1.5 mm Gauge Block, DIN EN ISO 3650 Grade 0, Hardened Special Steel - Metav IndustryLine

Supplied as a single, 1.5 mm reference gauge with DIN EN ISO 3650 Grade 0 conformity and made from hardened special steel, this end measure offers dependable dimensional stability and handling comfort for workshop and laboratory use. Order the gauge block directly via Metav Werkzeuge or contact our consultants for application-specific advice.

Single gauge block 1.5 mm — Gauge block (DIN EN ISO 3650, Grade 0) by Metav IndustryLine

A single single gauge block 1.5 mm designed as a precision reference for dimensional measurement and inspection tasks in quality control and metrology.

• DIN EN ISO 3650 Grade 0 accuracy
• Hardened special steel construction
• Nominal size 1.5 mm reference standard
• Cross-section 30 x 9 mm for secure handling

Certified conformity that supports reproducible inspection results

The gauge block complies with DIN EN ISO 3650 and is specified as Grade 0, which positions it for routine metrology and workshop inspection where traceable, repeatable measurements are required. Made from hardened special steel, the block combines wear resistance with minimal dimensional change under normal use. The compact 1.5 mm nominal size makes it suitable as a base reference in gauge sets and for fine comparative measurements on small features, supporting consistent process control and reduced measurement uncertainty.

Robust geometry for safe handling and long-term stability

A defined 30 x 9 mm cross-section for sizes up to 10 mm ensures comfortable handling and stable seating when stacked or used singly. The material choice and the ground faces provide a balance of mechanical stability and thermal behaviour appropriate for shop-floor and laboratory environments. The modest mass contributes to reduced thermal drift during brief contact measurements while the hardened surface reduces wear over repeated use, extending functional lifetime and lowering lifecycle cost.

Practical advantages in calibration and inspection workflows

As a single end measure, this product simplifies the creation of reference stacks and the verification of comparison measuring equipment. The Grade 0 classification offers a clear, recognised standard for acceptance criteria and exchange with inspection reports and quality documentation. Its compact size facilitates storage in gauge sets or protective trays and enables ergonomic use during repetitive checks, increasing throughput in routine inspection sequences.

Compatibility and everyday use in the workshop and metrology lab

The element integrates easily into existing reference sets and is compatible with standard handling tools for gauge blocks. Its specification and form factor allow technicians to perform quick comparative checks, establish master references for bench instruments, or verify small features on components destined for assembly. For organisations seeking reproducible measurement chains, the gauge block provides a tangible, standards-based solution that contributes directly to fewer measurement-related rejections.

For procurement of the M319.015.0 single gauge block or for advice on integrating this reference into inspection routines, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for tailored guidance and supply.

Technical data

• SKU: M319.015.0
• GTIN: 4054469131146
• Designation: Single gauge block 1.5 mm, DIN EN ISO 3650, Grade 0

Key measurements

• Nominal size: 1.5 mm
• Weight: 0.007 kg
• Cross-section: 30 x 9 mm

Materials & standards

• Material: hardened special steel
• Standard: DIN EN ISO 3650 Grade 0
• Category: Gauge block (end measure)

FAQ

What does Grade 0 mean for this gauge block?
Grade 0 indicates conformity with DIN EN ISO 3650 for a general industrial reference level; the M319.015.0 is therefore specified for routine metrology and workshop inspection where recognised standardisation supports reproducible results.

Is this single gauge block suitable for building a reference stack?
Yes. The single gauge block is designed for stacking with other end measures and slip gauges to create reference heights or master values for comparative checks and calibration tasks.

How should the gauge block be cared for to preserve accuracy?
Store the block in a clean, dry environment and handle with clean gloves or tools to prevent oils and corrosion. Wipe contact faces with a lint-free cloth and suitable protector oil after use; avoid impacts and excessive temperature changes.

Can this element be used directly for instrument calibration?
The block is a precision reference intended for use in calibration and verification workflows; if a traceable calibration certificate is required, request the appropriate calibration service or documentation at the time of purchase.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com