5 mm Gauge Block Single End, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine

Take advantage of a compact, DIN EN ISO 3650-compliant length reference that combines high manufacturing quality with straightforward workshop handling; the hardened special steel construction and Grade 0 tolerance provide a reliable baseline for routine checks and setting tasks. Order this single gauge block directly via Metav Werkzeuge or consult our specialists for application advice.

Single gauge block 5 mm — durable Grade 0 length standard from Metav IndustryLine

A Single gauge block 5 mm designed as a primary length reference for inspection benches and workshop calibration tasks, offering stable geometry and conformity with DIN EN ISO 3650.

• Grade 0 accuracy to DIN EN ISO 3650
• Hardened special steel for dimensional stability
• Compact cross-section 30 x 9 mm for workshop use
• Nominal length 5 mm, mass 0.008 kg

Dependable reference for repeatable measurements

This compact length standard serves as a direct, high-quality reference when establishing or checking measuring instruments. As a Grade 0 gauge block produced to DIN EN ISO 3650, it supplies the repeatability required for everyday calibration work and makes a tangible difference in process reliability. The item functions as a stable baseline for verifying micrometres, vernier calipers and comparator setups, reducing downtime caused by uncertain references and simplifying routine verification procedures.

Robust construction that supports consistent results

Manufactured from hardened special steel, this gauge block resists wear and preserves its geometry across many handling cycles. The prescribed cross-section 30 x 9 mm (applicable for nominal lengths up to 10 mm) provides a favourable stiffness-to-weight ratio, so the standard remains easy to position while minimising deformation under normal contact forces; the mass is approximately 0.008 kg. These attributes translate into fewer re-measurements and a lower risk of incidental distortion during set-up, which in turn supports faster, more reliable inspection routines.

Practical integration into workshop workflows

The piece is intended as a straightforward single block for direct use on the shop floor or in a measuring room. Its compact size and conformity to the recognised standard make it suitable for inclusion in master sets or as a stand‑alone reference for daily checks. Where traceability and repeatability matter, this block enhances measurement confidence through an established standard, enabling technicians to maintain consistent production quality and to document conformity more easily.

Choose the Metav IndustryLine single gauge block 5 mm for a compact, Grade 0 length standard and contact Metav Werkzeuge in Emmerich for ordering details and practical advice on integration into existing quality procedures.

Technical data

• Article number: M319.050.0
• GTIN: 4054469131368
• Tariff number: 90173000
• Material: Special steel, hardened
• Nominal size: 5 mm
• Standard: DIN EN ISO 3650
• Grade: 0
• Mass: 0.008 kg
• Cross-section: 30 x 9 mm (≤ 10 mm)

Facts

• Nominal length: 5 mm
• Weight: 0.008 kg
• Cross-section dimensions: 30 x 9 mm
• GTIN: 4054469131368
• Tariff number: 90173000

Special features

• DIN EN ISO 3650 compliant
• Grade 0 accuracy
• Hardened special steel construction
• Compact workshop-sized gauge block
• Single end measure suitable for master sets

FAQ

What tolerance class does this gauge block meet?
The single gauge block 5 mm meets Grade 0 tolerances according to DIN EN ISO 3650, providing a precision level suitable for workshop calibration and routine inspection.

Is the material suitable for frequent use in a workshop environment?
Yes. The gauge block is made of hardened special steel, which offers wear resistance and stable geometry under normal handling typical for shop-floor use.

Can this block be used as a reference for setting micrometres and calipers?
Yes. The 5 mm block from Metav IndustryLine is intended as a reference for setting and checking micrometres, vernier calipers and similar length gauges.

What are the physical dimensions and mass of the block?
The nominal length is 5 mm, cross-section 30 x 9 mm (for nominal sizes up to 10 mm), and mass approximately 0.008 kg.

Which article number should be quoted when ordering or requesting documentation?
Please quote article number M319.050.0 (GTIN 4054469131368) when ordering or asking for technical documentation.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com