200-500mm Gauge Block Holder Very Robust Design - Metav IndustryLine

Benefit from the very stable construction and the broad 200–500 mm clamping range for repeatable positioning; order the End gauge holder 200–500 mm directly via Metav Werkzeuge or ask our consultants if needed.

End gauge holder 200–500 mm — very stable construction, 200–500 mm clamping range (Metav IndustryLine)

The End gauge holder 200–500 mm is a precision mounting fixture for secure positioning and calibration of end gauges within a 200–500 mm span, designed for repeatable set-ups in workshop and calibration environments.

• Very stable construction for repeatable set-ups
• 200–500 mm clamping range
• Cross-section: 30×5 mm up to 300 mm
• Cross-section: 30×6.7 mm above 300 mm

Built for repeatable calibration and accurate positioning

The holder provides a stable construction that translates directly into repeatability during calibration cycles. Its engineered geometry keeps end standards aligned while measurements are taken, which reduces operator-induced variation and supports consistent results across batches. By fixing the reference gauge in a rigid fixture, metrology procedures become more reliable and traceable, helping to meet internal quality checks and external audit requirements without guesswork.

Robust profile reduces deflection and eases handling

The two cross-section profiles — 30×5 mm for spans up to 300 mm and 30×6.7 mm for longer spans — are chosen to balance stiffness with manageable weight. The holder weighs 0.4 kg, which aids quick set-up yet maintains sufficient rigidity for precise positioning. This combination minimises bending over the clamping length and shortens preparation time, so measurement technicians can complete more calibrations with stable reference points and fewer re-measures.

Suitable for workshop use and calibration laboratories

As a purpose-built fixture for end gauges, the unit integrates into routine measurement workflows and complements existing calibration equipment. The robust design is ideal for repeated use in production inspection stations as well as in dedicated calibration benches. Backed by Metav IndustryLine quality and the distribution strength of Metav Werkzeuge, the holder supports the democratisation of precision by making dependable metrology tools available to a broad range of users, from small workshops to specialised inspection labs.

Choose Metav IndustryLine's End gauge holder 200–500 mm for stable, repeatable calibration — contact Metav Werkzeuge for tailored advice and reliable supply direct from Emmerich

Technical data

• Article number: M317.207
• GTIN: 4054469127538
• Category: Endmasse
• Weight: 0.4 kg
• Country tariff number: 90173000

Facts

• Clamping range: 200–500 mm
• Cross-section up to 300 mm: 30×5 mm
• Cross-section above 300 mm: 30×6.7 mm

Special features

• Very stable construction
• Intended for positioning end gauges and calibration
• Suitable for workshop and laboratory use
• Brand: Metav IndustryLine

FAQ

What clamping range does the holder cover?
The End gauge holder 200–500 mm from Metav IndustryLine covers a clamping range of 200–500 mm, allowing mounting of end standards across that span.

How do the cross-section sizes affect performance?
The 30×5 mm profile (up to 300 mm) and the 30×6.7 mm profile (above 300 mm) increase stiffness with length; the Metav IndustryLine End gauge holder M317.207 therefore reduces deflection for longer spans.

Is the holder suitable for calibration benches?
Yes, the holder is engineered for repeatable set-ups and is suitable for both workshop inspection stations and calibration benches when used with appropriate end gauges.

What is the weight of the fixture and how does that influence handling?
The fixture weighs 0.4 kg, which balances ease of handling with sufficient rigidity for stable positioning during measurement tasks with the Metav IndustryLine holder.

Can the holder be used with standard end gauges?
The design of the End gauge holder 200–500 mm accommodates standard end gauges for precise positioning and calibration; Metav IndustryLine’s fixture is intended to simplify and stabilise gauge mounting.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com