70mm Jaw R10x20 For Gauge Holder 9x10.5 Slot Set - Metav IndustryLine

Take advantage of precise R10 contact geometry, a compact 70 x 9 x 10.5 mm shank and the convenience of a set of two jaws for mirrored measuring tasks — a combination that supports repeatable results and simple retrofitting into common measuring fixtures. Order the accessory directly via Metav Werkzeuge or consult our specialists if required.

Measuring Jaw R10 x 20 mm — 70 x 9 x 10.5 mm shank (Metav IndustryLine)

A Measuring Jaw R10 x 20 mm designed as an accessory for precision measuring equipment and gauge fixtures, offering repeatable contact geometry for workshop and inspection use

• Precision R10 profile for repeatable contact
• Shank 70 x 9 x 10.5 mm for secure mounting
• Supplied as a set of 2 for left/right configurations
• Compatible with standard gauge holders

Consistent contact geometry that improves repeatability

The R10 tip profile provides a defined contact radius that reduces variability at the measuring interface, converting a complex contact condition into a repeatable reference. By using a controlled tip form rather than a blunt or undefined edge, the jaws generate more consistent seating on cylindrical or radiused features; this leads to repeatable measurement results and fewer re-measurements. The design is particularly useful in series inspection where the same contact condition must be reproduced across multiple parts.

Secure installation and immediate retrofit into fixtures

With a shank measuring 70 x 9 x 10.5 mm, the jaws are shaped to locate positively in standard accessory holders and gauge fixtures. The compact mounting dimensions make replacement and retrofit straightforward: the component can be fitted quickly without modification to the carrier, which minimises downtime and supports fast tool changes. Supplied as a set of 2, the pair allows mirrored mounting or simultaneous use for internal and external reference configurations.

Low mass and compact form for delicate measurement tasks

At approximately 0.01 kg per set member, the low mass reduces inertia on moving slides and helps preserve instrument dynamics during light-touch measurements. The compact cross-section ensures the jaws remain stiff over their short working length while keeping obstruction to the workpiece to a minimum. For applications where fine positioning and minimal probe force are important, the small footprint supports careful handling and precise alignment.

Practical benefits in daily inspection and metrology tasks

As a measuring accessory, the jaw set supports efficient workshop workflows by simplifying fixture setup and reducing variation between operators. The engineered contact profile cuts setup time by providing a reliable seating point, while the standardised shank dimensions ensure broad compatibility with gaugeholders and other metrology fixtures. For inspection environments that prioritise traceability and consistent measurement chains, the component forms a practical element in a quality-controlled process.

For retrofit, spares or project procurement of Metav IndustryLine measuring jaws, contact Metav Werkzeuge for tailored advice and ordering: email info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will ensure the correct configuration for the intended fixture or inspection task.

Technical data

• Article number: M317.108

• GTIN: 4054469127385

• Manufacturer brand: Metav IndustryLine

• Shank dimensions: 70 x 9 x 10.5 mm

• Measuring tip: R10 x 20 mm

• Length: 70 mm

• Weight: 0.01 kg

• Tariff number: 90173000

• Pieces per set: 2

• Supplied as a set of two jaws

• Intended use: accessory for measuring instruments and gauge fixtures

• Cross-section: 9 x 10.5 mm

• Category: Accessories (measuring devices)

FAQ

Are these jaws compatible with standard gauge holders?
The jaws feature a 70 x 9 x 10.5 mm shank and are designed for compatibility with common gauge holders and accessory carriers; verify the holder groove dimensions to ensure a positive fit.

What measuring profile do the jaws offer and why does it matter?
The R10 x 20 mm contact radius gives a defined seating geometry that improves repeatability and reduces measurement scatter compared with undefined edges.

Is the product supplied as a single item or a set?
The item is supplied as a set of 2 pieces, which supports mirrored mounting or paired use in inspection setups.

Can these jaws be used for internal and external measurements?
The geometry and compact size permit use in a variety of tasks; adaptation for internal or external reference depending on holder orientation is straightforward.

What is the product SKU for ordering or referencing?
The product is listed as SKU M317.108 for Metav IndustryLine.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com