9 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine

Take advantage of a compact length standard that combines traceable conformity, hardened special steel construction and a cross-section optimised for handling; the result is precise, repeatable measurements with a small footprint. Order directly via Metav Werkzeuge or contact our consultants for specification and supply details.

Gauge block 9 mm — hardened length standard, DIN EN ISO 3650, Grade 1

The gauge block 9 mm is a hardened, high‑accuracy length standard intended for calibration tasks and dimensional checks in industrial metrology and laboratory environments.

• DIN EN ISO 3650 Grade 1 accuracy
• Hardened special steel construction
• Compact cross-section 30 x 9 mm for stable handling
• Traceable identification with GTIN and SKU

Precision that supports reliable quality control

This length standard is manufactured to DIN EN ISO 3650 and shipped as Grade 1, which communicates a predictable tolerance band suitable for routine and elevated inspection tasks. The compact nominal size of 9 mm stabilises thermal behaviour and reduces handling errors, while the hardened special steel substrate delivers surface integrity and wear resistance. As a consequence, this precision gauge provides a consistent reference for setting micrometres, calipers and optical comparators, supporting faster decisions on conformity and reducing downtime in measurement workflows.

Robust form for repeatable measurements

A cross-section of 30 x 9 mm (applies for nominal sizes up to 10 mm) gives the block a practical balance between mass and manoeuvrability: it is heavy enough to sit steadily during measurements yet small enough for rapid alignment in a set. The hardened finish minimises surface distortion and prolongs service life under regular use. At roughly 0.01 kg, handling is effortless and integration into existing gauge sets or storage systems is straightforward. Bold surface quality and consistent geometry together mean fewer rechecks and a dependable master for day‑to‑day inspection routines.

Traceability and integration into calibration regimes

The product is supplied with clear identification (SKU M319.090.1 and GTIN 4054469131535), which simplifies inventory and traceability within quality management systems. As a standardised length artefact, this block serves both as a direct calibration reference and as part of comparative checks that support internal audits and external conformity records. The hardened construction reduces the frequency of recalibration caused by wear, contributing to lower total cost of ownership over a measurement asset’s lifecycle. Where traceability chains and documented calibration history are required, this gauge block fits into established workflows and laboratory procedures.

Practical benefits for workshop and laboratory use

Because this block adheres to an international standard and is produced from hardened special steel, it is suitable for repeated contact with precision instruments without rapid degradation. The small form factor makes it an efficient choice for toolrooms, inspection benches and portable calibration kits, while the clear SKU and GTIN support procurement, stock control and digital asset tracking. Pairing standard conformity with a wear‑resistant material gives technicians a compact, reliable reference that keeps inspection throughput steady and predictable.

Contact Metav Werkzeuge to confirm suitability for specific calibration chains and to arrange supply from Emmerich with full product documentation

Technical Data

• Article number: M319.090.1
• GTIN: 4054469131535
• SKU: M319.090.1
• Category: Endmasse

Facts

• Nominal size: 9 mm
• Standard: DIN EN ISO 3650
• Grade: 1
• Weight: 0.01 kg
• Customs tariff number: 90173000

Special features

• Material: special steel, hardened
• Cross-section: 30 x 9 mm (for nominal sizes ≤ 10 mm)
• Intended use: length standard for calibration and dimensional checks
• Packaging: standard commercial packing for measurement tools

FAQ

What level of accuracy does this gauge block provide?
This Grade 1 gauge block meets the tolerance band specified by DIN EN ISO 3650 and is intended for reliable workshop and inspection use where traceable conformity is required.

Is the block suitable for inclusion in a master set for daily inspection work?
Yes; the hardened special steel construction and compact cross-section make it a practical master reference within a gauge block set or portable calibration kit.

How is the product identified for inventory and traceability?
Identification is supported by SKU M319.090.1 and GTIN 4054469131535, enabling straightforward recording in quality management systems and procurement workflows.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com