110x65x35 mm Foot for End Gauge Holder Very Sturdy Construction - Metav IndustryLine

Benefit from a very stable construction and compact dimensions that deliver repeatable calibration results and reduced measurement uncertainty; order the foot directly via Metav Werkzeuge or ask our consultants if needed.

M317.211 – Foot for end gauge holder, 110 x 65 x 35 mm, very stable construction (Metav IndustryLine)

A M317.211 foot engineered to provide a rigid support for end gauge holders in precision metrology and calibration environments.

• Very stable construction for repeatable measurements
• Compatible with series 317.20X holders
• Compact footprint 110 x 65 x 35 mm
• Solid 1.2 kg mass for vibration damping

Solid base that boosts measurement consistency

The rigid base reduces micro-movements during contact and is therefore crucial for repeatable calibration cycles. With external dimensions of 110 x 65 x 35 mm and a mass of 1.2 kg, this foot provides a low centre of gravity and passive vibration damping, making measurements less sensitive to ambient disturbances. The robust build, described as very stable construction, supports consistent results when paired with end gauge holders and eliminates the need for frequent repositioning, which shortens set-up time and improves throughput in routine quality checks.

Compatibility that simplifies workshop workflows

Designed for integration with the 317.20X holder family, the foot fits directly to the corresponding holders and supports standard end gauge setups. It is explicitly compatible with the caliper-type gauges identified as M317.203 and M317.206, ensuring straightforward replacement or retrofitting in existing benches. The compact footprint and predictable mechanical interface reduce fixture complexity and allow the metrology bench to remain uncluttered, which benefits both small workshops and larger inspection cells where space and reproducibility matter.

Cross-section options explained for larger measuring ranges

The foot accommodates bar cross-sections used with end gauges: for measuring lengths up to 300 mm the prescribed cross-section is 30 x 5 mm, while for larger spans the profile increases to 30 x 6.7 mm. This graduated cross-sectional approach improves profile stiffness where required and helps maintain alignment over longer measuring spans. Explaining this in practical terms: the thicker profile for larger gauges resists bending and ensures that dimensional references remain parallel, which in turn reduces measurement scatter in medium‑to‑large workpieces.

Built for industrial use and routine calibration

The component is manufactured to withstand regular handling on the shop floor and is suitable for integration into calibration routines. Its mass and geometry are chosen to deliver a stable reference without adding unnecessary bulk to the metrology station. As part of an end gauge system, the foot supports traceable, repeatable measurements and is suitable for daily quality control tasks as well as periodic calibration campaigns where mechanical stability is a prime requirement.

For precise integration advice or to order the M317.211 foot for end gauge holders, contact Metav Werkzeuge to discuss compatibility with existing equipment and supply options.

Technical data

• Article number: M317.211
• GTIN: 4054469157382
• Category: Endmasse
• Tariff number: 90173000

Facts

• Dimensions: 110 x 65 x 35 mm
• Mass: 1.2 kg
• Cross-section up to 300 mm: 30 x 5 mm
• Cross-section from 300 mm: 30 x 6.7 mm

Special features

• Very stable construction
• Compatible with series 317.20X holders
• Suitable for use with M317.203 and M317.206 calipers
• Compact design for stable calibration setups

FAQ

What is the primary function of this foot?
The foot serves as a rigid base for end gauge holders, providing mechanical stability for repeatable measurement and calibration.

Which holders and calipers are compatible with the foot?
Compatibility is specified for the 317.20X holder series and the caliper items M317.203 and M317.206; it is intended as a direct support for these configurations.

How does the cross-section change with gauge length?
For measuring lengths up to 300 mm the cross-section is 30 x 5 mm; for lengths beyond 300 mm the profile increases to 30 x 6.7 mm to preserve stiffness.

Is the foot suitable for routine industrial use?
Yes, the solid design and 1.2 kg mass ensure resistance to shop-floor disturbances and support routine calibration and inspection tasks.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com