1.05 mm Gauge Block, Hardened Special Steel, DIN EN ISO 3650 Grade 1 - Metav IndustryLine

Take advantage of the combination of DIN EN ISO 3650 Grade 1 accuracy, hardened special steel construction and compact cross‑section for dependable reference measurements in quality control; order the gauge via Metav Werkzeuge or contact our advisers for application support.

End gauge 1.05 mm – DIN EN ISO 3650, Grade 1 by Metav IndustryLine

A precision End gauge 1.05 mm intended as a calibrated reference for dimensional inspection and routine verification in inspection labs and production environments.

• DIN EN ISO 3650 Grade 1 accuracy
• Hardened special steel for longevity
• Compact cross-section 30×9 / 35×9 mm

Reliable reference for dimensional control

The DIN EN ISO 3650 specification and Grade 1 classification designate this gauge as a high‑accuracy reference suitable for validation of measuring instruments and short‑range inspection tasks. As a calibrated small‑sized end gauge, it provides a stable dimensional standard that supports traceable measurement chains and reduces uncertainty in pass/fail checks. The nominal size of 1.05 mm and the precise ground surfaces make this component practical for repeatable verification steps in workshop and laboratory routines.

Durable build for repeated use and low wear

Manufactured from hardened special steel, the piece resists deformation and preserves the measuring surfaces over extended use. The material selection emphasises wear resistance and dimensional stability, so routine contact with gauge blocks, comparator anvils or part seats does not quickly degrade the reference. With a mass of just 0.004 kg, handling is effortless while the hardness ensures the gauge remains a reliable benchmark for many inspection cycles.

Compact geometry that enhances handling and stability

The cross‑section follows practical dimensions: up to 10 mm nominal size the profile is 30×9 mm, and from 10.1 mm the profile is 35×9 mm. This geometry combines a low profile for insertion into fixtures with sufficient sectional stiffness to prevent twisting during measurement and comparison tasks. The compact format helps maintain alignment in gauge stands and reduces the risk of operator‑induced error, thereby supporting faster, more consistent checks on small parts and assemblies.

Suited uses and contribution to quality workflows

Designed for use in calibration benches, incoming inspection and periodic verification procedures, this item supports compliance activities and helps streamline quality assurance processes. Its adherence to recognised standards aids documentation and auditability; keeping reference artefacts like this to hand accelerates setup and minimises downtime during measurement tasks. Confidence in results increases when a traceable, grade‑specified gauge is used as the reference in routine checks.

Contact Metav Werkzeuge for application advice or to obtain the Metav IndustryLine end gauge and integrate a Grade 1 reference into inspection workflows; Metav’s specialists in Emmerich can advise on traceability and storage options.

Technical data

• Article number: M319.0105.1
• GTIN: 4054469130255
• Tariff number: 90173000
• Nominal size: 1.05 mm
• Weight: 0.004 kg
• Standard: DIN EN ISO 3650
• Grade: 1

Facts

• Nominal dimension: 1.05 mm
• Cross-section up to 10 mm: 30 × 9 mm
• Cross-section from 10.1 mm: 35 × 9 mm

Special features

• Material: Special steel, hardened
• Category: End gauges
• Application: Reference measurement and inspection

FAQ

What tolerance class does this end gauge conform to? The end gauge conforms to DIN EN ISO 3650, Grade 1, offering the accuracy expected for grade‑specified reference standards.

Which material is used for the gauge and what benefit does it provide? The gauge is made from hardened special steel, which provides long‑term wear resistance and dimensional stability for repeated comparative measurements.

Is the 1.05 mm gauge suitable for calibration benches and incoming inspection? Yes, the End gauge 1.05 mm is designed for use in calibration benches, incoming inspection and routine verification workflows where a stable, traceable reference is required.

How does the cross‑section affect handling and measurement stability? The defined cross‑sections (30×9 mm up to 10 mm and 35×9 mm from 10.1 mm) give a low profile for easy insertion while maintaining sufficient stiffness to reduce torsion and handling error.

Can this gauge be used as a routine production check standard? As a DIN EN ISO 3650 Grade 1 reference, this item is suitable for routine production checks when a high‑accuracy short‑range standard is required

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com