70x60x8 mm Holder for Gauge Block Holder Very Sturdy For Horizontal Use - Metav IndustryLine

Benefit from the combination of very stable construction, a compact 70 × 60 × 8 mm footprint and dedicated anti‑tilt support for reliable horizontal calibration results — order the holder directly via Metav Werkzeuge or ask our consultants if needed

Holder for end gauge support M317.213 — horizontal mounting, very stable construction (Metav IndustryLine)

The Holder for end gauge support M317.213 is a compact bracket designed to prevent lateral tipping during horizontal calibration and measurement setups for end gauges

• Very stable heavy-duty construction
• Horizontal mounting prevents lateral tipping
• Compact 70 × 60 × 8 mm footprint

Consistent calibration through stable support

A mechanically robust support reduces variability during bench calibration and repeat measurements. The bracket’s very stable construction and anti‑tilt design keep the gauge datum aligned under horizontal mounting conditions, which directly improves precision and repeatability in routine checks. Where measurement drift is costly, this support secures the end gauge so that comparative readings remain consistent and reproducible between successive calibrations, helping to maintain quality control documentation.

Small footprint with workshop resilience

The compact 70 × 60 × 8 mm dimensions combine a minimal footprint with a design that resists flexing under typical workshop loads. The unit’s modest weight makes handling straightforward while its construction prioritises profile stiffness to avoid unwanted movement; this leads to fewer setup iterations and faster throughput on the calibration table. The result is a space‑saving accessory that supports more reliable results without occupying valuable bench area.

Designed to fit common gauge configurations

Intended for use with end gauges and similar reference standards, the support accepts common cross‑section profiles: 30 × 5 mm for parts up to 300 mm and 30 × 6.7 mm for longer sections. This compatibility enables straightforward integration into established measurement routines and simplifies fixture planning for both bench and light production environments. The anti‑tilt feature is particularly useful when gauges are used in a horizontal orientation for comparative or verification tasks.

Practical workshop benefits and supplier confidence

The support reduces handling‑related errors and shortens setup time, which together raise productive measurement capacity on the shop floor. Sourcing from Metav IndustryLine brings the advantage of a focused supply channel: reliable availability and a quality filter based in Emmerich that supports consistent standards. The compact bracket is therefore a practical, low‑risk addition to calibration kits and inspection benches seeking improved stability for horizontal measurements.

For robust horizontal end‑gauge support and application advice, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com to discuss the M317.213 and its suitability for specific measurement setups

Technical data

• Article number: M317.213
• GTIN: 4054469158211
• Eclass: 21170108
• Tariff number: 90173000

Facts

• Dimensions: 70 x 60 x 8 mm
• Weight: 0.4 kg
• Cross‑section up to 300 mm: 30 x 5 mm
• Cross‑section from 300 mm: 30 x 6.7 mm

Special features

• Very stable construction
• For horizontal mounting
• Prevents lateral tipping
• Category: Endmasse

FAQ

What is the primary purpose of this holder?
The holder secures end gauges in a horizontal orientation to prevent lateral tipping and to support repeatable calibration and comparative measurements with the M317.213.

Which cross‑sections does the support accept?
The support is compatible with 30 × 5 mm profiles for components up to 300 mm and 30 × 6.7 mm profiles for longer items, matching typical gauge block and end‑gauge formats.

Is the bracket suitable for bench calibration of end gauges?
Yes, the bracket is intended for bench calibration use; its very stable construction reduces measurement scatter during horizontal setups.

Does the support require additional fixtures to hold standard end gauges?
In most cases the bracket functions as a direct support for standard end‑gauge profiles; specific fixture requirements depend on the gauge geometry and measurement procedure.

How does the holder improve measurement workflow?
By preventing tilt and improving datum stability, the holder shortens setup time and reduces repeat measurements, contributing to more efficient inspection cycles.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com