23 mm Gage Block Grade 0 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine

Combine Grade 0 accuracy, hardened special steel and conformity to DIN EN ISO 3650 for a dependable reference standard; order directly via Metav Werkzeuge or consult our specialists for selection and availability.

Single gauge block 23 mm – Grade 0, DIN EN ISO 3650 (Metav IndustryLine)

A single gauge block 23 mm designed as a compact reference for calibration benches and precision inspection tasks

• Grade 0 accuracy (DIN EN ISO 3650)
• Hardened special steel construction
• Nominal length 23 mm for reference measurements

Precision where traceable measurement matters

The single gauge block 23 mm is manufactured to Grade 0 tolerance under DIN EN ISO 3650, providing a reliable reference measurement for calibration and quality control. As a high‑precision end measure, it offers the reproducibility required for acceptance checks, gauge set expansion and comparative measurements. The compliance with the international standard ensures compatibility with established calibration procedures and laboratory routines, reducing measurement uncertainty in routine inspections.

Durable material for long service life and stability

Constructed from hardened special steel, the block combines wear resistance with dimensional stability across repeated use. The block’s applicable cross-section for this nominal length is 35 x 9 mm, delivering adequate stiffness for manual handling while remaining compact. With a nominal mass of 0.063 kg, the component is easy to manoeuvre on the bench without compromising the surface contact required for accurate stacks. The material choice and heat treatment contribute to low drift and prolonged calibration intervals, translating into lower maintenance effort.

Practical in workshop and laboratory workflows

Designed as a standalone reference or a complement to existing sets, this end measure fits into inspection routines for mechanical workshops and calibration laboratories alike. Its compact form factor supports quick set‑up for comparative checks and integration into gauge stacks. When used consistently within documented procedures, the block helps to streamline quality control, avoid rework and provide documented traceability for production batches. The straightforward geometry facilitates reliable mating with other standards and slip gauges.

Secure this Grade 0 gauge block through Metav Werkzeuge—contact our Emmerich team by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for specification advice and stock information.

Technical data

• Article number: M319.230.0
• GTIN: 4054469132082
• Standard: DIN EN ISO 3650
• Grade: 0
• Material: Special steel, hardened

Facts

• Nominal length: 23 mm
• Weight: 0.063 kg
• Cross-section: 35 x 9 mm (for lengths > 10.1 mm)
• Tariff number: 90173000

Special features

• End measure for reference and calibration tasks
• Compact, stiff geometry for repeatable contact
• Suitable for integration into gauge sets
• Category: Endmasse / Gauge block

FAQ

What tolerance and standard does this gauge block meet?
The single gauge block 23 mm is specified to Grade 0 in accordance with DIN EN ISO 3650, making it suitable as a precision reference in standardised inspection routines.

What material is used and why does it matter?
The block is made of hardened special steel, which provides wear resistance and dimensional stability; these properties help maintain measurement accuracy over repeated use.

Can this item be used with existing gauge sets?
Yes — the end measure is intended as a standalone reference or as a complement to existing sets and stacks; its nominal length and compact cross-section allow straightforward stacking and comparison.

Is the size and form factor suitable for workshop handling?
With a nominal length of 23 mm and a cross-section of 35 x 9 mm, the block is compact yet sufficiently stiff for reliable manual handling and bench work.

How is traceability ensured when using this reference standard?
Traceability is achieved by using the block in documented calibration procedures in line with DIN EN ISO 3650; for formal certificates or accredited calibration, refer to the provider’s calibration services (not specified in the product data).

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com