting at 26 mm, providing access into bores and recesses beyond that diameter. Will the rounded measuring face mark fragile surfaces? The ball‑shaped measuring face is intended to reduce point loading and therefore lowers the risk of marking compared with sharp tips; material and finish of the workpiece will still influence contact behaviour. Can the insert be used for external measurements? This component is designed as an internal measuring insert; external measurement suitability is not provided and should be handled with purpose‑built external jaws. What material is the insert made from and why does it matter? Constructed from stainless steel, the insert offers corrosion resistance and dimensional stability, which supports longevity and repeatable measuring performance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise internal contact geometry and robust stainless construction to achieve repeatable readings in confined bores; the ball-shaped measuring face and 70 mm effective length reduce point-load errors for smoother inspection cycles. Order the insert directly via Metav Werkzeuge or ask the consultants for compatibility guidance. M240.242 Internal Measuring Insert — ball-shaped face, 70 mm effective length for Digital‑Uni calipers M240.242 is an internal measuring insert designed for internal measurements from 28 mm and intended for use with the Digital‑Uni calipers series 240.201–240.205. Ball-shaped measuring face for reliable contact 70 mm effective measuring length for internal fits Stainless steel construction for corrosion resistance Compatible with Digital‑Uni calipers 240.201–240.205 Reliable contact geometry for confined bores The ballised tip delivers a defined contact point that reduces sensitivity to minor misalignment during internal measurement, helping to produce repeatable readings in small-diameter bores. By concentrating the contact on a radially curved face, the insert avoids sharp point loading that can skew results; this behaviour is particularly helpful when inspecting bore seats, counterbores or stepped interiors where conventional flat jaws can produce variable contact. The result is faster decision-making in quality checks and fewer retests. Robust stainless design for workshop conditions Manufactured from stainless steel, the measuring insert offers corrosion-resistant performance in mixed workshop environments and resists wear at the contact face for extended service life. The 70 mm effective length balances access into deeper features with sufficient rigidity to limit deflection, which supports stable measurements across repetitive cycles. The compact mass also minimises added inertia to the caliper slider, preserving the instrument’s normal handling characteristics. Seamless integration with Digital‑Uni calipers and inspection workflows Engineered specifically for the Digital‑Uni calipers (series 240.201–240.205), this attachment installs simply onto the existing jaw mount and restores internal measuring capability from 28 mm upwards without complex adjustments. For production lines and bench inspection, the insert streamlines transitions between external and internal checks and reduces set‑up time for small-batch runs. Calibration intervals remain dictated by in‑house procedures; the accessory supports consistent traceability when combined with routine caliper verification. Contact Metav Werkzeuge for personalised compatibility advice or to arrange purchase of the M240.242 insert; our consultants in Emmerich can confirm fitment with existing Digital‑Uni calipers and advise on inspection integration Technical data Article number: M240.242 GTIN: 4061905053825 Weight: 0.08 kg Material: stainless steel Diameter: 4 mm Effective length: 70 mm Internal measurement from: 28 mm Compatible series: 240.201–240.205 Facts ECLASS: 21170324 SKU: M240.242 Special features Ball-shaped measuring face Corrosion-resistant finish Lightweight attachment for caliper slider FAQ What measurement range does the insert cover for internal measurements? The insert enables internal measurements from 28 mm upwards when fitted to the compatible Digital‑Uni calipers in series 240.201–240.205. Is the measuring face designed to reduce measurement variability? Yes, the ball-shaped measuring face of the M240.242 provides a defined contact geometry that reduces point-load effects and improves repeatability in confined bores. Can the insert be used on any caliper brand? The accessory is designed for the Digital‑Uni calipers (series 240.201–240.205); fitment on other brands may require verification — Metav Werkzeuge can advise on cross‑compatibility. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combines Ø 15 mm precision contact, conical measuring faces and stainless-steel robustness for reproducible bore-centre checks; compatible with the digital uni calipers series 240.201–240.205. Order the attachment directly via Metav Werkzeuge or consult our specialists for application support. M240.253 Bore-centre measuring insert Ø 15 mm — Conical faces for digital uni calipers (Metav IndustryLine) A M240.253 bore-centre measuring insert designed as an accessory for digital uni calipers, providing focused contact geometry for reliable centre-to-centre measurements in bores and recesses. Compatible with digital uni calipers 240.201–240.205 Conical measuring faces for bore centres Stainless steel construction Ø 15 mm precision contact diameter Accurate centring for bore-to-bore measurements The attachment is engineered to convert a standard digital caliper into a dedicated bore-centre gauge: the conical measuring faces guide the contact point into the bore, reducing lateral play and improving repeatability. With a defined Ø 15 mm contact diameter the insert supplies a consistent reference area that simplifies the measurement of centre distance between two bores. This rational design reduces measurement scatter and supports faster quality decisions in daily inspection work. Robust, low-mass design for repeatable results Made from stainless steel, the accessory resists corrosion and retains geometric integrity under workshop conditions; its compact 48 mm length and light 0.08 kg mass keep the caliper balanced and easy to handle. The material choice and precise machining ensure long service life and minimal wear at the contact faces, which translates into lower maintenance and steady performance across repeated checks. Integrates into inspection routines and production workflows As a purpose-made caliper attachment, this measuring insert installs quickly on compatible digital units and supports straightforward measurement sequences for production and maintenance tasks. By converting existing calipers into specialised gauges, the component contributes to leaner tooling stocks and faster throughput while preserving measurement confidence. Backed by Metav’s distribution and quality filter in Emmerich, the Metav IndustryLine accessory benefits from established supply reliability and the company’s experience in precision metrology — a practical choice for shops aiming to democratise accurate measurement. For reliable bore-centre checks with the Metav IndustryLine M240.253, contact Metav Werkzeuge for application guidance or to request technical details at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M240.253 GTIN: 4061905053856 Category: Caliper accessory Facts Diameter: Ø 15 mm Weight: 0.08 kg Length: 48 mm Material standard: stainless steel ECLASS: 21170324 Special features Conical measuring faces for centring in bores Compatible with digital uni calipers series 240.201–240.205 Precise contact geometry for bore-centre measurements Caliper accessory for inspection and workshop use FAQ How is the M240.253 used to measure bore centres? The M240.253 is fitted to a compatible digital uni caliper and uses its conical measuring faces to centre in bores, allowing the caliper to capture accurate centre-to-centre distances. Is the insert suitable for corrosion-prone environments? Yes. The insert is manufactured from stainless steel, so the M240.253 offers enhanced resistance to corrosion in typical workshop conditions. Which caliper models are compatible with this attachment? Compatibility is specified for the digital uni calipers series 240.201–240.205; the insert was designed to integrate with those digital units. Does the measuring insert alter caliper handling significantly? The component is compact and lightweight (0.08 kg, 48 mm), preserving the balance and one-handed usability of the instrument while adding specialised bore-centre capability. Can the accessory be used for non-circular features or shallow bores? The conical contact geometry is optimised for standard bores; for irregular or very shallow features, measurement strategy should be reviewed and, if necessary, Metav Werkzeuge’s technical team can advise on suitability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of Ø 5 mm cone measuring faces and stainless-steel durability for fast, repeatable bore‑centre checks; order the accessory directly via Metav Werkzeuge or consult our specialists if required. M240.251 Hole‑distance measuring insert Ø 5 mm — cone measuring faces for Digital Uni calipers (series 240.201–240.205) | Metav IndustryLine M240.251 is a hole‑distance measuring insert with Ø 5 mm cone measuring faces, engineered for precise centre‑to‑centre measurement of bores when used with the Digital Uni caliper series 240.201–240.205. Ø5 mm cone tips for precise bore centres Stainless steel construction for corrosion resistance Compatible with Digital Uni calipers 240.201–240.205 Precise bore‑centre measurement for reliable inspection results The cone geometry with Ø 5 mm tips converts radial contact into a reproducible datum for centre‑to‑centre checks, reducing alignment errors that commonly occur with flat probes. Fitted to a digital caliper, the insert enables rapid verification of hole patterns and pitch, supporting consistent pass/fail decisions on the shop floor. The measured signal is as dependable as the mechanical contact; the shaped faces centre reliably in round bores and minimise lateral play, which improves traceability of measurements across batches. Robust stainless‑steel design that endures workshop conditions Constructed from stainless steel, the accessory resists corrosion and maintains form under regular handling, ensuring sustained accuracy over time. The compact 35 mm length and low mass (approx. 0.04 kg) make the insert easy to mount and manoeuvre without adding appreciable inertia to the caliper, preserving the instrument’s handling characteristics. Long service life and low maintenance reduce downtime and support continuous inspection routines in production or maintenance environments. Seamless integration to speed up measurement workflows Prepared for direct attachment to the Digital Uni calipers (series 240.201–240.205), the insert streamlines setup and reduces cycle times in repetitive checks. By converting a standard caliper into a specialised bore‑distance gauge, the accessory leverages existing tools and removes the need for dedicated jigs, which is a cost‑efficient approach for small to medium production runs. The result is improved throughput and a lower risk of rework thanks to quicker, more repeatable measurements. For precision bore‑centre inspections, choose the M240.251 from Metav Werkzeuge — contact our Emmerich team for tailored advice or compatibility checks via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M240.251 GTIN: 4061905053832 Brand: Metav IndustryLine Data Diameter: 5 mm Length: 35 mm Weight: 0.04 kg ECLASS: 21170324 Special features Cone measuring faces for bore‑centre measurement Compatible with Digital Uni calipers series 240.201–240.205 Material: stainless steel FAQ How does the insert measure hole distances accurately? The M240.251 uses Ø 5 mm cone measuring faces to centre inside a bore; when mounted on a Digital Uni caliper, it converts radial contact into a stable datum that yields repeatable centre‑to‑centre readings. Which calipers are compatible with this accessory? Compatibility is designed for the Digital Uni caliper series 240.201–240.205; the M240.251 mounts directly to those models to create a calibrated solution for bore‑pitch checks. Is the material suitable for regular workshop use? Yes, the insert is made from stainless steel, offering corrosion resistance and dimensional stability appropriate for frequent handling in production and inspection areas. Can the accessory reduce measuring time in serial inspections? By transforming a general‑purpose caliper into a specialised bore‑distance gauge, the M240.251 shortens setup and measurement cycles, improving throughput for repetitive quality checks. Does the insert affect caliper handling or weight significantly? With a length of 35 mm and a mass of approximately 0.04 kg, the accessory preserves the caliper’s handling characteristics while adding the necessary geometry for reliable bore measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from reliable bore‑centre readings thanks to the Ø 10 mm cone measuring faces and the stainless steel construction that ensures repeatable contact and corrosion resistance; order the insert directly via Metav Werkzeuge or ask our consultants for fitment guidance. Bore‑centre measuring insert Ø 10 mm — cone measuring faces for Digital Uni calipers (Metav IndustryLine) The Bore‑centre measuring insert Ø 10 mm is designed to extend a Digital Uni caliper into a specialised tool for measuring centre‑to‑centre distances of bores, combining compactness with workshop robustness. Cone measuring faces for bore‑centre checks Diameter Ø 10 mm for standard bores Corrosion‑resistant stainless steel Precise bore‑centre readings without added complexity This measuring insert converts a standard caliper into a stable gauge for bore‑centre evaluations by using cone measuring faces that seat reliably inside circular bores. The conical contact geometry centres the probe automatically, reducing lateral play and enabling repeatable measurements when paired with a compatible digital caliper. Because the accessory is machined from stainless steel, the contact surfaces retain shape under routine shop use and resist corrosion, which preserves measurement consistency over time. Seamless integration with Digital Uni calipers Fitting the insert to the intended Digital Uni caliper series 240.201–240.205 is straightforward: the accessory is a compact extension that uses the caliper’s jaws or mounting point to establish a fixed reference line between two bores. The cone ends provide defined points of contact inside holes, so the caliper’s linear readout translates directly into centre‑to‑centre distances without complex calculations. This approach leverages the caliper’s native resolution and user familiarity, maintaining procedural efficiency in inspection routines and small‑lot production checks. Robust design for everyday workshop use At a small mass and compact length, the insert is easy to handle and store while still offering the rigidity required for practical measurements. The stainless steel body resists wear from repeated seating in bores and simplifies cleaning after machining operations. The compact profile and modest weight improve operator handling and reduce the risk of inadvertent deflection during measurement, supporting consistent data capture across multiple parts and shifts. For compatibility confirmation and to obtain the M240.252 bore‑centre measuring insert with Ø 10 mm cone faces from Metav IndustryLine, contact Metav Werkzeuge GmbH by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants will advise on fitment and delivery options. Technical Data Article number: M240.252 GTIN: 4061905053849 Material: Stainless steel Weight: 0.05 kg Length: 44 mm Diameter: 10 mm Compatibility: Digital Uni caliper series 240.201–240.205 Facts Diameter: 10 mm Length: 44 mm Weight: 0.05 kg eClass: 21170324 Special features Cone measuring faces for bore‑centre measurement Corrosion‑resistant stainless steel Compact, lightweight accessory for caliper‑based checks Intended for caliper attachment to measure centre distances FAQ How does the insert measure bore‑centre distances? The M240.252 bore‑centre measuring insert seats its cone measuring faces inside holes so that the caliper’s linear travel reads the distance between the cone apices, converting directly to centre‑to‑centre values. Which calipers is this accessory compatible with? The insert is designed for the Digital Uni caliper series 240.201–240.205; compatibility with other models depends on the caliper’s jaw geometry and mounting arrangement. What material is the insert made from and why does that matter? The accessory is manufactured from stainless steel, which provides wear resistance and corrosion protection to preserve dimensional integrity and repeatability during regular workshop use. Is the insert suitable for bores other than 10 mm? The Ø 10 mm cone faces are optimised for bores around that diameter; they can function in slightly larger or smaller holes, but for best repeatability the bore should allow the cone to seat concentrically. Will using the insert change measurement accuracy compared with the caliper alone? The insert transfers the caliper’s linear measurement to a bore‑centre application; actual accuracy therefore depends on the caliper’s resolution and the operator technique, while the cone geometry improves centring and repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com