2-3mm Gauge Pin Set 100 Pc, 70mm Length, 0.01mm Steps, Special Steel, Case Included - Metav IndustryLine

Combining 0.01 mm graduation, special steel construction and a compact 70 mm pin length, this gauge pin set delivers repeatable diameter checks and robust workshop performance; order the product directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge Pin Set M318.852 — 2.00–3.00 mm, 0.01 mm graduation (Metav IndustryLine)

Gauge Pin Set M318.852 is a precision inspection set designed for verifying hole diameters and fit tolerances in the 2.00–3.00 mm range; suitable for workshop inspections, toolmaking and incoming quality control.

• High-precision 0.01 mm graduation
• Special steel construction for wear resistance
• 70 mm pin length for stable measurements

High-precision inspection where it matters

The gauge pins provide repeatable diameter checks with a fine 0.01 mm graduation that supports consistent decision-making during quality control. Known in industry practice as gauge pins, these inspection implements are ideal for confirming bore sizes, verifying assembly fits and cross-checking measuring instruments. The clear numerical stepping ensures minor deviations are detectable, which reduces the risk of accepting out-of-tolerance parts and helps to avoid costly rework. This precision level suits standard workshop and machine‑shop inspections while maintaining straightforward handling for routine checks.

Built for endurance and dimensional stability

Manufactured from special steel, the pins combine surface hardness with dimensional stability to withstand repeated use in demanding production environments. The 70 mm pin length increases the effective engagement depth, giving improved lateral stability during insertion and reducing measurement scatter compared with very short gauges. This robustness translates into longer service life and stable measurement results across production batches, supporting efficient inspection cycles and less frequent replacement or recalibration of the set.

Practical organisation and handling for fast workflows

The set is supplied as a ready grouping of sequential sizes covering the 2.00–3.00 mm range in 0.01 mm steps, enabling rapid selection of the nearest nominal size during inspection. Each pin’s finish and consistent shaft geometry make insertion and extraction predictable, which speeds up repetitive measurement tasks. The compact format of the pins simplifies storage and transport within the workshop environment and helps technicians maintain traceable measurement routines without complex procedures. Smooth handling reduces operator influence on results and supports more confident pass/fail decisions.

Integrating the set into quality procedures

As a pragmatic addition to a metrology bench, the pins support acceptance testing, go/no‑go checks and verification of small-bore tooling. Their repeatability enhances process capability monitoring and helps establish evidence in inspection reports. Where traceable documentation is required, Metav’s position as a precision partner ensures easy access to technical advice and further metrology products to complement the set, making the pins a practical component of a consolidated inspection strategy that reduces vendor complexity and keeps procurement centralised.

For reliable measurement performance from the Metav IndustryLine range, contact Metav Werkzeuge for tailored advice and procurement support at info@metav-werkzeuge.com or by phone.

Technical data

• Article number: M318.852
• GTIN: 4061905450174
• Brand: Metav IndustryLine

Facts

• Measurement range: 2.00–3.00 mm
• Graduation: 0.01 mm
• Pin length: 70 mm
• Weight: 1.82 kg

Special features

• Material: special steel
• Application: diameter and fit verification
• Category: gauge pin set
• Format: graduated sequential sizes

FAQ

What tolerance steps are included in the set?
The set is supplied with a 0.01 mm graduation across the 2.00–3.00 mm range, enabling fine increments for precise diameter verification with the Metav IndustryLine gauge pins.

Can these pins be used for both inspection and go/no‑go checking?
Yes; the pins serve for detailed inspection of bore diameters and for establishing reference fits in routine go/no‑go assessments within the specified measurement range.

What is the length of the pins and why does it matter?
Pins are 70 mm long, providing greater engagement depth and lateral stability during insertion, which improves repeatability compared with very short gauges.

Is the material suitable for workshop use with frequent handling?
The pins are made from special steel, chosen for wear resistance and dimensional stability, making them well suited to regular workshop inspection duties.

How does this set support a small metrology department?
By offering sequential sizes with fine graduation, the set simplifies diameter checks, speeds up inspection routines and integrates easily into existing quality procedures as part of a consolidated Metav IndustryLine toolkit.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com